A) The answer to whether an average-size, single-family home be built with one day’s output from the saw mill is; No, it can't be built from one days output
B) The number of days will it take for the saw mill to produce enough lumber to build a neighborhood of 100 average-size homes is; 1100 days
A) From research, the average size capacity saw mill usually produces around 1500 board feet of boards per day.
Now, converting board ft to cubic meter gives;
1 board feet = 1/424 m³
Thus; 1500 board feet = 1500 * 1/424 ≈ 3.54 m³
Now, we are told that it takes 38 m³ of boards and plywood to build an average size single family home.
Since one days output = 3.54 m³
It is less than the volume required for the average sized house and so the daily output will not be sufficient.
B) Number of days to produce enough boards and plywood for the average sized family home = 38/3.54 ≈ 11 days
Thus, for 100 homes;
Number of days = 100 * 11 = 1100 days
Read more about production capacity at; https://brainly.com/question/25899399
Read the statement. Magnesium atoms have 12 electrons, with the configuration 2-8-2. If the first five ionization energies of magnesium are shown, which ionization energy would show a sudden sharp increase?
The electronic configuration of magnesium is:
1s² 2s² 2p⁶ 3s² = [Ne] 3s²
This means that for a magnesium atom, in order to have its outermost orbital full, the easiest way would be to lose the two outermost electrons. This is seen in its relatively low first two ionization energies. The third ionization energy is several times higher because the ion would move from a stable form to an highly unstable form. (Mg⁺² → Mg⁺³ + e⁻).
Sodium only has one electron in its outermost orbital, so its first ionization energy would be several times lower than the second.
? Which types of batteries are commonly used in laboratory equipments
Answer:
your question is not very clear but I think the answer is either
Primary (non-rechargeable)
Secondary (rechargeable) or
Lithium-ion battery.
Rechargeable li-ion button cell.
Tyra designed an experiment to demonstrate an annular solar eclipse. The steps of the
experiment are listed below.
.
e
.
Place a light bulb on a stand.
Stick a pencil into a small styrofoam ball.
Switch on the light bulb and darken the room.
Stand facing the light bulb.
Hold the pencil with styrofoam ball very close to the eye.
Observe the light bulb without moving the eye and styrofoam ball.
Tyra's experiment has a flaw. Which of these statements best describes a method to
correct the flaw in Tyra's experiment? (3 points)
.
.
Place the light bulb behind the observer.
O Clamp the styrofoam ball behind the light bulb.
O Move eye towards the right to observe the light bulb.
Hold the styrofoam ball at arm's length from the eye.
Answer:
The answer is D.
Explanation:
Hold the styrofoam ball at arm's length from the eye.
Can I get some help
Answer:
I'm afraid not, the image is too blurry
yesss☺️
sorryyyyyy
sorryyyyy
The F-C-F bond angle in the CH2F2 molecule is approximately __________.
Group of answer choices
180°
90°
120°
60°
109.5°
Answer:
109.5°
Explanation:
Pls Cross Check It, If It Correct
What is the most soluble in water? iconic, covalent, metallic or nonmetallic
How are the sensory clues from watching a fire different from the sensory clues from watching a firefly?
Answer:
sensory experience of a chemical reaction called combustion. In a way, fire is like the leaves changing color in fall, the smell of fruit as it ripens, or a firefly's blinking light. All of these are sensory clues that a chemical reaction is taking place
Explanation:
Sensory encounter with the combustion chemical process. Fire can be compared to the fall foliage's shifting hues, the aroma of ripe fruit, or the blinking light of fireflies. These are all sensory indicators that a chemical reaction is occurring.
What is combustion?Combustion is defined as a chemical interaction between different compounds, usually involving oxygen, that produces heat and light in the form of flames. Hydrocarbons and oxygen are the only reactants in a combustion reaction. The fuel is a hydrocarbon, and oxygen is required for burning.
It stimulates several of our senses at once, producing the vivid experience we anticipate from a tangible object. By using fuel, heat, and oxygen during combustion, that sensory experience is produced.
Thus, sensory encounter with the combustion chemical process. Fire can be compared to the fall foliage's shifting hues, the aroma of ripe fruit, or the blinking light of fireflies. These are all sensory indicators that a chemical reaction is occurring.
To learn more about combustion, refer to the link below:
https://brainly.com/question/15117038
#SPJ2
Please help due tomorrow
Answer:
The gravitational force at the center of the Earth is 0.
Please help due tomorrow
Giving Brainlesst
Answer:
Down arrow:
-a car comes to a stop when a traffic light turns red
Up arrow:
-race car accelerates when a race begins
Circle:
-car driving 45 mile per hour down straight road
Explanation:
and i think the car going around a bend would be an up arrow
What is the name of the compound K3N
A chemical compound is a material made up of several types of molecules. Therefore, potassium Nitride is the name of the compound K[tex]_3[/tex]N.
What is chemical compound?A compound is indeed a substance that is composed of two or more separate chemical elements mixed in a defined ratio in chemistry. When the elements combine, they react and generate chemical connections that really are hard to break. These bonds occur as a result of atoms sharing or exchanging electrons.
A chemical compound is a material made up of several types of molecules (or molecular entities) that include atoms from much more than one chemical element and are bound together by chemical bonds. Potassium Nitride is the name of the compound K[tex]_3[/tex]N.
Therefore, potassium Nitride is the name of the compound K[tex]_3[/tex]N.
To learn more about chemical compound, here:
https://brainly.com/question/26487468
#SPJ5
Answer ASAP pls
The electromagnetic spectrum is the portion of energy that reaches the Earth from the Sun. However, the human eye can still only detect a portion of that spectrum because of the _____________ of the visible light waves.
wavelengths
troughs
crests
amplitude
Answer:
wavelengths
Explanation:
Which charge does iron (Fe) have in iron sulfate (FeSO4)?
A) -1
B) +2
C) -2
D)+2
The charge on iron (Fe) in iron sulfate (FeSO₄) is equal to +2. Therefore, option (D) is correct.
What are the ionic charges?The ionic charge can be described as the oxidation number of the chemical species. The cation carries a positive ionic charge while Anion carries a negative ionic charge. The number of electrons gained or lost by an atom decides the charge carried by ions.
In the modern periodic table, the elements placed on the left side are electropositive and act as metals because they can donate one or more electrons. The elements placed on the right side are electronegative as they can accept one or more electrons and get a negative charge on their ions.
Considering that the charge on the iron is x, We know that charge on the sulfate ion is -2.
x - 2 = 0
x = +2
Therefore, the charge on iron (Fe) in iron sulfate (FeSO₄) is +2.
Learn more about ionic charge, here:
brainly.com/question/13581109
#SPJ2
Heart, 5 stars, and Brainiest to first right answer!
(Explanation problem) Can you list two ways in which the biosphere would be impacted if there were no hydrosphere.
Answer:
Without the hydrosphere, the atmosphere will no longer be able to carry up the evaporated water, as well as pour down the water, leaving the biosphere to rot away. The hydrosphere works with the Biosphere to provide the requirement of water to the organisms needs, as well as the hydrosphere assisting in photosnythesis.
Explanation:
Answer:
The hydrosphere refers to the water on the earth crust. If there were no hydrosphere, we would not have lakes, oceans, rivers, or even a hose full of water. There would also be no life. Nothing can live without water, so nothing would have evolved.
Explanation:
Drawing and dialogue please help due tomorrow
Answer:
Gravity will always be pulling everything towards Earth's center at an acceleration of 9.81 m/sec².
help!!!! the relative formula mass (Mr) of sodium fluoride is 42. Use the correct answer frim the box to complete the sentence.
Answer:
mole
Explanation:
Since Sodium Chloride is ionic, it cannot be considered a molecule as per the definition of a molecule requires each of its components to be bonded together.
The formula mass of a compound is the mass of its one molecule. Since molecule is the basic unit of a compound. Thus, the relative formula mass in grams is the mass of one molecule.
What is sodium fluoride?Sodium fluoride is an ionic compound formed by the combination of sodium and fluorine by loss of one electron from sodium to fluorine. The formula mass of fluorine is calculated from the atomic masses of sodium and fluorine.
Atomic mass of fluorine is 19 g/mol and mass of sodium is 23 g/mol. Here only one sodium and one fluorine is present. Hence the formula mass is 23+ 19 = 42.
This is the mass of one unit of NaF. Thus mass of one sodium fluoride molecule. Where as its molar mass may differ from the formula mass. Since the molar mass is the mass of one mole of the compound NaF. One mole of compound contains 6.02 × 10²³ molecules.
To refer more on formula mass, find the link:
https://brainly.com/question/28647347
#SPJ2
Triple covalent bond can be formed between:
a)C&H
b) N&S
c) C & S
d) C&O
e) O & S
true or false in a chemical reaction the same number of each type of atom will always be present before and after the reaction takes place
Answer:
True
Explanation:
True because of the law of conservation of mass, the same same amount of atoms will be on both sides of the reaction.
9.23 x 10^23 Au atoms= moles Au
Answer:
1.533 moles Au
Explanation:
To find the moles from atoms, you just use Avogadro's number (6.02214076×10^23 mol^-1) and divide by it. Hope this helped!
Answer:
[tex]\boxed {\boxed {\sf 1.53 \ mol \ Au}}[/tex]
Explanation:
We are asked to find how many moles of gold are in 9.23 *10²³ atoms of gold.
Avogadro's Number or 6.022 *10²³ is used to convert atoms to moles. This is the number of particles (atoms, molecules, formula units, etc.) in 1 mole of a substance. In this case, the particles are atoms of gold.
We convert using dimensional analysis. Set up a conversion factor using Avogadro's Number.
[tex]\frac {6.022 \times 10^{23} \ atoms \ Au}{ 1 \ mol \ Au}[/tex]
We are converting 9.23 * 10²³ atoms of gold to moles, so we multiply by this value.
[tex]9.23 \times 10^{23} \ atoms \ Au *\frac {6.022 \times 10^{23} \ atoms \ Au}{ 1 \ mol \ Au}[/tex]
Flip the conversion factor so the units of atoms of gold cancel.
[tex]9.23 \times 10^{23} \ atoms \ Au *\frac { 1 \ mol \ Au}{6.022 \times 10^{23} \ atoms \ Au}[/tex]
[tex]9.23 \times 10^{23} *\frac { 1 \ mol \ Au}{6.022 \times 10^{23}}[/tex]
[tex]\frac {9.23 \times 10^{23} }{6.022 \times 10^{23} } \ mol \ Au[/tex]
[tex]1.53271338426 \ mol \ Au[/tex]
The original measurement of atoms has 3 significant figures, so our answer must have the same. For the number we found, that is the hundredth place. The 2 in the thousandth place tells us to leave the 3.
[tex]1.53 \ mol \ Au[/tex]
9.23 *10²³ atoms of gold is equal to approximately 1.53 moles of gold.
CH3-C_=CH + HCl ( 1:2) -->
You have 58 g of calcium chloride (CaCl2) and you need to make a 5 M solution. You know that the molecular weight of Ca is 40 and that the molecular weight of Cl is 35.5. How many liters (L) of water would you need
Answer:
0.1045 L (4 s.f.)
Explanation:
The molecular weight, [tex]M_{r}[/tex], of calcium chloride is
[tex]M_{r}(\mathrm{CaCl_{2}}) \ = \ A_{r}(\mathrm{Ca}) \ + \ 2 \times A_{r}(\mathrm{Cl}) \ = \ (40 \ + \ 2 \times 35.5) \ \mathrm{g \ mol^{-1}} \ = \ 111 \ \mathrm{g \ mol^{-1}}[/tex], where [tex]A_{r}[/tex] is the atomic weight of the respective elements.
To calculate the number of moles (n) of calcium chloride present in 58g,
[tex]n_{\mathrm{CaCl_{2}}} \ = \ mass \ \div \ molecular \ weight \ (M_{r}) \\ \\ \-\hspace{1.13cm} = \ 58g \ \div \ 111 \ \mathrm{g \ mol^{-1}} \\ \\ \-\hspace{1.13cm} = \ 0.5225 \ \mathrm{mol \ of \ CaCl_{2}}[/tex]
Since molarity, M, is defined as the number of moles (n) of the solute per liters of a solution (L), hence to get the volume (V) required to make up a 5 molar solution is
[tex]n \ = \ M \times V \\ \\ V \-\hspace{0.05cm} = \ \displaystyle\frac{n}{M} \\ \\ V \-\hspace{0.05cm} = \displaystyle \frac{0.5225 \ \mathrm{mol}}{5 \ \mathrm{mol \ L^{-1}}} \\ \\ V \-\hspace{0.05cm} = \ 0.1045 \ \mathrm{L}[/tex]
Safety considerations
• Sodium Hydroxide (please insert one statement of caution from MSDS)
Answer:
d took the test
Explanation:
What is the balanced form of the chemical equation shown below?
N2(g) + H2(9) ► NH3(9)
O A. N2(9) + H2(9) ► NH3(9)
B. N2(9) + H2(g) → 2NH3(9)
)
O C. N2(g) + 3H2(g) → 2NH3(9)
O 9
D. N2(9) + H2(g) → 2NH(9)
Answer:
C
Explanation:
2 N on left so we put a 2 on the right which makes 6 H so we need 6H on the left to do that we add a coef. of 3 to make 6 H and balance the equation
Draw the Lewis structures for
Calcium bromide, CaBr2
The Lewis structure is the way of expressing the covalent bonding in molecules. The covalent bond formation takes place by the sharing of electrons in a molecule.
What is Lewis structure?In Lewis dot structures or simply the Lewis structures, the dots are used to represent the electrons. They provide a picture of bonding in molecules in terms of the shared pair of electrons and the octet rule.
The concept of covalent bond is introduced by the scientist G.N Lewis. According to him, the atoms achieve stable octet when they are linked with each other by sharing of one more pairs of electrons. The covalent bonding occurs between the atoms which do not differ much in their electronegativity.
The Lewis structure of CaBr₂ is denoted below. Here two bromine atoms acquires a stable electronic configuration by sharing electrons. There are two single bonds between them.
To know more about Lewis structure, visit;
https://brainly.com/question/20300458
#SPJ5
Which of the following is considered to be matter?
O A. Water
O B. Facts
O C. Energy
D. Theories
bcz the defination of matter is that
anything which occupy space
water can occupy space so it is matterfact :something that you know has happened or is true which doesn't occupy any space so this option is falseenergy : energy is the quantitative property that must be transferred to a body or physical system to perform work on the body, or to heat it. it doesn't occupy any space so this option is falseA theory is a well-substantiated explanation of an aspect of the natural world that can incorporate laws, hypotheses and facts.--it doesn't occupy any space so this option is falseHence , option a is correct
It takes 120 mL of 0.15 M of carbonic acid (H2CO3) to neutralize 300 mL of sodium hydroxide (NaOH) for the following balanced chemical reaction:
2NaOH + H2CO3 → N2CO3 + 2NaOH
The concentration of the sodium hydroxide _____.
0.03 M
0.24 M
0.12 M
0.06 M
If there is .03L of NaOH in a flask, how can a .12M solution of H2SO4 be used to determine the concentration of NaOH in the reaction?
The concentration of NaOH in the reaction can be determined using the Titration method.
The concentration of NaOH in the reaction can be determined by titration.
A burette if filled with the known concentration of H₂SO₄ and then titrated against the known volume of NaOH in a conical flask. An indicator is used in order to determine the end-point of the titration process. At the end-point of the titration, the volume of acid used is recorded.
Next, we will write the balanced chemical equation of the reaction.
The balanced chemical equation for the reaction is
2NaOH + H₂SO₄ → Na₂SO₄ + 2H₂O
This means 2 moles of NaOH is required to neutralize 1 mole of H₂SO₄
Now, we can determine the concentration of NaOH by using the titration formula.
[tex]\frac{C_{A}V_{A} }{C_{B}V_{B}} = \frac{n_{A}}{n_{B}}[/tex]
Where [tex]C_{A}[/tex] is the concentration of acid
[tex]V_{A}[/tex] is the volume of acid
[tex]C_{B}[/tex] is the concentration of base
[tex]V_{B}[/tex] is the volume of base
[tex]n_{A}[/tex] is the mole ratio of acid
[tex]n_{B}[/tex] is the mole ratio of base
Then, we put the respective parameters, including the volume of acid determined from the titration process, into the formula to determine the concentration of the NaOH.
Hence, the concentration of NaOH in the reaction can be determined using the Titration method.
Learn more on titration here: https://brainly.com/question/25290615
determine the gram-formula mass of stearin acid C17H35COOH
Answer:
284.48 g/mol
Explanation:
You can find the molar mass of any molecule by looking at a periodic table and adding up all of the masses of each element. When you do this with stearic acid, you get somewhere around 284.5 g/mol. Hope this helped!
what is oxidation number on Ni in the next compound
K2[NiBr6] ???
Explanation:
The oxidation number of Ni is +4
Hello do anyone on here no something about Gizmos Fan Cart Physics?
Answer:
yes here is the answer key
for the last question it is a challenge question, here is the answer:
(A) The mass of the cart is 1.214 kg
(B) The mass of one fan is 1.262 kg
(C) The mass of one of the draggable mass units is 3.131 kg
Explanation:
When Zinc-67 is bombarded with a neutron, a gamma ray is emitted. What radioactive isotope is produced?
Answer:16/29
Explanation: