Calculate the buffer ratio (base/acid) required for a buffer of pH = 5.68 that is prepared by mixing sodium hydrogen oxalate and sodium oxalate. A table of pKa values can be found here. Report your answer to 2 significant figures in scientific notation. Calculate the pH (to two decimal places) of the buffer solution after the addition of 7.77 g of sodium hydrogen carbonate (NaHOCOO) to the buffer solution above. Assume 5% approximation is valid and that the volume of solution does not change.

The mass of benzene that should be dissolved in 425g of water at 35°C to produce a solution with a vapor pressure of 36.1 mmHg is approximately 10.02 g.

1. Calculate the mole fraction of benzene (Xbenzene) in the solution using the following equation:

Ptotal = Xbenzene x P0benzene + Xwater x P0water

where Ptotal is the total vapor pressure of the solution, P0benzene is the vapor pressure of pure benzene, P0water is the vapor pressure of pure water, and Xwater = 1 - Xbenzene.

Rearranging the equation to solve for Xbenzene:

Xbenzene = (Ptotal - Xwater x P0water) / P0benzene

Substituting the given values:

Xbenzene = (36.1 mmHg - 0.953 x 42.2 mmHg) / 95.1 mmHg

Xbenzene = 0.390

2. Calculate the molality of the solution using the following equation:

molality = moles of solute / mass of solvent in kg

moles of solute = molality x mass of solvent in kg

Substituting the given values:

molality = 0.390 mol / kg

mass of solvent = 425 g = 0.425 kg

moles of solute = 0.390 mol / kg x 0.425 kg

moles of solute = 0.166 mol

3. Calculate the mass of benzene using its molar mass:

mass of benzene = moles of benzene x molar mass of benzene

Substituting the given values:

moles of benzene = 0.166 mol

molar mass of benzene = 78.11 g/mol

mass of benzene = 0.166 mol x 78.11 g/mol

mass of benzene = 12.97 g

However, we assumed that the density of the solution is equal to the density of water, which is not the case. Therefore, we need to adjust the mass of benzene by using the following equation:

mass of benzene = mass of solute / (1 - mass fraction of solute)

4. Calculate the mass fraction of benzene using the mole fraction:

mass fraction of benzene = (Xbenzene x molar mass of benzene) / (Xbenzene x molar mass of benzene + Xwater x molar mass of water)

5. Substituting the given values:

molar mass of water = 18.02 g/mol

mass fraction of benzene = (0.390 x 78.11 g/mol) / (0.390 x 78.11 g/mol + 0.610 x 18.02 g/mol)

mass fraction of benzene = 0.097

Substituting the values in the mass equation:

mass of benzene = 12.97 g / (1 - 0.097)

mass of benzene = 10.02 g

To know more about benzene, visit:

https://brainly.com/question/7284916

#SPJ1

Answer:

C

,

,

,

,

,

,

,

,

,

,

,

,

,

,,

,

,

The precision of the measurement is very good, measurements are within a very small range of each other. the accuracy of the measurement is not as good since the average measurement was 1.974g while the true mass was 1.975g.

Precision and accuracy are two important concepts in measurement. Precision is the degree of reproducibility or agreement of a set of measurements. It is usually expressed as the standard deviation of a set of measurements or the coefficient of variation. Accuracy is the degree of closeness to the true or accepted value of a measurement.

It is usually expressed as the difference between the measured value and the true or accepted value.

Learn more about precision and accuracy here:

https://brainly.com/question/5792909

#SPJ1

The substance with the greatest solubility in water is Ag2SO4, with a Ksp of 1.5 x 10-5.

The solubility of a substance is determined by its solubility product constant (Ksp). The higher the Ksp value, the more soluble the substance is in water.

Ksp is the equilibrium constant for a slightly soluble salt in a saturated solution. It is used to calculate the maximum concentration of ions in a solution at equilibrium. When a solid salt dissolves in water, it dissociates into its constituent ions.

The given values of Ksp for the substances are as follows:

BaF2, Kp = 1.5 x 10^-6

Ca(OH)2, Ksp - 6.5 x 10^-6

SrCros. Ksp = 2.2 x 10^-5

Ag2SO4, Ksp - 1.5 x 10^-5

Zn(103)2, Ksp = 3.9 x 10^-6

For more question on solubility click on

https://brainly.com/question/24057916

#SPJ11

The mass percent of the solution can be calculated using the following formula and the value we got is 49.3%.

Mass percent, also known as percent by mass or weight percent, is a way of expressing the composition of a mixture in terms of the mass of each component. It is calculated by taking the total mass of the mixture and dividing it by the mass of one component, then multiplying the result by 100%. Mass percent is often used to describe the concentration of a solution, as it gives the proportion of the solution that is composed of a particular component. For example, a solution with a mass percent of 10% of salt means that 10g of salt is present for every 100g of solution.

The mass of the solute (acetic acid) can be calculated using the molar mass of acetic acid, which is 60.05 g/mol.
0.26 mol acetic acid X (60.05 g/mol) = 15.51 g acetic acid
The mass percent of the solution can be calculated using the following formula:
(Mass of solute/Total mass) X 100 = Mass percent
(15.51 g/31.5 g) X 100 = 49.3%.

To learn more about mass percent
https://brainly.com/question/4336659
#SPJ1

Answer:

See below.

Explanation:

To determine the electron pair geometry of Carbonothioyl dibromide, we need to first draw its Lewis structure:

Br Br

\ /

C=S

/

Br Br

Carbonothioyl dibromide has four electron groups around the central sulfur atom: two single bonds with the two bromine atoms, one double bond with the carbon atom, and one lone pair of electrons on the sulfur atom.

Using VSEPR theory, we can predict the electron pair geometry by considering both the bonding and the lone pairs of electrons. In this case, the electron pair geometry of Carbonothioyl dibromide is tetrahedral because it has four electron groups around the central sulfur atom.

However, the molecular geometry of Carbonothioyl dibromide is trigonal pyramidal due to the presence of one lone pair of electrons on the sulfur atom.

Equation for pentane's balanced combustion: C5H12(l) + 8 O2(g) 5 CO2(g) + 6 H2O ( g)

For more information on combustion kindly visit to

https://brainly.com/question/15117038

#SPJ1

Answer: Hund's Rule

Explanation: The phenomenon is hund's rule of multiplicity.

The possible e₁ product of the given reaction is given below in the  image format.

Alkene products are produced in mixes via the elimination process. According to Zaitsev's rule, base-induced elimination results in the primary alkene product being the more strongly substituted double bond.

An chemical process known as a unimolecular elimination (E1) produces a double bond by removing an H-X substituent from an organic molecule. Because the creation of the carbocation intermediate (similar to an SN1 reaction) from simply the X substituent departing on its own is the reaction's rate-limiting step, it is unimolecular in nature:

A two-step process called an E1 elimination reaction uses a carbocation intermediate:

The elimination of the departing group is the mechanism's initial phase. In this instance, the bromine is the departing group.

The removal of a proton and creation of a double bond constitute the mechanism's second stage. The three substituents on the carbocation in this instance are all equivalent. The mechanism is demonstrated below:

Learn more about E1 products:

https://brainly.com/question/29490944

#SPJ4

Answer:

A compound is a material formed by chemically bonding two or more chemical elements. The type of bond keeping elements in a compound together may vary: covalent bonds and ionic bonds are two common types. The elements are always present in fixed ratios in any compound.

Explanation:

The displacement reaction will occur. The concentration of each spectator ion in the final solution is 3/2 moles of Fe2(CrO4)3 will be formed and Concentration of CrO4^2- will be  0.033 M

Step 1:

The balanced chemical equation for the reaction is given below:

K2CrO4 + FeCl3 -> Fe2(CrO4)3 + 2KCl

Hence, the reaction occurs between potassium chromate and iron (III) chloride.

Step 2:

We need to find out how much precipitate will be produced in grams.

Let's calculate the moles of reactants and then use mole ratio to find out the limiting reagent:

[tex]\[\text{Moles of potassium chromate} = \text{Molarity} \times \text{Volume} \div 1000\][Molarity of K2CrO4 = 2.5 M; Volume of K2CrO4 = 60.0 mL][/tex]

Moles of K2CrO4 = (2.5 x 60.0) / 1000 = 0.150 mol

[tex]\[\text{Moles of iron (III) chloride} = \text{Molarity} \times \text{Volume} \div 1000\][Molarity of FeCl3 = 3.2 M[/tex] = 3.2 M;

Volume of FeCl3 = 40.0 mL]Moles of FeCl3 = (3.2 x 40.0) / 1000 = 0.128 mol

As we see, K2CrO4 is the limiting reagent. So, FeCl3 is in excess.

Therefore, amount of Fe2(CrO4)3 precipitated is given by moles of K2CrO4 and mole ratio:

[tex]\[\text{Moles of Fe2(CrO4)3} = \text{Moles of K2CrO4} = 0.150 mol\][/tex]

Now, we will find the molecular weight of Fe2(CrO4)3 as 479.87 g/mol.

[tex]\[\text{Mass of Fe2(CrO4)3} = \text{Moles of Fe2(CrO4)3} \times \text{Molecular weight}\][/tex]

[tex]\[\text{Mass of Fe2(CrO4)3} = 0.150 \times 479.87 = 71.98\][/tex]

Therefore, the amount of precipitate produced is 71.98 g.c

We need to find out the concentration of each spectator ion in the final solution.

Firstly, we can write down the ionic equation for the reaction:

[tex]2 K+ + CrO4^2- + 3 Fe^3+ + 3 Cl^- - > 2 K+ + 3 Cl^- + Fe2(CrO4)3[/tex]

Now, we will check which ions remain in the final solution. We see that potassium and chloride ions are spectator ions. Hence, we don't need to calculate their concentration. The concentration of remaining ions can be calculated as follows:Fe3+ ions: In the given reaction, 3 moles of FeCl3 reacts with 2 moles of K2CrO4.

Hence, 3/2 moles of Fe2(CrO4)3 will be formed.

Therefore,

= [tex]\frac{3/2 \times 3.2 \times 40.0 \div 1000}{60.0 + 40.0}[/tex]

= 0.034 M\]CrO42- ions:

In the given reaction, 2 moles of K2CrO4 reacts with 3 moles of FeCl3.

Hence, 2/3 moles of Fe2(CrO4)3 will be formed.

Therefore,

Concentration{ of CrO4^2-}

= [tex]\frac{2/3 \times 2.5 \times 60.0 \div 1000}{60.0 + 40.0}[/tex]

= 0.033 M\]

For more such questions on displacement reaction , Visit:

https://brainly.com/question/20690229

#SPJ11

It's a negative value for ∆H°, indicating that the conversion of diamond to graphite releases energy. As a result, it is an exothermic reaction.

The conversion of diamond into graphite is exothermic. The enthalpy change of the reaction is -267.1 kJ.There are three reactions that take place in this process. Cdiamond (s) + O2 (g) → CO2(g) ∆H° = -395.4 kJ2 CO2 (g) → 2 CO(g)+O2 (g) ∆H° = 566.0 kJ2 CO2(g) → Cgraphite(s) + CO2 (g) ∆H° =-172.5 kJCdiamond (s) → Cgraphite (s) ∆H°= ?

The conversion of diamond to graphite is an endothermic process. It has a positive value of ∆H°. Therefore, the heat is absorbed by the surroundings. According to the first two reactions, the formation of CO and CO2 from the combustion of diamonds produces energy.

The net reaction for the conversion of diamond to graphite takes place as follows:

Diamond (s) + 2 O2(g) → Cgraphite (s) + 2 CO2 (g)

The energy change for this reaction can be determined by combining the above three reactions. The enthalpy change is obtained by subtracting the sum of the enthalpies of the reactants from the sum of the enthalpies of the products. The enthalpy change of the reaction is calculated as follows:

∆H°=ΣH°(products)−ΣH°(reactants)

∆H°=(−172.5)+(2×−393.5)+(566.0)−[(0)+(0)+(-395.4)+(2×0)]

∆H°=−267.1 kJ

To learn more about Exothermic reaction :

https://brainly.com/question/2924714

#SPJ11

The given reaction is classified as enamine hydrolysis. Enamine hydrolysis is a type of reaction that involves the hydrolysis of an imine group, leading to an aldehyde or ketone product. Option C.

The reaction proceeds by first forming an enamine intermediate by condensing an amine with an aldehyde or ketone, followed by an acid-catalyzed hydrolysis of the imine to produce a ketone or aldehyde product. The reaction can also be catalyzed by a base, although this is less common.
In the given reaction, an imine is hydrolyzed, resulting in an aldehyde or ketone product. The imine is formed when an amine reacts with an aldehyde or ketone, and the reaction of the imine with water is catalyzed by an acid. This reaction is known as enamine hydrolysis. Option C.

For more such questions on hydrolysis

https://brainly.com/question/31184126

#SPJ11

The names of the positions are called:

(1) (10) Atomic number

(2) (11) Chemical symbols

(3) (12) Elements

(4) (13) Atomic mass

Atomic structure refers to the composition and arrangement of subatomic particles within an atom. An atom consists of a central nucleus, which contains positively charged protons and uncharged neutrons, surrounded by negatively charged electrons that move around the nucleus in shells or energy levels.

The number of protons in the nucleus determines the atomic number and thus the identity of the element. The arrangement of electrons around the nucleus determines the chemical and physical properties of the element.

Learn more on atomic structure here: https://brainly.com/question/21289019

#SPJ1

The questions are:

10 What is the name for the number in this position called? (the answer is not "6") →6

11 What is the name for the letter in this position called? (the answer is not "C"!) →C

12 What is the name in this position called? (the answer is not "Carbon"!) →Carbon

13

What is the name for the number in this position? (the answer is not "12.0") →12.0

Use the spaces below to type your answers to the questions above.

The SI unit of pressure is the Pascal (Pa).

The boiling point of water is lower on Mount McKinley than the boiling point of water in NYC.

What is Pressure?

Pressure is defined as the amount of force applied perpendicular to the surface of an object per unit area over which that force is distributed. In other words, it is the force per unit area that an object exerts on another object. Pressure can be measured in various units such as pascal (Pa), bar, pounds per square inch (psi), and atmospheres (atm), among others. It is an important concept in physics and is used to describe many phenomena, including fluid dynamics, weather patterns, and even the behavior of gases in space.

At lower elevations, atmospheric pressure is higher compared to higher elevations.

Standard atmosphere or standard atmospheric pressure is equal to 101325 Pa.

Learn more about Pressure from given link

https://brainly.com/question/28012687

#SPJ1

According to the Bronsted-Lowry concept of acids and bases, the statement "If a base is strong, then its conjugate acid will be relatively weaker" is NOT true.

The Bronsted-Lowry concept defines an acid as a proton (H+) donor and a base as a proton acceptor. The strength of an acid or base is determined by the extent to which it is willing to donate or accept a proton. Therefore, when a strong acid donates a proton, the resulting conjugate base is also strong; likewise, when a strong base accepts a proton, the resulting conjugate acid is also strong.
Other characteristics of bases include the presence of a hydroxide group (OH-), and the ability to accept a proton (H+) to form a salt. However, the strength of a base does not necessarily depend on its presence or absence of a hydroxide group.
In conclusion, the Bronsted-Lowry concept of acids and bases states that the strength of a base does not determine the strength of its conjugate acid; therefore, the statement "If a base is strong, then its conjugate acid will be relatively weaker" is NOT true.

For more such questions on Bronsted-Lowry

https://brainly.com/question/24098522

#SPJ11

whereas the Early transition metal ions are generally quite oxophilic Lewis ligands they coordinate are Lewis A) acids; acids

When ligands make coordinate bonds with transition metal ions, they form a complex; the transition metal ion functions as a Lewis acid, while the ligand acts as a Lewis base.

Ligands are Lewis bases, which means they have at least one pair of electrons to provide to a metal atom/ion. Ligands are also referred to as complexing agents. Metal atoms/ions are Lewis acids, which means they may take electron pairs from Lewis bases.

According to the Lewis acid-base principle, the electron pair acceptor is known as the Lewis acid. Transition metals are electron-deficient in general and take electrons from ligands.

learn more about Transition metals

https://brainly.com/question/2879928

#SPJ1

Since the electronic configuration of nitrogen is 1s² 2s² 2p³, the number of electrons present in the nitrogen atom is 7, and the atomic number of nitrogen is also seven (7).

The atomic number of an atom is the number of protons in the nucleus of an atom. The number of protons defines the properties of an element. For example, if an element with 5 protons is boron atom.

The electronic configuration of an atom represents the number of electrons in each sub-energy level of the atom in the ground state.

The electronic configuration of nitrogen is 1s²2s²2p³. As you know, the electrons around the nucleus are located in energies or levels. Therefore, from the definition of electron configuration, we can say that the nitrogen atom has 2 electrons in the first energy level K of the s-subshell, and in the s-subshell and the p subshell of the second energy level L, respectively There are 2 or 3 electrons.

Therefore, the total number of electrons in the nitrogen atom is 7 (2 + 2 + 3). We know that the number of protons = the number of electrons, so the number of protons in the nitrogen nucleus is 7. Therefore, the nitrogen atom has an atomic number of 7.

For more information about electronic configuration, visit :

https://brainly.com/question/21977349

#SPJ4

When a particle undergoes beta decay, its atomic number increases by one.

The balanced equation of the  beta decay of uranium-235 is given below:

²³⁵₉₂U ---> ⁰₋₁e + ²³⁵₉₃Np

Beta decay is a type of radioactive decay that occurs when a nucleus emits a beta particle, which is an electron or a positron. During beta decay, a neutron or a proton inside the nucleus is transformed into the opposite type of particle.

In beta minus decay, a neutron in the nucleus is transformed into a proton, which remains in the nucleus, while an electron and an antineutrino are emitted. The electron is known as a beta particle.

In beta plus decay, also called positron emission, a proton in the nucleus is transformed into a neutron, which remains in the nucleus, while a positron and a neutrino are emitted. The positron is also known as a beta particle, but it has a positive charge.

Learn more about beta decay at: https://brainly.com/question/13174032

#SPJ1

A few common aspects to take into account, including the size of the participating atoms, the existence of lone pairs, numerous bonds, big groups connected to the core atom, or the environment the molecule is situated in

The orbitals that lone couples are in are smaller & rounder than orbitals that bonded pairs are in. Because of this, a bonding pair and a lone pair repel one another more strongly than two bonding pairs do. This significantly compresses the bonding pairs, lowering the  b.ed from 109.5° to 107°.

Trigonal pyramidal molecular geometry results from having three bond pairs and one lone pair of atoms (e.g. NH3). The geometry of the molecule is angular or curved when there's covalent bond pairs and three single electron pair pairs (e.g. H2O).

To know more about core atom visit:

https://brainly.com/question/17101420

#SPJ1

This is just one possible way to group and diagram the evolutionary relationships between these animals.

What is evolution?

Evolution is the process of change in the inherited characteristics of biological populations over successive generations. Evolutionary changes occur through a variety of mechanisms, including natural selection, genetic drift, gene flow, and mutations. Over time, these changes can result in the emergence of new species or the extinction of existing ones. Evolutionary theory provides an explanation for the diversity of life on Earth and has been supported by a vast amount of scientific evidence from multiple disciplines, including genetics, paleontology, and comparative anatomy. The theory of evolution by natural selection, developed by Charles Darwin and Alfred Russel Wallace in the mid-19th century, remains the fundamental concept in evolutionary biology.

Here is a diagram showing the possible evolutionary relationships between ten animals, along with their similarities:

Group 1: Mammals

Humans: Evolved from primates, similar to apes and monkeys

Elephants: Evolved from proboscideans, similar to mammoths and mastodons

Dolphins: Evolved from land mammals, similar to whales and porpoises

Group 2: Birds

Eagles: Evolved from theropod dinosaurs, similar to hawks and falcons

Penguins: Evolved from non-avian dinosaurs, similar to auks and puffins

Group 3: Reptiles and Amphibians

Crocodiles: Evolved from archosaurs, similar to alligators and caimans

Snakes: Evolved from lizards, similar to boas and pythons

Frogs: Evolved from fish, similar to toads and salamanders

Group 4: Insects

Bees: Evolved from wasps, similar to bumblebees and hornets

Butterflies: Evolved from moths, similar to skippers and hair streaks

Note: This is just one possible way to group and diagram the evolutionary relationships between these animals. There are many different ways to classify and categorize animals based on their evolutionary history and characteristics.

To know more about animals visit:-

https://brainly.com/question/25897306

#SPJ1

Answer:

C

Explanation:

PHYSICS

a gaseous substance that is below its critical temperature, and can therefore be liquefied by pressure alone.

The atomic mass of sulfur trioxide (SO3) is 82 amu.

Sulfur trioxide (SO3) has one sulfur atom and three oxygen atoms.

The atomic mass of sulfur can be calculated by subtracting the total mass of the oxygen atoms in sulfuric acid (3 x 16 amu) from the mass of sulfuric acid (98 amu) and then subtracting the mass of the remaining oxygen atom:

The atomic mass of sulfur is 34 amu.

To find the atomic mass of sulfur trioxide, we add the atomic masses of one sulfur atom and three oxygen atoms:

Therefore, the atomic mass of sulfur trioxide (SO3) is 82 amu.

Learn more about sulfur trioxide here : brainly.com/question/1458186

#SPJ1

Answer:

The mass of 2 moles of carbon tetrachloride is

307.646 grams

Explanation:

The chemical formula for Carbon tetrachloride is [tex]\ce{CCl_4}[/tex].  It contains 1 carbon atom and 4 chlorine atoms.

Carbon tetrachloride is formed due to the covalent bond between one carbon atom with four chlorine atoms.

In order to find the mass of 2 moles of [tex]\ce{CCl_4}[/tex] we need to determine the molar mass.

The molar mass of carbon is 12.011 g/mol.

The molar mass of chlorine is 35.453 g/mol.

As stated before we have 1 carbon atom and 4 chlorine atoms. So the molar mass can be evaluated by

[tex]\left(1*12.011\right)+\left(35.453*4\right)=153.823[/tex]

The molar mass of [tex]\ce{CCl_4}[/tex] is 153.823 g/mol.

You can multiply that by 2 to get the mass in grams of 2 moles of carbon tetrachloride.

[tex]2*153.823 =307.646[/tex]

Learn more about covalent bonds here

https://brainly.com/question/28808905

Answer: 1:1

Explanation:

Since Na trades place with Na it makes it 1:1

Answer:

To determine if the solution is saturated or unsaturated, we need to compare the amount of NaCl in the solution to its solubility in water at the given temperature.

The solubility of NaCl in water at room temperature (25°C) is approximately 36 grams per 100 grams of water, or 0.36 g/g. This means that at 25°C, water can dissolve up to 0.36 grams of NaCl per gram of water.

In this case, we have 2.75 grams of NaCl dissolved in 650 grams of water. To find the concentration of NaCl in the solution, we divide the mass of NaCl by the total mass of the solution:

concentration of NaCl = mass of NaCl / total mass of solution

concentration of NaCl = 2.75 g / (2.75 g + 650 g)

concentration of NaCl = 0.0042 g/g

Comparing the concentration of NaCl in the solution to its solubility in water at 25°C, we see that:

0.0042 g/g < 0.36 g/g

Since the concentration of NaCl in the solution is less than its solubility in water, the solution is unsaturated.

Explanation:

If we use the Gizmo to find the freezing, melting, and boiling points of water at 5,000 meters (16,404 feet) then,

Freezing point: 32 ºF (0ºC)

Melting point: 32 ºF (0ºC)

Boiling point: 203°F (95°C)

The freezing point is defined as the temperature at which a liquid becomes a solid. Increased pressure usually raises the freezing point with the melting point of the solid. The boiling point of a pure substance is defined as the temperature at which the substance transitions from a liquid to the gaseous phase. At the boiling point the vapor pressure of the liquid is equal to the applied pressure on the liquid. The melting point of a substance is defined as the temperature at which the substance changes from a solid to a liquid.

Melting occurs at a single temperature for the pure substances. The normal and average melting point and boiling point of water at 1 atmospheric pressure are 0°C and 100°C respectively. Decreasing the pressure under 1 atm. will lower the boiling point since the external pressure will be lower so it will become equal with the vapor pressure at a lower temperature.

To learn more about Freezing point

https://brainly.com/question/40140

#SPJ4

Answer: The Oxidation State Of Sulphur is +6

Explanation:

The volume ratios from the equation 2H2 + O2 → 2H2O are:

The coefficients in a balanced chemical equation give the ratio of moles of reactants and products. From the equation 2H2 + O2 → 2H2O, we can see that:

Therefore, the following volume ratios are valid:

What are the reactants?

The reactants are the substances that participate in a chemical reaction and are consumed to form new products. In the equation 2H2 + O2 → 2H2O, the reactants are hydrogen gas (H2) and oxygen gas (O2). These reactants undergo a chemical reaction to form water (H2O) as the product.

To know more about reactants, visit:

https://brainly.com/question/17096236

#SPJ1

The correct answer is bleaching of hair with hydrogen peroxide, curdling of milk by rennin and straightening frizzy hair by conditioner.

Protein denaturation is the process by which a protein loses its shape and function due to exposure to certain environmental conditions such as heat, pH, pressure, or chemical agents. The denaturation process can cause the protein's structure to unravel, leading to the loss of its biological activity. This happens because the protein's three-dimensional structure is crucial to its function, and when the structure is altered, the protein may no longer be able to perform its intended function.

Protein denaturation can occur reversibly or irreversibly depending on the extent of the damage to the protein's structure. Reversible denaturation occurs when the protein regains its structure and function once the environmental stressor is removed, while irreversible denaturation occurs when the damage is permanent and the protein cannot regain its function.

To know more about protein denaturation, visit:

https://brainly.com/question/19756195

#SPJ1

The full question is:

The denaturing of proteins occurs when the stabilizing forces are altered. Below is the set of processes in which proteins are denatured. Write the chemicals necessary for the denaturation to occur

1. Bleaching of hair

2. Curdling of milk

3. Straightening frizzy hair