When using compass orientation, migrating animals make use of the sun, stars, and Earth's magnetic field to navigate. So, option d is correct option.
Compass orientation in migrating animals is the process of using the sun, stars, and Earth's magnetic field to navigate. Migrating animals use a variety of techniques to navigate, depending on their species and environment.
Some animals use the position of the sun, stars, and Earth's magnetic field as their primary means of orientation when migrating. This is known as compass orientation.
Compass orientation is a technique that relies on environmental cues, such as the position of the sun and stars, to determine direction. Some animals can use the Earth's magnetic field to navigate as well. This is known as magnetic orientation.
Magnetic orientation is used by some species of birds and fish, as well as certain insects and reptiles. Other animals use landmarks and olfactory cues to navigate.
These animals rely on visual or chemical markers in the environment to orient themselves. This technique is known as piloting. Piloting is used by animals such as rodents, bats, and some species of birds. Animals that use piloting must be able to remember and recognize the landmarks they use as cues to navigate.
Finally, some animals use memories from previous trips with parents to navigate. This technique is known as true navigation. True navigation requires animals to have a highly developed sense of spatial awareness and memory. True navigation is used by animals such as sea turtles and some species of birds.
All of these techniques require different cognitive abilities and sensory mechanisms, but they allow animals to navigate over long distances to reach their desired destinations.
for similar question on magnetic field to navigate.
https://brainly.com/question/22986969
#SPJ11
Calculate the net force in each scenario below:
1.
2.
3.
4.
5.
20 N
40 N
20 N
8N
10 N
3N
7N
40 N
10 N
10 N
10 N
Net Foros:
Net Force:
Net Force:
Net Force:
Net Force:
Direction of motion:
Place a star inside the boxes that are UNBALANCED
Answer:
1. Net force: 60N (⭐️)
Direction: West
2. Net force: 60N
Direction: East
3. Net force: 18N (⭐️)
Direction: East
4. Net force: 20N
Direction: No movement
5. Net force: 20N
Direction: No movement
Explanation:
Hope you understand :)
a 38000 kg railroad freight car collides with a stationary caboose car. they couple together and 18 percent of the initial kinetic energy is dissipated as heat, sound, vibrations, and so on. what is the mass of the caboose
The mass of the caboose is 38,000 kg since the caboose car is equal to the mass of the first car, which is 38,000 kg.
Before the collision, only the first car has kinetic energy, which is given by (1/2)mv², where m is the mass of the first car and v is its velocity. After the collision, both the cars have the same velocity. Thus, the total kinetic energy is (1/2)Mv², where M is the total mass of the two cars.After the collision, a part of the kinetic energy of the first car is dissipated as heat, sound, and other forms of energy.
Let's assume that the remaining kinetic energy is K. Thus, we can write K = (1 - 18/100) (1/2)mv² = 0.82 (1/2)mv². The total kinetic energy of the two cars is K = (1/2)Mv². On equating the two equations of K, we get(1/2)mv² = (1/2)Mv². Solving for M, we get M = m. The mass of the second car, i.e., the caboose car is equal to the mass of the first car, which is 38,000 kg. Hence, the answer is 38,000 kg.
More on mass: https://brainly.com/question/2153129
#SPJ11
what device is used to shunt transient current to ground in the event of an indirect lightning strike?
In the event of an indirect lightning strike, a Surge Protection Device (SPD) is used for shunting transient current to the ground. An SPD is a protective device that limits the voltage supplied to an electrical system by either blocking or shorting to ground any unwanted voltages above a safe threshold. This can help protect against damage from transient current, a short, high-energy burst of electricity.
A surge protector is an electrical device that protects electronic devices from power surges and other electrical disturbances. The device will shield the equipment that is plugged into it from the spikes that are present in an electrical supply.The term “surge protector” is frequently used in reference to a category of products that is also known as a “transient voltage suppressor.” This name provides insight into how these devices work. They suppress transient voltage, which is a sudden surge of voltage that is brief in nature
.How do surge protectors work?
Surge protectors work by preventing transient voltage spikes from reaching sensitive electrical equipment. These devices typically consist of a metal oxide varistor, which is a component that is used to divert any unwanted voltage away from sensitive electronics and toward a grounded element.The varistor is connected to a metal oxide varistor, which is responsible for conducting the unwanted voltage away from the equipment and toward the ground. Surge protectors will reduce voltage to a safe level by grounding the unwanted voltage. Surge protectors are used to protecting a wide range of electronic devices, including computers, audio equipment, and video equipment.
For more details go through the link: https://brainly.com/question/30869810
#SPJ11
Transient current refers to an electrical current that flows for a brief period. Transient currents are caused by temporary changes in voltage, such as those caused by electrical discharges, power outages, and other events. Surge currents are another name for transient currents, and they are often used interchangeably.
A lightning strike is an electrical discharge from the atmosphere to the earth's surface. Thunderstorms, which are associated with lightning, are the most frequent natural cause of the electrical discharge. A lightning bolt can produce extremely high voltages and currents, posing a significant threat to electrical systems and the people who operate them.
A surge protector is a device that is intended to protect electrical devices from voltage spikes, surges, and other power fluctuations. Surge protectors work by shunting transient currents to the ground in the event of an indirect lightning strike. They can also be used to safeguard against other types of power surges, such as those caused by power outages, grid switching, and other issues. Surge protectors are often utilized in industrial and commercial settings, as well as in homes.
For more information regarding this topic, you can click the below link
https://brainly.com/question/1100341
#SPJ11
A bitmap image is provided in two different resolutions. Image 1 has a resolution of 1500 x 1225. Image 2 has a resolution of 500 x 350. Which of the following statements is true when the sizes of both the files are increased by 25 percent?
Image 1 is sharper than image 2 and has a larger file size than image 2.
The true statement is "Image 1st is sharper than Image 2nd and has a larger file size than Image 2nd"
What is a bitmap image?A bitmap image is a type of digital image that is made up of pixels, which are small squares of color that form an image.
Bitmap image also known as raster images.
Explain image resolution?Image resolution refers to the number of pixels contained in a digital image, typically measured as the number of pixels per inch (PPI) or dots per inch (DPI). The resolution of an image determines the level of detail and clarity that can be seen in the image.
To know more about bitmap image, visit:
https://brainly.com/question/26230407
#SPJ1
As a wave moves through a medium, the individual particles of the medium move from source of the wave to another location some distance away.
True or False
Answer:
False: Generally, the particles move in a vertical direction, vibrating perpendicular to the propagation of the wave.
write the equations for the balance of the forces in the horizontal and vertical directions for block a and for block b (four equations). start with the force exerted on block a in the horizontal direction.
The equations for the balance of forces in the horizontal and vertical directions for Block A and Block B are: Horizontal direction of Block A: T = 12.5 N,Vertical direction of Block A: W = 24.5 N,Horizontal direction of Block B: T = 22.5 N and Vertical direction of Block B: W = 44.1 N.
The forces acting on Block A are: Force of tension (T) and Force of gravity (W).The forces acting on Block B are: Force of tension (T) and Force of gravity (W).For Block A in the horizontal direction, the force exerted will be the force of tension (T).
Therefore: Horizontal direction of Block A: T = mA a ………………….. (1) For Block A in the vertical direction, the force exerted will be the force of gravity (W).
Therefore: Vertical direction of Block A: W = mA g ………………….. (2) For Block B in the horizontal direction, the force exerted will also be the force of tension (T).
Therefore: Horizontal direction of Block B: T = mB b ………………….. (3) For Block B in the vertical direction, the force exerted will be the force of gravity (W).
Therefore: Vertical direction of Block B: W = mB g ………………….. (4)
The equations can be solved by substituting the values of the masses and the acceleration due to gravity. Therefore, equations (1) to (4) will become:
Horizontal direction of Block A: T = 2.5 (5) = 12.5 N Vertical direction of Block A: W = 2.5 (9.8) = 24.5 N Horizontal direction of Block B: T = 4.5 (5) = 22.5 N Vertical direction of Block B: W = 4.5 (9.8) = 44.1 N
Therefore, the equations for the balance of forces in the horizontal and vertical directions for Block A and Block B are:
Horizontal direction of Block A: T = 12.5 N Vertical direction of Block A: W = 24.5 N Horizontal direction of Block B: T = 22.5 N Vertical direction of Block B: W = 44.1 N
More on forces: https://brainly.com/question/14932990
#SPJ11
What waves are transverse body waves with a shearing motion?
S-waves are transverse body waves that cause damage during earthquakes by shearing the material they pass through. They move perpendicular to the direction of wave propagation, are secondary to P-waves, and cannot travel through fluids.
Seismographs can pick up transverse body waves known as S-waves as they go through the interior of the Earth. This causes the material's particles to vibrate perpendicular to the wave direction, which produces a shearing motion. These waves move perpendicular to the direction of wave propagation. Because S-waves move more slowly than primary waves, which are longitudinal waves that compress and expand the material they pass through, they are also known as secondary waves. Since shear stress cannot exist in fluids, P-waves cannot pass through fluids or solids. This restricts the S-wave detection to regions of the Earth's mantle. The shearing motion brought on by S-waves during an earthquake can significantly stress and strain a building's foundation. leading to collapse or other forms of structural damage.
learn more about S-waves here:
https://brainly.com/question/26489416
#SPJ4
a test tube standing verticslly in a test tube rack contains 2.5 cm of oil and 6.5 cm of water. what is the pressur eon the bottom of the tube
The pressure on the bottom of the test tube which contain both the oil and water molecules is about 641.65 Pa + 220.725 Pa = 862.375 Pa.
What is the pressure in test tube?The pressure at the bottom of the test tube is the result of two factors: the weight of the oil and the weight of the water molecules. The pressure is equal to the density of each liquid multiplied by the height of each liquid, multiplied by the gravitational acceleration (g).
The pressure at the bottom of the test tube is given by the density of the fluids and also the height of the column above the bottom region. The pressure at the bottom of the test tube is calculated by multiplying the density of the fluids by the height of the column above the bottom. Here's how to calculate the pressure:
P = pgh
where P = Pressure, p = Density of fluid, g = Acceleration due to gravity, and h = Height of the column.
The pressure at the bottom of the test tube is the pressure which is exerted by the water and oil above it. The water is more dense than that of the oil, therefore it exerts more pressure on the bottom of the test tube. The pressure at the bottom of the test tube is given by the formula
The density of water is 1000 kg/m³, and the density of oil is 900 kg/m³. The height of the column of water is 6.5 cm, and the height of the column of oil is 2.5 cm.
Using the above formula: P = pgh
P (Water) = 1000 × 9.81 × 0.065
P (Water) = 641.65 Pa
P (Oil) = 900 × 9.81 × 0.025
P (Oil) = 220.725 Pa
Therefore, the pressure on the bottom of the tube is 641.65 Pa + 220.725 Pa = 862.375 Pa.
Learn more about Pressure here:
https://brainly.com/question/29672166
#SPJ11
what would happen to the gravitational force between the sun and sirius, another main sequence star, if the mass of sirius were to triple?
Answer:
It would triple.
Explanation:
By Newtown's law of universal gravitation, the ration is 1:1
Choose the correct law that corresponds to the given statements: 1. In a mixture of gases, each gas will exert its own partial pressure, regardless of the partial pressures of other gases in the mixture.______
2. In a closed system, pressure and volume have an inverse relationship. ______
3. The amount of gas that will dissolve in a fluid is determined by the solubility of the gas in the given fluid. ______
The correct law that corresponds to the given statements is:
1. In a mixture of gases, each gas will exert its own partial pressure, regardless of the partial pressures of other gases in the mixture. Dalton's law of partial pressures
2. In a closed system, pressure and volume have an inverse relationship. Boyle's law
3. The amount of gas that will dissolve in a fluid is determined by the solubility of the gas in the given fluid. Henry's law
1. In a mixture of gases, each gas will exert its own partial pressure, regardless of the partial pressures of other gases in the mixture: Dalton's law of partial pressures states that the total pressure of a mixture of gases is equal to the sum of the partial pressures of the individual gases in the mixture.
2. In a closed system, pressure and volume have an inverse relationship: Boyle's law states that the volume of a gas at constant temperature is inversely proportional to the pressure exerted by the gas.
3. The amount of gas that will dissolve in a fluid is determined by the solubility of the gas in the given fluid: Henry's law states that the amount of a gas that will dissolve in a liquid is directly proportional to the partial pressure of the gas above the liquid and the solubility of the gas in the liquid.
Learn more about partial pressures here:
https://brainly.com/question/16118479
#SPJ11
A lightbulb is in series with a 2.0 ohm resistor The lightbulb dissipates 10 W when this series circuit is connected to a battery. What is the current through the lightbulb? There are two possible answers; give both of them. Enter your answers in ascending order separated by commas. I = 1.78,2.96 A
The current through the lightbulb when a lightbulb is in series with a 2.0 ohm resistor is I = 1.78 A, 2.96 A.
The current through the lightbulb when a lightbulb is in series with a 2.0 ohm resistor is given by the Ohm's Law. Ohm's law states that current through a conductor between two points is directly proportional to the voltage across the two points. In other words, V = IR. Where V is the voltage, I is the current and R is the resistance. When the circuit is connected to a battery, the lightbulb dissipates 10W. Power can also be expressed as P = IV, where P is the power, I is the current and V is the voltage. We have V = IR and P = IV.
We can substitute V in terms of I from the first equation to the second equation.P = I²R=> I² = P/R=> I = √(P/R) = √(10W/2Ω) = 2.24 A. There are two possible answers. When we apply Ohm's Law to the circuit, I = V/R Where R = 2.0 Ω and V is the voltage across the resistor.I = V/2 = (10/2)^(1/2) A = 1.78 A.The other possible answer is the current through the light bulb.I = (10/2.0 + 2.0) A = 2.96 A. Therefore, the current through the lightbulb when a lightbulb is in series with a 2.0 ohm resistor is I = 1.78 A, 2.96 A.
More on resistors: https://brainly.com/question/30244234
#SPJ11
. the magnetic flux through a loop of wire is zero. can there be an induced current in the loop at this instant? explain
Yes, there can be an induced current in a loop of wire even if the magnetic flux through it is zero. This is because the induced current is not dependent on the magnitude of the magnetic flux, but rather on its rate of change.
What is Faraday's law of Electromagnetic induction?The Faraday's Law of Electromagnetic Induction states that an induced electromotive force (emf) is created in a conductor when there is a change in magnetic flux linkage with it. It means that any change in the magnetic field lines around a conductor can produce an induced current in it. This is called electromagnetic induction. For instance, when a magnet is moved towards a loop of wire, the magnetic field around the wire changes, leading to an induced current in the wire.
Similarly, when a wire loop is moved in a magnetic field, there is a change in the magnetic flux linkage with the loop, producing an induced current in it. Even if the magnetic flux through a loop of wire is zero, there could still be a change in the magnetic field around it, leading to an induced current. Therefore, the magnitude of the magnetic flux does not determine the presence of induced current, but its rate of change does.
Learn more about Electromagnetic induction here:
https://brainly.com/question/26334813
#SPJ11
which black hole is larger phounex a or ton 618
Answer:
Ton 618
Explanation:
Ton 618 is considered to be one of the largest known black holes, with an estimated mass of 66 billion times that of our sun. On the other hand, Phoenix A, also known as MRC 1138-262, is not a black hole but a galaxy cluster that contains a supermassive black hole at its center.
So, in terms of black hole size, Ton 618 is larger than Phoenix A since Phoenix A does not refer to a black hole but to a galaxy cluster.
black hole ton 618 is larger than phounex.
What is phounex and ton 618 ?Both Phoenix A and Ton 618 are quasars that are powered by supermassive black holes, but their black holes themselves have not been directly measured. Therefore, it is not currently possible to determine which black hole is larger based on direct observations.
However, the mass of the black holes in Phoenix A and Ton 618 can be estimated indirectly by studying the motion of stars and gas around them, among other methods. According to some estimates, the black hole in Ton 618 has a mass of around 66 billion times the mass of the Sun, while the black hole in Phoenix A has a mass of around 20 billion times the mass of the Sun. Therefore, based on these estimates, the black hole in Ton 618 is larger than the black hole in Phoenix A.
It is important to note that these estimates are subject to some uncertainty and may be revised as more data becomes available.
To know more about Black hole :
https://brainly.com/question/10597324
#SPJ2.
hydroelectric dams generate electricity by question 20 options: a. using the energy of the river to produce steam. b. using run-of-the-river systems, in which turbines are placed into the natural water flow. c. water impoundment, in which dam operators control the rate of water flow to turbines. d. using generators that are placed on the bottom of a river. e. converting the kinetic energy of the water impounded behind a dam into potential energy.
Hydroelectric dams generate electricity through water impoundment, in which dam operators control the rate of water flow to turbines.
c is the correct option.
Hydroelectric dams are dams used to produce electricity. The movement of water drives turbines, which power generators that generate electricity.
The movement of water, generated by gravity, is what drives turbines. Hydroelectric dams are the most widely used renewable energy source, accounting for approximately 16% of global electricity production.
Hydroelectric dams generate electricity through water impoundment, in which dam operators control the rate of water flow to turbines.
This is the process of using turbines that are powered by the movement of water that has been dammed to generate electricity.
Turbines are powered by water that has been dammed to generate electricity, which is then sent to a power station to be used.
The electricity generated from hydroelectric dams is clean and safe, making it an important part of the renewable energy mix. They are also an essential part of the global infrastructure because they provide reliable, low-cost power.
They also assist in the management of rivers, flood control, and irrigation systems in various parts of the world.
To know more about Hydroelectric dams: https://brainly.com/question/18776929
#SPJ11
a box of mass m sits on the floor of an elevator which is going down, and it is accelerating upward with constant non-zero acceleration of magnitude a. the magnitude of the normal force exerted on the box by the floor is nbf. the magnitude of the normal force exerted on the floor by the box is nfb. what is the correct relationship between nbfc and nfb ?
The correct relationship between the normal force exerted on the box by the floor (nbf) and the normal force exerted on the floor by the box (nfb) is nfb = nbf - mg, where g is the acceleration due to gravity and m is the mass of the box.
When the elevator is going down with an upward acceleration a, the net force acting on the box is given by:
Fnet = nbf - mg
where nbf is the normal force exerted on the box by the floor, and mg is the weight of the box.
Since the elevator is accelerating downwards, the magnitude of nbf must be less than the weight of the box (mg). Therefore, the net force on the box is downwards and given by:
Fnet = mg - nbf
However, we know that the box is also accelerating upwards with a non-zero acceleration a. Therefore, we can write another equation for the net force on the box:
Fnet = ma
Since the net force on the box must be the same in both equations, we can equate them:
ma = mg - nbf
Solving for nbf, we get:
nbf = mg - ma
We also know that the magnitude of the normal force exerted on the floor by the box (nfb) must be equal and opposite to nbf (i.e. nfb = -nbf). Therefore:
nfb = - nbf = - (mg - ma) = ma - mg
So the correct relationship between nbf and nfb is nfb = nbf - mg.
For more similar questions on normal force,
brainly.com/question/13340671
#SPJ11
A plane has an airspeed of 200 mph. The pilot wishes to reach a destination 900 mi due east, but a wind is blowing at 20. 0 mph in the direction 60. 0 ∘ north of east
The plane's heading is 4.61 degrees south of east, which is the direction the pilot needs to steer the plane in order to reach her objective and the trip takes 1.83 hours.
The airspeed of 200 mph can be broken down into its x and y components as follows: Vx = 200 mph * cos (0°) = 200 mph Vy = 200 mph * sin (0°) = 0 mph To solve this problem, we can break down the velocity vectors into their x and y components: The airspeed of 200 mph can be broken down into its x and y components as follows: Vx = 200 [tex]mph * cos (0°) = 200 mph Vy = 200 mph * sin (0°) = 0 mph[/tex]
The wind velocity of 20.0 mph at an angle of 60.0° north of east can be broken down into its x and y components as follows:[tex]Vwx = 20.0 mph * cos(60.0°) = 10.0 mph Vwy = 20.0 mph * sin(60.0°)[/tex] = 17.3 mph The resultant velocity vector is the vector sum of the airspeed and the wind velocity: Vrx = Vx + Vwx = 200 mph + 10.0 mph = 210 mpm Vry = Vy + Vwy = 0 mph + 17.3 mph = 17.3 mph
The speed of the plane relative to the ground is the magnitude of the resultant velocity vector:[tex]|Vr| = sqrt (Vrx^2 + Vry^2) = sqrt ((210 mph) ^2 + (17.3 mph) ^2) ≈ 211[/tex]mph The direction of the plane's velocity relative to the ground is given by the angle that the resultant velocity vector makes with due east:[tex]θ = atan(Vry / Vrx) = atan(17.3 mph / 210 mph) ≈[/tex] 4.7° north of east
To know more about Velocity:
brainly.com/question/28738284
#SPJ4
Complete question is :
A Plane Has An Airspeed Of 200 Mph. The Pilot Wishes To Reach Adestination 600 Mi Due East, But A Wind Is Blowing At 50 Mph In Thedirection 30o North Of Eastpart Ain What Direction Must The Pilot Head The Plane In Order To Reachher Destination? (2sig Figs)Part Bhow Long Will The Trip Take?(2 Sig Figs)Thanks!
a plane has an airspeed of 200 mph. the pilot wishes to reach adestination 600 mi due east, but a wind is blowing at 50 mph in thedirection 30o north of east
part A
in what direction must the pilot head the plane in order to reachher destination?
part B
how long will the trip take?
A ceramic mug is removed from a pottery kiln once the mug reaches a temperature of 700 degrees Celsius. The temperature of the mug then decreases at a rate given by r(t) = 20+100 arctan t / 1 + t degrees Celsius per minute, where t is the number of minutes since being removed from the kiln. What is the temperature of the mug, to the nearest degree Celsius, at time t = 10 minutes? A 15 B 288 C 412 D 685
The temperature of the mug which is removed from a pottery kiln is about 412°C. This can be calculated through integrating the decrease in temperature. Thus, the correct option is C.
What is the temperature of the mug, to the nearest degree Celsius, at time t = 10 minutes?A ceramic mug is removed from a pottery kiln once the mug reaches a temperature of 700 degrees Celsius. The temperature of the mug then decreases at a rate given by r(t) = 20+100 arctan t / 1 + t degrees Celsius per minute, where t is the number of minutes since being removed from the kiln.
The rate of decrease of temperature is given by:
`r(t) = 20 + 100 arctan t / 1 + t`
The rate of decrease of temperature is equal to the derivative of temperature with respect to time i.e.,
`dr(t)/dt = (d/dt) (T)`
On integrating the above equation, we get:
`T - T₀ = Integral of r(t) dt`
Here, T₀ is the initial temperature of the mug i.e., 700°C.
Substituting `T₀ = 700°C, t = 10` min and `r(t) = 20 + 100 arctan t / 1 + t`, we get:
`T = 412°C`.
Therefore, the temperature of the mug at time t = 10 minutes is 412°C.
Therefore, the correct option is C.
Learn more about Temperature here:
https://brainly.com/question/12085369
#SPJ11
A 0. 500 kg mass is oscillating on a spring with k=330 N/m. The total energy of its oscillation is 3. 24 J. What is the amplitude of the oscillation? (unit=m)
The required amplitude of the oscillation when mass, spring constant and total energy are given is calculated to be 14 cm.
The mass of the spring is given as 0.5 kg.
Spring constant is given as 330 N/m.
Total energy of the oscillation is given as 3.24 J.
The spring possesses only potential energy of its oscillation.
1/2 k x² = 3.24
where,
x = A, elongation of the spring is equal to amplitude
k is spring constant
Putting in the values,
⇒ 1/2 k A² = 3.24
⇒ k A² = 6.48
⇒ A² = 6.48/330 = 0.0196
⇒ A = 0.14 m = 14 cm
Thus, the required amplitude of the oscillation is calculated to be 14 cm.
To know more about amplitude:
https://brainly.com/question/22649183
#SPJ4
A car’s cooling system contains 25 kg of water. What is the increased change in temperature of the water if 872. 0 kJ of thermal energy is added?
When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.
Water's specific heat capacity (J/(gK), or 4,180 J/ (kgK). Thus, we can use the following formula to get the temperature change:
Q = mcΔT
where Q is the extra thermal energy (872 000 J), m the water mass (25 kg), c the water's specific heat capacity (4,180 J/(kg*K)), and T the temperature change.
When we solve for T, we get:
The equation T = Q/(mc) Equals 872,000 J/(25 kg * 4,180 J/(kgK)) = 35.0 °C.
When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.
learn more about energy here:
https://brainly.com/question/1932868
#SPJ4
a runner sprints around a circular track of radius 100 m at a constant speed of 7 m/s. the runner's friend is standing at a distance 200 m from the center of the track. how fast is the distance between the friends changing when the distance between them is 200 m? (round your answer to two decimal places.) m/s
The change in the distance between the friends changing when the distance between them is 200 m is 7.85m.
What is the distance?Consider a right-angled triangle with the radius of the circular track as one side of the right angle. Then the other two sides are the distance covered by the runner (in a single lap) and the distance between the runner and his friend.
Since the radius is perpendicular to the line connecting the friend and the center of the track, we can call it the hypotenuse of the triangle.
Let x be the distance between the runner and his friend. We are given that x = 200 m.Using the Pythagorean theorem, we can find the distance covered by the runner in a single lap of the track.
e can now differentiate the above expression with respect to time to find the rate of change of the distance covered by the runner (this will also be the rate of change of the distance between the runner and his friend).Hence,
2x(dx/dt) = 2 (distance covered by runner)(d(distance covered by runner)/dt)
dx/dt = (distance covered by runner)
(d(distance covered by runner)/dt) / x
Substituting x = 200 m and d(distance covered by runner)/dt = 7 m/s, we get:
dx/dt = (223.6 m)(7 m/s) / 200 m = 7.85 m/s.
Rounding off to two decimal places, we get:
dx/dt = 7.85 m/s.
Therefore, the answer is 7.85.
Read more about distance here:
https://brainly.com/question/26046491
#SPJ11
a hammer (mass 0.960 kg) rests on the surface of a table. what is the magnitude and direction of the force of the hammer pulling on earth? if the force acts upward, enter a positive value and if the force acts downward, enter a negative value.
The answer is: magnitude of the force = -9.408 N, direction of the force = downward.
A hammer of mass 0.960 kg is lying on a table. The magnitude and direction of the hammer pulling the earth can be determined from Newton's third law. The hammer applies an upward force to the table which is equal to the force of the table on the hammer.The hammer doesn't pull the earth, but the earth exerts an attractive gravitational force on the hammer. However, this force is negligible compared to the force exerted by the table on the hammer.
In this case, the force acting on the hammer is the force of gravity acting on it. The force of gravity, also known as weight, is given by: Fg = mg. Where
Fg is the force of gravity, m is the mass of the hammer, and g is the acceleration due to gravity.The acceleration due to gravity on the surface of the earth is approximately 9.8 m/s². Therefore:Fg = 0.960 kg × 9.8 m/s² = 9.408 N. The magnitude of the force of gravity acting on the hammer is 9.408 N. Since the force of gravity acts downward, the value should be entered as negative. Therefore, the answer is: magnitude of the force = -9.408 N, direction of the force = downward.
Learn more about acceleration due to gravity: brainly.com/question/88039
#SPJ11
a spiked collar that extends horizontally for up to 3 feet from the pole is an example of what kind of technology?
A spiked collar that extends horizontally for up to 3 feet from a pole is an example of an insulator used in electrical power transmission lines.
The spiked collar or a type of insulator that helps to hold the electrical power lines in place and prevent them from touching the poles, which could cause a short circuit. The collar is made of a non-conductive material such as porcelain, glass, or composite materials that do not conduct electricity.
The insulators are used in power transmission lines to provide electrical insulation between the conductor and the support structure, usually a pole or tower. They also serve to mechanically support the weight of the conductor, protect it from environmental factors such as moisture and pollution, and provide a clear and visible separation between the conductors and the support structure.
For more similar questions on electrical power transmission lines and insulators:
brainly.com/question/12147056
#SPJ11
2) what is r, the radius of curvature of the motion of the proton while it is in the region containing the magnetic field?
The radious of curvature of the motion of the proton while it is in the region containing the magnetic field is an important parameter that can be derived using the equations governing the motion of a charged particle in a magnetic field. This parameter is determined by the strength of the magnetic field and the velocity of the charged particle. The radius of curvature is defined as the radius of the circular path that the charged particle travels as it moves through the magnetic field.
The force on a charged particle moving through a magnetic field is given by the Lorentz force equation:
F = q (v × B)where F is the force, q is the charge of the particle, v is the velocity of the particle, and B is the magnetic field.
The force on a charged particle moving through a magnetic field is always perpendicular to both the magnetic field and the velocity of the particle. Therefore, the charged particle moves in a circular path with a radius of curvature r given by:
r = mv / qB
where m is the mass of the particle, v is its velocity, and B is the magnetic field strength.
In conclusion, the radius of curvature of the motion of the proton while it is in the region containing the magnetic field can be calculated using the equation r = mv / qB, where m is the mass of the proton, v is its velocity, and B is the magnetic field strength. This parameter is important in understanding the behavior of charged particles in magnetic fields and has many applications in fields such as particle physics, astrophysics, and plasma physics.
for such more questions on radious of curvature
https://brainly.com/question/29595940
#SPJ11
A 2100 kg truck has put its front bumper against the rear bumper of a 2400 kg SUV to give it a push. With the engine at full power and good tires on good pavement, the maximum forward force on the truck is 18,000 N. At this acceleration, what is the force of the SUV's bumper on the truck's bumper?
The force of the SUV's bumper on the truck's bumper is 20,568 N.
From the problem statement, the acceleration can be calculated by finding the force exerted on the system, i.e.
F= ma = 18000 Na
= 18000/(2100 + 2400)
= 2.31 m/s²
Therefore, the force of the SUV's bumper on the truck's bumper can be found by considering the forces involved in the system. The truck's force on the SUV is 18,000 N while the force of the SUV's bumper on the truck's bumper is to be found.
We can find the force using the Newton's third law of motion, which states that every action has an equal and opposite reaction.Thus, Force of SUV on truck's bumper = force of truck on SUV
= m₁*a₁= m₂*a₂
where, m₁= 2100 kg,
a₁= acceleration,
m₁= 2400 kg
Putting values,
2400 * a₁ = 2100 * 2.31
a₂ = 20.568 m/s²
Thus, Force of SUV on truck's bumper= m₁*a₂ = 2100 * 15.686= 32,841.06 N = 20,568 N.. (approximately). Therefore, the force of the SUV's bumper on the truck's bumper is 20,568 N.
Learn more about force and acceleration at: https://brainly.com/question/19414080
#SPJ11
The magnitude of the force between two point charges 1. 0 m
apart is 9 x 10°n. If the distance between them is doubled,
what does the force become?
Force will become 2.25 x 10^N. because, According to Coulomb's Law, the force between two point charges is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.
Thus, if the distance between two point charges is doubled, the force between them will decrease by a factor of 4. This is because the inverse square relationship means that the force decreases rapidly with distance. Therefore, if the force between two point charges is 9 x 10^N when they are 1 meter apart, when the distance is doubled to 2 meters, the force will become 9 x 10^N / 4 = 2.25 x 10^N.
To know more about Coulomb's Law, here
brainly.com/question/506926
#SPJ4
lab 4: newton's second law: the atwood machine pre-lab questions: 1. what happens to the acceleration of our system when the mass of the system increases but the net force stays constant? 2. what happens to the acceleration of our system when the net applied force increases but the mass of the system does not change? 3. explain, in your own words, potential sources of error in today's experiment.
According to Newton's second law, the acceleration of a system is directly proportional to the net force applied to it and inversely proportional to its mass. Therefore, if the net force stays constant but the mass of the system increases, the acceleration of the system will decrease.
Similarly, if the mass of the system remains constant but the net applied force increases, the acceleration of the system will increase.
There are several potential sources of error in the Atwood machine experiment. For example, friction in the pulley or air resistance could cause the system to accelerate at a different rate than predicted by theory. Additionally, the masses used in the experiment may not be perfectly accurate, which could introduce small errors into the measurements. The string connecting the two masses could also stretch or have varying elasticity, which could affect the results. Finally, human error in measuring the time or the distances traveled by the masses could lead to inaccuracies in the calculated values of acceleration or tension in the string.
for more such question on acceleration
https://brainly.com/question/10425898
#SPJ11
the fact that we observe neutrinos from the sun provides direct evidence of the fact that we observe neutrinos from the sun provides direct evidence of the existence of the solar wind. fusion in the sun's core. convection in the sun's interior.
The fact that we observe neutrinos from the sun provides direct evidence of the fact that we observe neutrinos from the sun provides direct evidence of fusion in the sun's core. This is because neutrinos are created as a result of nuclear fusion processes occurring within the sun's core.
Neutrinos are subatomic particles that are created in the nuclear reactions that occur within the sun's core. They are tiny, lightweight, and lack an electric charge. As a result, they can travel through matter, including the sun's interior, with relative ease without being deflected or absorbed. Fusion refers to the process of combining two atomic nuclei together to form a new nucleus. This process releases a tremendous amount of energy and is the driving force behind the sun's heat and light.
The sun fuses hydrogen nuclei into helium nuclei in its core, which releases energy in the form of light and heat. This process generates a tremendous amount of neutrinos, which stream out from the sun in all directions. The solar wind refers to a stream of charged particles, mostly protons and electrons, that are emitted by the sun's corona, it travels outwards through the solar system and can interact with the Earth's magnetic field, producing auroras and other phenomena. While neutrinos are not directly related to the solar wind, they are produced as a result of the same nuclear fusion processes that occur in the sun's core.
Learn more about solar wind at:
https://brainly.com/question/28227208
#SPJ11
We can test our stellar ages and models for the birth, evolution, and death of stars by determining if our observations of the metallicity within each component of the galaxy match our predictions. On the basis of how the life cycles of stars affect the composition of interstellar gas with time, rank the expected metallicities of the following components of our galaxy in order from lowest to highest.halo, bulge, thin disk
The rank order of expected metallicities, from lowest to highest, is Halo, Bulge, and Thin Disk.
The expected metallicities of the components of our galaxy, ranked from lowest to highest, are as follows:
1. Halo: The halo is the oldest component of our galaxy, consisting of old stars and globular clusters. It formed early in the galaxy's history when interstellar gas had low metallicity. Therefore, the halo is expected to have the lowest metallicity among the three components.
2. Bulge: The bulge is the central, densely packed region of the galaxy. It contains a mix of old and intermediate-age stars. The bulge formed through a combination of both primordial gas collapse and subsequent mergers.
3. Thin Disk: The thin disk is the relatively young and dynamically active component of our galaxy. It contains most of the young stars, star-forming regions, and open clusters.
The thin disk formed more recently from gas with a higher metallicity due to previous generations of star formation. As a result, the thin disk is expected to have the highest metallicity among the three components.
Know more about metallicity:
https://brainly.com/question/29404080
#SPj12
within the electromagnetic spectrum, visible light provides the energy for photosynthesis and has a
"Within the electromagnetic spectrum, visible light provides the energy for photosynthesis and has a wavelength range of approximately 400 to 700 nanometers (nm) "
This range of wavelengths is commonly referred to as the "visible spectrum" and includes colors from violet (at approximately 400 nm) to red (at approximately 700 nm). Photosynthesis is the process by which plants, algae, and some bacteria convert light energy into chemical energy, which is used to fuel the organism's metabolic processes. The pigments responsible for capturing light energy in photosynthesis are called chlorophylls. As a result, plants appear green to our eyes because they reflect green light and absorb other colors in the visible spectrum for photosynthesis.
To know more about electromagnetic spectrum, here
brainly.com/question/23727978
#SPJ4
--The complete question is, within the electromagnetic spectrum, visible light provides the energy for photosynthesis and has a wavelength range of ____________________"
An astronaut's pack weighs 17.5 N when she is on earth but only 3.24 N when she is at the surface of an asteroid.(a) What is the acceleration due to gravity on this asteroid?(b) What is the mass of the pack on the asteroid?
(a) The acceleration due to gravity on this asteroid is approximately 1.82 m/s². (b) The mass of the pack on the asteroid is approximately 1.78 kg.
What is gravity?Gravity is the force by which a planet or other body attracts objects toward its center. The force of gravity keeps all of the planets in orbit around the sun. Gravity exists between any two masses, any two bodies, any two particles. Gravity is one of the four fundamental forces of nature.
What is acceleration due to gravity?The acceleration due to gravity is the acceleration experienced by an object in freefall at the Earth's surface. It is represented by the symbol g. The acceleration due to gravity is always measured with respect to the Earth's surface.
How to calculate acceleration due to gravity?
The formula for the acceleration due to gravity is:
g = F / m
where F is the force due to gravity and m is the mass of the object experiencing the acceleration.
What is the formula for weight?The formula for weight is given by:
F = m x g
where F is the force due to gravity, m is the mass of the object, and g is the acceleration due to gravity.
We know that the acceleration due to gravity in Earth is 9.806 m/s², and the mass of the pack is constant whether on Earth or on the asteroid. Using the formula, we can calculate the mass of the pack.
m = F/g
m = 17.5 N / 9.806 m/s² ≈ 1.78 kg
Using this mass, we can calculate the acceleration due to gravity on the asteroid, given that the force or weight is 3.24 N.
g = F/m
g = 3.24 N / 1.78 kg ≈ 1.82 m/s²
Learn more about acceleration due to gravity here: https://brainly.com/question/28721569
#SPJ11