3 For this force system the equivalent system at P is ___________ A FRP 40 lb along x dir and MRP 60 ft lbB FRP 0 lb and MRP 30 ft lbC FRP 30 lb along y dir and MRP 30 ft lbS FRP 40 lb along x dir and MRP 30 ft lb

Answers

Answer 1

This question is incomplete, the complete question is;

For this force system the equivalent system at P is ___________

A) FRP = 40 lb (along +x-dir.) and MRP = +60 ft.lb

B) FRP = 0 lb and MRP = +30 ft.lb

C) FRP 30 lb (along +y-dir.) and MRP  = -30 ft.lb

D) FRP 40 lb (along +x-dir.) and MRP = +30 ft.lb

Answer:

D) FRP 40 lb (along +x-dir.) and MRP = +30 ft.lb

Explanation:

From the figure in the image i uploaded along this answer;

FRP = ( 40 lb i + 30 lb j ) + [30 lb (-j)]

Where i  and j are the unit vectors along X & Y axis respectively.

So, FRP = 40 lb i

that is,  FRP = 40 lb along +X direction

MRP = [ 30 lb x ( 1 ' + 1' ) ] +( -30 lb x 1 ' )

= (30 lb x 2 ' )- 30 lb ft

= 60 lb ft - 30 lb ft

= 30 lb ft

Therefore option(D) is correct    

3 For This Force System The Equivalent System At P Is ___________ A FRP 40 Lb Along X Dir And MRP 60

Related Questions

A car traveling at 27 m/s slams on its brakes to come to a stop. It decelerates at a rate of 8 m/s2 . What is the stopping distance of the car?

Answers

v² - u² = 2 ax

where u = initial velocity (27 m/s), v = final velocity (0), a = acceleration (-8 m/s², taken to be negative because we take direction of movement to be positive), and ∆x = stopping distance.

So

0² - (27 m/s)² = 2 (-8 m/s²) ∆x

x = (27 m/s)² / (16 m/s²)

x ≈ 45.6 m

The stopping distance of car achieved during the braking is of 45.56 m.

Given data:

The initial speed of car is, u = 27 m/s.

The final speed of car is, v = 0 m/s. (Because car comes to stop finally)

The magnitude of deacceleration is, [tex]a = 8\;\rm m/s^{2}[/tex].

In order to find the stopping distance of the car, we need to use the third kinematic equation of motion. Third kinematic equation of motion is the relation between the initial speed, final speed, acceleration and distance covered.

Therefore,

[tex]v^{2}=u^{2}+2(-a)s[/tex]

Here, s is the stopping distance.

Solving as,

[tex]0^{2}=27^{2}+2(-8)s\\\\s = 45.56 \;\rm m[/tex]

Thus, we can conclude that the stopping distance of car achieved during the braking is of 45.56 m.

Learn more about the kinematic equation of motion here:

https://brainly.com/question/11298125

what causes chest pain is it by eating peppery food? ​

Answers

Answer:

Yes that is almost always the problem!

Explanation:

Answer:

the answer is Acid reflux hope this helped!

describe the energy conversion that occurs in a diesel engine

Answers

A diesel engine is a type of heat engine that uses the internal combustion process to convert the energy stored in the chemical bonds of the fuel into useful mechanical energy. ... First, the fuel reacts chemically (burns) and releases energy in the form of heat.

In a lightning bolt, a large amount of charge flows during a time of 1.2 x 10-3 s. Assume that the bolt can be represented as a long, straight line of current. At a perpendicular distance of 21 m from the bolt, a magnetic field of 8.4 x 10-5 T is measured. How much charged has flowed during the lightning bolt?

Answers

Answer: 10.58 C has flowed during the lightning bolt

Explanation:

Given that;

Time of flow t = 1.2 × 10⁻³

perpendicular distance r = 21 m

Magnetic field B = 8.4 x 10⁻⁵ T

Now lets consider the expression for magnetic field;

B = u₀I / 2πr

the current flow is;

I = ( B × 2πr ) / u₀

so we substitute

I = ( (8.4 x 10⁻⁵) × 2 × 3.14 × 21 ) / 4π ×10⁻⁷

=  0.01107792 / 0.000001256

= 8820 A

Hence the charge flows during lightning bolt  will be;

q = It

so we substitute

q = 8820 × 1.2 × 10⁻³

q = 10.58 C

therefore 10.58 C has flowed during the lightning bolt

"What will the pressure inside the container become if the piston is moved to the 1.60 L mark while the temperature of the gas is kept constant?"

Answers

This question is incomplete, the complete question is;

The Figure shows a container that is sealed at the top by a moveable piston, Inside the container is an ideal gas at 1.00 atm. 20.0°C and 1.00 L.

"What will the pressure inside the container become if the piston is moved to the 1.60 L mark while the temperature of the gas is kept constant?"

Answer:

the pressure inside the container become 0.625 atm if the piston is moved to the 1.60 L mark while the temperature of the gas is kept constant

Explanation:

Given that;

P₁ = 1.00 atm

P₂ = ?

V₁ = 1 L

V₂ = 1.60 L

the temperature of the gas is kept constant

we know that;

P₁V₁ = P₂V₂

so we substitute

1 × 1 = P₂ × 1.60

P₂ = 1 / 1.60

P₂ = 0.625 atm

Therefore the pressure inside the container become 0.625 atm if the piston is moved to the 1.60 L mark while the temperature of the gas is kept constant

What type of force holds atoms together in a crystal?

Answers

Answer:

Covalent Bond

Explanation:

i took the test , mark me brainliest.

Answer: Electrical

Explanation: Atoms are tied together by electrical bonding forces.

How much energy is used by a 1000 W microwave that operates for 5
minutes?

Answers

Answer:

300000 Joules

Explanation:

Recall that the unit Watts is Joules per second, derived from the quotient of energy per unite of time. Therefore, to calculate the energy used on the given time, we need to multiply the power used (1000 W) times the time used. Then we need to express the 5 minutes in seconds to get our answer in Joules:

5 minutes = 5 * 60 seconds = 300 seconds

Final energy calculation gives:

E = 1000 W * 300 sec= 300000 Joules

Someone help me I’ll give brainliest

Answers

Answer:

2.83 m/s

Explanation:

you have the right answer

I need help please help ! For science

Answers

Answer:

1, 5, 4, 6

Explanation:

bc

kerosene is able to reach the oher end of a wick by

Answers

Answer:

Capillary Action

Explanation:

Narrow spacings or pores are present in the wick, due to which capillary action takes place, that makes the oil to reach the other end of wick.  The ability of a liquid to flow in narrow spaces without any opposition or assistance of external force such as gravity is called as Capillary action.

A person drops a marble from the top of a skyscraper. After falling four floors the marble has gained a certain speed. How many more floors will the marble have to fall to triple this speed?

a. 8
b. 12
c. 32
d. 48

Answers

Answer:

B. 12

Explanation:

4 x 3 = 12

Before digital filmmaking, what tool was used to control the speed of movement on the screen after filming?

Answers

Answer:

The appropriate response is "Optical printer ".

Explanation:

A photographic printer used mostly for optical aberrations, comprised simply of either a camera that captures the frame to expand, minimize, deform, respectively. through magnifying lenses. A projector that always, as distinct from some kind of touch printer, transferred the image to something like the printing supply.

Calculate the effective charges on the H and F atoms of the HF molecule in units of the electronic charge, e.

Answers

Answer:

Explanation:

Hydrogen fluoride (HF) is an ionic/electrovalent compound that dissociates into ions when dissolved in water. It's dissociation is as seen below

HF ⇄ H⁺ + F⁻

There is a transfer of electron from the hydrogen atom which produces the hydrogen ion (H⁺), while the fluorine atom receives the donated ion to become negatively charged (F⁻). The amount of charge in one electron is generally given as 1.602 × 10⁻¹⁹ coloumbs.

The required value of effective charge on HF molecule, due to H and F is  1.602 × 10⁻¹⁹ Coulombs.

The given problem is based on the concept of effective charges. The net positive charge carried out by the electrons of atomic species, after forming a polyelectronic atom  is known as Effective charge.

As per the given problem, the Hydrogen fluoride (HF) is an ionic/electrovalent compound that dissociates into ions when dissolved in water. It's dissociation is given as,

HF ⇄ H⁺ + F⁻

There is a transfer of electron from the hydrogen atom which produces the hydrogen ion (H⁺), while the fluorine atom receives the donated ion to become negatively charged (F⁻). The amount of charge in one electron is generally given as 1.602 × 10⁻¹⁹ Coulombs.

Thus, we can conclude that the required value of effective charge on HF molecule, due to H and F is 1.602 × 10⁻¹⁹ Coulombs.

Learn more about the effective charge here:

https://brainly.com/question/25002720

Find the linear velocity of a point moving with uniform circular motion, if the point covers a distance s in the given amount of time t. s

Answers

Answer:

The linear velocity is represented by the following expression: [tex]v = \frac{s}{t}[/tex]

Explanation:

From Rotation Physics we know that linear velocity of a point moving with uniform circular motion is:

[tex]v = r\cdot \omega[/tex] (Eq. 1)

Where:

[tex]r[/tex] - Radius of rotation of the particle, measured in meters.

[tex]\omega[/tex] - Angular velocity, measured in radians per second.

[tex]v[/tex] - Linear velocity of the point, measured in meters per second.

But we know that angular velocity is also equal to:

[tex]\omega = \frac{\theta}{t}[/tex] (Eq. 2)

Where:

[tex]\theta[/tex] - Angular displacement, measured in radians.

[tex]t[/tex] - Time, measured in seconds.

By applying (Eq. 2) in (Eq. 1) we get that:

[tex]v = \frac{r\cdot \theta}{t}[/tex] (Eq. 3)

From Geometry we must remember that circular arc ([tex]s[/tex]), measured in meters, is represented by:

[tex]s = r\cdot \theta[/tex]

[tex]v = \frac{s}{t}[/tex]

The linear velocity is represented by the following expression: [tex]v = \frac{s}{t}[/tex]

PLEASE HELP EASY MULTIPLE CHOICE!!!!!!!!!!!

Answers

Answer:

options C is correct

Explanation:

asking questions is super in this education life

Answer:

option c should be the answer

Calculate the work WC done by the gas during the isothermal expansion. Express WC in terms of p0, V0, and Rv.

Answers

Complete Question

The complete question is shown on the first and second uploaded image

Answer:

The expression is  [tex]W_c =  P_o V_o ln (R_v)[/tex]  

Explanation:

Generally smallest workdone done by  a gas is mathematically represented as

          [tex]dW  =  PdV[/tex]

Generally for an isothermal process

    [tex]PV  =  nRT = constant [/tex]

=>   [tex]P = \frac{nRT}{V}[/tex]

Generally the total workdone is mathematically represented as

   [tex]W_c =  \int\limits^{v_f}_{V_o} {\frac{nRT}{V} } \, dV[/tex]

=> [tex]W_c = nRT  \int\limits^{V_f}_{V_o} {\frac{1}{V} } \, dV[/tex]

=>  [tex]nRT [lnV]   | \left \ {V_f}} \atop {V_o}} \right.[/tex]

=>  [tex]W_c = nRT [ln(V_f) - ln(V_o)][/tex]

=>  [tex]W_c = nRT ln \frac{V_f}{V_o}[/tex]

From the question [tex]\frac{V_f}{V_o }  =  R_v[/tex]

=> [tex]W_c =  P Vln (R_v)[/tex]

at initial  state

[tex]W_c =  P_o V_o ln (R_v)[/tex]  

what is the meaning of the word physics​

Answers

Answer:

the scientific study of natural forces such as light, sound, heat, electricity, pressure, etc.

Explanation:

mark as brainliest

Which best explains a difference between Einstein’s general theory of relativity and his special theory of relativity?


His general theory includes uniform and accelerated motion, but his special theory applies only to uniform motion.

His general theory includes uniform and accelerated motion, but his special theory applies only to accelerated motion.

His general theory applies only to accelerated motion, but his special theory includes uniform and accelerated motion.

His general theory applies only to uniform motion, but his special theory includes uniform and accelerated motion.

Answers

Answer:

His general theory includes uniform and accelerated motion, but his special theory applies only to uniform motion.

Explanation:

According to Einstein's 1915 general theory of relativity, the force of gravity arises from the curvature of space and time.

According to theory of special relativity:

1. The laws of physics are the same for all non-accelerating observers

2. The speed of light in a vacuum was independent of the motion of all observers.

His general theory includes uniform and accelerated motion, but his special theory applies only to uniform motion.

Answer:

for those who dont like to read

the answer is A.

hope i helped

Explanation:

What resistance must be connected in parallel with a 633-Ω resistor to produce an equivalent resistance of 205 Ω?

Answers

Answer:

303 Ω

Explanation:

Given

Represent the resistors with R1, R2 and RT

R1 = 633

RT = 205

Required

Determine R2

Since it's a parallel connection, it can be solved using.

1/Rt = 1/R1 + 1/R2

Substitute values for R1 and RT

1/205 = 1/633 + 1/R2

Collect Like Terms

1/R2 = 1/205 - 1/633

Take LCM

1/R2 = (633 - 205)/(205 * 633)

1/R2 = 428/129765

Take reciprocal of both sides

R2 = 129765/428

R2 = 303 --- approximated

What type of research based on approach that used to describe variables rather than to test a predicted relationship between variables?

Answers

Answer:

Correlational research can be used to see if two variables are related and to make predictions based on this relationship.

calculate earths velocity of approach toward the sun when earth in its orbit is at an extremum of the latus rectum through the sun

Answers

Answer:

Hello your question is incomplete below is the complete question

Calculate Earths velocity of approach toward the sun when earth in its orbit is at an extremum of the latus rectum through the sun, Take the eccentricity of Earth's orbit to be 1/60 and its Semimajor axis to be 93,000,000

answer : V = 1.624* 10^-5 m/s

Explanation:

First we have to calculate the value of a

a = 93 * 10^6 mile/m  * 1609.344 m

  = 149.668 * 10^8 m

next we will express the distance between the earth and the sun

[tex]r = \frac{a(1-E^2)}{1+Ecos\beta }[/tex]   --------- (1)

a = 149.668 * 10^8

E (eccentricity ) = ( 1/60 )^2

[tex]\beta[/tex] = 90°

input the given values into equation 1 above

r = 149.626 * 10^9 m

next calculate the Earths velocity of approach towards the sun using this equation

[tex]v^2 = \frac{4\pi^2 }{r_{c} }[/tex]   ------ (2)

Note :

Rc = 149.626 * 10^9 m

equation 2 becomes

([tex]V^2 = (\frac{4\pi^{2} }{149.626*10^9})[/tex]

therefore : V = 1.624* 10^-5 m/s

A designer is creating an obstacle for an obstacle course where a person starts on a moveable platform of height H from the ground. The person grabs a rope of length L and swings downward. At the instant the rope is vertical, the person lets go of the rope and attempts to reach the far side of a water-filled moat. The left side of the moat is directly below the position where the person will let go of the rope. The designer runs several tests in which the rope has different lengths and moves the platform such that the rope is always initially horizontal. The designer notices that the person cannot land on the other side if the length L is very short. The designer also notices that the person also cannot land on the other side if the length L is very close to the height H.

Assume the size of the person is much smaller than the lengths L and H. Let D represent the horizontal distance from below the release point to where the person lands.

Required:
a. Why does the person land in the moat if the rope's length is very short?
b. Why does the person land in the moat if the length is nearly the same as the height of the platform?

Answers

Answer:

* when L → H    chord too long

in this case we see that the speed to cross the well grows a lot (it goes towards infinity) therefore we do not have enough speed in the movement to cross

* when L → 0 very short string

         the speed of the platform is very small, so we do not have the minimum required value

        vox = √ (g / (2 (H)) D

Explanation:

For this exercise we are going to solve it using conservation of energy to find the velocity of the body and the launch of projectiles to find the velocity to cross the well.

Let's start with the projectile launch

as the body leaves the vertical its velocity must be horizontal

         x = v₀ₓ t

         y = y₀ + [tex]v_{oy}[/tex] t - ½ g t²

when reaching the ground its height of zero (y = 0) and the initial vertical velocity is zero

         t = √ 2 y₀ / g

we substitute

        x = vox √2y₀ / g

        v₀ₓ = √(g / 2y₀)     x

In the exercise, it tells us that the width of the well is D (x = D) and the initial height is the height of the platform minus the length of the rope (I = H - L)

       v₀ₓ = √(g /(2 (H -L))    D

this is the minimum speed to cross the well.

Now let's use conservation of energy

starting point. On the platform

      [tex]Em_{o}[/tex] = U = m g H

final point. At the bottom of the swing

      Em_{f} = K + U = 1 / 2m v² + m g (H -L)

as there is no friction the mechanical energy is conserved

        Em_{o} = Em_{f}

       m g H = 1 / 2m v² + m g (H -L)

        v = √ (2gL)

let's write our two equations

the minimum speed to cross the well

       v₀ₓ = √ (g /(2 (H -L))    D

the speed at the bottom of the oscillatory motion

       v = √ (2g L)

we analyze the extreme cases

* when L → H    chord too long

in this case we see that the speed to cross the well grows a lot (it goes towards infinity) therefore we do not have enough speed in the movement to cross

* when L → 0 very short string

         the speed of the platform is very small, so we do not have the minimum required value

        vox = √ (g / (2 (H)) D

From this analysis we see that there is a range of lengths that allows us to have the necessary speeds to cross the well

      V₀ₓ = v

      g / (2 (H -L) D² = 2g L

       4 L (H- L) = D²

        4 H L - 4 L2 - D² = 0

        L² - H L - D² / 4 = 0

let's solve the quadratic equation

      L = [H ± √ (H2-D2)] / 2

we assume that H> D

       L = ½ H [1 + - RA (1 - (D / H) 2)]

The two values ​​of La give the range of values ​​for which the two speeds are equal

A) The person lands in the moat if the rope's length is very short because :

The speed of the platform is less than the required minimum speed

B) The person lands in the moat if the rope length is similar to the height of the platform because :

The speed required to cross the moat approaches infinity

Following the assumptions;

size of the person is much smaller than L and H

D = horizontal distance

The conditions that will cause the person to land on the moatThe person will land in the moat when the rope's length is very short because as the rope reduces in length the speed reduces as well such that the speed of the platform goes below the required minimum speed which will enable the person cross over.  while As the magnitude of the length tends towards the same magnitude of the height the speed required to cross the moat increases towards infinity and this speed cannot be attained by the person hence he will land in the moat.

Hence we can conclude that The person lands in the moat if the rope's length is very short because The speed of the platform is less than the required minimum speed  and  The person lands in the moat if the rope length is similar to the height of the platform because,the speed required to cross the moat approaches infinity.

Learn more about obstacle course : https://brainly.com/question/241926

If car A is at 40km/h and car B is at 10km/h in the opposite direction, what is the velocity of the car A relative to the car B?. ​

Answers

Explanation:

The velocity of car A relative to car B is (10km/h+40km/h)=50km/h

Design a tension member and slip-critical splice to carry a factored load of 500 kips. Please use a wide-flange section for the tension member. Please use A572 Gr. 50 steel plates for the splice plates. Please use Group B, A490 bolts for the splice connection. The splice connection should be slip-critical, and have adequate strength after slip occurs as well. Please make any other assumptions you need in order to complete the problem. Provide detailed sketches and drawings for your design.

Answers

Answer:

Kindly check the explanation section.

Explanation:

For the design we are asked for in this question/problem there is the need for us to calculate or determine the strength in fracture and that of the yield. Also, we need to calculate for the block shear strength.

From the question, we have that the factored load = 500kips. Also, note that the tension splice must not slip.

Also, the shear force are resisted by friction, that is to say shear resistance = 1.13 × Tb × Ns.

Assuming our db = 3/4 inches, then the slip critical resistance to shear service load = 18ksi(refer to AISC manual for the table).

If db = 7/8 inches, then the shear force resistance for n bolt = 10.2kips, n > 49.6.

The yielding strength = 0.9 × Aj × Fhb= 736 kips > 500

The fracture strength = .75 × Ah × Fhb = 309 kips.

The bearing strength of 7/8 inches bolt at the edge hole and other holes = 46 kips and 102 kips.

A recipe gives the instructions below
After browning the meat pour off fat from the pan to further reduce fat use a strainer.

what type lf separation methods are described in the recipe

A decantation and screening
B distillation and screening
C decantation and centrifugation
D distillation and filtration

Answers

Answer:

A. decantation and screening

Explanation:

Decantation is the one of the process of separating the mixture. In this process the precipitated liquid is separated from the solid. According to the given instruction for the recipe, the fat which is in liquid state is separated from meat. In the process of screening, more liquid is separated by placing the mixture on the screen. Here, the gravity plays an important role for the process of separation.  

Answer:

a

Explanation:

An increase in temperature the kinetic energy and average speed of the gas particles. As a result, the pressure on the walls of the container . Answer Bank What temperature must a gas, initially at 10 ∘C, be brought to for the pressure to triple?

Answers

Answer:

a

The pressure will increase

b

[tex]T_2 =  576^oC[/tex]

Explanation:

From the ideal gas law we have that

     [tex]PV  =  nRT[/tex]

We see that the temperature varies directly with the pressure so if there is an increase in temperature that pressure will increase

   The initial  temperature is [tex]T_i  =  10^oC = 10 + 273 =  283 \  K [/tex]

The objective of this solution is to obtain the temperature of the gas where the pressure is tripled

Now from the above equation given that nR and V  are constant  we have that

    [tex]\frac{P}{T}  =  constant[/tex]

=>  [tex]\frac{P_1}{T_1}  =\frac{P_2}{T_2}[/tex]

Let assume the initial  pressure is [tex]P_1 =  1 Pa[/tex]

So tripling it will result  to the pressure being [tex]P_2 =  3 Pa[/tex]

So

     [tex]\frac{1}{283}  =\frac{3}{T_2}[/tex]  

=>   [tex]T_2  =  3 *  283[/tex]

=>    [tex]T_2  =  3 *  283[/tex]

=>    [tex]T_2  = 849 \ K [/tex]

Converting back to [tex]^oC[/tex]

   [tex]T_2  =  849 -  273[/tex]

=>  [tex]T_2 =  576^oC[/tex]

What does g stand for

Group of answer choices

gravity

The acceleration of gravity

The force of gravity

Answers

Answer:

the acceleration of gravity.

Answer:

g stand for the acceleration of gravity .

Explanation:

A car starts from rest and accelerates uniformly over a time of 18 seconds for a distance of 390 m. Determine the acceleration of the car.

Answers

Answer:

[tex]a=2.4\ m/s^2[/tex]

Explanation:

Given that,

The initial speed of a car, u = 0

Time, t = 18 s

Distance, d = 390 m

We need to find the acceleration of the car. Let it is a. Using the second equation of motion to find it.

[tex]d=ut+\dfrac{1}{2}at^2[/tex]

or

[tex]d=\dfrac{1}{2}at^2\\\\a=\dfrac{2d}{t^2}\\\\a=\dfrac{2\times 390}{(18)^2}\\\\a=2.4\ m/s^2[/tex]

So, the acceleration of the car is [tex]2.4\ m/s^2[/tex].

HELP PLS7. A steel ball is dropped from a height of 100 meters. Which velocity-time graph best describes the
motion of the ball?

Answers

Answer:

Option C.

Explanation:

To know which velocity-time graph best describes the motion of the ball, let us calculate the velocity of the ball and the time taken for the ball to get the ground. This can be obtained as follow:

1. Determination of the velocity.

Initial velocity (u) = 0 m/s

Acceleration due to gravity (g) = 9.8 m/s²

Height (h) = 100 m

Final velocity (v) =.?

v² = u² + 2gh

v² = 0² + (2 × 9.8 × 100)

v² = 0 + 1960

v² = 1960

Take the square root of both side.

v = √(1960)

v = 44.27 m/s

2. Determination of the time taken.

Acceleration due to gravity (g) = 9.8 m/s²

Height (h) = 100 m

Time (t) =.?

h = ½gt²

100 = ½ × 9.8 × t²

100 = 4.9 × t²

Divide both side by 4.9

t² = 100 / 4.9

Take the square root of both side

t = √(100 / 4.9)

t = 4.52 s

From the above illustration,

Initial time (t1) = 0 s

Final time (t2) = 4.52 s

Initial velocity (u) = 0 m/s

Final velocity (v) = 44.27 m/s

Thus, we can see that as the time increase, the velocity also increase. Therefore, option C gives the correct answer to the question.

A truck with a mass of 1330 kg and moving with a speed of 15.0 m/s rear-ends a 805 kg car stopped at an intersection. The collision is approximately elastic since the car is in neutral, the brakes are off, the metal bumpers line up well and do not get damaged. Find the speed of both vehicles after the collision in meters per second.

Answers

Answer:

The Speed of the vehicles is 9.34m/s

Explanation:

For an elastic collision the two bodies move with similar velocities after collision

Given

M1=1330kg

V1=15m/s

M2=805kg

V2=0(the car is parked on neutral)

The formula is

M1V1+M2V2=(M1+M2)V

1330*15+805*0=(1330+805)V

19950+0=2135V

2135V=19950

divide both sides by 2135

V=19950/2135

V=9.34m/s

Other Questions
Which of the following is not a process that occurs during cytokinesis of an animal cell?(Please help I will mark brainliest)A. Cytoplasm is dividedB. Nucleus reappearsC. Chromosomes line up at the metaphase plateD. Nuclear envelope surrounds chromosomes With as much as detail as possible, give another example of an analogy for describing the difference between prokaryotic cells and eukaryotic cells Which of the following describes the extent to which many families with Deaf children learn ASL?1. many families with Deaf children become so inspired by learning ASL that they become professional interpreters2. many families with Deaf children learn some ASL but then hire a tutor when their child is of school age to supplementASL education3. many families with Deaf children must be fluent in ASL because they need to start teaching their children ASL assoon as possible4. some families with Deaf children become fluent in ASL, but many do not The circle shown has a radius of 12 mm. What is the circumference of the circle? PLEASE PLEASE HELP I NEED THIS RIGHT NOW Which sentence uses superfluous correctly?A. The water started flowing from the new sprinkler system in a superfluous way. B. The water was supefluous to the runners after the marathon.C. After the power came back on, the use of flashlights was superfluous. D. The new instructor found the class to be superfluous and attentive. After referring to the text, describe the significance of this warrior being depicted on horseback. Please help me out! Multiply. Do not round your answer.2.48x8.62 =? Mechanistic vs. Organic Structures Managers taking a contingency approach must consider numerous factors in designing the best kind of structure for their particular organization at that particular time. British behaviorists Tom Burns and G.M. Stalker identified what they call mechanistic and organic structures. Depending on the task environment and a variety of other considerations, the type of organizational structure chosen can be critical to organizational success. This exercise will test your knowledge of the characteristics of each of these types of organizational structure.Select the most appropriate category (mechanistic or organic structure) for each of the characteristics of organizations. 1. Few rules and procedures 2. Narrow span of control 3. Specialized tasks 4. Many teams or task forces5. Many rules and procedures 6. Decentralized hierarchy of authority 7. Flatter structure 8. Informal communication 9. Taller structure 10. Centralized hierarchy of authority 11. Wider span of control 12. Shared tasks 13. Formalized communication 14. Few teams or task forces Category:a. Mechanistic Organizations b. Organic Organizations A boat costs $15.500 and decreases in value by10% per year. How much will the beat be worthafter 5 years? What is the slope of a line that is parallel to the line joining (7,-5) and (-5,7) An objects volume is 0.12 kL. What is its volume in liters? The students can make 6 tickets from each sheet of paper. How many sheets of paper. How many sheets of paper are needed for 125 tickets? What is the measure of ZRIA?RPAN999.A. 55B. 30O C. 95D. 60 Yea I need help with fractions What does 7 hundreds10 equal? Let x be a continuous random variable that is normally distributed with a mean of 25 and a standard deviation of 6. Find the probability that x assumes a value between 29.0 and 55.0. Use Table IV in Appendix C to compute the probabilities. Round your answer to four decimal places. f(x)=-5/2 x-3A. Create a linear function g(x) such that f(x) = g(x) has exactly one solution. g(x) = ? B. What is the exact solution to f(x) = g(x)? x = ?Step by step Please help with number 7 thank you! 30 points It was late, but Jen was hungry anyway. She had been toobusy to eat all day, and now all she could think about was ahamburger and fries, and maybe a milkshake, too. Jenpulled into the drive-thru, but found that it had closed at 10p.m. Jen sighed. What else might be open? She spotted a24-hour joint across the street. She looked both ways andpulled out into the road again.What can you infer from the text?A. Jen is thinking about a burger and fries.B. Jen drives to another place.C. Milkshakes are not good for you.D. Jen pulls out of the drive-thru.