If the volume of the gases in the container taken in STP is equal they they contains equal number of moles of the gas. As the volume increases, mobility of gases increases.
What is Avogadro's law ?Avogadro's law states that, at constant pressure and temperature, the volume of gas is directly proportional to the number of moles. If two gases at STP have equal volume, they contains equal number of moles.
The temperature of 298 K and 1 atm pressure is taken as standard condition (STP). At STP, the volume of one mole of every substance contains 22.4 L volume.
The carbon dioxide gas and fluorine gas if taken in equal volume at STP, they contain equal number of moles. Then, the average speed is inversely proportional to mass. Then , fluorine gas will have greater speed.
Find more on Avogadro's law:
https://brainly.com/question/3491421
#SPJ9
Which part of the economy is represented by box C on the circular flow model?
Box C in the circular flow model represents households, or consumers.
What does the circular flow model depict?In the circular flow model, households are shown as the source of spending and demand for goods and services in the economy.
The model depicts a continuous flow of money from households to firms, in exchange for goods and services, and then from firms back to households as wages and profits. Box C is typically depicted as one of two boxes on either side of the model, representing either households or firms. The other box, Box F, typically represents firms, or producers.
Therefore, the correct answer is as given above. It could then be concluded that the correct answer is that Box C in the circular flow model represents households, or consumers.
learn more about circular flow model: https://brainly.com/question/1433471
#SPJ1
which of the following correctly expresses energy in terms of planck's constant? select all that apply. multiple select question. e
Energy in terms of Planck's constant can be expressed by the equation: E = hν or E = hc/λ, where E, h, ν, c and λ represent energy, Planck's constant, frequency, speed of light and wavelength, respectively.
How does energy relate to Planck's constant?The result of multiplying energy by time, or action, is the dimension of Planck's constant. Therefore, the definition of Planck's constant as the fundamental quantum of activity is common.
What formula employs the Planck constant?The Planck-Einstein relation, which establishes Planck's constant, has the following form: E = hf. Here, E denotes the energy of each light packet (or "quanta") in Joules, f is the frequency of light in hertz, and h, of course, denotes Planck's constant.
To learn more about Planck's constant visit:
brainly.com/question/27389304
#SPJ1
On a T-v diagram, the saturated liquid states can be connected by a line called the _________ liquid line, and the saturated vapor states can be connected by the _________ vapor line.
A line known as the Saturated Liquid Line can be used to connect the saturated liquid states on a T-V diagram, while the Saturated Vapor Line can be used to connect the saturated vapor states.
What is Saturated Vapor Line?In the T-s diagram, the curve separating the two-phase state from the superheated vapor state is known as the saturation vapor curve. The T-s diagram's saturated liquid curve is the line dividing the subcooled liquid state from the two-phase state. The term "saturated liquid line" refers to a line that connects all saturated liquid states. The saturated vapor line connects all of the saturated vapor states. Both the saturated liquid state and the saturated vapor state combine into a single point on the T-v diagram when pressure reaches Pcr (critical pressure).The saturation line is the area beyond which a substance or component in a system either changes from liquid to vapor or vapor to liquid according to the Temperature Pressure Equilibrium Diagram.To learn more about Saturated Vapor Line, refer to:
https://brainly.com/question/18095323
#SPJ4
Which of the following transitions in the hydrogen atom would result in the emission of a photon with the longest wavelength? How do you know?a. n = 1 to n = 2 b. n = 3 to n = 1 c. n = 2 to n = 1 d. n = 4 to n = 3 e. n = 1 to n = 4
The transition that would result in the emission of a photon with the longest wavelength is from n = 4 to n = 3 (Option d).
This is because the energy of a photon is inversely proportional to its wavelength. According to the Rydberg formula, the energy of a photon emitted or absorbed during a transition in a hydrogen atom is given by:
[tex]E = Rh[(1/n_1^2) - (1/n_2^2)][/tex]
where Rh is the Rydberg constant, n1 and n2 are the initial and final quantum numbers of the electron, respectively.
As we move from higher to lower energy levels, the difference in energy levels decreases, resulting in a longer wavelength for the emitted photon. In this case, the transition from n = 4 to n = 3 involves a smaller energy difference than the other transitions given, resulting in the longest wavelength for the emitted photon.
Therefore, the correct answer is option d, n = 4 to n = 3.
Learn more about Rydberg constant :
https://brainly.com/question/17753747
#SPJ4
Give, and identify, the 1,2 and 1,4 products of the following reactions. for each circle the thermodynamic product.(3pts) O H-BrO CI2_CH2CI2O CH2 H-Br
Kinetic Versus Thermodynamic Control Furthermore of HBr to Dienes: 1,2-and 1,4-Addition
In the present post we'll talk about 1,2-and 1,4-Addition to dienes - specifically, the expansion of solid corrosive like HBr.
When a diene goes through response with a solid corrosive like HBr, protonation brings about a reverberation settled carbocation
The reverberation settled carbocation can go through assault at two potential positions.
At the point when the response is led at low temperatures, the response is irreversible and the significant item will be the one with the least energy change state, which is the carbon best ready to balance out certain charge.
This is alluded to as running the response under kinetic control.
At the point when the response is directed at higher temperatures, the response is reversible and the significant item will be the one which is generally thermodynamically steady, which is by and large the most-subbed alkene.
This is alluded to as running the response under thermodynamic control.
to know more about thermodynamic click here:
https://brainly.com/question/13059309
#SPJ4
which of the following is a false statement concerning amino groups?group of answer choicesthey are basic in ph.they are nonpolar.they contain nitrogen.they are found in amino acids.
The false statement concerning amino groups are nonpolar.
What is meant by amino groups?Nitrogen and hydrogen are the two components that make up an amino group. The chemical composition of an amino group is NH2. A single covalent link holds the N-H atoms in this functional group together.
Amines are substances and functional groups in chemistry that have a nitrogen atom that is basic and has a lone pair. Amines are technically ammonia derivatives in which one or more hydrogen atoms have been swapped out for a substituent, like an alkyl or aryl group.
A specific kind of functional group called an amino group is made up of one nitrogen and two hydrogens that are joined by a single covalent link. The chemical structure of the amino group is NH2.
Therefore, the correct answer is option D) They are nonpolar.
The complete question is;
Which of the following is a false statement concerning amino groups?
A) They are basic in pH.
B) They are found in amino acids.
C) They contain nitrogen.
D) They are nonpolar.
E) They are components of urea.
To learn more about amino groups refer to:
https://brainly.com/question/1302816
#SPJ4
The mass of the empty Erlenmeyer flask is 232.7 g. When filled with sodium chloride solution (density = 1.744 g/mL), the flask's mass is 428.6 g. What volume, in mL, of sodium chloride solution does the flask hold? Report the answer to one place after the decimal. Do not include the units.
The volume of the sodium chloride solution in the flask is 112.3 mL.
To find the volume of the sodium chloride solution in the Erlenmeyer flask, we first need to find the mass of the solution. We can do this by subtracting the mass of the empty flask from the mass of the filled flask:
Mass of solution = 428.6 g - 232.7 g = 195.9 g
Next, we can use the density of the solution to find the volume.
Density is defined as mass divided by volume, so we can rearrange the equation to solve for volume:
Volume = Mass / Density = 195.9 g / 1.744 g/mL = 112.3 mL
Finally, we can round our answer to one place after the decimal:
Volume = 112.3 mL ≈ 112.3 mL
So the volume of the sodium chloride solution in the flask is 112.3 mL.
To know more about volumes, refer here:
https://brainly.com/question/952755#
#SPJ11
Why is molecular polarity important for life?
Molecular polarity is important for life because it plays a crucial role in many biological processes.
What is molecular polarity?Molecular polarity refers to the distribution of electrical charge within a molecule. It is a property that results from differences in the electronegativity of the atoms in a molecule.
Molecular polarity is important for life because many biological molecules, including proteins, DNA, and carbohydrates, are polar, meaning they have regions of positive and negative charge.
This allows them to interact with other polar molecules, such as water, through hydrogen bonding, which helps to stabilize their structures and maintain their functionalities.
More on molecular polarity can be found here: https://brainly.com/question/4248472
#SPJ1
Calculate the percent by mass of the solute in the following solution: 4.10 g of toluene in 29.0 g of benzene.
The percent by mass of the solute (toluene) in the solution is 12.4%.
To calculate the percent by mass of the solute in a solution, you need to divide the mass of the solute by the mass of the entire solution and multiply by 100%.
In this case, the solute is 4.10 g of toluene, and the solvent is 29.0 g of benzene. Therefore, the mass of the entire solution is:
4.10 g (toluene) + 29.0 g (benzene) = 33.1 g
Now we can calculate the percent by mass of the solute:
(4.10 g / 33.1 g) x 100% = 12.4%
Therefore, the percent by mass of the solute (toluene) in the solution is 12.4%.
To know more about solute here
https://brainly.com/question/30620786
#SPJ4
The reaction 2A + B → C has the following proposed mechanism Step 1: A + B ⇄ D (fast equilibrium) Step 2: D + B → E slow Step 3: E + A → C + B fast The rate law consistent with this mechanism is:
Rate = k[A][B]^2
Rate = k[A]^2[B]
Rate = k[A][B]
Rate = k[A]^2[B]^2
The rate law consistent with this mechanism is Rate = k[A][B]. Thus, option C is correct.
What is rate law of chemical equation?An expression that establishes a connection between the rate of a reaction and the concentrations of the reactants involved is known as the rate law (also known as the rate equation) for a chemical reaction.
It is significant to remember that the rate law's expression for a particular reaction can only be discovered through experimentation. From the balanced chemical equation, the rate law expression cannot be obtained (since the partial orders of the reactants are not necessarily equal to the stoichiometric coefficients).
The step that determines the overall speed (rate) of a chemical reaction is the step that moves the slowest.
Therefore, Rate = k[A][B] is the law consistent with this mechanism.
To learn more about Chemical Kinetics click given link;
brainly.com/question/29735982
#SPJ4
A 2.540 g sample of an oxide of tin was heated in the air until the mass of the sample no longer
changed, and 2.842 g of tin (IV) oxide (SnO₂) was obtained as a result of the heating.
Work through the following questions. You only will be asked to submit your answers to some of
them, but you may need to calculate all of the answers a) - f) to determine the final answer g).
a) What is the mass percent of tin in SnO₂?
b) What is the mass of tin in the final sample?
c) What was the mass of tin in the original sample?
d) What was the mass of oxygen in the original sample?
e) What was the number of moles of tin in the original sample?
f) What was the number of moles of oxygen in the original sample?
g) What is the formula (SnxOy) of the original oxide of tin?
Answer:
A) The molar mass of SnO₂ is 150.71 g/mol (118.71 g/mol for Sn and 32 g/mol for O). The mass percent of tin in SnO₂ is (118.71 g/mol / 150.71 g/mol) × 100% = 78.76%.
B) The mass of tin in the final sample is 2.842 g.
C) Let x be the mass of tin in the original sample. The mass of oxygen in the original sample is (2.540 g - x). Since tin is oxidized to SnO₂, we can write the equation: Sn + O₂ → SnO₂. The molar ratio of Sn to SnO₂ is 1:1, so the number of moles of Sn in the original sample is the same as the number of moles of SnO₂ in the final sample. Using this, we can set up the following equation:
x / 118.71 g/mol = 2.842 g / 150.71 g/mol
Solving for x, we get x = 1.727 g.
Therefore, the mass of tin in the original sample is 1.727 g, and the mass of oxygen in the original sample is (2.540 g - 1.727 g) = 0.813 g.
D) The mass of oxygen in the original sample is 0.813 g.
E) The number of moles of tin in the original sample is 1.727 g / 118.71 g/mol = 0.0146 mol.
F) The number of moles of oxygen in the original sample is 0.813 g / 32 g/mol = 0.0254 mol.
G) The ratio of tin to oxygen in the original sample can be calculated by dividing the number of moles of tin and oxygen by the smallest of the two:
tin: 0.0146 mol / 0.0146 mol = 1
oxygen: 0.0254 mol / 0.0146 mol ≈ 1.74
We can round this to the nearest whole number, giving a ratio of 1:2. Therefore, the empirical formula of the original oxide of tin is SnO₂.
a solution is prepared by mixing 10.5 g of nacl (molar mass 58.44 g/mol) with 147 g of h2o (molar mass 18.02 g/mol). the final volume of the solution is 150 ml. which of the following options are the correct values for molarity (m) and molality (m) of the solution? select all that apply.
m = 0.180 mol/0.147 kg = 1.22 m m 0.180 mol/ 0.150 L = 1.20 m
m = 0.180 mol/ 0.158 kg = 1.14 m
moles NaCl = 0.180 mol
The appropriate values for the solution's molality and molarity are:
M is 1.20 M, while m is 1.22 M.
We must first determine how many moles of NaCl are present in the solution:
Moles of NaCl are equal to the mass of NaCl divided by its molar mass, which is 10.5 g/58.44 g/mol, or 0.180 mol.
We must divide the number of moles of NaCl by the litres of the solution's volume to determine its molarity:
Molarity (M) is equal to moles of NaCl per litre of solution.
1.20 M = 0.180 mol/0.150 L molarity (M)
We must divide the number of moles of NaCl by the kilogramme mass of the solvent (water) in order to determine the molality of the solution:
moles of NaCl/mass of solvent in kg molality (m) = 0.180 mol/0.147 kg 1.22 m mass of H2O = 147 g = 0.147 kg
Hence, the appropriate values for the solution's molality and molarity are:
M is 1.20 M, while m is 1.22 M.
Learn more about molarity here:
https://brainly.com/question/8732513
#SPJ4
importance of PH in Pharmactical Practices
pH affects the solubility of the molecule, which determines the stability of pharmaceuticals, the biological tolerability of the formulation, and the activity of the molecule, pH is a crucial element for all drugs manufactured in aqueous liquid forms.
Why pH is important ?A solution's pH is a significant indicator of its chemical composition. The pH may impact how readily available nutrients are, how biological processes work, how bacteria behave, and how chemicals behave.
The negative base-10 log of the hydronium ion concentration in a solution is the usual definition of pH value.
In the pharmaceutical sector, we're accustomed to concentrations of little more than 1M under typical circumstances. That being stated, the pH value in that situation may be between two extremes.
Thus, pH is important in Pharmaceutical Practices.
To learn more about the pH, follow the link;
https://brainly.com/question/15289741
#SPJ9
Practice
If G = green and g = purple, how many offspring will be
purple if the parents' genotypes are gg and
In the text boxes, write the percentage of offspring that is green and
the percentage that is purple.
6GB
g g
Gg
G Gg
ggggg
Green
Purple
The percentage of purple offspring and green offspring are 25% and 25% respectively.
What is offspring?Offspring are living creatures' young creations, generated either from a single organism as well as, inside the event of sexual reproduction, by two organisms. In a broader sense, collective children may be referred to by the term brood or progeny.
This can apply to a group of children born at the same time, such as chicks hatching from a single clutch of eggs, or to the entire offspring, as in the case of the honeybee.
purple offspring = 25%
green offspring = 25%
Therefore, the percentage of purple offspring and green offspring are 25% and 25% respectively.
To learn more about offspring, here:
https://brainly.com/question/10021635
#SPJ9
Your question is incomplete but most probably your full question was,
If G = green and g = purple, how many offspring will be purple if the parents' genotypes are gg and write the percentage of offspring that is green and the percentage that is purple. 25%, 35%,45%
When a solution is diluted, the O concentration of solute remains unchangcd O volume of solution rcmains unchanged O amount of solvent remains unchanged O amount of solute remains unchanged
When a solution is diluted, the volume of the solution increases, while the amount of solvent remains unchanged. Option c is the correct answer.
When a solution is diluted, the concentration of solute decreases, while the amount of solute remains unchanged. This is because the amount of solute dissolved in the solution does not change when additional solvent is added, but the volume of the solution increases.
As a result, the concentration of the solute in the solution decreases. The volume of the solution increases, while the amount of solvent remains unchanged.
To know more about the solvent, here
brainly.com/question/15212814
#SPJ4
--The complete answer is, When a solution is diluted, the
a. concentration of solute remains unchanged
b. volume of solution remains unchanged
c. amount of solvent remains unchanged
d. amount of solute remains unchanged--
on a t-v diagram, the region under the dome area between the saturated liquid and saturated vapor lines is known as the ____ region.
saturated liquid vapor aka liquid-vapor mixture. A mixture of saturated vapor and liquid is present in this condition. The dryness fraction, a parameter that describes the characteristics of water in this phase, must be calculated is combined with the saturation characteristics.
What is vapor pressure?Vapor pressure is the pressure exerted by a vapor when it is in equilibrium with its liquid or solid phase at a given temperature. It is a measure of the tendency of a substance to evaporate and is a function of the temperature and the strength of the intermolecular forces between the molecules of the substance. At any given temperature, a substance will have a specific vapor pressure. When the vapor pressure of the substance is equal to the external pressure, the substance will begin to boil or evaporate. The vapor pressure of a substance increases with increasing temperature, as the average kinetic energy of the molecules increases and more molecules can escape from the liquid or solid phase and enter the gas phase.
To learn more about vapor pressure, click the link below ;
brainly.com/question/2693029
#SPJ4
for each compound, select all the descriptions that apply. compound a: an alkene is bonded to a triple bond. compound a is: conjugated a diene a triene nonconjugated compound b: three alkenes. alkenes 1 and 2 are bonded together via a single bond. alkenes 2 and 3 are bonded together via a single bond. compound b is: conjugated nonconjugated a diene a triene compound c: two triple bonds are bonded together via a c h 2 group. compound c is: nonconjugated a diene a triene conjugated compound d: an akene is bonded to a carbonyl which is bonded to a methyl group. compound d is: a diene conjugated nonconjugated a triene
Consequently, each of the following compounds is conjugated with a diene: compound a; conjugated with a trine; compound c; and conjugated with a diene: compound d.
Why is CH3 called methyl?When one hydrogen atom is taken out of an alkane, a group of atoms known as an alkyl group is created. The group is given a name by changing the parent hydrocarbon's -ane suffix to -yl. For instance, the -CH3 group, which is also known as a methyl group, is created when one hydrogen atom is removed from methane (CH4). In organic chemistry, a methyl group is an alkyl produced from methane that has the chemical formula CH3, one carbon atom bound to three hydrogen atoms. The group's name is frequently shortened to Me in formulas. In numerous organic molecules, this hydrocarbon group can be found. In most compounds, the group is extremely stable.
What is a methyl and ethyl?Methyl has a carbon atom and three hydrogen atoms, whereas ethyl has two carbon atoms and five hydrogen atoms. As a result, the ethyl group has a higher molar mass than the methyl group. Alkane ethane is the source of methyl, while alkane methane is the source of ethyl. 3-Methylpentane is the IUPAC name for the substance in question. It has a lengthy chain of 5 carbon atoms, which gives it the prefix pent-, and a single bond is what gives it the postfix -ane (alkane). Given that the methyl group is present at the third carbon, it is 3-methylpentane.
To know more about Methyl and Ethyl visit:
https://brainly.com/question/29589700
#SPJ4
Which of the following properties is associated with the value of the n quantum number?
A) the number of electrons in an orbital
B) the size of an orbital
C) the orientation in space of an orbital
D) the energy of an orbital
E) the shape of an orbital
The correct answer is B) the size of an orbital.
The n quantum number, also known as the principal quantum number, is an integer value that determines the energy level and size of an orbital in an atom. The value of n ranges from 1 to infinity, with higher values of n corresponding to higher energy levels and larger orbitals.
The size of an orbital is determined by the distance between the electron and the nucleus. As the value of n increases, the distance between the electron and the nucleus increases, and the size of the orbital increases as well. This means that orbitals with higher values of n have more volume and can hold more electrons.
The other quantum numbers are associated with other properties of the electron orbitals. The l quantum number is associated with the shape of an orbital, the m quantum number is associated with the orientation of an orbital in space, and the spin quantum number is associated with the spin of an electron.
To learn more about Orbitals :
https://brainly.com/question/23160372
#SPJ4
1995 D Two reactions are represented above. The potential energy diagram for reaction 1 is shown. The potential energy of the reactants in reaction 2 is also indicated on the diagram. Reaction 2 is endothermic, and the activation energy of reaction 1 is greater than that of reaction 2.
The diagram shows the potential energy of both reactions. The reactants of reaction 1 have a lower potential energy than those of reaction 2, indicated by the lower starting point on the graph.
What is potential?Potential is the capacity or ability to become or develop into something in the future. It can refer to physical, mental, or spiritual power and potential. Potential is often seen as untapped or unused and can be developed through effort and determination. Potential is also seen as the ability for growth and development, and the potential for a person or thing to reach its fullest potential. Potential can be seen as the capacity to do something, even if it has yet to be realized. It is often seen as a measure of one's potential for future success or achievement.
Reaction 1 has a higher activation energy, indicated by the greater distance between the reactants and products. This means that reaction 1 requires more energy to proceed than reaction 2, making it an endothermic reaction.
To learn more about potential
https://brainly.com/question/14427111
#SPJ1
What mass of ice (in g) can be melted if 24.9 kJ of thermal energy are added at the freezing point? Use molar mass = 18.02 g/mol
The answer is approximately 1332.75 g of ice can be melted if 24.9 kJ of thermal energy are added at the freezing point.
What is thermal energy?
Thermal energy refers to the energy contained within a system that is responsible for its temperature.
The heat required to melt a substance is equal to the enthalpy of fusion of that substance times its mass. The molar enthalpy of fusion of ice is 333.55 J/mol, so the amount of heat required to melt 1 mol of ice is 333.55 J.
To find the mass of ice that can be melted with 24.9 kJ of thermal energy, we first need to convert the energy from kJ to J:
24.9 kJ = 24.9 x 10^3 J = 24900 J
Next, we divide the amount of thermal energy by the molar enthalpy of fusion of ice to find the number of moles of ice that can be melted:
24900 J / 333.55 J/mol = 74.22 mol
Finally, we multiply the number of moles of ice by its molar mass to find the mass of ice in grams:
74.22 mol x 18.02 g/mol = 1332.75 g
Therefore, The answer is approximately 1332.75 g of ice can be melted if 24.9 kJ of thermal energy are added at the freezing point.
Learn more about thermal energy here: brainly.com/question/934320
#SPJ1
Select factors that will change when additional A is added...Select the factors that will change when additional A is added to a system at equilibrium. Select the factors that will change when additional A(g) is added to the following system at equilibrium. Overall Reaction: A(g) + B(g) 2C(g)
When additional A(g) is added to the following system at equilibrium, the actors that will change are pressure, temperature, reaction rate and concentration.
Concentrations of A, B, and C: The concentration of A will increase, while the concentrations of B and C will decrease. The extent of the changes will depend on the stoichiometry of the reaction and the equilibrium constant.
Pressure: The addition of A(g) will increase the pressure of the system, assuming the volume is constant. This may cause a shift in the equilibrium position to favor the side with fewer moles of gas, which in this case is the reactant side.
Temperature: The addition of A(g) may cause a temperature change in the system. If the reaction is exothermic, the addition of A(g) will increase the temperature of the system and may cause a shift in the equilibrium position to favor the reactants. If the reaction is endothermic, the addition of A(g) will decrease the temperature of the system and may cause a shift in the equilibrium position to favor the products.
Reaction rate: The addition of A(g) may temporarily increase the rate of the forward reaction, but the system will eventually reach a new equilibrium position with the same equilibrium constant.
To know more about equilibrium here
https://brainly.com/question/11336012
#SPJ4
An aqueous solution of Ca(OH)2 at 25 oC has a pH of 12.4. Assume Ca(OH)2 fully dissociates. Calculate the concentration (in M) of Ca(OH)2. Report to 3 decimal places.
Answer:
the first one may be more complex so the second one will be simplified :)
Explanation:
A 400 mL sample of a 0.100 M formate buffer, pH 3.75, is treated with 6 mL of 1.00 M KOH. What is the pH following this addition? (pKa for formic acid is 3.75)
Express your answer to two decimal places.
The pH of A 400 mL sample of a 0.100 M formate buffer, pH 3.75, is treated with 6 mL of 1.00 M KOH is 4.88
pH buffer = 3.75
pKa for formic acid is 3.75
Using Henderson-Hasselbalch equation for formate buffer:
pH = pKa + log [ HCOO⁻]
[HCOOH]
Input values in above equation
3.75 = 3.75 + log [ HCOO⁻]
[HCOOH]
log [ HCOO⁻] = 0
[HCOOH]
[ HCOO⁻] = 1
[HCOOH]
[ HCOO⁻] = [HCOOH]
Concentration of formate buffer = 0.100 M
[ HCOO⁻] - [HCOOH] = 0.100 M
[ HCOO⁻] = [HCOOH] = 0.05 M
As a result, the buffer's volume is the same. As a result, the concentration is calculated as the number of moles of both formate ions and formic acid.
Then we should calculate the number of moles for given molarity
Molarity of solution = moles of solute x 1000
volume of solution in mL
1M KOH = moles of KOH x 1000 = 0.006 moles
6 mL
The chemical reaction for formic acid and KOH follows the equation:
HCOOH +KOH ⇒ HCOO⁻ +H₂O
initial 0.05 0.006 0.05
final 0.041 - 0.056
Volume of solution = 400 + 6 = 406 mL = 0.406 L
We use the Henderson Hasselbalch equation to determine an acidic buffer's pH:
pH = pKa + log [ HCOO⁻]
[HCOOH]
[ HCOO⁻] = 0.056 =
0.406
[ HCOOH] = 0.041
0.406
pH = 3.75 + log [ HCOO⁻]
[HCOOH]
pH = 3.75+ log [0.056/ 0.406]
[ 0.041/ 0.406]
pH = 4.88
Learn more about pH at https://brainly.com/question/19554913
#SPJ4
An open manometer is filled with mercury and
connected to a container of hydrogen. The
mercury level is 78.0 mm higher in the arm of the
tube connected to the air. Air pressure is
100.7 kPa. What is the pressure of the hydrogen in kilopascals?
Does anyone know what the container pressure would be? and how do I solve this?
Answer:
The pressure of the hydrogen in the container can be determined by using the equation:
P_H2 + ρgh = P_air
where P_H2 is the pressure of the hydrogen, ρ is the density of mercury (13,600 kg/m^3), g is the acceleration due to gravity (9.8 m/s^2), and h is the height difference between the mercury levels in the two arms of the manometer.
First, we need to convert the height difference from millimeters to meters:
h = 78.0 mm = 0.078 m
Next, we can substitute the given values into the equation:
P_H2 + (13,600 kg/m^3)(9.8 m/s^2)(0.078 m) = 100.7 kPa
Solving for P_H2, we get:
P_H2 = 100.7 kPa - (13,600 kg/m^3)(9.8 m/s^2)(0.078 m)
P_H2 = 99.0 kPa
Therefore, the pressure of the hydrogen in the container is 99.0 kPa
Understanding how electrostatic energy scales with churns separation
The process describing how how electrostatic energy scales with churns separation is given above.
What is electrostatic energy?Electrical potential energy is typically stored by separating oppositely-charged particles and storing them on different conductors
Given is to understand how electrostatic energy scales with churns separation.
Churning is the process of shaking milk in order to convert it to butter. It is used to extract butter from milk or curd. It is also used to churn butter from cream.The separation of particulates in a fluid can be efficiently accomplished using electrical forces, the main criterion being the fluid must have insulating properties so an electric field can be superimposed across it.Electrostatic separation is done by initially charging the particulates or contaminants and then moving and concentrating them at the electric field boundary.Industrial Electrostatic Precipitation - In industrial applications, there are generally two arrangements:The horizontal-flow plate type - where a series of parallel plates, spaced up to 400 mm, form the gas passages and the discharge electrodes are insulated and hanging centrally between them.The tube type precipitator -where the gases pass upwards through vertical tubes measuring up to 250 mm dia., with the discharge electrode taking the form of a coaxial element.Therefore, the process describing how how electrostatic energy scales with churns separation is given above.
To solve more questions on electrostatic energy scaling, visit the link-
brainly.com/question/29014197
#SPJ1
FILL IN THE BLANK. The cations found in seawater originally came from ____, whereas the anions originated from ____.
The ions such as the cations found in seawater originally came from Earth's crust whereas the anions originated from Earth's mantle.
What are ions?An ion is defined as an atom or a molecule which has a net electrical charge. There are 2 types of ions :1) cation 2) anion . The cation is the positively charged ion and anion is the negatively charged ion . As they are oppositely charged they attract each resulting in the formation of ionic bond.
Ions consisting of single atom are mono-atomic ions while which consists of two or more ions are called as poly-atomic ions . They are created by chemical interactions .
Learn more about ions,here:
https://brainly.com/question/1447156
#SPJ1
Compare the water hardness of the following three solutions as mg of calcium ions in 1 liter of water and answer the following questions: Solution A: 25 mg Solution B: 100 mg Solution C: 200 mg -According to the water hardness labels from EPA, Solution B is considered as ✓ [ Select ] very hard hard soft moderately hard < Et to see the highest conductivity value? [Select] Compare the water hardness of the following three solutions as mg of calcium ions in 1 liter of water and answer the following questions: Solution A: 25 mg Solution B: 100 mg Solution C: 200 mg - According to the water hardness labels from EPA, Solution B is considered as [ Select] -Which solution will you expect to see the highest conductivity value [Select ] Solution B Solution All solutions should be the same Solution
The solution C has the highest water hardness, measured in milligrammes of calcium ions per litre of water.
Soft water is defined as having a calcium ion level lower than 60 mg/L. And if this occurs between 60 mg/L and 120 mg/L, it is considered moderately hard, between 120 mg/L and 180 mg/L, it is considered hard, and over 180 mg/L, it is considered very hard.
1. Since solution B contains 100 mg, it will be considered MODERATELY HARD.
2. Generally speaking, the conductivity value increases with ion concentration in a solution. Calcium ion concentration is thus highest in solution C. So the answer will be SOLUTION C.
Water hardness is a measure of the amount of dissolved minerals, such as calcium and magnesium, in water. Hard water can cause problems with soap lathering, scaling, and corrosion in pipes and appliances.
Learn more about water hardness here:
https://brainly.com/question/13161362
#SPJ4
I need to mark the steepest areas.
The hilltops and the steepest point of a slope are found in the highest and most closely-spaced contour lines on the map.
What are contour lines?Contour lines are lines on a map that connect points of equal elevation. Each contour line represents a specific elevation, and the spacing between contour lines represents the slope of the terrain.
The closer the contour lines are to each other, the steeper the slope. The hilltops are found where the contour lines form a closed circle or oval shape. The steepest point of a slope is found where the contour lines are closest together, indicating the highest rate of change in elevation.
Learn more about contour lines at: https://brainly.com/question/13088900
#SPJ1
synthesis of dihydropyran dihydropyran is synthesized by treating tetrahydrofurfuryl alcohol with an arenesulfonic acid, arso3h. draw curved arrows to show the movement of electrons in this step of the reaction mechanism.
The creation of dihydropyran Tetrahydrofurfuryl alcohol is converted into dihydropyran by reacting it with the arenesulfonic acid arso3h.
Here's the reaction mechanism for the synthesis of dihydropyran from tetrahydrofurfuryl alcohol and arylsulfonic acid:
First, the acid protonates the alcohol to make it a better leaving group:
OH-CH2CH2CH2CH2-OH + ArSO3H → OH2+-CH2CH2CH2CH2-OH + ArSO3-
The product is then deprotonated by a base, such as sodium methoxide, to form dihydropyran:
[OC(CH2)2-Ar]+SO3- + NaOCH3 → OC(CH2)2-Ar + NaSO4CH3-
Overall, the reaction can be represented as:
OH-CH2CH2CH2CH2-OH + ArSO3H → dihydropyran + NaSO4CH3-
Learn more about movement of electrons here:
https://brainly.com/question/11905668
#SPJ4
which of the following macromolecules are characteristically water-insoluble?group of answer choicesproteinslipidscarbohydrates
The macromolecules that are characteristically water insoluble is the correct option is lipids.
The macromolecule are the molecule that are extraordinarily large. They may be organic materials such as the sugars and the natural fibers or the synthetic materials such as the plastics, the synthetic fibers, Lipids, the proteins, the nucleic, and carbohydrates . The lipids are water hating. They are water insoluble.
The lipids are the non polar compound and the water is the polar compound. The polar will dissolve the polar compounds and the non polar will dissolves the non polar compound. Therefore the lipids are insoluble in the water.
To learn more about lipids here
https://brainly.com/question/3498396
#SPJ4