Which of the following statements describes how tectonic plates move?
A. They move from the crust to the core.
B. They move from the mantle to the inner core.
C. They move from the inner core to the outer core.
D. They move slowly on top of the mantle.

Answers

Answer 1

Answer:

D

Explanation:

The tectonic plates move on the mantle, sort of floating on it as they are part of the crust. When they collide things like mountain ranges form, and big earthquakes happen.


Related Questions

A ball of mass 0.3 kg is released from rest at a height of 8 m. How fast is it going when it hits the ground? (Gravity being equal to 9.8)

Answers

Answer:

Explanation:

Mass doesn't matter here because when something is falling, gravity plays fairly; an elephant falls at the same rate of acceleration as does a feather. What DOES matter is everything pertinent to the y-dimension of free-fall:

a = -9.8 m/s/s

v₀ = 0 (since the ball was held before it was dropped)

v = ??

Δx = -8 m (negative because the ball drops this far below the point from which it was released).

Putting all this together in one equation:

v² = v₀² + 2aΔx and filling in this equation:

v² = (0)² + 2(-9.8)(-8) and

v² = 156.8 so

v = 12.5 which rounds to 13 if you're using 2 sig figs, and rounds to 10 if you're only using 1 (which you should be, according to the way the numbers have been given in this problem)

A body weighing 50 N is placed on a wooden table. How much force is required to set it into motion? Coefficient of friction between the table and the body is 0.3.​

Answers

If the coefficient of static friction is 0.3, then the minimum force required to get it moving is equal in magnitude to the maximum static friction that can hold the body in place.

By Newton's second law,

• the net vertical force is 0, since the body doesn't move up or down, and in particular

F = n - mg = n - 50 N = 0   ==>   n = 50 N

where n is the magnitude of the normal force; and

• the net horizontal force is also 0, since static friction keeps the body from moving, with

F = F' - f = F' - µn = F' - 0.3 (50 N) = 0   ==>   F' = 15 N

where F' is the magnitude of the applied force, f is the magnitude of static friction, and µ is the friction coefficient.

Calculate the gravitational force between two bodies of masses 10kg and 55kg, if they are placed at a distance of 2m apart. ​

Answers

Answer:

F = 9.177*10^-9N

Explanation:

Gravitational force between the two bodies is expressed as;

F = GMm/r²

Given tha

M = 55kg

m = 10kg

r = 2m

G = 6.67408 × 10-11 m³ kg-1 s-2

Substitute;

F = GMm/r²

F = 6.67408 × 10-11*55*10/2²

F = 3,670.744× 10-11/4

F = 9.177*10^-9N

please help me with my question due tomorrow morning,

Answers

Answer:

D)7 1/2 or 15/2

Explanation:

Let's calculate Combined resistance of the parallel first

1/Rt= 1/2+1/6=4/6

Rt=6/4 which is also equal with 3/2

Now let's add it with the series one

Rt= 6+3/2

=15/2 And when we put that un a mixed fraction 7 1/2

1. Priya is responsible for collecting canned food along three different streets for her school's
annual Thanksgiving Food
Drive. She walks 300 m [N] along Oak Road, 500 m [E] along
Second Street, and then 150 m (S45°W) along Cross Ave. She completes the journey in 10
minutes
a. Draw a scale diagram of her trip.
b. Calculate her total distance, displacement, speed, and velocity.

Answers

Answer:

distance = 950 m

displacement = 439.2 m

speed= 1.58 m/s

velocity = 0.732 m/s

Explanation:

A = 300 m North

B = 500 m East

C = 150 m South west

Time, t = 10 minutes = 600 s

(A) The diagram is given below.

(B) Total distance = 300+ 500 + 150 = 950 m

[tex]A = 300 \widehat{j} \\\\B = 500\widehat{i}\\\\C = - 150 (cos 45 i+ sin 45 j) = - 106 \widehat{i} - 106 \widehat{j}\\\\D = A + B + C \\\\D = 394 \widehat{i} + 194 \widehat{j}\\\\D=\sqrt{394^2 +194^2} = 439.2 m[/tex]

Speed = distance / time = 950/600 = 1.58 m/s

velocity = 439.2 / 600 = 0.732 m/s

Astronomers observe the Small Magellanic Cloud (SMC), a not very dense, rather small galaxy near us. They notice that even those stars that formed recently have relatively few heavier elements (when compared to such recent stars in our Milky Way.) What is the likely explanation for this deficiency

Answers

Answer:

The reason it has few heavier elements is due to the fact that it's stars are widely spaced and this implies that it's stars have very low rate of formation and termination.

Explanation:

The Small Magellanic Cloud, is basically a very tiny galaxy located near the Milky Way. Although it's tiny, it's diameter is approximately 7,000 light-years while it also contains over hundred million stars which are widely spaced.

Now, the reason it has few heavier elements is due to the fact that it's stars are widely spaced and this implies that it's stars have very low rate of formation and termination.

An unstrained horizontal spring has a length of 0.40 m and a spring constant of 340 N/m. Two small charged objects are attached to this spring, one at each end. The charges on the objects have equal magnitudes. Because of these charges, the spring stretches by 0.033 m relative to its unstrained length. Determine (a) the possible algebraic signs and (b) the magnitude of the charges.

Answers

Answer:

(a) Both the charges are positive or negative.

(b) Teh value of each charge is 1.53 x 10^-5 C.

Explanation:

Spring constant, K = 340 N/m

Natural length, L = 0.4 m

stretch, y = 0.033 m

(a) Let the charge on each sphere is q and they repel each other so the nature of charge of either sphere may be both positive or both negative.  

(b) The electrostatic force is balanced by the spring force.

[tex]\frac{kq^2}{(L + y)^2}=Ky\\\\\\\frac{9\times 10^9 q^2}{(0.4 +0.033)^2} = 340\times0.033\\\\q= 1.53\times 10^{-5} C[/tex]

The difference between starting and ending
positions is
distance
displacement

Answers

Answer:

displacement

Explanation:

Motion can be defined as a change in the location (position) of a physical object or body with respect to a reference point.

This ultimately implies that, motion would occur as a result of a change in location (position) of an object with respect to a reference point or frame of reference i.e where it was standing before the effect of an external force.

A reference point refers to a location or physical object from which the motion (movement) of another physical object or body can be determined.

Mathematically, the motion of an object is described in terms of acceleration, time, distance, speed, velocity, position, displacement, etc.

Displacement can be defined as the change in the position of a body or an object. It is a vector quantity because it has both magnitude and direction.

This ultimately implies that, the difference between the starting and ending positions of a physical object is generally referred to as displacement

Two planets are separated by a distance of 4.5x108 m. One of the planets has a mass of 2.1x1021 kg. The force of attraction between the planets is 5x1024 N. What is the mass of the other planet? (Be careful with your algebra!)

Answers

Answer:

The mass of the other planet is 7.23*10^(30) kg

Explanation:

For two objects of masses m₁ and m₂ respectively, separated by a distance r, the gravitational force between them is given by:

F = G*(m₁*m₂)/r^2

Where G = 6.67*10^(-11) m^3/(kg*s^2)

Here, we know that:

r = 4.5*10^8m

m₁ = 2.1*10^21 kg

F = 5*10^24 N

And we want to find the mass of the other planet, first, let's isolate m₂ in the force equation:

(F*r^2)/(G*m₁) = m₂

Now we can replace all the values that we know in the left side, and solve it:

m₂ =[(5*10^24 N)*( 4.5*10^8m)^2]/[6.67*10^(-11) m^3/(kg*s^2)*2.1*10^21 kg]

m₂ = 7.23*10^(30) kg

The mass of the other planet is 7.23*10^(30) kg

What is the dependent variable in this
experiment?
DONE
Biologists designed an experiment to test
the effect of compost on the development
of root crops. They tested several different
crops, including carrots, potatoes, beets,
and onions. They grew most of the plants
in the greenhouse, but due to space issues,
they had to grow some outdoors. They gave
all the plants the same amount of compost.
They obtained the compost from a local
farmer and from the local hardware store.
They ran out of the farmer's compost, so
some of the plants received that compost
when the seeds were planted and other
plants got hardware store compost after
the plants had already started growing.
What is the independent variable in this
experiment?
DONE

Answers

Answer:

"the plants had already started growing."

Explanation:

I think this is the answer because the definition of a dependent variable is the variable that is being affected by the change. Since the plants had already started growing BECAUSE of "They ran out of the farmer's compost, so

some of the plants received that compost

when the seeds were planted and other

plants got hardware store compost after

the plants had already started growing."

Sorry if I am wrong, I am just a 4th grader, pls don't hate on me, I am just trying to help :)

Answer:

It's compost

Explanation:

In case you needed the dependent variable, its the amount of plant growth

If your weight is 588N on the earth, how far should you go from the centre of the earth so that your weight will be 300N? The radius of the earth is 6400km and the value of g on the earth surface is 9.8m/s2.​

Answers

Answer:

Hmm, Well I am pretty sure the answer is 288N

Explanation:

I got the answer 288N but I am not sure if that is correct. Hope it helps! :D

A 1.25 kg block is attached to a spring with spring constant 17.0 N/m . While the block is sitting at rest, a student hits it with a hammer and almost instantaneously gives it a speed of 49.0 cm/s . What are You may want to review (Pages 400 - 401) . Part A The amplitude of the subsequent oscillations

Answers

Answer:

The amplitude of the subsequent oscillations is 13.3 cm

Explanation:

Given;

mass of the block, m = 1.25 kg

spring constant, k = 17 N/m

speed of the block, v = 49 cm/s = 0.49 m/s

To determine the amplitude of the oscillation.

Apply the principle of conservation of energy;

maximum kinetic energy of the stone when hit = maximum potential energy of spring when displaced

[tex]K.E_{max} = U_{max}\\\\\frac{1}{2} mv^2 = \frac{1}{2} kA^2\\\\where;\\\\A \ is \ the \ maximum \ displacement = amplitude \\\\mv^2 = kA^2\\\\A^2 = \frac{mv^2}{k} \\\\A = \sqrt{\frac{mv^2}{k}} \\\\A = \sqrt{\frac{1.25\ \times \ 0.49^2}{17}} \\\\A = 0.133 \ m\\\\A = 13.3 \ cm[/tex]

Therefore, the amplitude of the subsequent oscillations is 13.3 cm

how to Calculate the pressure on its base.

Answers

Answer:

p is =force x 10 whch is constant

Which of the following quantity is unit-less? 1 Specific gravity 2 Mass density 3 Acceleration due to gravity 4 All of the above​

Answers

Answer:

1

Explanation:

Specific gravity is a ratio (of 2 densities) so it has no unit.

If the particles that make up an object begin to move quickly, their average kinetic energy _____ and the object's temperature _____. Group of answer choices

Answers

Explanation:

If the particles that make up an object begin to move quickly, their average kinetic energy increases the object's temperature rises. Group of answer choices

A stone attached to a string is whirled round in a horizontal circle with constant speed of 10m/s .Calculate the difference in the velocity with the stone is at
I) opposite ends of a diameter
Ii) in two positions A and B where angle AOB is 90° & O is the centre of the circle ​

Answers

Answer:

Stop going on peoples pages and  answering random things kid, get a life

Learn to  solve  problems instead

Explanation:

I answered this because this kid just goes on random pages, and answers incorrectly for points. Check this egirl wannabe's profile

write any two difference between CGS and MKS system of measurement ?​

Answers

Answer:

MKS stands for Meter, Kilogram and second. In this system of unit mass is given in Kilogram, length in meter and time in second. ... CGS system stands for Centimeter- Gram- Second system. In CGS system, length is measured in centimeters mass is measured in grams and time is in seconds.

Define couple and give 2 examples

Answers

Answer:

Two equal and opposite parallel forces not acting along the same line, form a couple. A couple is always needed to produce the rotation.

For example, turning a key in a lock and turning a steering wheel.

A couple consists of two parallel forces that are equal in magnitude, opposite in sense and do not share a line of action. ... For example, the forces that two hands apply to turn a steering wheel are often (or should be) a couple. Each hand grips the wheel at points on opposite sides of the shaft.


A hamster in it's ball starts at rest and accelerates to 3ms1 in 6 seconds.
What was the distance the hamster travelled

Answers

Answer:9m

Explanation:

Ball starts from rest . Time taken = 6 seconds. Distance travelled by ball. ∴Distance travelled = 9 m

Hope it helps you

Good luck

A train is travelling at 50 m s−1 when the driver applies the brakes and gives the train a constant deceleration of magnitude 0.50 m s−2 for 100 s. Describe what happens to the train. Calculate the distance travelled

Answers

Answer:

The strain will come to rest after traveling some distance.

distance traveled = 2500 m

Explanation:

The strain will come to rest after traveling some distance.

Applying,

s = ut+at²/2................... Equation 1

Given: u = initial velocity, a = deceleration, t = time, s = distance

From the question,

Given: u = 50 m/s, t = 100s, a = -0.5 m/s²(deceleration)

Substitute these values into equation 1

s = 50(100)+(-0.5)(100²)/2

s = 5000-2500

s = 2500 m

Hence the distance traveled is 2500 m

please help me with this question​

Answers

Answer:

1. 12 V

2a. R₁ = 4 Ω

2b. V₁ = 4 V

3a. A = 1.5 A

3b. R₂ = 4 Ω

4. Diagram is not complete

Explanation:

1. Determination of V

Current (I) = 2 A

Resistor (R) = 6 Ω

Voltage (V) =?

V = IR

V = 2 × 6

V = 12 V

2. We'll begin by calculating the equivalent resistance. This can be obtained as follow:

Voltage (V) = 12 V

Current (I) = 1 A

Equivalent resistance (R) =?

V = IR

12 = 1 × R

R = 12 Ω

a. Determination of R₁

Equivalent resistance (R) = 12 Ω

Resistor 2 (R₂) = 8 Ω

Resistor 1 (R₁) =?

R = R₁ + R₂ (series arrangement)

12 = R₁ + 8

Collect like terms

12 – 8 =

4 = R₁

R₁ = 4 Ω

b. Determination of V₁

Current (I) = 1 A

Resistor 1 (R₁) = 4 Ω

Voltage 1 (V₁) =?

V₁ = IR₁

V₁ = 1 × 4

V₁ = 4 V

3a. Determination of the current.

Since the connections are in series arrangement, the same current will flow through each resistor. Thus, the ammeter reading can be obtained as follow:

Resistor 1 (R₁) = 4 Ω

Voltage 1 (V₁) = 6 V

Current (I) =?

V₁ = IR₁

6 = 4 × I

Divide both side by 4

I = 6 / 4

I = 1.5 A

Thus, the ammeter (A) reading is 1.5 A

b. Determination of R₂

We'll begin by calculating the voltage cross R₂. This can be obtained as follow:

Total voltage (V) = 12 V

Voltage 1 (V₁) = 6 V

Voltage 2 (V₂) =?

V = V₁ + V₂ (series arrangement)

12 = 6 + V₂

Collect like terms

12 – 6 = V₂

6 = V₂

V₂ = 6 V

Finally, we shall determine R₂. This can be obtained as follow:

Voltage 2 (V₂) = 6 V

Current (I) = 1.5 A

Resistor 2 (R₂) =?

V₂ = IR₂

6 = 1.5 × R₂

Divide both side by 1.5

R₂ = 6 / 1.5

R₂ = 4 Ω

4. The diagram is not complete

The brakes in car A and car B stop working and they need to stop. Car A and car B have the same mass. Car A is traveling at 30 miles per hour, smashes into a big wall, and is brought to rest in a collision that lasts for a fraction of a second. Car B was also traveling at 30 mph but it drives out into a field of grasses and sand and finally comes to rest after a bumpy 20 second ride. Which car gets the larger impulse?

Answers

Answer:

Both have equal impulse.

Explanation:

Let the mass of cars be m.

Then the Force acting on each of them for taking them to state of rest:

(Using Newton's second law of motion)

[tex]F_A=\frac{m\times (0-30)}{\Delta t_A}[/tex]

[tex]F_A=-30\frac{m}{\Delta t_A}[/tex] ...................................(1) (negative sign is associated with direction, here we are concerned about the magnitude only)

[tex]F_B=\frac{m\times (0-30)}{\Delta t_B}[/tex]

[tex]F_B=-30\frac{m}{\Delta t_B}[/tex] ...................................(2)

[tex]\because \Delta t_A<\Delta t_B[/tex]

[tex]\therefore F_A>F_B[/tex]

We know that impulse is given as:

[tex]J=F\times \Delta t[/tex] ........................................(3)

So, from eq. (1), (2) & (3)

[tex]J_A=F_A\times \Delta t_A[/tex]

[tex]J_A=-30m[/tex]

&

[tex]J_B=F_B\times\Delta t_A[/tex]

[tex]J_B=-30m[/tex]

Hence both have equal impulse.

Answer the question plz

Answers

Answer:

b and d

Explanation:

A car moves with the speed of 40 km/hr for the first half and 60 km/hr
for Second half distance "What is the average distance of cars.​

Answers

Answer:

50 km/h

Explanation:

[tex](40 + 60) / 2[/tex]

-> [tex]50[/tex] (km/h)

The atmosphere of Venus is mostly carbon dioxide, and the atmosphere of the Earth has water vapor. Why are these two gases absent in the atmosphere of the satellite around Saturn called Titan

Answers

Answer:

if these gases existed in Titan, this n in solid form, by which its absence in the atmosphere is understood.

Explanation:

Each gas and chemical compound has a defined temperature for changes of state, specifically for the change from gaseous to liquid and from liquid to solid state we have

gas                gas → liquid              liquid → solid

                         (ºC)                            (ºC)

H₂0 (Water)      100                                0

CO₂                 -56.6 (P> = 5.2 bar)     <-56.6

The temperature of the Titan satellite is - 180ºC

From the above, if these gases existed in Titan, this n in solid form, by which its absence in the atmosphere is understood.

three condensers are connected in series across a 150 volt supply, the voltages across them are 40,50 and 60 volts respectively, and the charge on each condenser is 6×10^-8 c.calculate (a) the capacitance of each condenser (b)the effective capacitance of the combination

Answers

Answer:

(a) 1.5 nF, 1.2 nF, 1 nF

(b) 0.4 nF

Explanation:

V = 150 V

V' = 40 V, V'' = 50 V, V''' = 60 V, q = 6 x 10^-8 C

(a) C' = q/V' = 6 x 10^-8 / 40  = 1.5 x 10^-9  F

C'' = q/V'' = 6 x 10^-8 / 50 = 1.2 x 10^-9 F

C''' = q/V''' = 6 x 10^-8 / 60 = 1 x 10^-9 F

(b) The effective capacitance is

[tex]\frac{1}{C}=\frac{1}{C'}+\frac{1}{C''}+\frac{1}{C'''}\\\\\frac{1}{C}=\frac{10^9}{1.5}+\frac{10^9}{1.2}+\frac{10^9}{1}\\\\C = 0.4\times 10^{-9} F[/tex]  

A hot-air balloon is rising upward with a constant speed of 2.85 m/s. When the balloon is 2.50 m above the ground, the balloonist accidentally drops a compass over the side of the balloon. How much time elapses before the compass hits the ground

Answers

Answer:

Explanation:

You have to declare which way is plus -- up or down. I will use down.

vi = - 2.85       The balloon is going up. That is the minus direction.

a = 9.81

d =   2.50 meters  distance in this case is from the object to the ground.

d = vi*t + 1/2 a t^2

-2.50 = -2.85*t + 1/2 * 9.81 * t^2

-2.50 = -2.85*t + 4.905 * t^2           transfer the left to the right.

-4.905 t^2 + 2.85*t + 2.50 = 0

Use the quadratic formula to solve for t.

It turns out that t = 1.06

A toy rabbit of mass 0.15 kg is accelerated at 8 m/s2 by an angry toddler. Calculate the force exerted on the toy rabbit.

Answers

Answer:

1.2 N

Explanation:

Given that,

Mass (m) = 0.15 kgAcceleration (a) = 8 m/s²

We are asked to calculate force exerted (F).

[tex]\longrightarrow[/tex] F = ma

[tex]\longrightarrow[/tex] F = (0.15 × 8) N

[tex]\longrightarrow[/tex] F = 1.2 N

A screw Jack whose pitch is 2mm is used to raise a bus of mass 900kg through height of 20cm. The length of the Tommy of the Tommy of the jack is 40cm. Calculate the velocity ratio of the machine

Answers

R= 40cm —> R= 0.4 m

P= 2mm —> P= 0.002 m

[tex]V.R = \frac{2πR}{p} = \frac{2 \times 3.14 \times 0.4}{0.002} = 1256[/tex]

I think this is the answer

I hope I helped you

Good luck ^_^

Put the steps of the scientific method in order

Answers

step 1, ask a question
step 2, do research
step 3, make a hypothesis
step 4, test your hypothesis with an experiment
step 5, analyze your data
step 6, make a conclusion
Other Questions
Driving on asphalt roads entails very little rolling resistance, so most of the energy of the engine goes to overcoming air resistance. But driving slowly in dry sand is another story. If a 1500 kg car is driven in sand at 4.9 m/s , the coefficient of rolling friction is 0.060. In this case, nearly all of the energy that the car uses to move goes to overcoming rolling friction, so you can ignore air drag in this problem.Required:a. What propulsion force is needed to keep the car moving forward at a constant speed? b. What power is required for propulsion at 5.0 m/s? c. If the car gets 15 mpg when driving on sand, what is the car's efficiency? One gasoline contains 1.410 ^8 J of chemical energy. TO SAVE TIME DOING RESEARCH PROCESS, DONT CHOOSE TOPICS THAT ARE TOO what do they reveal about Major kovaloffs charater what is meant by co-operation Find the value of x from the following given figures. The privately-owned school system in Smalltown has a virtually unlimited capacity. It accepts all applicants and operates on both tuition and private donations. Although every resident places value on having an educated community, the school's revenues have suffered lately due to a large decline in private donations from the elderly population. Since the benefit that each citizen receives from having an educated community is a public good, which of the following would not be correct? a. The free-rider problem causes the private market to undersupply education to the community b. The govemment can potentially help the market reach a socially optimal level of education. c. A tax increase to pay for education could potentially make the community better off. d. The private market is the best way to supply education. Which of these molecules are used for short term energy byorganisms?Select one:a. Proteinsb. Nucleic AcidsO c. Carbohydratesd. Lipids the red line below is perpendicular to which of the following Giving Brainliest Answer to whoever answers the questions!Knowing what you know about the topic, do you think that the Cold War is an appropriate name for the time period? Why? If you do not think it was appropriate, what do you think it should have been called? To carry out the Truman Doctrine, the United States adopted the policy of containment. Do you think it was a good foreign policy? Why/why not? Why would the United States want to help economically rebuild Europe? What's in it for us? Do you think someone like Senator Joseph McCarthy could have considerable power today? In the decision making process, identifying and weighing options as well as their risks and consequences is: implementing deciding evaluating deliberating Find a parametric representation for the surface. The plane through the origin that contains the vectors i - j and j - k Sobre la forma de vida de la gente en la Unin Sovitica durante el mandato de Stalin.porfa lo necesito para hoy Read an analysis of a theme in Hamlet.One theme in Hamlet is that the rules of society are often based on wealth and power rather than fairness.Which excerpt from Act V of Hamlet best provides evidence of the this themes development?A. Second Clown: I tell thee she is; and therefore make her grave straight: the crowner hath sat on her, and finds it Christian burial.B. First Clown: For here lies the point: if I drown myself wittingly it argues an act; and an act hath three branches; it is, to act, to do, and to perform: argal, she drowned herself wittingly. C. Second Clown: Will you ha the truth on t? If this had not been a gentlewoman she should have been buried out o Christian burial.D. First Clown: I like thy wit well, in good faith; the gallows does well, but how does it well? it does well to those that do ill; now thou dost ill to say the gallows is built stronger than the church: Y=2/7 -7 y=-x+2 What is the solution for this system of equations? Solve for x and y:x 3y = -83x + 2y = 31Select one:O a. (-11,-1)O b. (11,1)o c. (5,8)O d. (7,5) In the month of March, Wildhorse Salon services 620 clients at an average price of $130. During the month, fixed costs were $16,380 and variable costs were 70% of sales (a) Determine the total contribution margin in dollars, the per unit contribution margin, and the contribution margin ratio Contribution margin in dollars 5 Contribution margin per unit $ Contribution margin ratio % In female gamete development in humans and other vertebrates, the net result of meiosis is the production of one large egg and three small cells with very little cytoplasm. These three small cells? 4. How does financial resource affect the development of a country? The Molding Division of Cotwold Company manufactures a plastic casing used by the Assembly Division. This casing is also sold to external customers for $39 per unit. Variable costs for the casing are $12 per unit and fixed cost is $6 per unit. Cotwold executives would like for the Molding Division to transfer 22,000 units to the Assembly Division at a price of $33 per unit. Assume that the Molding Division has excess capacity, but the Assembly Division requires the casing to be made from a specific blend of plastics. This would raise the variable cost per unit to $37. 3 coins are flipped.