Two resistors have resistances R1 and R2. When the resistors are connected in series to a 12.6-V battery, the current from the battery is 2.07 A. When the resistors are connected in parallel to the battery, the total current from the battery is 8.98 A. Determine R1 and R2. (Enter your answers from smallest to largest.)
Answer:
When R1 = 2.193, R2 = 3.894
When R1 = 3.894, R2 = 2.193
Explanation:
We are told that when R1 and R2 are connected in series, the voltage is 12.6 V and the current is 2.07 A.
Formula for resistance is;
R = V/I
R = 12.6/2.07
R = 6.087 ohms
Since R1 and R2 are connected in series.
Thus; R1 + R2 = 6.087 ohms
R1 = 6.087 - R2
We are also told that when they are connected in parallel, the current is 8.98 A.
Thus, R = 12/8.98
R = 1.403 ohms
Thus;
(1/R1) + (1/R2) = 1/1.403
Let's put 6.087 - R2 for R1;
(1/(6.087 - R2)) + (1/R2) = 1/1.403
Multiply through by 1.403R2(6.087 - R2) to get;
1.403R2 + 1.403(6.087 - R2) = R2(6.087 - R2)
Expanding gives;
1.403R2 + 8.54 - 1.403R2 = 6.087R2 - (R2)²
(R2)² - 6.087R2 + 8.54 = 0
Using quadratic formula, we have;
R2 = 2.193 ohms or 3.894 ohms
Thus,
R1 = 6.087 - 2.193 or R1 = 6.087 - 3.894
R1 = 3.894 or 2.193
When R1 = 2.193, R2 = 3.894
When R1 = 3.894, R2 = 2.193
A ball rolls along the floor with a constant velocity of 12 m/s. How far will it have
gone after 6 seconds?
Answer:
72m
12m x 6s=72m
there ya go
Solve the below problems being sure to provide the correct significant figures.
1) 1000 ÷ 4.886 = __________
2) 240 ÷ 12.3 = __________
3) 80 x 4.6 = __________
4) 4.527 x 30 = __________
5) 86 x 63.855 x 8000 = __________
6) 700 x 91.186 = __________
7) 7.1 x 348 = __________
8) 50 ÷ 29.1 = __________
9) 98.773 x 24.891 x 409 = __________
10) 0.065 x 3 x 3007 = __________
Answer:
1) 204.6663938
2) 19.51219512
3) 368
4) 135.81
5) 43932240
6) 63830.2
7) 2470.8
8) 1.718213058
9) 1005550.526
10) 586.365
Most of the questions you asked were in repeating decimal form.
Explanation:
Two 10-cm-diameter charged rings face each other, 21.0 cm apart. Both rings are charged to +40.0 nC. What is the electric field strength ?
Complete question:
Two 10-cm-diameter charged rings face each other, 21.0 cm apart. Both rings are charged to +40.0 nC. What is the electric field strength at the midpoint between the two rings ?
Answer:
The electric field strength at the mid-point between the two rings is zero.
Explanation:
Given;
diameter of each ring, d = 10 cm = 0.1 m
distance between the rings, r = 21.0 cm = 0.21 m
charge of each ring, q = 40 nC = 40 x 10⁻⁹ C
let the midpoint between the two rings = x
The electric field strength at the midpoint between the two rings is given as;
[tex]E_{mid} = E_{right} +E_{left}\\\\E_{right} = \frac{KQ}{(x^2 + r^2)^\frac{2}{3} } \\\\E_{leftt} = -\ \frac{KQ}{(x^2 + r^2)^\frac{2}{3} }\\\\E_{mid} = \frac{KQ}{(x^2 + r^2)^\frac{2}{3} } - \frac{KQ}{(x^2 + r^2)^\frac{2}{3} } = 0[/tex]
Therefore, the electric field strength at the mid-point between the two rings is zero.
Calculate the first and second order angles for light of wavelength 400. nm and 700. nm of the grating contains 1.00 x 104 lines/cm.
Answer:
[tex]23.58^{\circ}[/tex] and [tex]53.13^{\circ}[/tex]
[tex]44.43^{\circ}[/tex], second order does not exist
Explanation:
n = Number of lines grating = [tex]1\times10^4\ \text{Lines/cm}[/tex]
[tex]\lambda[/tex] = Wavelength
m = Order
Distance between slits is given by
[tex]d=\dfrac{1}{n}\\\Rightarrow d=\dfrac{1}{1\times 10^4}\\\Rightarrow d=10^{-6}\ \text{m}[/tex]
[tex]\lambda=400\ \text{nm}[/tex]
m = 1
We have the relation
[tex]d\sin\theta=m\lambda\\\Rightarrow \theta=\sin^{-1}\dfrac{m\lambda}{d}\\\Rightarrow \theta=\sin^{-1}\dfrac{1\times 400\times 10^{-9}}{10^{-6}}\\\Rightarrow \theta=23.58^{\circ}[/tex]
m = 2
[tex]\theta=\sin^{-1}\dfrac{2\times 400\times 10^{-9}}{10^{-6}}\\\Rightarrow \theta=53.13^{\circ}[/tex]
The first and second order angles for light of wavelength 400 nm are [tex]23.58^{\circ}[/tex] and [tex]53.13^{\circ}[/tex].
[tex]\lambda=700\ \text{nm}[/tex]
m = 1
[tex]\theta=\sin^{-1}\dfrac{1\times 700\times 10^{-9}}{10^{-6}}\\\Rightarrow \theta=44.43^{\circ}[/tex]
m = 2
[tex]\theta=\sin^{-1}\dfrac{2\times 700\times 10^{-9}}{10^{-6}}[/tex]
Here [tex]\dfrac{2\times 700\times 10^{-9}}{10^{-6}}=1.4>1[/tex] so there is no second order angle for this case.
The first order angle for light of wavelength 700 nm are [tex]44.43^{\circ}[/tex].
Second order angle does not exist.
a cohesive force between the liquids molecules is responsible for the fluids is called
Answer:
static force
Explanation:
mark me brainliest
which energy conservation takes place when a toaster is switched on?
Answer:
A toaster usually takes in electrical energy.
Two types of energy are created.
In the first step, all of the input electrical energy is transformed into heat energy. That heat goes first into the coils or heating elements.
The heating elements get hot and glow.
The hot elements then transfer thermal energy (heat energy) into the air inside the toaster.
Explanation:
Answer: electrical energy
Explanation: An electric toaster takes in electrical energy from the power outlet and converts it into heat, very efficiently. If you want your toast to cook quickly, you need a toaster that radiates as much heat as possible each second onto your bread. hope this helps. Can u pls give me brainliest
What is the scientific study of how animals are classified?
Answer:
biology
Explanation:
Animals and plants
If soldiers march across the bridge with a cadence equal to the bridge’s natural frequency and impart 1x104 J of energy each second, how long does it take for the bridge’s oscillations to go from 0.1 m to 0.5 m amplitude?
Answer: Hello, Mark me as Brainliest! :)
If soldiers march across the bridge with a cadence equal to the bridge's natural frequency and impart $$1.00 × 10^4 J$$ of energy each second, how long does it take for the bridge's oscillations to go from 0.100 m to 0.500 m amplitude. $ 5 \times 10^7 \text{J} $ . \\ b) $ 12 \times 10^4 \text{s}$ .
Your Welcome!
Explanation:
please answer asap! will give brainliest if correct! ^^
A train of waves is moving at a speed of 30 m/s. The frequency of the waves is 10 Hz. What is the wavelength?
a. 300 m
b. 30 m
c. 3 m
d. 0.1 m
Answer:
the answer is c, 3m......
When a train is moving at the speed of 30 m/s. The wavelength of the wave is 3 m.
What is wavelength?Wavelength is the characteristic of the wave which represents the distance between the adjacent crest or trough of the wave.
Given is the speed of the train of waves 30 m/s and frequency of the wave is 10 Hz, then the wavelength is related to speed and wavelength as
v = fλ
30 = 10 × λ
λ = 3 m
Thus, the wavelength of the wave is 3 m.
Learn more about wavelength.
https://brainly.com/question/13533093
#SPJ2
Force exerted on a body changes it's
While a boulder is on top of a hill, it has kinetic energy.
True
False
A ball on a string in uniform circular motion has a velocity of 8 meters per second, a mass of 2 kilograms, and the radius of the circle is 0.5 meters. What is the centripetal force keeping the ball in the circle?
Answer:
256 N
Explanation:
formula of centripetal force = mv²/r
m= 2kg
v= 8m/s
r= 0.5m
mv²/r = 2×8²/0.5 = 256N
A planet with a mass one-half that of Earth has a radius that is 3 times that of Earth's radius. What is the gravitational field strength of the planet?
The gravitational acceleration of a planet is proportional to the planet's mass, and inversely proportional to square of the planet's radius.
So when you stand on the surface of this particular planet, you feel a force of gravity that is
(1/2) / (3²)
of the force that you feel on the surface of the Earth.
That's (1/18) as much as on Earth.
The acceleration of gravity there would be about 0.545 m/s².
This is about 12% less than the gravity on Pluto.
A bump should primarily be used in which situation?
A. when the ball is going out of bounds
B. when returning a serve
C. to start game play
A uniform-density 7 kg disk of radius 0.20 m is mounted on a nearly frictionless axle. Initially it is not spinning. A string is wrapped tightly around the disk, and you pull on the string with a constant force of 42 N through a distance of 0.9 m. Now what is the angular speed
Answer:
The angular speed is 23.24 rad/s.
Explanation:
Given;
mass of the disk, m = 7 kg
radius of the disk, r = 0.2 m
applied force, F = 42 N
distance moved by disk, d = 0.9 m
The torque experienced by the disk is calculated as follows;
τ = F x d = I x α
where;
I is the moment of inertia of the disk = ¹/₂mr²
α is the angular acceleration
F x r = ¹/₂mr² x α
The angular acceleration is calculated as;
[tex]\alpha = \frac{2Fr}{mr^2} \\\\\ \alpha = \frac{2F}{mr}\\\\\alpha = \frac{2 \times 42 }{7 \times 0.2} \\\\\alpha = 60 \ rad/s^2[/tex]
The angular speed is determined by applying the following kinematic equation;
[tex]\omega _f^2 = \omega_i ^2 + 2\alpha \theta[/tex]
initial angular speed, ωi = 0
angular distance, θ = d/r = 0.9/0.2 = 4.5 rad
[tex]\omega _f^2 = 2\alpha \theta\\\\\omega _f = \sqrt{2\alpha \theta} \\\\\omega _f = \sqrt{2 \times 60 \times 4.5} \\\\\omega _f = 23.24 \ rad/s[/tex]
Therefore, the angular speed is 23.24 rad/s.
As a delivery truck travels along a level stretch of road with constant speed, most of the power developed by the engine is used to compensate for the energy transformations due to friction forces exerted on the delivery truck by the air and the road. If the power developed by the engine is 4.12 hp, calculate the total friction force acting on the delivery truck (in N) when it is moving at a speed of 30 m/s. One horsepower equals 746 W.
Answer:
102.5N
Explanation:
Given that a delivery truck travels along a level stretch of road with constant speed, most of the power developed by the engine is used to compensate for the energy transformations due to friction forces exerted on the delivery truck by the air and the road. If the power developed by the engine is 4.12 hp, calculate the total friction force acting on the delivery truck (in N) when it is moving at a speed of 30 m/s. One horsepower equals 746 W
The power = 4.12 × 746 = 3073.52 W
Using the formula
Power = force × velocity
3073.52 = force × 30
Force = 3073.52 / 30
Force = 102.5 N
Since most of the power developed by the engine is used to compensate for the energy transformations due to friction forces exerted on the delivery truck by the air and the road, therefore,
the total friction force acting on the delivery truck (in N) when it is moving at a speed of 30 m/s is 102.5 N
If it takes 560 joules of work to move an object 10 meters what force was needed
Answer:
F = 56 N
Explanation:
Assuming that the applied force is parallel to the displacement, according to the definition of work, we can write the following expression for the force required:[tex]F = \frac{W}{\Delta x} =\frac{560J}{10m} = 56 N (1)[/tex]
A 50 N force causes a spring to compress 0.09 m. What is the spring constant? What is the potential energy of the spring?
Resolution
using hooke's relation
F = K . d
50N = k . 0.09m
k = 50N / 0.09m
k = 5555.56 N/m
Calculating the potential energy of the spring
Ep = 1/2 k . x²
Ep = 1/2 (5555.56 N/m) (0.09m)²
Ep = 22.5 Joules
Answer
the spring constant? =
k = 5555.56 N/m
potential energy of the spring?
Ep = 22.5 Joules
The Potential energy of the spring is 2.25 J
What is the Potential energy of spring?This is the energy stored in spring due to its elastic properties.
To calculate the potential energy of the spring, we use the formula below.
Formula:
E = Fe/2................ Equation 1Where:
E = Potential energy of the springF = Force applied to the springe = compression.From the question,
Given:
F = 50 Ne = 0.09 mSubstitute these values into equation 1
E = 50(0.09)/2E = 2.25 J.Hence, The Potential energy of the spring is 2.25 J
Learn more about the potential energy of spring: https://brainly.com/question/3510901
If we always drop the balls from 1-m
height in each trial, what type of variable
is this in this experiment?
Constant Variable
Dependent Variable
Independent Variable
Answer:
height
weight of ball
time of ball falling
(will give brainliest to whoever answers first and explains reasoning) A 10kg object is spun around in a circle with a centripetal acceleration of 3.5m/s^2. What is the centripetal force acting on the object?
Answer:
35 N
Explanation:
F = ma
centripetal force = 10(3.5) = 35 N
I don’t understand this
Answer:
true
Explanation:
force or powerbecause he pushes a disk
A small town has decided to forego the use of electrical power and send energy through town via mechanical waves on ropes. They use rope with a mass per length of 1.50 kg/m under 6000 N tension. If they are limited to a wave amplitude of 0.500 m, what must be the frequency of waves necessary to transmit power at the average rate of 2.00 kW
Answer:
the required frequency of waves is 2.066 Hz
Explanation:
Given the data in the question;
μ = 1.50 kg/m
T = 6000 N
Amplitude A = 0.500 m
P = 2.00 kW = 2000 W
we know that, the average power transmit through the rope can be expressed as;
p = [tex]\frac{1}{2}[/tex]vμω²A²
p = [tex]\frac{1}{2}[/tex]√(T/μ)μω²A²
so we solve for ω
ω² = 2P / √(T/μ)μA²
we substitute
ω² = 2(2000) / √(6000/1.5)(1.5)(0.500)²
ω² = 4000 / 23.71708
ω² = 168.65
(2πf)² = ω²
so
(2πf)² = 168.65
4π²f² = 168.65
f² = 168.65 / 4π²
f² = 4.27195
f = √4.27195
f = 2.066 Hz
Therefore, the required frequency of waves is 2.066 Hz
what colors of light are absorbed when white light falls on a green object?
1
Select the correct answer.
Which type of energy is thermal energy a form of?
A
chemical energy
B.
kinetic energy
C. magnetic energy
D. potential energy
Reset
Next
Answer:
B. kinetic energy
Explanation:
Thermal energy (It’s a low form of energy ) is a form of kinetic energy as it is produced as a result of motion of particles either if they vibrate at their position or they move along longer paths.
a boy throws a ball straight up into the air it reaches the highest point of its flight after 4 seconds how fast was the ball going when it left the boy's hand
Answer:
Gravity pulls down on the ball at g=-9.81 m/s^2. Up is positive, down is negative. The ball started at a certain initial velocity of Vi m/s. Time it took is t=4s. Final velocity is Vf=0 m/s, because at the highest point the ball stops moving.
prove that d1=R(d1-d2) in relative density
What is the weight of a 48kg rock?
Answer:
48kg
Explanation:
an iron Tyre of diameter 50cm at 288k is to be shrank on to a wheel of diameter 50.35cm.To what temperature must the tyre be heated so that it will slip over the wheel with a radial gap of 0.5mm.Linear expansivity of iron is 0.000012k-1
Answer:
The answer should be D
Explanation:
The amount of light that enters the pupil is controlled by the:
retina.
lens.
inis.
Answer: The amount of light that enters the pupil is controlled by the Iris
Explanation: