Wind energy is increasingly relied upon to help meet global energy needs. Wind energy can be used to generate electricity using wind turbines. What best describes electricity generation using wind turbines? Axes of wind turbines can be either vertical or horizontal; there are benefits (and drawbacks) to each type.

Answers

Answer 1

Electricity generation using wind turbines involves converting the kinetic energy of wind into electrical energy. Wind turbines consist of blades that rotate when wind passes over them.

The rotation drives a shaft, which in turn powers a generator that produces electricity. The electricity generated is typically fed into the power grid, where it is distributed to consumers.

Horizontal axis wind turbines (HAWTs) are the most common type of wind turbine and have blades that rotate around a horizontal axis. HAWTs are typically more efficient than vertical-axis wind turbines (VAWTs) because they can capture more energy from the wind.

VAWTs have blades that rotate around a vertical axis and are less common. However, VAWTs can be better suited for certain applications, such as in urban areas where wind direction can be highly variable.

To learn more about Wind turbines

https://brainly.com/question/928271

#SPJ4


Related Questions

The table below provides data obtained at different geographical locations on Earth.
In which city would Earth’s gravitational field strength be the largest?

Answers

The city of Charleston, WV will have the largest gravitational field strength.

What is gravitational field strength?

The space around a material object in which its gravitational force can be experienced is known as gravitational field.

The gravitational field strength at a point in this field is the force experienced on unit mass placed at that point.

Here,

The data obtained at different geographical locations of earth are given in the table. The latitude of the geographical areas are provided.

Gravitational field strength,  I = -GM/r²

i.e, it follows the inverse square law.

The variation of gravitational field strength with change in latitude has been studied and the studies proved that:

As an  object moves away from the surface of earth, the gravitational force  between the object and earth decreases and therefore the gravitational field strength also decreases.

Therefore considering the latitudes of the geographical places mentioned, the place at the lowest latitude will have the strongest gravitational field strength. Charleston, WV will have largest gravitational field strength.

Hence, Charleston, WV which is at the lowest latitude will have the strongest gravitational field strength.

To learn more about Gravitational field strength, click:

https://brainly.com/question/29198014

#SPJ1

2 kg of steam at a pressure of 1 bar is contained in a rigid sealed tank whose volume is 3. 97 m3. The steam begins to cool off as heat is transferred to the atmosphere. When the internal pressure reaches 10 kPa, the tank walls will collapse.

a) What is the initial temperature of the steam in the tank (°C)?

b) What will the temperature be in the tank when the walls collapse (°C)?

c) At the instant of collapse, how many kg of water are in the liquid state?

d) What is the total change in internal energy (kJ) for the process? Does ????U increase or decrease?

Answers

According to the statement, about the internal pressure of the collapsing tank walls, we answer the following questions:

a) The initial temperature of the steam in the tank can be found using the ideal gas law:
PV = nRT
where P is the pressure, V is the volume, n is the number of moles of gas, R is the ideal gas constant, and T is the temperature. Rearranging the equation and solving for T gives:

T = PV/(nR)

Plugging in the given values:

T = (1 bar)(3.97 m3)/[(2 kg)/(0.018 kg/mol)(8.314 J/mol·K)]

T = 530.5 K

Converting to degrees Celsius:

T = 530.5 K - 273.15 K = 257.35°C

Therefore, the initial temperature of the steam in the tank is 257.35°C.

b) The temperature at the instant of collapse can be found using the same equation, but with the pressure at 10 kPa:

T = (10 kPa)(3.97 m3)/[(2 kg)/(0.018 kg/mol)(8.314 J/mol·K)]

T = 11.87 K

Converting to degrees Celsius:

T = 11.87 K - 273.15 K = -261.28°C

Therefore, the temperature in the tank when the walls collapse is -261.28°C.

c) At the instant of collapse, the amount of water in the liquid state can be found using the equation:

n = PV/RT

where n is the number of moles of water, P is the pressure, V is the volume, R is the ideal gas constant, and T is the temperature. Plugging in the values at the instant of collapse:

n = (10 kPa)(3.97 m3)/[(8.314 J/mol·K)(11.87 K)]

n = 4.02 mol

Converting to kilograms:

m = (4.02 mol)(0.018 kg/mol) = 0.07236 kg

Therefore, at the instant of collapse, there are 0.07236 kg of water in the liquid state.

d) The total change in internal energy can be found using the equation:

ΔU = nCvΔT

where ΔU is the change in internal energy, n is the number of moles of gas, Cv is the specific heat capacity at constant volume, and ΔT is the change in temperature. Plugging in the values:

ΔU = (4.02 mol)(20.8 J/mol·K)(-261.28 K - 257.35 K)

ΔU = -54,340 J = -54.34 kJ

Therefore, the total change in internal energy for the process is -54.34 kJ. Since the change in internal energy is negative, this means that the internal energy decreases during the process.

Learn more about internal pressure of the walls of a tank:

https://brainly.com/question/15967203

#SPJ11

Which one of the following properties most fundamentally distinguishes mechanical waves from electromagnetic waves? Mechanical waves have crests and troughs | Mechanical waves require a medium for propagation. | Mechanical waves have well-defined wavelengths. | Mechanical waves move at a finite speed.

Answers

The property that most fundamentally distinguishes mechanical waves from electromagnetic waves is that mechanical waves require a medium for propagation.

What are mechanical waves?

Mechanical waves are waves that require a medium in order to travel. Examples of mechanical waves are sound waves, seismic waves, and surface waves. These waves are created by a vibrating object, and the energy created is transferred through the medium, such as air or water.

The vibrations create compression and rarefaction regions, and these pressure changes travel away from the source. Mechanical waves are classified as either longitudinal or transverse. Longitudinal waves involve the particles of the medium vibrating in the same direction as the wave travels. Examples of this type of wave are sound waves. Transverse waves involve the particles of the medium vibrating at right angles to the direction in which the wave travels. Examples of this type of wave are ocean waves.

The property that most fundamentally distinguishes mechanical waves from electromagnetic waves is that mechanical waves require a medium for propagation.

Mechanical waves are waves that travel through a material medium, such as a solid, liquid, or gas, by causing particles in the medium to vibrate and transmit energy from one point to another.

On the other hand, electromagnetic waves do not require a medium and can travel through a vacuum, such as in space. Electromagnetic waves are waves of oscillating electric and magnetic fields, which can travel through space at the speed of light.

While mechanical waves do also typically have crests and troughs, well-defined wavelengths, and move at finite speeds, these properties are not unique to mechanical waves and can also apply to electromagnetic waves. For example, electromagnetic waves also have crests and troughs, well-defined wavelengths, and move at a finite speed.

To know more about Mechanical Waves, visit:

https://brainly.com/question/26116832

#SPJ4

is 0.5 a strong correlation?

Answers

In most situations, the strong correlation usually ranges between 0.7 to 0.9. So 0.5 is not a strong correlation.

Correlation is an important concept in statics. This helps to associate the relationship between two variables. This is of two types namely positive correlation and negative correlation.

In a positive correlation, the association of two variables occurs in the same way. That is they both decrease or increase. In a negative correlation, the association of one variable occurs oppositely to another variable. That is, when one variable decreases, another variable increases.

This correlation is represented by the symbol r. This r-value range from +1 to -1. So the perfect positive correlation is +1 and the perfect negative correlation is -1.

In, the positive correlation, the values from 0.1 to 0.3 is considered weak or low correlation. The values from 0.4 to 0.6 are considered a moderate correlation and the values from 0.7 to 0.9 are considered a strong correlation.

To know more about correlation:

https://brainly.com/question/22340487

#SPJ4

What is the time it takes to cause 40 watts of power with 7 J of work being done?
(Show work please)

Answers

The time taken to cause 40 watts of power with 7 J of work being done will be 0.175 seconds.

What is power?

Power is defined as the work done by the body per second. In other words, power is the rate of doing work. The amount of energy transferred or converted per unit of time is referred to as power.

The watt is the unit of power in the International System of Units, equal to one joule per second. Power is sometimes referred to as activity in older works. A scalar quantity is a power.

Given that the power is 40 watts and the work is 7 J. The time will be calculated as:-

Power = Work / Time

40 = 7 / Time

Time = 7 / 40

Time = 0.175 seconds

Therefore, the time will be 0.175 seconds.

To know more about power follow

https://brainly.com/question/25864308

#SPJ1

How waves are reflected from ionosphere?

Answers

Waves are reflected from the ionosphere due to the ionization of the atmosphere. The ionosphere is a layer of the Earth's atmosphere that is ionized by solar and cosmic radiation. This ionization creates a layer of free electrons that can reflect radio waves back to Earth.

The  ionization is the reason why radio waves can travel long distances, even around the curvature of the Earth.

The ionosphere is made up of several layers, each with different levels of ionization. The D layer is the lowest and is responsible for reflecting low frequency radio waves. The E layer is above the D layer and reflects medium frequency radio waves. The F layer is the highest and reflects high frequency radio waves.

The ionosphere of radio waves from the ionosphere is also affected by the angle of incidence of the wave. Waves that hit the ionosphere at a perpendicular angle are more likely to be reflected back to Earth, while waves that hit at a shallow angle are more likely to pass through the ionosphere and continue into space.

Waves are reflected from the ionosphere due to the ionization of the atmosphere and the angle of incidence of the wave. This reflection allows radio waves to travel long distances and is an important aspect of radio communication.

To know more about ionosphere here:

https://brainly.com/question/6575350#

#SPJ11

why a compartment that has the lowest water potential??

Answers

The compartment with the lowest water potential is typically the one with the highest solute concentration, which creates a strong osmotic pressure that draws water molecules from areas of higher water potential to areas of lower water potential.

This movement of water across cell membranes is essential for many biological processes, such as the uptake of water by plant roots and the regulation of blood volume in animals.

In plant cells, the compartment with the lowest water potential is often the cell's central vacuole, which contains a high concentration of solutes like sugars and ions. This creates a turgor pressure that helps maintain the cell's shape and rigidity. In animal cells, the compartment with the lowest water potential can vary depending on the specific cell type and its surrounding environment.

"

Correct question

Which compartment has the lowest water potential?

"

You can learn more about highest solute concentration at

https://brainly.com/question/30628239

#SPJ4

How much work is required to set up the four-charge configuration of the figure if q=3.12 pC, a = 46.5 cm, and the particles are initially infinitely far and at rest? Number units The number of significant digits is set to 3; the tolerance is +/-2%

Answers

The amount of work required to set up the four-charge configuration is 3.62 x 10⁻¹⁰ J.

How to calculate four-charge configuration?

To calculate the work required to set up the four-charge configuration, you need to calculate the potential energy of the system. The potential energy of a system of point charges is given by the formula:

U = k × ∑(qi × qj) / rij

Where k is Coulomb's constant (8.99 x 10⁹ N × m² / C²), qi and qj are the charges of the particles, and rij is the distance between them.

In this case, the four charges are located at the four corners of a square with side length a. The distance between each pair of charges is equal to the diagonal of the square, or √2 × a.

The total potential energy of the system can be calculated as:

U = k × (q² / (√2 × a)) + k × (q² / (√2 × a)) + k × (q² / (√2 × a)) + k × (q² / (√2 × a))

U = 4 × k × (q² / (√2 × a))

Substituting the given values:

U = 4 x 8.99 x 10⁹ N × m² / C² x (3.12 x 10⁻¹² C)² / (√2 x 46.5 cm)

U = 3.62 x 10⁻¹⁰ J

So, the work required to set up the four-charge configuration is 3.62 x 10⁻¹⁰ J.

Learn more on four-charge here: https://brainly.com/question/9101121

#SPJ1

A wire-wound resistor has a resistance of 200 ohms. What voltage applied between the terminals will produce a current of 0.08 amperes?

Answers

The voltage across the wire-wound resistor has a resistance of 200 ohms and the current across this circuit of 0.08 amperes will be 160 V.

What is Ohm's law?

Ohm's Law is a formula which is used to calculate the relationship between voltage or potential difference across the circuit, the electric current and resistance in an electrical circuit.

The expression for this law will be:

V = IR

where, V is the voltage,

I is the electric current,

R is the resistance across the circuit

V = IR

V = 200 × 0.8

V = 160 volts.

Learn more about Ohm's law here:

https://brainly.com/question/1247379

#SPJ1

during each heartbeat, about 80 g of blood is pumped into the aorta in approximately 0.20 s. during this time, the blood is accelerated from rest to about 1.0 cm/s. what is the average net force on the blood during this time?

Answers

The average net force on the blood during this time is 0.4 F

According to Newton's second law, we use formula

F=m.a

F=(m.v)/t

F= 80×1/0.20

F=0.4 F

Newton's II law

Newton's II law reads "An object with mass m experiences a resultant force of F will experience acceleration (a) whose direction is the same as the direction of the force and its magnitude is directly proportional to F and inversely proportional to mass (m)."

Every object tends to maintain its state as long as there is no resultant force acting on it. Newton's experimental results show that the force exerted on an object will cause the object to experience a change in velocity.

When the force is in the same direction as the object's motion, its speed increases and when the force is opposite to the object's motion, its speed decreases.

Formulas on Newton's Law II

F = m.a

F = the force acting on the object (N)

m = mass of object given force (kg)

a = acceleration of the object given the force (m/s2)

If the style works more than one is written:

∑F= ∑ m.a

Learn more about Newton's law at

https://brainly.com/question/15280051

#SPJ4

The specific heat at constant volume of a particular gas is 0.182 kcal/kg.K at room temperature, and its molecular mass is 34. What is the specific heat at constant pressure? What do you think is the molecular structure of this gas?

Answers

The specific heat at constant pressure (Cp) for the given gas is 1.049 kJ/kg.K. The molecular structure of the gas is likely to be monoatomic, with possible examples including helium, neon, and argon.

The specific heat at constant pressure (Cp) can be calculated from the specific heat at constant volume (Cv) using the relationship: Cp = Cv + R, where R is the gas constant for the particular gas. For air, R = 0.287 kJ/kg.K. Using the conversion factor 1 kcal = 4.186 kJ, we can convert the given value of Cv to the SI unit, and then calculate Cp:

Cv = 0.182 kcal/kg.K = 0.182 x 4.186 kJ/kg.K = 0.762 kJ/kg.K
Cp = Cv + R = 0.762 kJ/kg.K + 0.287 kJ/kg.K = 1.049 kJ/kg.K

The ratio of Cp to Cv for any gas is related to its molecular structure. For monoatomic gases, this ratio is equal to 5/3. For diatomic gases like nitrogen and oxygen, this ratio is equal to 7/5. For triatomic gases like carbon dioxide, this ratio is equal to 9/7. Since the calculated value of Cp/Cv for the given gas is 1.049/0.762 = 1.376, which is closer to 4/3, we can infer that the molecular structure of this gas is likely to be monoatomic. Possible examples of such gases include helium, neon, and argon.

Learn more about molecules here: brainly.com/question/19922822

#SPJ4

How do you find the squared period in physics?

Answers

To find the squared period of an object, you can use the following equation: T² = 4π²m/k
(Where T is the period, m is the mass of the object, and k is the spring constant or the force constant of the system.)



In physics, the squared period is a measure of the time it takes for an object to complete one full cycle or oscillation. It is often used to describe the behavior of oscillatory systems, such as pendulums or springs.

To find the squared period, you simply need to plug in the values for m and k and solve for T. Once you have found the period, you can square it to find the squared period.

For example, if you have a spring with a mass of 2 kg and a spring constant of 10 N/m, you would plug these values into the equation:

T² = 4π²(2 kg)/(10 N/m)

Solving for T gives you:

T = 2π√(2 kg/10 N/m)

T = 0.89 seconds

To find the squared period, you would simply square the period:

T² = (0.89 seconds)²

T² = 0.79 seconds²

So the squared period of this system is 0.79 seconds².

To know more about squared period here:

https://brainly.com/question/3435405#

#SPJ11

A goldfish is swimming at 2. 40 cm/s toward the front wall of a rectangular aquarium. What is the apparent speed (in cm/s) of the fish measured by an observer looking in from outside the front wall of the tank?.

Answers

The apparent speed of the fish measured by an observer looking in from outside the front wall of the tank is 1.50cm/s

For the plane surface (R=∞

n1​/p + n2/q = n2 −n1/R

​becomes q=−n2/n1 p

Thus the magnitudes of rate of change in the image and object positions are related by

dq/dt = n2/n1 dp/dt

if the fish swims towards the wall with a speed of 2 cm/s, the speed of the image is given by

v= dq/dt

= 1 (2)/ 1.3 =1.50cm/s

What is speed?

Distance divided by time is the dimension of speed. The metre per second (m/s) is the SI unit of speed, although the kilometre per hour (km/h) or, in the US and UK, miles per hour, is the most widely used measure in daily life (mph). The knot is a popular choice for air and sea travel.

To know more about speed, click the link given below:

https://brainly.com/question/28224010

#SPJ4

A toy car rolls along a flat, level floor for ten seconds traveling 25m. What is the average speed of the car? A toy car rolls along a flat, level floor for ten seconds traveling 25m. What is the average speed of the car?

Answers

The average speed of the car can be calculated by dividing the distance traveled by the time taken.

Average speed = distance/time

In this case, the distance traveled is 25m and the time taken is 10 seconds.

So,

Average speed = 25m/10s = 2.5 m/s

Therefore, the average speed of the car is 2.5 m/s.

How do you find the atomic radius on the periodic table?

Answers

The atomic radius on the periodic table generally increases from top to bottom within a group and decreases from left to right across a period.

The atomic radius refers to the distance between the nucleus of an atom and its valence electrons. It is measured in picometers (pm) or angstroms (Å). On the periodic table, elements are arranged in periods (horizontal rows) and groups (vertical columns).

Within a group, the atomic radius generally increases as you move down because the number of electron shells increases, resulting in a larger atomic radius.

To know more about the periodic table, here

brainly.com/question/11155928

#SPJ4

True/False?each different signal in a 1h nmr spectrum represents a different of hydrogen atom. hydrogen atoms that are give the same signal.

Answers

The statement (each different signal in a 1H NMR spectrum represents a different hydrogen atom. hydrogen atoms that give the same signal) is false because each different signal in a 1H NMR spectrum represents a different set of hydrogen atoms, not necessarily a single hydrogen atom.

Hydrogen atoms that are chemically equivalent, such as those in the same functional group or environment, give the same signal.

In addition to its use in identification, nuclear magnetic resonance (NMR) spectroscopy can provide in-depth knowledge about the structure, dynamics, reaction state, and chemical environment of molecules. Proton and carbon-13 NMR spectroscopy are the most popular forms of nuclear magnetic resonance (NMR), however, this technique can be applied to any kind of sample that has nuclei that have spin.

Want to know more about the NMR spectrum visit the link which is given below;

https://brainly.com/question/29775399

#SPJ4

What is the ICD-10 code for lung mass?

Answers

Answer:

Explanation:

The ICD-10 code for a lung mass can vary depending on the specific diagnosis, but some common codes include:

J98.11: Obstructive chronic bronchitis with (acute) exacerbation

J98.2: Other specified respiratory disorders

J98.8: Other specified respiratory disorders

J98.9: Unspecified respiratory disorder, not elsewhere classified

It is important to note that these codes are just a general guide and a definitive diagnosis should be made by a healthcare professional based on a patient's individual medical history and symptoms. The code assigned for a lung mass will depend on the underlying cause and the specific diagnosis determined by the clinician.

A fully charged capacitor initially has an air gap and is disconnected from the battery. A dielectric material is inserted between the plates What happen to the free charge at surface of the capacitor plates and the total charge free and bound at the surface of the capacitor plates?

Answers

When a dielectric material is inserted between the plates of a capacitor, the free charge on the surface of the capacitor plates will be reduced. This is because some of the free charge is transferred to the dielectric material.

What is the charge ?

The charge is the amount of money that someone is required to pay for a product or service. It is the cost that someone agrees to pay in exchange for goods or services. This charge can be either a fixed amount or a percentage of the total purchase amount. Charges can also include fees such as taxes, late fees, processing fees, and handling fees. Charges can be paid in cash, by credit card, or by check.

To learn more about charge

https://brainly.com/question/25922783

#SPJ4

the energy being used to do work is called energy and is the energy of motion.

Answers

The energy being used to do work is called kinetic energy, which is the energy of motion. Kinetic energy is a measure of the amount of energy an object possesses due to its motion.

What is kinetic energy?

The energy being used to do work is called kinetic energy, which is the energy of motion. Kinetic energy is a measure of the amount of energy an object possesses due to its motion.

Kinetic energy is a type of energy that an object possesses as a result of its motion. It is the energy associated with an object's movement or the energy that is being used to do work. Kinetic energy is proportional to the mass of an object and to the square of its velocity.

The formula for calculating the kinetic energy of an object is:

[tex]\mathrm{ KE = 0.5 \times m \times v^2 }[/tex]

where:

KE is the kinetic energy,

m is the mass of the object, and

v is its velocity.

In physics, kinetic energy is an important concept in the study of motion, energy, and work. It plays a crucial role in many areas of physics, including mechanics, thermodynamics, and quantum mechanics, among others.

To know more about kinetic energy, visit:

brainly.com/question/8101588

#SPJ4

What is one defining feature that separates comets from asteroids and meteoroids?
b
d
Comets are larger than moons, asteroids and meteoroids are smaller than moons.
Comets have an orbit, asteroids and meteoroids do not.
Comets are found on planet Earth, asteroids and meteoroids are only found in space.
Comets are covered in ice, asteroids and meteoroids are not.

Answers

Answer: d is correct

Explanation:

i did the quiz

the solar panels absorb sunlight that is later used to heat the house directly. the tree provides shade preventing heating of the house in the summer. how does the tree help in passive heating of the house in winter?

Answers

You can let sunlight into your home and help it get warmer by growing deciduous trees all around it.

How can you conserve energy by growing trees around your house?

Your heating and cooling expenses can be decreased by trees. In the summer, trees reduce energy use by cooling the air, while in the winter, they act as a wind break. As a result, less fossil fuels are burned to provide power for heating and cooling.

Planting deciduous trees around the house to shade your windows, doors, and external heat pump is one of the best passive heating/cooling techniques. Wintertime leaf loss on deciduous trees makes it possible for the sun's warm rays to enter the house and aid in keeping it warm. During the winter, most trees do 'slow down,' including deciduous trees that lose their leaves completely stop photosynthesis.

To learn more about photosynthesis use link below:
https://brainly.com/question/13027734

#SPJ4

How to use physics right hand rules?

Answers

Physics right hand rules can be used to determine the direction of a magnetic field, the direction of magnetic force, and the direction of current flow in a wire.

For example, to use the right hand rule for magnetic fields, you point your thumb in the direction of the current flow and curl your fingers in the direction of the magnetic field. This will give you the direction of the field lines. Similarly, the right hand rule for magnetic force involves pointing your index finger in the direction of the magnetic field, your middle finger in the direction of the current flow, and your thumb will point in the direction of the magnetic force acting on the wire.

To know more about the right hand rule, here

brainly.com/question/3930132

#SPJ4

As a wave moved from one medium to another there was a change in the wave’s speed. If the frequency of the wave does not change, what property of the wave must change, causing the change in speed?

Answers

Answer:

V = f λ        expresses wave speed where f is frequency and λ wavelength

If the frequency is unchanged across the boundary then the wavelength must change to account for the change in speed.

What is the minimum coefficient of friction needed between your back and the barrel wall ride (room spins, floor drops away) if the diameter of the circle is 2.8 m and it makes 1 revolution every 1.9 seconds?

Answers

The minimum friction coefficient needed can be calculated by dividing the calculated centripetal force by your weight.

What is friction coefficient?

To determine the minimum coefficient of friction needed between your back and the barrel wall for the ride, we need to calculate the centripetal force required to keep you in place and make sure that the friction force is greater than or equal to this force.

The centripetal force can be calculated using the formula:

F = m * v^2 / r

where:

m is your mass,

v is your speed (calculated as the circumference of the circle divided by the time for one revolution), and

r is the radius of the circle (which is half of the diameter, or 1.4 meters).

Using this formula, we can calculate the centripetal force required as follows:

v = (2 * pi * r) / t = (2 * pi * 1.4) / 1.9 = 4.27 m/s

F = m * v^2 / r = m * 4.27^2 / 1.4

Note: "pi" is a mathematical constant approximately equal to 3.14.

Now that we have the centripetal force, we can calculate the minimum friction force needed to keep you in place by using the formula:

F_friction = friction_coefficient * N

where:

friction_coefficient is the minimum coefficient of friction needed,

N is the normal force, which is equal to your weight in this case.

To find the minimum friction coefficient, we can set the centripetal force equal to the friction force:

F = friction_coefficient * N

friction_coefficient = F / N

So the minimum friction coefficient needed can be calculated by dividing the calculated centripetal force by your weight.

This is a rough estimate, as it assumes that you are stationary at the start of the ride, and it does not take into account any other forces that may affect your motion, such as air resistance or changes in the angle of the floor. In practice, a higher coefficient of friction may be necessary to ensure a safe and comfortable experience for the rider.

To know more about coefficient of friction , visit:

https://brainly.com/question/14121363

#SPJ4

The minimum friction coefficient needed can be calculated by dividing the calculated centripetal force by your weight.

What is friction coefficient?

To determine the minimum coefficient of friction needed between your back and the barrel wall for the ride, we need to calculate the centripetal force required to keep you in place and make sure that the friction force is greater than or equal to this force.

The centripetal force can be calculated using the formula:

[tex]F = m * v^2 / r[/tex]

where:

m is your mass,

v is your speed (calculated as the circumference of the circle divided by the time for one revolution), and

r is the radius of the circle (which is half of the diameter, or 1.4 meters).

Using this formula, we can calculate the centripetal force required as follows:

[tex]v = (2 * pi * r) / t = (2 * pi * 1.4) / 1.9 = 4.27 m/s[/tex]

[tex]F = m * v^2 / r = m * 4.27^2 / 1.4[/tex]

Note: "pi" is a mathematical constant approximately equal to 3.14.

Now that we have the centripetal force, we can calculate the minimum friction force needed to keep you in place by using the formula:

[tex]F_friction = friction_coefficient * N[/tex]

where:

friction_coefficient is the minimum coefficient of friction needed,

N is the normal force, which is equal to your weight in this case.To find the minimum friction coefficient, we can set the centripetal force equal to the friction force:

[tex]F = friction_coefficient * N[/tex]

[tex]friction_coefficient = F / N[/tex]

So the minimum friction coefficient needed can be calculated by dividing the calculated centripetal force by your weight.

This is a rough estimate, as it assumes that you are stationary at the start of the ride, and it does not take into account any other forces that may affect your motion, such as air resistance or changes in the angle of the floor. In practice, a higher coefficient of friction may be necessary to ensure a safe and comfortable experience for the rider.

To know more about coefficient of friction , visit:

brainly.com/question/14121363

#SPJ4

Indicate what happens when light strikes each type of matter listed below:

T = transmits straight through
B = refracts (bends)
R = reflects
A = absorbs

1) empty space (vacuum)
2) water in an aquarium
3) soil on a hillside
4) a glass window in a car
5) a brick wall
6) a lens in a camera
7) a mirror on a wall
8) water in a swimming pool
9) a roof covered with snow
10) a black shirt

Answers

The behavior of light, when it travels through the listed matters, can be found below.

The behavior of light upon striking surfacesEmpty space (vacuum): Light travels straight through it (T).Water in an aquarium: Light enters and refracts (bends) due to the change in density between air and water (B).Soil on a hillside: Light may reflect off the surface or be absorbed into the soil (R or A).A glass window in a car: Some light is transmitted through the window, some are reflected off the surface, and some are refracted as it passes through the glass (T, R, and B).A brick wall: Light may reflect off the surface or be absorbed into the wall (R or A).A lens in a camera: Light passes through and is refracted by the lens to form an image (B).A mirror on a wall: Light reflects off the mirror's surface (R).Water in a swimming pool: Light enters and refracts due to the change in density between air and water (B).A roof covered with snow: Light may reflect off the surface or be absorbed into the snow (R or A).A black shirt: Light is absorbed by the shirt's pigments, which do not reflect any color (A).

More on light can be found here: https://brainly.com/question/15200315

#SPJ1

Two blocks connected by a cord passing over a small, frictionless pulley rest on frictionless planes. (a) Which way will the system move when the blocks are released from rest? (b) What is the acceleration of the blocks? (c) What is the tension in the cord?

Answers

(a) System will move downward. (b) Acceleration is 1.96 m/s^2. (c) Tension in cord is 66.8 N.

(a) The block with the larger mass will move downward, and the block with the smaller mass will move upward. So the net force on the system is downward.

(b) The acceleration of the blocks is,

[tex]a = \dfrac{(m_2 - m_1)g}{(m1 + m2)}[/tex]

where m₁ and m₂ are the masses of the blocks and g is the acceleration due to gravity.

m₁ = 4 kg and m₂ = 6 kg

The acceleration is,

[tex]a = \dfrac{(6 - 4)(9.8)}{(4 + 6)}\\ = 1.96 m/s^2.[/tex]

(c) The tension in the cord,

[tex]T = m_2a + m_2g,[/tex]

where m2 is the mass of the block that is moving downward, a is the acceleration of the blocks, and g is the acceleration due to gravity.

[tex]T = (6)(1.96) + (6)(9.8)\\ = 66.8 N.[/tex]

Therefore, the tension in the cord is 66.8 N.

To know more about the tension, here

brainly.com/question/29124835

#SPJ4

Which of the following statements about speed and velocity is correct?Velocity only describes an object’s rate of motion.Speed describes how an object is changing its velocity.Speed and velocity both describe how an object is speeding up.Only velocity includes the direction an object is traveling.

Answers

Answer:

Velocity includes direction.

Explanation:

Velocity is a vector, so it has direction and magnitude.

At absolute zero temperature, how is the pressure that the fluid exerts on its system container?

Answers

At absolute zero temperature, the pressure that a fluid exerts on its container is determined by its quantum mechanical nature, rather than by thermal motion.

What happens at absolute zero temperature?

At absolute zero, the fluid would have no thermal motion, and all the particles would be in their lowest energy state. This means that the fluid would still exert pressure on its container, but it would be a residual pressure, determined by the quantum mechanical properties of the fluid.

In some cases, the residual pressure at absolute zero can be significant and can be calculated using the ideal gas law and quantum statistical mechanics. In general, residual pressure is a fundamental property of a fluid, and is related to its intermolecular forces and density.

However, it is important to note that it is not possible to reach absolute zero temperature in practice, due to the laws of thermodynamics and the limitations of current technology. Nevertheless, the residual pressure at absolute zero can still be studied theoretically and provides important insights into the behavior of fluids at very low temperatures.

To know more about absolute zero temperature, Check out:

https://brainly.com/question/3795971

#SPJ4

.

Calculate the Kinetic energy of a truck that has a mass of 2900 kg and is moving at 55 m/s.

Answers

The kinetic energy of the truck is 44,287,500 J as per the given data.

What is kinetic energy?

The energy an object has as a result of motion is known as kinetic energy. A force must be applied to an object in order to accelerate it.

The kinetic energy (K) of an object can be calculated using the formula:

[tex]K = 0.5 Xm X v^2[/tex]

Where,

m = mass of the object

v = velocity

Plugging in the values given in the question, we have:

[tex]K = 0.5 X 2900 X (55 m/s)^2[/tex]

[tex]K = 0.5 X 2900 X 3025 m^2/s^2[/tex]

K = 44,287,500 J (joules)

So, the kinetic energy of the truck is 44,287,500 J.

For more details regarding kinetic energy, visit:

https://brainly.com/question/26472013

#SPJ9

What is the Value of Mu Naught?

Answers

Mu naught, also known as vacuum permeability, is a physical constant that represents free space permeability. Its precise value is 4 x [tex]10^{-7}[/tex] henries per meter (H/m).

This constant appears in several electromagnetic equations, including Ampere's law and the Biot-Savart law. It is essential for calculating magnetic fields around electric currents and comprehending electromagnetic waves.

The value of mu nothing is regarded as a basic constant of nature, which means that it is thought to be the same everywhere in the cosmos and is not anticipated to vary throughout time. Its exact value has been found after multiple studies and measurements and is regarded as one.

Learn more about Naughts at

https://brainly.com/question/30404139

#SPJ4

Final answer:

Mu Naught is a physical constant in Physics, specifically the vacuum permeability or the magnetic constant, with a value of approximately 4π x 10^-7 T·m/A.

Explanation:

In Physics, Mu Naught is a physical constant, specifically, the vacuum permeability or the magnetic constant. It is used in various equations and calculations involving magnetically related phenomena. The value of Mu Naught is approximately 4π x 10^-7 Tesla meter per ampere (T·m/A).

For example, it is used in the formula of Biot–Savart law and Ampere’s law, which are essential in calculating the magnetic field generated by electric currents.

Learn more about Mu Naught here:

https://brainly.com/question/34609224

Other Questions
Describe the efforts that Toussaint went to in order to ease the burdens placed on the newly freed nation. What does this state about the man himself? To revitalize a local economy torn by conflict, Toussaint had to leverage his considerable political skills to reconcile the conflicting interests of Saint-Domingues racial, class, religious, and cultural orders. Judging the resources of the merchant and planter classes as integral to rebuilding Saint-Domingue, Toussaint extended generous restitution policies in the name of the republican fraternity, going so far as to punish any acts of retribution against former slaveholders. This ensured him a loyal base of allies who did his bidding at regional and international levels. Under his stewardship, Saint-Domingue initiated a robust civic overhaul and public works projects that created roads, widened canals, and improved public sanitation. Which characteristic is shared by both cnidarians and flatworms?A) dorsoventrally flattened bodiesB) flame cellsC) radial symmetryD) a digestive system with a single openingE) both A and D Please help.I need to explain the electromagnetic spectrum to fifth graders. What are the global issues in Exit West? what is the meaning of capitalism and freedom? Whoever answers first gets brainlist What is an example of rationalization defense mechanism? What are signs of ineffective tissue perfusion? Whati is the meaning of fassy 2. Evaluate justice and power in the USSR and Germany. Suppose that a single gene in a population has three alleles, or variants, A1, A2, and A3. In a mating pair of birds, the male has alleles A and A2, and the female has alleles A and A3. AA2 . What is the probability that A3 will be passed to any offspring? how many protein coding genes are in the human genome If you need a memo typed in a hurry take it to Vera she is the fastest typist of anyone in the office.If you need a memo typed in a hurry, take it to Vera; she is the fastest typist in the office. The lower Indus River (the part nearer the sea) flows through what is now the country of America TransformedAt the end of the 19th century, America struggled with a paradox: It was a nationof almost unlimited possibilities and wealth, but it was marked by great poverty andpain for many of its citizens. Reflecting this tension, a new literary movement known asrealism emerged, which expressed a view of life that was unsentimental, bitterly ironic,and often harsh or ugly. i gore bitEngines of Social Changeblooo how volal simeof turIn the two decades after the completion of the transcontinental railroad, the railsystem brought thousands of settlers to the West. The railroad industry also became anengine for industrial growth as new manufacturing centers grew up around railroadhubs in Pittsburgh, Cleveland, Detroit, and Chicago. New technologies and industrialmodernization brought prosperity to large parts of the nation.onog zidWrite a 2-3 sentence summary of the text:imov todais Nicole has two bags of coins. The first bag contains 5 silver dollars, 4 quarters, and 6 dimes. The second bag contains 2 silver dollars, 3 quarters, and 2 dimes. Nicole is going to let her little brother, Jacob, randomly select and keep 1 coin from each bag. What is the probability that Jacob will choose a silver dollar from each bag? What is close ended questions examples ? Suppose Joan has a fair four-sided die with sides that are numbered 1, 2, 3, and 4.After she rolls it 2,000 times, she finds that she rolled the number 2 a total of 187 times. Which of the following is true?A. Joan has provided evidence that calls into question whether or not this is a fair die because the relative frequency of rolling a 2 is quite different than the theoretical probability even after repeating the experiment many times.B. Joan has demonstrated that this is a fair die, since the relative frequency of rolling a 2 is nearly equal to the theoretical probability.C. We cannot draw any conclusions from Joan's experience with this die because there is only a very weak link between the relative frequency of an event and the theoretical probability.D. We cannot draw any conclusions from Joan's experience with this die without also knowing how many times the other numbers appeared. what is the name of a drug that inhibits the metabolism of acetaldehyde, so alcohol consumption causes headaches and other unpleasant symptoms of acetaldehyde toxicity? Why are economies most efficient when they have full employment?A. No productive resources are left unusedB. No one person has to work too hard. C. Wages are spent for consumer goodsD. Unemployment offices can be closed.