five coulombs (5 c) of charge pass through the element from point a to point b. if the energy absorbed by the element is 120 j, determine the voltage across the element.

Answers

Answer 1

The voltage across the element is 24 V where if the energy absorbed by the element is 120 j.

Given data as per the question:

Charges = 5 coulomb

Energy absorbed by the element = 120 J

As per the formula we have,

Energy = Voltage X Charge

120= Voltage X 5

Voltage = 120/5 = 24 V

The voltage in the whole process will be negative because the energy is absorbed.

In a series circuit, the current is the same for all the components. While the circuit reaches its steady state, the capacitor charges and the voltage across its plates increases until it reaches the one on the terminals, and at that point it is in the steady state.

Learn more about Voltage:

brainly.com/question/12017821

#SPJ4

Answer 2

If the energy absorbed by the element is 120 j, So 5*V1 =120 , V1 =24 Volts.

The voltage distinction be V1 Volts.

When 5C of charge moves from A to B, its energy increments by 120J.

So 5*V1 =120

V1 =24 Volts.

The voltage distinction is hence 24 Volts.

At the point when the charge moves from higher potential to lower, it loses energy and when it moves from lower potential to higher, it retains energy. The energy ingested (or lost) is relative to the potential (voltage) contrast between the two focuses.

The voltage in the entire cycle will be negative in light of the fact that the energy is retained.

In a series circuit, the current is no different for every one of the parts. While the circuit arrives at its consistent express, the capacitor charges and the voltage across its plates increments until it arrives at the one on the terminals, and by then it is in the consistent state.

to know more about voltage click here:

https://brainly.com/question/1176850

#SPJ4


Related Questions

a - ladder leans against the side of a house. the bottom of the ladder is from the side of the house. how high is the top of the ladder from the ground? if necessary, round your answer to the nearest tenth.

Answers

The top of the 12 ft ladder that leans against the house, and the bottom of the ladder is 9 ft from the side of the house = 7.9 ft

The triangle formed by the ladder must be a right angle with a hypotenuse (Side opposite to right angle) of 12 feet since the side of the house must be vertical to the ground to form a right angle.

Let x represent how high the ladder's top is above the ground.

We have the following using the Pythagoras theorem of right triangles:

c² = a² + b²

12² = 9² + x²

x² = 144 - 81

= 63

Hence,

x = √63

= 7.9 ft

The question is incomplete, it should be:

A 12 - ft ladder leans against the side of a house. the bottom of the ladder is 9 ft from the side of the house. how high is the top of the ladder from the ground? if necessary, round your answer to the nearest tenth.

Learn more about Pythagorean theorem here: https://brainly.com/question/343682

#SPJ4

20° An 80 kg acrobat rests at top of a frictionless cannon angled at 20 degrees above the horizontal. A 20 kg cannonball is fired as shown. Upon reaching the acrobat, the ball is moving at 50 m/s just before colliding. The ball and acrobat stick together and soar through the air landing on a trampoline at the same height that the projectiles left the cannon at. Determine the following: a) The time in the air b) The range from when the objects leave the cannon c) The maximum height measured from where the projectiles leaves the cannon m m

Answers

The maximum height reached is approximately 101 meters above the ground.

Using this equation, we can solve for the time in the air, which turns out to be approximately 4.06 seconds. To find the range of the objects, we can use the horizontal component of the velocity of the cannonball, which is given by :

[tex]v = v 0 cos(theta),[/tex]

where v0 is the initial velocity of the cannonball and theta is the angle of elevation. We can use the equation of motion for the vertical component of the motion, which is given by:

[tex]height = v0y * t + (1/2) * g * t^2,[/tex]

where v0y is the initial vertical velocity and g is the acceleration due to gravity.

To know more about  initial vertical velocity, here

https://brainly.com/question/18965435

#SPJ4

Adam lifts a book from the floor, carries it across the room, and places it on a high shelf. When is Adam doing work on the book?

W= FD
Work = Force x Distance

A. He does work from the moment he touches the book until he lets it go.
B. He does work only while he carries the book across the room.
C. He does work on the book at no time during this process.
D. He does work as he picks up the book and as he lifts it to the shelf.

Answers

Adam lifts a book from the floor, carries it across the room, and places it on a high shelf, he does work only while he carries the book across the room, which is in option B, as work = force x distance.

What is the work done by a person?

According to the equation for work (W = FD), work is only done when a force is applied to an object and it moves some distance as a result of that force, when Adam lifts the book from the floor, he applies force to it, but the book does not move any distance, so no work is done when the object doesn't move, but when he moved the book, work was done.

Hence, he does work only while he carries the book across the room, which is in option B, as he lifts a book from the floor and carries it across the room.

Learn more about the work done by a person here.

https://brainly.com/question/16805476

#SPJ1

Which of the following actions will increase the electric field strength at the position of the dot? - Make the rod longer without changing the charge. - Make the rod shorter without changing the charge. - Make the rod fatter without changing the charge.- Make the rod narrower without changing the charge. - Remove charge from the rod

Answers

E: "Removing charge from the rod" will increase the electric field strength at the position of the dot.

The electric field strength at the position of the dot depends on the charge and the distance from the charge. Therefore, any change that affects the charge or the distance will also affect the electric field strength.

A and B - Changing the length of the rod without changing the charge does not affect the charge density, and thus does not affect the electric field strength at the position of the dot. Therefore, options A and B are not correct.C and D - Changing the cross-sectional area of the rod without changing the charge does affect the charge density, and therefore can affect the electric field strength at the position of the dot. However, it is not clear how changing the rod's shape will affect the charge density, and so it is not possible to determine whether option C or D will increase or decrease the electric field strength. Therefore, options C and D are not correct.E - Removing charge from the rod will decrease the charge, and therefore decrease the electric field strength at the position of the dot. Therefore, option E is correct.

You can learn more about electric field strength at

https://brainly.com/question/1216683

#SPJ4

Help!!
A horse does 860 J of work in 420 seconds while pulling a wagon. What is the power output of the horse? Round your answer to the nearest whole number.
The power output of the horse is [???] W.

Answers

To find the power output of the horse, we can use the formula:

power = work / time

We are given that the horse does 860 J of work in 420 seconds. Substituting these values into the formula, we get:

power = 860 J / 420 s

Dividing 860 by 420, we get:

power = 2.047619...

Rounding this to the nearest whole number, we get:

power = 2 W

So the power output of the horse is 2 watts.

Find the marginal cost functions for each of the following average cost functions. a) AC= 1.5Q + 4 + 460 b) AC = 160 +5+3Q+2Q²

Answers

(a) The marginal cost function is MC = 3Q + 464.

(b) The marginal cost function is MC = 160 + 5 + 6Q + 6Q^2.

What is the marginal cost function?

The marginal cost (MC) of a product is the change in the total cost of producing an additional unit of the product.

(a) AC = 1.5Q + 4 + 460

The total cost (TC) of producing Q units is given by:

TC = AC * Q

TC = (1.5Q + 4 + 460) * Q

TC = 1.5Q^2 + 4Q + 460Q

TC = 1.5Q^2 + 464Q + 460

The marginal cost function is given by the derivative of the total cost function with respect to Q:

MC = dTC/dQ

MC = d/dQ (1.5Q^2 + 464Q + 460)

MC = 3Q + 464

b) AC = 160 + 5 + 3Q + 2Q²

The total cost of producing Q units is given by:

TC = AC * Q

TC = (160 + 5 + 3Q + 2Q^2) * Q

TC = 160Q + 5Q + 3Q^2 + 2Q^3

The marginal cost function is given by the derivative of the total cost function with respect to Q:

MC = dTC/dQ

MC = d/dQ (160Q + 5Q + 3Q^2 + 2Q^3)

MC = 160 + 5 + 6Q + 6Q^2.

Learn more about marginal cost here: https://brainly.com/question/17230008

#SPJ1

use your function to predict the force on the force sensor when the ramp angle is 90 degrees. to make your prediction, assume a cart mass of 2.25 kg.

Answers

When the angle is 90 degrees up, the only force acting in a downward direction is gravitational force, with magnitude mg, where m is mass and g is gravitational acceleration.

m = 2.25 kg, g = 9.8 /s²

F = mg = 2.25 × 9.8

F = 22.05 N.

An item falling freely in a vacuum is said to accelerate gravitationally in physics. This is the constant acceleration brought on just by the gravitational pull.

By putting an object in a vacuum chamber and monitoring the object's speed as a function of time as it accelerates, one can calculate the gravitational acceleration. This is the approach that Galileo popularized.

Learn more about gravitational acceleration here brainly.com/question/14374981

#SPJ4

show that for every k, there is a set of k positive integers such that the difference of any two of these has an even number of prime factors, counted with multiplicity. (hint: you don't need to know any number theory.)

Answers

It is demonstrated that for each k, there exists a set of k positive integers whose difference has an even number of prime components, counted with multiplicity.

Let's construct the set of positive integers using the following algorithm:

Start with the first k prime numbers: 2, 3, 5, 7, 11, ..., p_k.

Define the i-th integer in the set as the product of the first i prime numbers: a_i = 235*...*p_i.

Claim: For any two integers in the set, their difference has an even number of prime factors, counted with multiplicity.

Proof:

Let a_i and a_j be two integers in the set such that i < j. We want to show that the difference a_j - a_i has an even number of prime factors, counted with multiplicity.

Notice that a_j - a_i can be written as:

a_j - a_i = 235*...p_i(235*...*p_j/2 - 1)

The first term on the right-hand side has i prime factors, and the second term has an odd number of prime factors. To see why the second term has an odd number of prime factors, notice that all the prime factors of 235*...p_j are also prime factors of 235...*p_i, so they cancel out in the difference.

a_j - a_i has i prime factors plus an odd number of prime factors, which is an even number of prime factors. This completes the proof.

For more such questions on  positive integer

https://brainly.com/question/13752294

#SPJ4                                              

Calculate whether the kinetic energy of the particle increase, decrease or remain the same if the particle`s velocity changes (a) from -3 m/s to -2 m/s and (b) from -2 m/s to 2 m/s if the particle moves along x axis.? (c) In each situation, is the work done on the particle positive, negative or zero?

Answers

Answer:

(a) The kinetic energy of the particle will decrease if the particle's velocity changes from -3 m/s to -2 m/s.

(b) The kinetic energy of the particle will increase if the particle's velocity changes from -2 m/s to 2 m/s.

(c) The work done on the particle in both situations is positive. This is because work is the energy transferred to or from a system and the kinetic energy of the particle increases in both cases, indicating energy was transferred to the particle.

Which is an example of kinetic energy being used?(1 point)

Answers

Answer:

A person walking, a soaring baseball, a crumb falling from a table and a charged particle in an electric field are all examples of kinetic energy at work.

Explanation:

Walking and running. Cycling. In a windmill, when the moving air hits the blades, it causes rotation which ultimately leads to the generation of electricity. In a hydropower plant, when the kinetic energy of the moving water hits the turbine the kinetic energy of the water gets converted to mechanical energy.

How can a spacecraft reduce its speed during a trip to Mars?
Answer options with 4 options
A.
eliminate all forces acting on the spacecraft
B.
fire rockets to increase force acting in the direction of travel
C.
fire reverse rockets to increase force acting opposite of the direction of travel
D.
open a parachute to increase force acting opposite to the direction of motion of the spacecraft

Answers

A spacecraft can reduce its speed during a trip to Mars by firing reverse rockets to increase force acting opposite of the direction of travel.

option C.

How can a spacecraft reduce its speed?

To reduce the speed of a spacecraft during a trip to Mars, the most common method is to fire reverse rockets, also known as braking thrusters.

These thrusters are used to generate a force that acts in the opposite direction of the spacecraft's motion, slowing it down. This is called a deceleration burn, and it is an important step in the process of entering into orbit around a planet or landing on its surface.

The reverse thrust slows down the spacecraft, reducing its speed and allowing it to be captured by the planet's gravity. This is crucial for the success of the mission and ensures that the spacecraft can be safely guided into orbit or landed on the surface of the planet.

Learn more about speed of spacecraft here: https://brainly.com/question/29727760

#SPJ1

If a graded receptor potential made the resting membrane potential of the axon more negative (for example, -70 mV changes to 75 m), you would expect A. it to be easier for this axon to reach the threshold voltage. B. subsequent action potentials to be shorter in duration C. no change in the ability of this axon to reach threshold voltage. D. it to be more difficult for this axon to reach the threshold voltage.

Answers

If a graded receptor potential made the resting membrane potential of the axon more negative (for example, -70 mV changes to 75 m), it would be more difficult for this axon to reach the threshold voltage (option D)

The resting membrane potential will become less negative as the extracellular K+ concentration rises.

Because the negative charge inside the cell exceeds the positive charge outside, the resting membrane potential is negative.

The distinction between the inside and outside of the cell is lessened as a result.

The resting membrane potential would be impacted by a change in Na+ or K+ conductance.

Since the membrane is more permeable to K+, a change in K+ conductance would have a bigger impact on resting membrane potential than a change in Na+ conductance.

Learn more about membrane potential here: https://brainly.com/question/30433151

#SPJ4

A hot rod can accelerate from 0 to 60 km/h in 7.5 s. (a) What is its average acceleration, in m/s2, during this time? (b) How far will it travel during the 7.5 s, assuming its acceleration is constant? (c) From rest, how much time would it require to go a distance of 0.40 km if its acceleration could be maintained at the value in (a)?

Answers

Average acceleration is a) 2.22 [tex]m/s^2[/tex] b) hot rod travels 78.4 m c) time is 20 seconds

(a) To find the average acceleration, we need to use the formula: average acceleration = change in velocity / time.

First, we convert 60 km/h to m/s:

60 km/h x 1000 m/km x 1 h/3600 s = 16.67 m/s

So the change in velocity is:

16.67 m/s - 0 m/s = 16.67 m/s

And the time is:

7.5 s

Therefore, the average acceleration is:

average acceleration = (16.67 m/s) / (7.5 s) = 2.22 m/s^2

(b) To find the distance traveled, we can use the formula: distance = initial velocity x time + 0.5 x acceleration x time^2.

The initial velocity is 0 m/s, so the formula becomes:

distance = 0.5 x acceleration x time^2

Plugging in the values, we get:

distance = 0.5 x 2.22 m/s^2 x (7.5 s)^2 = 78.4 m

Therefore, the hot rod will travel 78.4 meters during the 7.5 seconds.

(c) We can use the formula: distance = 0.5 x acceleration x time^2, and solve for time.

Plugging in the values, we get:

0.40 km x 1000 m/km = 400 m

acceleration = 2.22 m/s^2

So the formula becomes:

400 m = 0.5 x 2.22 m/s^2 x time^2

Solving for time, we get:

time = sqrt(400 m / (0.5 x 2.22 m/s^2)) = 20 s

Therefore, it would take 20 seconds for the hot rod to travel 0.40 km with constant acceleration of 2.22 m/s^2.

Learn more about acceleration here:

https://brainly.com/question/12550364

#SPJ4

A GPS satellite orbits at an altitude of 20,200 km above the surface of the earth. What is the speed of the satellite? Recall that RE= 6.37 x 10^6 m

Answers

The speed of the GPS satellite can be calculated using the following formula:

How to calculate GPS satellite ?

v = √(GM/r)

where G is the gravitational constant, M is the mass of the Earth, r is the distance between the center of the Earth and the satellite, and v is the speed of the satellite.The distance between the satellite and the center of the Earth can be found by adding the radius of the Earth to the altitude of the satellite:

r = RE + h = 6.37 x 10^6 m + 20,200,000 m = 2.06 x 10^7 m

The mass of the Earth is M = 5.97 x 10^24 kg, and the gravitational constant is G = 6.67 x 10^-11 Nm^2/kg^2. Substituting these values into the formula, we get:

v = √(GM/r) = √((6.67 x 10^-11 Nm^2/kg^2)(5.97 x 10^24 kg)/(2.06 x 10^7 m)) ≈ 3,870 m/s

Therefore, the speed of the GPS satellite is approximately 3,870 m/s.

To know more about GPS satellite , check out :

https://brainly.com/question/478371

#SPJ4

a cooler (mass 3.6 kg) is initially at rest on a horizontal floor. it is then pushed in a straight line for 2 m by a small child who exerts a horizontal force with magnitude 30 n.
A.) Use the Work-Energy Theorem to determine the final speed of the cooler if there is no friction between the cooler and the floor. B.) Use the Work-Energy Theorem to determine the final speed of the cooler if the coefficient of kinetic friction between the cooler and the floor is 0.30.

Answers

(a) The final speed of the cooler is 5.77 m/s.

(b) In the presence of friction, the final speed of the cooler is 3.43 m/s.

What is the final speed of the cooler?

The final speed of the cooler is calculated by applying work energy theorem as shown below;

Change in kinetic energy of the cooler = work done on the cooler

¹/₂mv² = fd

v² = (2fd) / m

v = √(2fd) / m

where;

f is the applied forced is the displacement of the coolerm is the mass of the cooler

The final speed of the cooler is calculated as;

v = √(2 x 30 x 2) / 3.6

v = 5.77 m/s

At the given coefficient of friction, the final speed is calculated as;

v = √(2Ffd) / m

where;

Ff is force of friction

Ff = μW

where;

μ is coefficient of frictionW is the normal force

v = √(2μWd) / m

v = √(2 x 0.3 x 3.6 x 9.8 x 2) / 3.6

v = 3.43 m/s

Learn more about final speed here: https://brainly.com/question/28721263

#SPJ1

George is pushing his 20kg son, Jake, on the swing at the park. He pulls his son up to a height of 2m, pauses, and lets him go. What is Jake's kinetic energy before his dad lets go of the swing? What is Jake's kinetic energy at the lowest point? What is Jake's velocity at the top of the lowest point?

Answers

Jake's velocity at the lowest point of the swing is 7 m/s.

What is kinetic and potential energy?

Potential energy is the energy stored in any object or system due to the position or arrangement of its parts. It is, however, unaffected by factors outside of the object or system, such as air or height. Kinetic energy, on the other hand, is the energy of moving particles in an object or system.

To solve this problem, we need to use the conservation of energy principle, which states that the total energy in a system remains constant.

At the highest point, Jake has potential energy (due to his position above the ground), but no kinetic energy (since he is not moving).

As he swings down, his potential energy is converted to kinetic energy, and at the lowest point of the swing, he has the maximum kinetic energy and minimum potential energy. Then, as he swings back up, the process is reversed.

To calculate Jake's potential energy at the top of the swing, we use the formula:

PE = mgh

where m is the mass of Jake, g is the acceleration due to gravity (9.8 m/s²), and h is the height above the ground. Substituting in the values, we get:

PE = (20 kg)(9.8 m/s²)(2 m) = 392 J

This is Jake's potential energy at the top of the swing. At this point, he has no kinetic energy.

At the lowest point of the swing, Jake has converted all of his potential energy into kinetic energy. We can use the conservation of energy principle to find his kinetic energy at this point:

KE = PE

where KE is kinetic energy and PE is potential energy. Substituting in the values, we get:

KE = 392 J

This is Jake's kinetic energy at the lowest point of the swing.

To find Jake's velocity at the lowest point, we can use the formula for kinetic energy:

KE = (1/2)mv²

where v is velocity. Rearranging the formula to solve for v, we get:

v = √((2KE)/m)

Substituting in the values, we get:

v = √((2(392 J))/(20 kg)) = 7.0 m/s

This is Jake's velocity at the lowest point of the swing.

To know more about kinetic energy and potential energy follow

https://brainly.com/question/19637577

#SPJ1

The area labeled B is four times the area labeled A. Express b in terms of a.
The x y-coordinate plane is given. A curve and shaded region are graphed.
The curve y = ex enters the window in the second quadrant, goes up and right, crosses the y-axis becoming more steep, then exits the window in the first quadrant.
The shaded region A is below the curve and above the x-axis between x = 0 and x = a.

Answers

b in terms of a that satisfies the given condition is, [tex]b = \ln(3e^a - 2)[/tex].

The equation of the curve is y = e^x.

The shaded region A is the area under the curve between x = 0 and x = a, so its area is given by,

[tex]A = \int_0^a e^x dx = e^a - 1[/tex]

The area labeled B is four times the area labeled A, so its area is given by,

B = 4A = 4(e^a - 1)

To express b in terms of a, find the value of b that satisfies,

[tex]\int_0^a e^x dx = 3(e^a - 1)[/tex]

Using the formula for the integral of e^x, we get:

[tex]e^b - e^a = 3(e^a - 1)[/tex]

Solving for b, we get:

[tex]b = \ln(3e^a - 2)[/tex]

So the area labeled B is [tex]4(e^a - 1)[/tex], and the value of b that satisfies the given condition is [tex]b = \ln(3e^a - 2)[/tex].

To know more about the area, here

brainly.com/question/29893828

#SPJ4

When a weak stimulus is applied in rapid succession, it will often reach threshold due to
spatial summation.
excitatory summation.
voltage potential.
inhibitory summation.
temporal summation.

Answers

When a weak stimulus is applied in rapid succession, it will often reach threshold due to Temporal summation.

What is a stimulus ?

Stimulus is the effect that cause a change in the external or internal environment which brings physiological responses.

Here,

The weak stimulus applied is converted into a large signal so that it could reach the threshold.

Temporal summation is the phenomenon that could convert a series of weak stimuli at a specific frequency into a large signal and to achieve action potential.

Hence,

When a weak stimulus is applied in rapid succession, it will often reach threshold due to Temporal summation.

To learn more about stimulus, click:

https://brainly.com/question/30876577

#SPJ1

What will happen to an acceleration if the mass of an object is tripled, but the force is kept the same?

Answers

If the mass of an object is tripled while the force acting upon it is kept constant, the acceleration of the object will be reduced to one-third of its original value.

This can be explained using Newton's second law of motion, which states that the acceleration of an object is directly proportional to the force applied to it and inversely proportional to its mass.

In this scenario, the force is held constant, but the mass is increased by a factor of three. As a result, the acceleration will decrease by a factor of three, since the same force is now acting on a much heavier object. Therefore, the object will experience a lower acceleration than before, making it harder to move or change its speed or direction.

You can learn more about acceleration at

https://brainly.com/question/460763

#SPJ4

Calculate the height to which water at 4°C will rise in a capillary tube of 0.5 × 10^-3 m diameter. (Given g=9.8 m/s^2; angle of contact 0°; surface tension= 0.072 N/m.​

Answers

Step-by-step Explanation

Given: Diameter (D) of the capillary tube =  m

Surface Tension (T) =

The angle of contact () =

Acceleration due to gravity (g) =

The temperature of water =

To Find: The height (h) of rising of water in the capillary tube

Solution:

Formula to find the height of the rise

The following expression is used to find the height (h) of rising of water in the capillary tube;

Where,  is the density of water, and  is the radius of the capillary tube.

Calculating the height of the rise in the capillary tube

Since the diameter of the capillary tube is , the radius of the tube will be;

And, at , the density of water is

Substituting all the required values in the above formula, we get;

Hence, the water will rise in a capillary tube to a height of

If a machine does work faster, what does that mean about the power rating?

Answers

If a machine does some kind of work faster, then this mean that the power rating of the machine is higher. Power rating is directly proportional to the work done.

What is Power rating?

The power rating of an equipment is the highest power input which is allowed to flow through a particular equipment. According to the particular discipline, the power may be referred to as the electrical or mechanical power.

Work is proportional to the energy, and higher power means higher energy present in an object. If a machine does work at a faster rate, this means that it has high power rating.

Learn more about Power rating here:

https://brainly.com/question/26256725


#SPJ1

According to Newton's third law, what is the reaction force in the previous question to the normal force of the person on the floor? A. The gravitational pull of the person on Earth B. The gravitational pull of the box on Earth C. The force of the box on the person D. The normal force of the floor on the box E. The weight of the box F. The weight of the person G. The normal force of the box on the floor H. The force of the person on the box I. The normal force of the floor on the person

Answers

Answer:

A

Explanation:

A student wants to launch a toy dart toward a target that hangs from a light string: As time t = 0,the dart is launched with an initial speed v at an angle 0 above the horizontal ground: At the instant the dart is launched, the string is cut such that the target begins to fall straight down. The positive horizontal direction is considered to be to the right, and the positive vertical direction is considered to be up. 

Answers

A student wants to launch a toy dart As time t = 0, release a ball that has been resting near the Earth's surface. Allow a cart to leave rest and move down a 40°40° inclination with regard to the ground.

The graphs which could represent the vertical component of the velocity as a function of time for the dart and the target immediately after the dart is launched and the target begins to fall is Dart: above x-axis, decreasing; Target: below x-axis, decreasing.

Velocity is the directional speed of a moving object as an indicator of the rate at which its position changes as perceived from a given frame of reference and measured by a particular standard of time. The idea of ​​speed is important in kinematics, the part of classical mechanics that explains the motion of things.

Velocity is a physical vector quantity that requires both magnitude and direction to be determined. Velocity is a scalar absolute value of speed, a consistently derived unit whose quantity is measured in SI (metric system) in meters per second.

To know more about Velocity here-

https://brainly.com/question/17127206

#SPJ4

The above question is incomplete, the complete question is-

A student wants to launch a toy dart toward a target that hangs from a light string. At time t=0, the dart is launched with an initial speed v0 at an angle θ0 above the horizontal ground. At the instant the dart is launched, the string is cut such that the target begins to fall straight down. The positive horizontal direction is considered to be to the right, and the positive vertical direction is considered to be up.

Which of the following graphs could represent the vertical component of the velocity as a function of time for the dart and the target immediately after the dart is launched and the target begins to fall?

in a frictionless setup, two block of different masses are laying on two incline planes with different slopes and joined together by a pulley (see figure). find the acceleration of each block and the tension in the rope. also write the criteria (or equation) needed to be satisfied for block 2 to be moving down its incline plane.

Answers

Answer:

Explanation:

The problem you're describing involves two blocks connected by a rope over a pulley, with each block resting on a separate incline plane. The acceleration of each block and the tension in the rope can be determined using the principles of dynamics and conservation of energy.

Let's call the masses of the two blocks m1 and m2, the incline angles of the two planes θ1 and θ2, and the acceleration of each block a1 and a2.

The net force on each block is given by the sum of the gravitational force, the normal force, and the tension in the rope.

For block 1:

m1 * g * sin(θ1) - m1 * a1 = T

For block 2:

m2 * g * sin(θ2) - m2 * a2 = -T

where g is the acceleration due to gravity and T is the tension in the rope.

From these equations, we can see that the tension in the rope is equal in magnitude but opposite in direction for each block. The acceleration of each block can be found by rearranging the equations and solving for a1 and a2.

The condition for block 2 to be moving down its incline plane is that the net force on the block must be in the direction of motion, which means that the tension in the rope must be less than the gravitational force acting on the block. This can be expressed as:

T < m2 * g * sin(θ2)

Here is a definition of each variable in the problem:

m1: mass of block 1

m2: mass of block 2

θ1: incline angle of the first plane

θ2: incline angle of the second plane

a1: acceleration of block 1

a2: acceleration of block 2

g: acceleration due to gravity

T: tension in the rope

I hope this helps! Let me know if you have any other questions or if you need further clarification.

A metallic surface is illuminated by light. There is another metal plate a few cm away, which is held at an electric potential of V the plate is connected to a circuit which measures the current of electrons. When light of wavelength 520 nm is incident on the metal surface, electrons are emitted from the metal surface and absorbed by the second plate, which creates a current. When the potential of the second plate V is increased to Vstop =0.3 V, the current stops. 3.1 Photon energyWhat is the energy of each photon in electron volts?

Answers

The energy of each photon in electron volts is, 2.07.

Stopping potential is the minimum negative voltage applied to the anode to stop the photocurrent. The maximum kinetic energy of the electrons equal the stopping voltage, when measured in electron volt.

Stopping potential = Energy of light wave falling - energy of each photon

Energy of light wave falling = [tex]\dfrac{hc}{\lambda}[/tex]

Energy of light wave falling = [tex]\dfrac{hc}{\lambda}[/tex]

Energy in electron volts for a wave of wavelength 520 nm is, 2.37 eV.

Now,

Stopping potential = Energy of light wave falling - energy of each photon

0.3V = 2.37 - energy of each photon

Energy of each photon = 2.07

To know more about the Energy, here

brainly.com/question/17098905

#SPJ4

A thick, spherical shell of inner radius a and outer radius b carries a uniform volume charge density rho.
Find an expression for the electric field strength in the region a Express your answer in terms of r, a, b, rho, ϵ0.

Answers

Answer:

Explanation:

Here is the definition of each variable used in the expression for the electric field strength:

• r: radial distance from the center of the shell to the point where the electric field strength is being calculated

• a: radius of the shell

• b: thickness of the shell

• ρ_0: charge density in the shell

• ε_0: permittivity of free space, a constant that relates the electric flux density to the electric field strength. Its value is approximately 8.854 x 10^(-12) C^2/Nm^2.

• E: electric field strength, a vector quantity that describes the force experienced by a unit positive test charge placed at a particular point in an electric field.

• ∇: the gradient operator, a vector differential operator that describes the rate of change of a scalar field with respect to position.

• ∫: the definite integral symbol, denoting the sum of an infinite number of infinitesimal quantities over a specified range.

• dr': infinitesimal element of the radial distance used in the integration over the shell.

The electric field strength in a region is given by the gradient of the electric potential, V, in that region. The electric potential is related to the charge distribution, ρ, by the Poisson equation:

∇^2V = -(1/ε_0) * ρ

where ε_0 is the permittivity of free space.

If we assume the charge distribution is spherically symmetric, such that ρ = ρ(r), we can express the electric potential as:

V(r) = (1/4πε_0) * ∫(ρ(r')/|r-r'|) dV'

We can simplify this expression by assuming that the charge distribution is confined to a thin shell of radius a and thickness 2b, so that ρ(r) = ρ_0 for a-b <= r <= a+b and ρ(r) = 0 elsewhere. The electric potential in the region a can then be calculated by integrating over the shell:

V(r) = (1/4πε_0) * ρ_0 * ∫_{a-b}^{a+b} (1/|r-r'|) * dr'

To find the electric field strength, we need to take the gradient of the electric potential:

E = -∇V

Substituting in the expression for the electric potential, we get:

E = -∇[(1/4πε_0) * ρ_0 * ∫_{a-b}^{a+b} (1/|r-r'|) * dr']

So, the electric field strength in the region a is proportional to the gradient of the integral of the charge distribution over the shell, and is expressed in terms of the radius, a, the thickness, b, the charge density, ρ_0, and the permittivity of free space, ε_0.

57. You are driving through town at 12 m/s when suddenly a ball rolls out in front of you. You apply the brakes and begin decelerating at 3.5 m/s2. (a) how far do you travel before stopping? (b) When you have traveled only half the distance in part a, is your speed 6.0 m/s, greater than 6 m/s or less than 6 m/s? Support your answer with calculations.

Answers

a) Travelled 20.57 meters before coming to a stop.

b) When travelled half the distance, the speed is 2.6 m/s, which is less than 6 m/s.

What does speed mean?

Speed is a measure of how fast an object is moving, without regard to the direction of its motion. It is defined as the distance travelled by an object per unit of time. Speed is a scalar quantity, which means it only has magnitude (i.e., numerical value) and not direction. The standard unit of speed is meters per second (m/s) in the International System of Units (SI), although other units such as kilometres per hour (km/h) and miles per hour (mph) are also commonly used. It can be calculated as the ratio of distance traveled by an object to the time taken to cover that distance.

For example, if a car travels 100 meters in 10 seconds, its speed can be calculated as 100 meters divided by 10 seconds, which equals 10 meters per second. Speed can also be constant, if the object is moving at a constant rate without changing its speed, or variable, if the object's speed changes over time.

(a) To determine how far travelled before stopping, use the kinematic equation:

[tex]v^2 = u^2 + 2as[/tex]

where,

v = final velocity (0 m/s, since you come to a stop)

u = initial velocity (12 m/s)

a = acceleration (-3.5 m/s^2, since decelerating)

s = distance traveled (unknown)

Rearranging the equation to solve for s, we get:

[tex]s = (v^2 - u^2) / (2a)[/tex]

Substituting in the known values, we get:

[tex]s = (0 - (12 m/s)^2) / (2*(-3.5 m/s^2)) = 20.57 m[/tex]

Therefore, travelled 20.57 meters before coming to a stop.

(b) To determine speed, travelled half the distance, use the kinematic equation:

[tex]s = ut + 0.5at^2[/tex]

where,

t = time elapsed (unknown, but  use the fact that have travelled half the distance)

s = distance traveled (half of 20.57 m = 10.285 m)

u = initial velocity (12 m/s)

a = acceleration (-3.5 m/s^2)

Substituting the known values,

[tex]10.285 m = (12 m/s)t + 0.5(-3.5 m/s^2)t^2[/tex]

Simplifying and rearranging, a quadratic equation is obtained:

[tex]1.75t^2 - 12t + 10.285 = 0[/tex]

Solving  t using the quadratic formula,

t = 2.52 s (rounded to two decimal places)

Now, to find your speed at this point, we can use the kinematic equation:

[tex]v = u + at[/tex]

Substituting the known values,

[tex]v = 12 m/s + (-3.5 m/s^2)(2.52 s) = 2.6 m/s[/tex]

Therefore, when travelled half the distance, the speed is 2.6 m/s, which is less than 6 m/s.

To know more about Speed, visit:

https://brainly.com/question/13943409

#SPJ4

Learning Goal: To understand the meaning of the variables that appear in the equations for one-dimensional kinematics with constant acceleration.Motion with a constant, nonzero acceleration is not uncommon in the world around us. Falling (or threwn) objects and cars starting and stopping approximate this type of motion It is also the type of motion most frequently involved in introductory kinematics problems The kinematic equations for such motion can be written as z(t) = x + vt + at^2 v(t) = 1+ at where the symbols are defined as follows .A. X(t) is the position of the particle is the initial position of the particle . B. x(i) is the velocity of the particleC. v(t) is the initial velocity of the particle D. Vi is the acceleration of the particle

Answers

The variables in the kinematic equations for motion in one dimension with constant acceleration are time, initial position, initial velocity, initial acceleration, velocity, and position.

The following are accurate definitions for the variables in the kinematic equations for motion in one dimension with constant acceleration:

A. x(t) represents the particle's position at time t as determined by its initial position x. (0).

B. v(t) represents the particle's speed at time t as determined by its initial speed v. (0).

C. The particle's starting position, or the position at time t=0, is represented by the number x(0).

D. The initial velocity of the particle, or its speed at time t=0, is known as v(0).

E. an is the particle's constant acceleration.

It's vital to remember that the x and v subscripts denote the time at which the location or velocity is being measured. As an illustration, x(0) is the particle's position at time.

Learn more about acceleration here:

https://brainly.com/question/2303856

#SPJ4

in short-track speed skating, the track has straight sections and semicircles 16 min diameter. assume that a 68 kgskater goes around the turn at a constant 12 m/s.(figure 1)

Answers

The track in relatively brief speed skating has straight stretches and semicircles with a 16-minute diameter. This 68 kg skate makes the maneuver at a steady 12 m/s while exerting 1224 N.

What is speed and what is its unit in physics?

The pace at which a distance changes over time is referred to as speed. It has a dimension of time-distance. As a consequence, the fundamental unit of time as well as the basic measure of distances are combined to form the Special name of speed. Thus, the meter per second (m/s) is the Unit of measure of speed.

r = 8 m.

tangential velocity = 12 m/s.

angular speed is,

ω = v/r

= (12 m/s)/(8 m)

= 1.5 rad/s

centripetal acceleration,

a = r*ω²

= (8 m)*(1.5 rad/s)²

= 18 m/s².

force,

F = m*a

= (68 kg)*(18 m/s²)

= 1224 N

To know more about speed visit:

https://brainly.com/question/28224010

#SPJ4

Introduce CT scan and explain its working mechanism. ​

Answers

CT scans can produce detailed images of many structures inside the body, including the internal organs, blood vessels and bones. They can be used to: diagnose conditions including damage to bones, injuries to internal organs, problems with blood flow, stroke, and cancer.
Other Questions
Describe two advantages of planned economy excessive vagal stimulation of the heart will result in _______. To identify the genotype of yellow-seeded pea plants as either homozygous dominant (YY) or heterozygous (Yy), you could do a test cross with plants of genotype _______. the objective or literal meaning shared by most people using a word or symbol is the _______ meaning. Find the 11th term of the geometric sequence 7, 35, 175 Glenn Grimes is the founder and president of Heartland Construction, a real estate development venture The business transactions during February while the company was being organized are listed below Feb. 1 Grimes and several others invested $600,000 cash in the business in exchange for 25,000 shares of capital stock. Feb. 10 The company purchased office facilities for $277,500, of which $92,500 was applicable to the land and $185,000 to the building. A cash payment of $55,500 was made and a note payable was issued for the balance of the purchase price Computer equipment was purchased from PCWorld for $12,800 cash Feb. 16 Feb. 18 Office furnishings were purchased from Hi-Way Furnishings at a cost of $8,850. A $885 cash payment was made at the time of purchase, and an agreement was made to pay the remaining balance in two equal installments due March 1 and April 1. Hi-Way Furnishings did not require that Heartland sign a promissory note Feb. 22 Office supplies were purchased from Office World for $445 caslh Feb. 23 Heartland discovered that it paid too much for a computer printer purchased on February 16. The Feb. 27 Mailed Hi-Way Furnishings the first installment due on the account payable for office furnishings Feb. 28 Received $25 from PCWorld in full settlement of the account receivable created on February 23 unit should have cost only $360, but Heartland was charged $385. PCWorld promised to refund the difference within seven days purchased on February 18 a. Prepare journal entries to record the above transactions. Select the appropriate account titles from the following chart of accounts: (If no entry is required for a transaction/event, select "No journal entry required" in the first account field. Round your final answers to the nearest dollar amounts.) Cash Accounts Receivable Office Supplies Office Furnishings Computer Systems Office Building Notes Payable Accounts Payable Capital StockPrevious question Does anyone know the answer Thonks The 1960s was a very violent time. Why do you think that the peaceful protests led by Dr. Martin Luther King Jr. made a differences among all of the violence? A centric load P is applied to the granite block shown. The resulting maximum value of the shearing stress in the block is 3.4 ksi. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 6 in. 6 in. Determine the normal stress exerted on that surface. (Input the answer with the appropriate sign.) The normal stress exerted on that surface is ___ksi. In a neutral stable carbon atom with a mass of 11. Determine the number of protons,neutrons, and electrons.Number of Protons:Number of Neutrons:Number of Electrons: What is the slope of this line?-85864015-868 fill in the blank. the ceiling effect is when most participants select the___response, and the floor effect is when most participants select the response. please choose the correct answer from the following choices, and then select the submit answer button. Which of the following measures the number of days accounts receivable are held before the firm collects cash from the sale?A. Accounts receivable turnoverB. Average collection periodC. Average payment periodD. Accounts payable turnover Find the coordinates of the circumcenter of ABC with vertices A(-9, -4),B(-9, 8), and C(-1,0).The coordinates of the circumcenter are? Question 3 1 pts Say that Aliceland can produce 32 units of food per person per year or 16 units of clothing per person per year, but Georgeland can produce 16 units of food per year or 8 units of clothing. Which of the following is true? Georgeland has a comparative advantage, but not an absolute advantage, in producing clothing Georgeland has both a comparative and absolute advantage in producing clothing. O Aliceland has an absolute advantage, but not comparative advantage, in producing food. Aliceland has a comparative advantage, but not an absolute advantage, in producing food. What is the meaning of the no parking sign? A manufacturing firm has discontinued production of a certain unprofitable productline. This created considerable excess production capacity. Management is considering todevote this excess capacity to one or more of three product 1,2 and 3. The available capacityon the machines which might limit output are given below:Machine type Available time(in machine hours per week)Millingmachine250Lathe 150Grinder 50The number of machine hours required for each units of the respective product is givenbelow;Machine type Productivity (in machine hours/unit)Product 1 Product 2 Product 3Milling 8 2 3Lathe 4 3 0Grinder 2 0 1The unit profit would be 20 birr, 6 birr and 8 birr for products 1,2 and 3. Find how much ofeach product the firm should produce in order to maximise profit ? Solve the problem bysimplex method. A given amount of liquid at a specific temperature would not have a fixed volume.True or False? At the most basic level, the term atonement means "to reveal." A. TrueB. False Choose the geographic theme represented below. Bolivia is one of two landlocked South American countries in the Andes Mountains. Poverty here is high. It has three official languages: Spanish, Quechua, and Aymara. location place human-environmental interaction movement