Answer:
Explanation:
if you are pulling in the positive direction and Upward is also positive.
F = -0.96i + 0.58(9.8)j
F = -0.96i + 5.7j
F = √(-0.96² + 5.7²) = 5.8 N
You are pulling a sled with constant velocity by using a rope then the surface force the ground exerts on the sled will be 5.8 N.
What is tension?The pulling force conveyed axially by a string, cable, chain, or another analogous object, or by either end of a rod, truss member, or another such three-dimensional object, is referred to as tension in physics. Another way to think of tension is as the action-reaction pair of forces acting at each end of the previous elements. Perhaps tension is the polar opposite of compression.
A restoring force may cause what is also referred to as tension when atoms or molecules are torn apart from one another at the atomic level and build up potential energy.
If you are moving upward and pushing in a positive way,
F = -0.96 i + 0.58(9.8) j
F = -0.96 i + 5.7 j
F = [tex]\sqrt{(-0.96^2 + 5.7^2)}[/tex]
F= 5.8 N
To get more information about Tension :
https://brainly.com/question/15880959
#SPJ5
n earthquake emits both P-waves and S-waves that travel at different speeds through the Earth. A P-wave travels at 9 000 m/s and an S-wave at 4 000 m/s. If P-waves are received at a seismic station 34.0 s before an S-wave arrives, how far is the station from the earthquake center
Answer:
Yes , i also need answer
Explanation:
n earthquake emits both P-waves and S-waves that travel at different speeds through the Earth. A P-wave travels at 9 000 m/s and an S-wave at 4 000 m/s. If P-waves are received at a seismic station 34.0 s before an S-wave arrives, how far is the station from the earthquake center
Which is the independent variable in the graph of the U.S. population 1800-1900?
1. United States
2. straight lines
3. years
4. population
Answer:
3. years
Explanation:
The independent variable is the x axis of graph
How do I solve this problem
Answer:
it is light
Explanation:
the arrow that says light is on the glass it must be near from tungsten
when the tides are especially weak it is called a _____ tide
Answer:
When the tides are especially weak, it is called a NEAP tide.
Explanation:
Hope this helps :)
Answer:
Neap
Explanation:
Answered!
Below are three graphs. The shape of graph 3 shows that the current flowing through this component is __________ proportional to the potential difference across it. What one word completes the sentence?
The relationship between variables might be either directly porportional to each other or inversely proportional to each other. For instance, the current flowing is _directly_ proportional to the potential difference across it.
---------------------
Since I do not have the graph, I will propose two potential options and I will describe each of them.
I suggest you to choose the one that matches the shape of graph 3.
GraphsProbably your graph is composed of the X and Y axes, perpendicularly placed, in a way in which four quadrants are formed.You might see that one of the axes represents the current (I), and the other one represents the potential difference (V).
And a straight line that represents the relationship between the current and the potential difference.
The direction of the straight line reflects the relationship between variables.The change on each variable is proportional to the change on the other variable. Now we have to analyze how that change occurs. Option 1
The current flowing through this component is __DIRECTLY__ proportional to the potential difference across it.
If this is the case of your graph, you should see the straight line crossing from the left inferior quadrant to the right superior one.
The direction of the line suggests that one of the variables increases as the other one increases too. The current increases as the potential increases.
This is the case of the Ohm's law.
Option 2The current flowing through this component is __INVERSELY__ proportional to the potential difference across it.
If this is the case of your graph, you should see the straight line crossing the right quadrant from the superior left corner to the inferior right one.
The direction of the line suggests that the variable represented in the Y ax decreases as the other one increases.
For instance, The current decreases as the potential increases. Or the potential decreases as the current increases.
In the attached files you will find graphs of both options.
-------------------------
You can learn more about the Ohm's law at
https://brainly.com/question/17286882?referrer=searchResults
You can learn more about the relationship between variables at
https://brainly.com/question/16937826?referrer=searchResults
https://brainly.com/question/21627823?referrer=searchResults
Answer: The relationship between variables might be either directly proportional to each other or inversely proportional to each other. For instance, the current flowing is directly proportional to the potential difference across it.
Explanation:
A car accelerating from rest for 20s to reach velocity of 15 m/s and it keeps on. moving with this velocity for 50s an then it applied the break
Stop in 30s what is the displacement?
WILL GIVE BRAINLY best answer with steps
Answer:
1125m
Explanation:
The car moves with a uniformly accelerated motion for 20s:
s = 1/2·a·t² + v0·t + s0 (note that vo = 0 and s0 = 0, with v0 being the initial velocity and s0 the initial displacement).
So: s = 1/2·a·t²
The acceleration will be: Δv/Δt = 15m/s / 20s = 0.75 m/s²
s1 = 1/2·0.75 m/s² · (20 s)^2 = 150m
Then it continues with the velocity he acquired (v = a·t = 0.75 m/s²·20s = 15 m/s):
s2 = vt = 15m/s·50s = 750m
The final acceleration, when stopping, will be:
a = Δv/Δt = -15m/s / 30s = -1/2 m/s²
s3 = 1/2·(1/2m/s²)·(30s)² = 225m.
Now we sum s1 with s2 and s3:
s1 + s2 + s3 = 150m + 225m + 750m = 1125m
Which type of muscle cell can have multiple nuclei
Answer:
Skeletal Muscle cells
Skeletal muscle cells are long, cylindrical, and striated. They are multi-nucleated meaning that they have more than one nucleus. This is because they are formed from the fusion of embryonic myoblasts.
Answer:
skeletal muscle cells can have multiple nuclei
Explanation:
This is because they are formed from the fusion of embryonic myoblasts.
The diagram shows the tropic levels in a lake in a farm. Suppose the farmer sprays a field with a chemical fertilizer. Based on the flow of energy in the lake, which organisms would contain the highest concentration of the chemical fertilizer?
Based on the flow of energy that's in the lake, it can be deduced that the diatoms and algae will have the highest concentration.
Energy flow refers to the flow of energy through living organisms that are within an ecosystem. Energy is passed from one trophic level to the next trophic level.
If the farmer sprays a field with chemical fertilizer, the organism that would contain the highest concentration of the chemical fertilizer are diatoms and algae since they're at the bottom of the ecosystem.
Learn more about energy flow on:
https://brainly.com/question/2116310
Determine the rTo understand the concept of nodes of a standing wave.
The nodes of a standing wave are points where the displacement of the wave is zero at all times. Nodes are important for matching boundary conditions, for example that the point at which a string is tied to a support has zero displacement at all times (i.e., the point of attachment does not move).
Consider a standing wave, where y represents the transverse displacement of a string that extends along the x direction. Here is a common mathematical form for such a wave:
y(x,t)=Acos(kx)sin(ωt),
where A is the maximum transverse displacement of the string (the amplitude of the wave), which is assumed to be nonzero, k is the wavenumber, ω is the angular frequency of the wave, and t is time.
Part A
Which one of the following statements about wave y(x,t) is correct?
adius of the 236U nucleus.
Answer:
The nodes of a standing wave are points where the displacement of the wave is zero at all times nodes are important for matching boundary conditions for example that the point at which a string is tied to a support has zero displacement at all times ie the point of attachment does not move consider a standing
how big is earth
today
Answer:
3,958.8 mi
Explanation:
The earth has a mass of 5.972 x 1024 Kg. You decide to
put the satellite in an orbit 400 Km above the surface of the earth which has a radius of 6,371 Km, so the total
distance from the center of the earth to the satellite is 6,771,000 m. What will you need the velocity of the
satellite to be to stay in orbit? Show your work
Answer:
Explanation:
You want the required centripetal force to equal gravity force
if m is the mass of the satellite
ma = mv²/R
a = v²/R
F = ma = GMm/R²
a = GM/R²
v²/R = GM/R²
v² = GM/R
v = √(GM/R)
v = √(6.674 x 10⁻¹¹(5.972 x 10²⁴)/6.771 x 10⁶)
v = 7.672 x 10³ m/s
Two students run a race. Student A is 50 kg and runs at 5 m/s. Student B is 30 kg and runs at 2 m/s. Which
student has more Kinetic energy?
Answer:
Explanation:
KEA = ½(50)5² = 625 J
KEB = ½(30)2² = 60 J
Student A has more kinetic energy.
More than ten times more kinetic energy due to both larger mass and higher velocity.
What is the unit of frequency
Answer:
hertz (Hz)
The number of periods or cycles per second is called frequency. The SI unit for frequency is the hertz (Hz).
Answer: the answer is hertz! if you’re on plato it’s option C. have a nice day! :)
Explanation:
Ginny is snowboarding down a ski slope. Her total mass (including the snowboard) is 68.5 kg. When she reaches the bottom of the slope, she is moving at 6.55 m/s. The coefficient of friction between the snowboard and the ground is 0.088 . How fast will Ginny be moving 2 seconds after reaching the bottom of the slope?
1) 5.71 m/s
2)5.91 m/s
3)4.82 m/s
4)4.08 m/s
Answer:
Explanation:
Assuming the run out at the bottom of the slope is horizontal
μ = Ff/N = Ff/mg
Ff = μmg
a = Ff/m = μmg/m = μg
v = u + at
v = u + μgt
v = 6.55 - 0.088(9.81)(2)
v = 4.82 m/s
After reaching the bottom of the slope, it will take a speed of 4.8m/s to reach. So, the correct option is (C).
What is Friction?Friction is the force which opposes the relative motion of solid surfaces, fluid layers, and material elements that are sliding against each other. There are many types of friction like
Dry frictionFluid frictionLubricated friction Skin friction Internal frictionFriction can be expressed as
Ff = μFN
where, Ff is the force of friction (N)
μ is the coefficient of friction.
FN is the normal force
As per the above equation, it is actually the normal force, not the weight, which is responsible for friction.
For given information,
Assuming the bottom of the slope is horizontal
So, μ = Ff/N = Ff/mg
Ff = μmg
a = Ff/m = μmg/m = μg
v = u + at (u- initial speed, v= final speed, a= acceleration and t= time)
v = u + μgt (g= acceleration due to gravity)
u = 6.55 - 0.088(9.81)(2)
u = 4.82 m/s
Thus, after reaching the bottom of the slope, it will take a speed of 4.8m/s to reach. So, the correct option is (C).
Learn more about Friction, here:
https://brainly.com/question/13000653
#SPJ2
You have a pendulum clock made from a uniform rod of mass M and length L pivoting around one end of the rod. Its frequency is 1 radian/sec. The pivot breaks. Though the mass change is negligible, you need to rehang the rod halfway between the old pivot point and the middle of the rod. The new oscillation frequency is:
A. 0.88 rad/sec
B. 1.13 rad/sec
C. 1.07 rad/sec
D. 0.92 rad/sec
The new oscillation frequency of the pendulum clock is 1.14 rad/s.
The given parameters;
Mass of the pendulum, = M Length of the pendulum, = LInitial angular speed, [tex]\omega _i[/tex] = 1 rad/sThe moment of inertia of the rod about the end is given as;
[tex]I_i = \frac{1}{3} ML^2[/tex]
The moment of inertia of the rod between the middle and the end is calculated as;
[tex]I_f = \int\limits^L_{L/2} {r^2\frac{M}{L} } \, dr = \frac{M}{3L} [r^3]^L_{L/2} = \frac{M}{3L} [L^3 - \frac{L^3}{8} ] = \frac{M}{3L} [\frac{7L^3}{8} ]= \frac{7ML^2}{24}[/tex]
Apply the principle of conservation of angular momentum as shown below;
[tex]I _i \omega _i = I _f \omega _f\\\\\frac{ML^2}{3} (1 \ rad/s)= \frac{7ML^2}{24} \times \omega _f\\\\\frac{24 \times ML^2}{3 \times 7 ML^2} (1 \ rad/s)= \omega _f\\\\1.14 \ rad/s = \omega _f[/tex]
Thus, the new oscillation frequency of the pendulum clock is 1.14 rad/s.
Learn more about moment of inertia of uniform rod here: https://brainly.com/question/15648129
A jet is flying at a speed of 700 kilometers per hour. The pilot encounters turbulence due to a 50-kilometer- per-hour wind blowing at an angle of 47°. Find the resultant force on the plane.
Answer:
F = 0 N
Explanation:
The problem does not talk about any acceleration. We can just assume it always moves at a constant speed so the resultant force will be 0 newtons. Of course you could say that it accelerates for a certain amount of time, as the wind blows, but the problem doesn't tell us when to calculate the resultant force (if during the acceleration or after) + we don't have the mass of the jet.
2. Where do hyperbolic comets originate?
A.the Oort cloud
B.the asteroid belt
B.the Kuiper belt
C.interstellar space
Answer:
Hyperbolic comets originate from the Kuiper Belt.
An airplane accelerates from rest down a runway at 9.50 m/s2 for 29.3 seconds when it
takes off. What is the distance traveled while taking off?
Answer:
Explanation:
s = ½at²
s = ½(9.50)(29.3²) = 4,077.8275
s = 4080 m
when rounded to the three significant digits of the question numerals.
3. How much power does an electric light installation draw at 120 V if it creates a current of 0.8 amps?
O A. 32 watts
O B. 120 watts
Q C. 48 watts
D. 96 watts
Answer:D
Explanation:
R =
V
I
=
120 volt
0.8 ampere
= 150 ohm (Ω)
P = V × I
= 120 volt × 0.8 ampere
= 96 watt (W)
An electric light installation can draw Power of 96 Watt at 120 V if it creates a current of 0.8 amps
What is electric power ?Electric power is the rate of electric energy transfer by an electric circuit per unit time . It is denoted by P and measured using the SI unit of power that is Watt (W)
since, Electric Power = voltage * current
Power = 120 V * 0.8 A
Power = 96 Watts
An electric light installation can draw Power of 96 Watt at 120 V if it creates a current of 0.8 amps
learn more about Electric power
https://brainly.com/question/16925887?referrer=searchResults
#SPJ3
A 1500 kg car has the same momentum as a 2500 kg truck moving at 25 m/s. How fast is the car moving in m/s
Answer:
41.6m/s
Explanation:
P=mv
2500kg × 25m/s = 62500kgm/s
62500kgm/s ÷ 1500 kg = 41.6m/s
A gold fish weighing 13g has a speed of 8.8m/s. What is its Kinetic energy
Answer:
0.47 J
Explanation:
Energy can be changed from one form to another. Which terms can be used to describe these changes? Check all
that apply.
energy conversion
energy conservation
energy correlation
energy transformation
energy transference
Answer:
energy transformation
Answer: Energy Transformation & Energy Conversion.
The block in the figure below has a mass of 5.1 kg and it rests on an incline of angle . You pull on the rope with a force F = 34 N. Assume the incline is smooth and determine the angle of the incline if the block moves with constant speed.
42.9°
Explanation:
Let's assume that the x-axis is aligned with the incline and the positive direction is up the incline. We can then apply Newton's 2nd law as follows:
[tex]x:\;\;\;\;F - mg\sin{\theta} = 0\;\;\;\;[/tex]
[tex]\Rightarrow mg\sin{\theta} = F[/tex]
Note that the net force is zero because the block is moving with a constant speed when the angle of the incline is set at [tex]\theta.[/tex] Solving for the angle, we get
[tex]\sin{\theta} = \dfrac{F}{mg}[/tex]
or
[tex]\theta = \sin^{-1}\left(\dfrac{F}{mg}\right)[/tex]
[tex]\;\;\;= \sin^{-1}\left[\dfrac{34\:\text{N}}{(5.1\:\text{kg})(9.8\:\text{m/s}^2)}\right][/tex]
[tex]\;\;\;=42.9°[/tex]
HELP PLEASE WILL MARK BRAINLIEST
Outside wooden steps may get slippery when they are wet. How could you make them less slippery?
There are many ways you can get wooden steps to be less slippery even when they are wet. Some ways are:
*You can put a carpet on the steps. The fibers in a carpet usually have some friction which will give you a grip as you climb up and/or down and prevent you from falling.
*You can apply anti-slip coatings like a paint on the steps. If you add some sand to the paint to add traction and lessen the slippery nature. Alternatively, If the wood has been waxed, you may consider using a wax remover.
*You can fix a hand railing so that you can hold on to it when you go up and down the steps.
refers to a fear of being trapped in a crowded, public place.
Answer:
Agrophobia
Explanation:
an anxiety disorder in which someone feals anxious and scared in a public place
Which phrase describes the energy transformation that happens in a
generator?
A. Electrical energy into chemical energy
ООО
B. Electrical energy into mechanical energy
C. Chemical energy into electrical energy
O
D. Mechanical energy into electrical energy
SI
Answer:
Mechanical energy into electrical energy
Explanation:
Answer:
ExplanMechanical energy into electrical energy
SIation:
The motor in a hairdryer is attached to a 3V battery. A current of 0.8A flows through the motor for 3 minutes. Calculate the total charge in this time.
The total charge in this time is equal to 144 Coulomb.
Given the following data:
Voltage = 3 VoltsCurrent = 0.8 AmperesTime = 3 minutes.To calculate the total charge in this time:
First of all, we would convert the value of time in minutes to seconds.
Conversion:
1 minute = 60 seconds
3 minutes = 180 seconds
Formula for quantity of charge.Mathematically, the quantity of charge is given by this formula:
[tex]Q=It[/tex]
Where:
Q is the quantity of charge.I is the current.t is the time measured in seconds.Substituting the given parameters into the formula, we have;
[tex]Q = 0.8 \times 180[/tex]
Quantity of charge, Q = 144 Coulomb.
Read more on charges here: https://brainly.com/question/4313738
Answer:
960 watts
Explanation:
This is the question I need help with
Answer:
Explanation:
If we ASSUME that a CCW torque is positive
τ = 10sin135[8.0] - 16sin90[4.0] + 19sin160[3.0] = 12 N•m
as the result is positive, the net torque is CCW.
Wtz the answer to this question? I need to get it right
Answer: Next time you create a question, add an image or PDF. Because I do not know the question. So, may you please create a new question?
Select the correct answer.
What is the force that can cause two pieces of iron to attract each other?
A.
gravitational force
B.
magnetic force
C.
elastic force
D.
electrostatic force
Answer:
A. gravitational force always true.
B, C and D could be true under the correct conditions