Answer:
7.46×10⁻⁶ m
Explanation:
Applying,
F = kqq'/r²............ Equation 1
make r the subject of the equation
r = √(F/kqq').......... Equation 2
From the question,
Given: F = 8 N, q' = q= 4 C
Constant: k = 8.98×10⁹ Nm²/C²
Substitute these values into equation 2
r = √[8/(4×4×8.98×10⁹)]
r = √(55.7×10⁻¹²)
r = 7.46×10⁻⁶ m
Find the current in the thin straight wire if the magnetic field strength is equal to 0.00005 T at distance 5 cm.
Answer:
Answer
Correct option is
A
5×10
−6
tesla
I=5A
x=0.2m
Magnetic field at a distance 0.2 m away from the wire.
B=
2πx
μ
0
I
=
2π×0.2
4π×10
−7
×5
=10×5×10
−7
=5×10
−6
tesla
A massless, hollow sphere of radius R is entirely filled with a fluid such that its density is p. This same hollow sphere is now compressed so that its radius is R/2, and then it is entirely filled with the same fluid as before. As such, what is the density of the compressed sphere?
a. 8p
b. p/8
c. p/4
d. 4p
Answer:
a. 8p
Explanation:
We are given that
Radius of hollow sphere , R1=R
Density of hollow sphere=[tex]\rho[/tex]
After compress
Radius of hollow sphere, R2=R/2
We have to find density of the compressed sphere.
We know that
[tex]Density=\frac{mass}{volume}[/tex]
[tex]Mass=Density\times volume=Constant[/tex]
Therefore,[tex]\rho_1 V_1=\rho_2V_2[/tex]
Volume of sphere=[tex]\frac{4}{3}\pi r^3[/tex]
Using the formula
[tex]\rho\times \frac{4}{3}\pi R^3=\rho_2\times \frac{4}{3}\pi (R/2)^3[/tex]
[tex]\rho R^3=\rho_2\times \frac{R^3}{8}[/tex]
[tex]\rho_2=8\rho[/tex]
Hence, the density of the compressed sphere=[tex]8\rho[/tex]
Option a is correct.
The table below describes some features of methods used to generate electricity. Name method 4.
Answer:
Hydroelectricity
Explanation:
Because of flooding of water, we can assume that the electricity was generated by Water which is known as Hydroelectricity.
We can presume that the energy was produced by water because of the flooding of the water, which is a process known as hydroelectricity.
What is hydroelectricity?Hydroelectric power, often known as hydropower, is the name given to electricity generated by turbines that turn the potential energy of falling or swiftly running water into mechanical energy. As of 2019, hydropower accounted for more than 18% of the world's total power generation capacity, giving it the most frequently used renewable power source in the early 21st century.
When water is used to produce energy, it is first gathered or stored at a higher altitude and then transported through extensive pipelines or tunnels (called pen stocks) to a lower level; the difference between these two altitudes is referred to as the head. The falling water triggers the rotation of turbines at the bottom of its descent through the pipes.
To know more about Hydroelectricity:
https://brainly.com/question/15228003
#SPJ2
Riley, a student, notices that the protractor tool does not measure the angle just as the ball leaves the surface. She sees that the ball must travel some distance before it crosses the protractor, so the direction of travel may have changed as the ball moves upwards. She says that this is the cause of the discrepancy between her predicted angle and the measured angle. Does this reasoning explain the discrepancy between your predicted angle and your measured angle. Use evidence to support your claim.
Answer:
Riley's reasoning is correct
Explanation:
Her reasoning is correct because as the ball moves upwards, the acceleration due to gravity would be vertical and in downward position. Therefore at all points as the ball moves, the velocity of the ball is going to change in magnitude as well as in direction. given that the direction keeps changing at certain points, the angle made by the initial velocity just as the ball left the surface would also have to continuously change.
If Riley has to wait for this ball to move some inches before she uses the protractor to measure the angle, the angle of travel would have to change.
Therefore there is going to be discrepancies between the measured angle and the predicted angle. The predicted is the angle of velocity with the horizontal just as this ball moves from the surface.
Question 3 of 10
Which statement describes the law of conservation of energy?
A. Air resistance has no effect on the energy of a system.
B. Energy cannot be created or destroyed.
C. The total energy in a system can only increase.
D. Energy cannot change forms.
هما
SUBMIT
Answer:
B . energy cannot be created or destroyed
Convierta 8.5mW a cal/h (1 cal=4.186 j)
Answer:
[tex] = { \bf{2.03 \times {10}^{ - 6} }}[/tex]
You simultaneously release two balls: one you throw horizontally, and the other you drop straight down. Which one will reach the ground first? Why?
(a) The ball dropped straight down lands first, since it travels a shorter distance.
(b) Neither. Their vertical motion is the same, so they will reach the ground at the same time.
(c) It depends on the mass of the balls—the heavier ball falls faster so lands first
Answer:
Option B.
Explanation:
Remember that we can think on any movement as a sum of a movement in the y-axis, the movement in the x-axis, and the movement in the z-axis. And these are not related, this means that, for example, the movement in x does not affect the movement in y.
So, when we analyze the problem of "how long takes an object to hit the ground"
We do not care for the horizontal motion of the object, we only care for the vertical motion of the object.
So, if an object is dropped, and another has a given initial velocity in the x-axis, in both cases the initial velocity in the y-axis will zero.
And in both cases, the only vertical force acting on the balls will be the gravitational force (so both objects will have the same vertical acceleration and the same vertical initial velocity) with this, we already know that the vertical motion of both objects will be exactly the same.
So, both objects will hit the ground at the same time.
(notice that here we are ignoring things like air resistance and other complex forces)
So here the correct option is b: Neither. Their vertical motion is the same, so they will reach the ground at the same time.
An ice chest at a beach party contains 12 cans of soda at 3.78 °C. Each can of soda has a mass of 0.35 kg and a specific heat capacity of 3800 J/(kg C°). Someone adds a 6.48-kg watermelon at 29.4 °C to the chest. The specific heat capacity of watermelon is nearly the same as that of water. Ignore the specific heat capacity of the chest and determine the final temperature T of the soda and watermelon in degrees Celsius.
Answer:
T = 13.25°C
Explanation:
From the law of conservation of energy:
Heat Lost by Watermelon = Heat Gained by Cans
[tex]m_wC_w\Delta T_w = m_cC_c\Delta T_c[/tex]
where,
[tex]m_w[/tex] = mass of watermelon = 6.48 kg
[tex]m_c[/tex] = mass of cans = (12)(0.35 kg) = 4.2 kg
[tex]C_w[/tex] = specific heat capacity of watermelon = 3800 J/kg.°C
[tex]C_c[/tex] = specific heat capacity of cans = 4200 J/kg.°C
[tex]\Delta T_w[/tex] = Change in Temprature of watermelon = 29.4°C - T
[tex]\Delta T_c[/tex] = Change in Temperature of cans = T - 3.78°C
T = final temperature = ?
Therefore,
[tex](4.2\ kg)(3800\ J/kg.^oC)(29.4^oC-T)=(6.48\ kg)(4200\ J/kg^oC)(T-3.78^oC)\\469224\ J-(15960\ J/^oC)T = (27216\ J/^oC)T-102876.48\ J\\469224\ J + 102876.48\ J = (27216\ J/^oC)T+(15960\ J/^oC)T\\\\T = \frac{572100.48\ J}{43176\ J/^oC}[/tex]
T = 13.25°C
A 10.0kg of desk initial is pushed along a frictionless surface by a constant horizontal of force magnitude 12N Find the speed of the desk after it has moved through a horizontal distance of 5.0m
kylydljty many true dvx*&;'*+$_5+
i.Name two commonly used thermometric liquids.
ii.State two advantages each of the thermometric liquids mentioned above
Answer:
mercury and alcohol
ii) used to test temperatures
i) It is a good conductor of heat and therefore the whole liquid reaches the temperature of the surroundings quickly.
ii) It does not wet (cling to the sides of) the tube.
Alcohol:
i) Alcohol has greater value of temperature coefficient of expansion than mercury.
ii) it's freezing point is below –100°C.
When the insulation resistance between a motor winding and the motor frame is tested, the value obtained is 1.0 megohm (106 Ω). How much current passes through the insulation of the motor if the test voltage is 1000 V?
Answer:
0.001 A
Explanation:
Applying,
V = IR.............. Equation 1
Where V = Voltage of the motor, I = current, R = resistance
make I the subject of the equation
I = V/R.............. Equation 2
From the question,
Given: V = 1000 V, R = 1 MΩ = 10⁶ Ω
Substitute these values into equation 2
I = 1000/10⁶
I = 10⁻³ A
I = 0.001 A
The electric potential ( relative to infinity ) due to a single point charge Q is 400 V at a point that is 0.6 m to the right of Q. The electric potential (relative to infinity) at a point that is 0.90 m to the left of 0 is:_____.
A. + 400 V.
B. -400 V.
C. + 200 V.
Answer:
The potential at a distance of 0.9 m is 266.67 V.
Explanation:
Charge = Q
Potential is 400 V at a distance 0.6 m .
Let the potential is V at a distance 0.9 m.
Use the formula of potential.
[tex]V = \frac{Kq}{r}\\\\\frac{V}{400}=\frac{0.6}{0.9}\\\\V = 266.67 V[/tex]
how much amount of heat energy is required to convert 5 kg of ice at - 5° c into 100°c steam?
Assuming no heat lost to the surrounding,
-5⁰C ice → 0⁰C ice
Specific heat capacity of ice = 2.0 x 10³ J/kg/⁰C
Q = mc∆θ
Q = 5(2.0 x 10³) x (0-(-5))
Q = 50000J
0⁰C ice → 0⁰C water
Specific latent heat of fusion of ice = 3.34 x 10⁵J/kg
Q = mLf
Q = 5(3.34 x 10⁵)
Q = 1670000J
0⁰C water → 100⁰C water
Specific heat capacity of water = 4.2 x 10³ J/kg/⁰C
Q = mc∆θ
Q = 5(4.2 x 10³) x (100-0)
Q = 2100000J
100⁰C water → 100⁰C steam
Specific latent heat of vaporization of water = 2.26 x 10⁶ J/kg
Q = mLv
Q = 5(2.26 x 10⁶)
Q = 11300000J
Total amount of heat required
= 50000 + 1670000 + 2100000 + 11300000
= 15120000J
Suppose a van de Graaff generator builds a negative static charge, and a grounded conductor is placed near enough to it so that a 7.0 mu C of negative charge arcs to the conductor. Calculate the number of electrons that are transferred.
Answer:
# _electron = 4.375 10¹³ electrons
Explanation:
In this exercise it is indicated that 7.1 μC is transferred, let's use a direct ratio or rule of three. If an electron has a charge of 1.6 10⁻¹⁹ C, how many electrons have a charge of 7.0 10⁻⁶ C
# _electron = 7.0 10⁻⁶ C (1 electron / 1.6 10⁻¹⁹ C)
# _electron = 4.375 10¹³ electrons
Why is the force of attraction between the Earth and ourselves so huge compared to the attraction between two apples?
Answer:
Answer in explanation
Explanation:
The force of attraction between two bodies is governed by Newton's Law of Gravitation:
[tex]F = \frac{Gm_1m_2}{r^2}[/tex]
where,
G = Universal Gravitational Constant
m₁ = mass of the first body
m₂ = mass of the second body
r = distance between the two bodies
F = Force
Hence, it is clear from the formula that the magnitude of the force is directly proportional to the product of the masses of the objects. So in the case of the earth and ourselves, the mass of the earth is very large in order of 10²⁴ kg. Due to this huge mass, the attraction between the earth and ourselves is so huge as compared to the attraction between two apples. Because the masses of the apple are very small in grams.
7. If a load of 300N is pulled along the inclined plane shown in the figure, answer the following. B 200 N 0.5m 2m 300 N А i. Calculate the VR and MA of the inclined plane. Calculate the input work and output work. ii.what efficiency of inclined plane?iv.what should be the length of inclined plane if same load has to be pulled with a50N effort for the same efficiency as above
Explanation:
700n I think friend .. if worng
now suppose that we have attached not just two springs in series, but N springs. Write an equation that expresses the effective spring constant of the combination using the spring constant of the original spring k and the number of springs N
Answer:
[tex]k_{eq} = \frac{k}{N}[/tex]
Explanation:
For this exercise let's use hooke's law
F = - k x
where x is the displacement from the equilibrium position.
x = [tex]- \frac{F}{k}[/tex]
if we have several springs in series, the total displacement is the sum of the displacement for each spring, F the external force applied to the springs
x_ {total} = ∑ x_i
we substitute
x_ {total} = ∑ -F / ki
F / k_ {eq} = -F [tex]\sum \frac{1}{k_i}[/tex]
[tex]\frac{1}{k_{eq}} = \frac{1}{k_i}[/tex] 1 / k_ {eq} = ∑ 1 / k_i
if all the springs are the same
k_i = k
[tex]\frac{1}{k_{eq}} = \frac{1}{k} \sum 1 \\[/tex]
[tex]\frac{1}{k_{eq} } = \frac{N}{k}[/tex]
[tex]k_{eq} = \frac{k}{N}[/tex]
what is the average velocity if the initial velocity is at rest and the final velocity is 16 m/s
Answer:
8m/s
Explanation:
Vavg= 16-0/2=8m/s
In the late 19th century, great interest was directed toward the study of electrical discharges in gases and the nature of so-called cathode rays. One remarkable series of experiments with cathode rays, conducted by J. J. Thomson around 1897, led to the discovery of the electron.
With the idea that cathode rays were charged particles, Thomson used a cathode-ray tube to measure the ratio of charge to mass, q/m, of these particles, repeating the measurements with different cathode materials and different residual gases in the tube.
Part A
What is the most significant conclusion that Thomson was able to draw from his measurements?
He found a different value of q/m for different cathode materials.
He found the same value of q/m for different cathode materials.
From measurements of q/m he was able to calculate the charge of an electron.
From measurements of q/m he was able to calculate the mass of an electron.
Part B
What is the distance Δy between the two points that you observe? Assume that the plates have length d, and use e and m for the charge and the mass of the electrons, respectively.
Express your answer in terms of e, m, d, v0, L, and E0.
Part C
Now imagine that you place your entire apparatus inside a region of magnetic field of magnitude B0 (Figure 2) . The magnetic field is perpendicular to E⃗ 0 and directed straight into the plane of the figure. You adjust the value of B0 so that no deflection is observed on the screen.
What is the speed v0 of the electrons in this case?
Express your answer in terms of E0 and B0.
Answer:
a) He found the same value of q/m for different cathode materials.
b) y = [tex]- \frac{e}{m}\ \frac{E_o v_o^2 }{2d^2}[/tex] , c) v = [tex]\frac{E_o}{B_o}[/tex]
Explanation:
In Thomson's experiments he was able to measure the deflection of the light beam under the effect of the magnetic field and with these results find the e / m relationship, which in all cases is the same, therefore the most important conclusion is that the value e E / m is constant for all materials.
b) In the part of the plates the electrons are accelerated by the electric field,
F = ma
- e E = m a
a = - (e/m) E₀
the distance traveled is
X axis
x = v₀ t
the separation of the plates is x = d
t = vo / d
Y axis
y = v_{oy} t + ½ to t²
y = ½ a t²
y = [tex]- \frac{e}{m}\ \frac{E_o v_o^2 }{2d^2}[/tex]
c) In this case there is a magnetic field B₀ and the electrons have no deflection
F = - e E + e v x B
if there is no deviation F = 0
e E = e v B
v = [tex]\frac{E_o}{B_o}[/tex]
1. What is the total distance the car moves until it stops?
a. 250 m
b. 450 m
c. 300 m
d. 600 m.
Preocupada com o aumento da tarifa na conta de luz, uma pessoa resolve economizar diminuindo o tempo de banho de 20 para 15 minutos. Seu chuveiro possui as seguintes especificações: 4200 W e 220V. Sabendo que o kWh custa R$0,30, a economia feita em 10 dias foi de aproximadamente
Answer:
The mount saved is $ 0.105.
Explanation:
Concerned about the increase in the electricity bill, a person decides to save by reducing bathing time from 20 to 15 minutes. Your shower has the following specifications: 4200 W and 220V. Knowing that the kWh costs R$0.30, the savings made in 10 days were approximately.
The electrical energy is given by
E = P x t
where, P is the electrical power and t is the time.
When he is using the shower for 20 minutes, the energy consumed is
E = 4200 x 20 x 60 = 5040,000 J = 1.4 kWh
When he is using the shower for 15 minutes, the energy consumed is
E' = 4200 x 15 x 60 = 3780000 J = 1.05 kWh
The difference in energy is
E'' = E - E' = 1.4 - 1.05 = 0.35 kWh
The money saved is
= 4 0.3 x 0.35 = $ 0.105
A loop of wire is in a magnetic field such that its axis is parallel with the field direction. Which of the following would result in an induced emf in the loop?
A. Moving the loop outside of the magnetic field region.
B. Change the diameter of the loop.
C. Change the magnitude of the magnetic field.
D. Spin the loop such that its axis does not consistently line up with the magnetic field direction.
Answer:
All the given options will result in an induced emf in the loop.
Explanation:
The induced emf in a conductor is directly proportional to the rate of change of flux.
[tex]emf = -\frac{d \phi}{dt} \\\\where;\\\\\phi \ is \ magnetic \ flux\\\\\phi = BA\ cos \theta[/tex]
where;
A is the area of the loop
B is the strength of the magnetic field
θ is the angle between the loop and the magnetic field
Considering option A, moving the loop outside the magnetic field will change the strength of the magnetic field and consequently result in an induced emf.
Considering option B, a change in diameter of the loop, will cause a change in the magnetic flux and in turn result in an induced emf.
Option C has a similar effect with option A, thus both will result in an induced emf.
Finally, considering option D, spinning the loop such that its axis does not consistently line up with the magnetic field direction will change the angle between the loop and the magnetic field. This effect will also result in an induced emf.
Therefore, all the given options will result in an induced emf in the loop.
It takes the elevator in a skyscraper 4.0 s to reach its cruising speed of 10 m/s. A 60 kg passenger gets aboard on the ground floor.
1. What is the passenger's apparent weight before the elevator starts moving?
2. What is the passenger's apparent weight whilethe elevator is speeding up?
3. What is the passenger's apparent weight afterthe elevator reaches its cruising speed?
Answer:
1. 588 N
2. 738 N
3. 588 N
Explanation:
time, t = 4 s
initial velocity, u = 0
final velocity, v = 10 m/s
mass, m= 60 kg
1.
Weight of passenger before starts
W =m g = 60 x 9.8 = 588 N
2.
When the elevator is speeding up
v = u + a t
10 = 0 + a x 4
a = 2.5 m/s2
Now the weight is
W' = m (a + g) = 60 (9.8 + 2.5) = 738 N
3.
When he reaches the cruising speed, the weight is
W = 588 N
Diffuse reflection occurs when parallel light waves strike which surface? a mirror a rippling fountain a polished silver plate a still pond
Answer: a rippling fountain
Explanation: diffuse reflection happens on rough surfaces, so using the process of elimination, that leaves us with b, a rippling fountain (I also just took this test I'm pretty sure I'm right)
For waves moving through the atmosphere at a constant velocity, higher frequency waves must have proportionally longer wavelengths.
a) true
b) false
Answer:
false.
Explanation:
We know that for a wave that moves with velocity V, with a wavelength λ, and a frequency f, we have the relation:
V = λ*f
So, if the velocity is constant and we increase the frequency to:
f' > f
we will have a new wavelength λ'
Such that:
V = f'*λ'
And V = f*λ
Then we have:
f'*λ' = f*λ
Solvinf for λ', we get:
λ' =(f/f')*λ
And because:
f' > f
then:
(f/f') < 1
Then:
λ' =(f/f')*λ < λ
So, if we increase the frequency, we need to decrease the wavelength.
So, for higher frequency waves, we must have proportionally shorter wavelengths.
Then we can conclude that the given statement:
"or waves moving through the atmosphere at a constant velocity, higher frequency waves must have proportionally longer wavelengths"
is false.
There are two beakers of water on the table. We can compare the average kinetic energy of the water molecules in the two beakers by measuring their
A temperatures.
B volumes.
C densities.
D masses.
Answer: masses
Explanation:
Trust me
After de Broglie proposed the wave nature of matter, Davisson and Germer demonstrated the wavelike behavior of electrons by observing an interference pattern from electrons scattering off what
Answer:
Scattering is an interaction that can happen when a given particle or wave, like an electron, impacts a target or material. Then the electron changes it's original path and leaves some energy in the process. (This is a really simplified explanation of scattering, this is a really complex phenomenon, but let's not dive into that path)
Particularly, Davisson and Germer used a beam of electrons against a target of nickel, and these scattered electrons were detected by a detector. All of that in a vacuum chamber.
Then the correct answer is a nickel target.
"After de Broglie proposed the wave nature of matter, Davisson and Germer demonstrated the wavelike behavior of electrons by observing an interference pattern from electrons scattering off a nickel target"
Distillation is the separation of multiple Choose... components based on their different Choose... . As the mixture is heated and the first component Choose... , its Choose... form travels through the distillation set-up and Choose... into a different container.
Answer:
Explanation:
Distillation is the separation of multiple LIQUID components based on their different BOILING POINT. As the mixture is heated and the first component SEPARATES, its PURE form travels through the distillation set-up and GOES into a different container
Write submultipels units of time
What
is the the improvetanse of water in our body and how do
Or
open Meet and enter this code
Answer:
Or open Meet and enter this code to the source of definition and how to use it to make
Think about a thermos bottle. It consists of an inner bottle with a shiny silver surface separated from an outer container by a space with no air. In what ways does it block conduction, convection, and radiation?
Answer:
Radiation
Explanation:
Conduction, convection and radiation are the three modes of heat transfer.
1. Conduction: When the one end is heated of any rod, the heat transfer to the other end by the vibrational motion of the molecules, it is called conduction.
The heat transfer in a solid is due to the conduction.
2. Convection: When the liquid or gas is heated, the molecules which is in contact to the heat, heated first and due to the decrease in density they moves up and the molecules on the upper side are higher in density so they moves down. These are called convection currents. The process continues till the entire liquid becomes heated. It generally takes place in liquids and gases.
3. Radiation: The process of heat transfer in which no molecules takes place is called radiation. The heat coming from sun is due to the radiation. It does not require any medium.
In the thermos bottle, as there is no air between the two layers, so the heat transfer is due to the radiation.