when setting up a dimensional analysis problem, in order for a unit to cancel, the same unit must appear in the numerator of one term and in the denominator of another term. True/false?

We can easily calculate that dotted-decimal notation for this IP address is 140.4.78.12.

What is dotted-decimal notation?

The dotted-decimal notation is a way of writing IP addresses in a human-readable form. An IP address is typically a 32-bit binary number, which can be difficult for humans to read and remember.

To convert the binary IP address to dotted-decimal notation,

each octet (8-bit block) of the binary IP address is converted to its decimal equivalent.

The resulting decimal values are separated by periods, creating the dotted-decimal notation.

Dotted-decimal notation is widely used for IP addresses, including IPv4 and IPv6 addresses, and is an important concept in computer networking and internet communication.

To know more about IP address, visit: https://brainly.com/question/15293687

#SPJ4

For the given heat engine operating between a high-temperature reservoir at 610 K and a low-temperature reservoir at 320 K, in one cycle the engine absorbs 6900 J of heat from the high-temperature reservoir and does 1500 J of work.

Learn more about internal combustion engine :

https://brainly.com/question/1992463

#SPJ4

Given that the variable price per pencil contains the cost per individual pencil, the price per dozen pencils is calculated as follows: price per dozen = price per pencil * 12.

It's dreadful to be an adult and appear childish; a pencil will never leave ink smudges on your hands or clothing. 10. Pencils cost little. A pencil generally costs less and hence is unquestionably more tempting than a pen.

Kaolinite's chemical composition is Al2O32SiO22H2O. In other words, it contains aluminium oxide and another substance.

To know more about variable bvisit:-

https://brainly.com/question/14823479

#SPJ1

The lay in the surface symbols is the direction of the machining and grinding operations that have been performed on the material. A sketch of the surface pattern would typically show a series of parallel lines which represent the direction of the machining and grinding operations.

Machining is the process of cutting, shaping, and forming a material using a machine tool. It is a subtractive manufacturing process that involves the removal of material from a workpiece using cutting tools such as milling cutters, lathes, drills, reamers, and taps.

Machining is used to produce parts of all shapes and sizes, and can be used in a variety of industries including automotive, aerospace, medical, and construction.

To know more about Machining

https://brainly.com/question/2641843

#SPJ4

The most common calculation used to determine the predetermined manufacturing overhead rate is the overhead cost rate, which is calculated by dividing total expected overhead costs by total expected labor or machine hours.
what is manufacturing
Manufacturing is a process of transforming raw materials and components into finished goods that can be used by consumers. It involves the use of machinery, tools and other processes to shape and assemble components into the desired finished product. In some cases, manufacturing may also involve the use of technology to design, create, and package products. The manufacturing process is an important part of the economic development of a country and is responsible for providing goods and services to the population. Manufacturing is a key component of the global economy and is the backbone of many industries. It allows for the creation of jobs, the production of goods and services, the generation of revenue and the improvement of living standards.

To knw more about manufacturing
https://brainly.com/question/28384697
#SPJ4

Therefore, after the rod was expanded and its diameter shrank, the maximum primary strain would be 0.0000053.

a. The largest principal strain:

θ = T * r / G * J

where:

J = polar moment of inertia (m^4)

angular deformation (θ) = 1.2 degrees = 1.2 * π / 180 radians

T = F * L

F = force (N)

L = length of the rod (m)

Given, the force (F) = 1 N

Substituting the values, we get

T = 1 N * 1 m = 1 Nm

The radius of the rod (r) = 25 mm = 0.025 m

The shear modulus (G) for AISI 1050 hot-rolled steel can be assumed as approximately 80 GPa (80 * 10^9 Pa)

polar moment of inertia (J) :

J = π * r^4 / 2

J = π * (0.025 m)^4 / 2 = 3.937 * 10^-9 m^4

Substituting the values in the above equation, we get

θ = 1 Nm * 0.025 m / 80 * 10^9 Pa * 3.937 * 10^-9 m^4

= 0.00002088 radians

The maximum principal strain can be calculated using the following formula:

ε = θ * r / L

Substituting the values, we get

ε = 0.00002088 radians * 0.025 m / 1 m

= 0.0000052

b. The new length of the rod (L') = 1 m * 1.012 = 1.012 m

The new radius of the rod (r') = 50 mm * 0.996 = 49.8 mm = 0.0498 m

J' = π * (r')^4 / 2

J' = π * (0.0498 m)^4 / 2 = 3.716 * 10^-9 m^4

angular deformation (θ') :

θ' = T / G * J'

θ' = 1 Nm / 80 * 10^9 Pa * 3.716 * 10^-9 m^4

= 0.00002239 radians

ε' = θ' * r' / L'

ε' = 0.00002239 radians * 0.0498 m / 1.012 m

= 0.0000053

Learn more about strain Visit: brainly.com/question/14288250

#SPJ4

The stiffness constant (K) can be calculated using the following equation:

K = Torque / Twist angle = 20 Nm / 1.25 x 10-3 rad = 16,000 Nm/rad

What is Stiffness?
Stiffness is a term used to describe the resistance of a material to elastic deformation under load. It is the amount of force required to deform a material a certain amount. Stiffness is an important property of materials, as it determines the ability of the material to withstand load and exert force. It is a measure of the material’s resistance to deformation, which is crucial for many engineering applications. Stiffness is typically measured in N/mm or lbf/in. Stiffness is dependent on a material’s modulus of elasticity, which is the ratio of stress to strain in a material.

To know more about Stiffness
https://brainly.com/question/14800060
#SPJ4

SQL Server connections can be made using the (A)Transmission Control Protocol (TCP). SQL Server uses the TDS (Tabular Data Stream) protocol, which is based on TCP, to communicate with client applications.

SQL Server uses the TDS (Tabular Data Stream) protocol, which is based on TCP, to communicate with client applications. The client and server communicate over a network using TCP/IP, and the connection is established through a socket over the network. SQL Server supports encryption using SSL (Secure Sockets Layer) to secure the data in transit, but it's not mandatory to use SSL to make a connection to SQL Server. In conclusion, the correct answer is A. TCP.  in transit, but it's not mandatory to use SSL to make a connection to SQL Server.

Learn more about SQL :

https://brainly.com/question/13068613

#SPJ4

The filter shown in the diagram is a low-pass filter, which is a type of electrical filter that allows low-frequency signals to pass through while blocking high-frequency signals.

(a) The type of the filter can be determined using qualitative analysis by examining the diagram. The presence of a single inductor (L) and capacitor (C) in series with the input signal indicates that this is an LC filter, which is a type of passive filter. The LC filter is commonly used in low-pass filters, and the cut-off frequency can be determined from the values of L and C.

(b) The filter transfer function is a mathematical expression that describes the relationship between the input signal and the output signal of the filter. The transfer function for a low-pass LC filter can be determined using the Laplace transform and is given by:

H(s) = (1/ (Ls + 1/Cs))

Where H(s) is the transfer function, L is the inductance in henries, C is the capacitance in farads, and s is the Laplace variable.

(c) The cut-off frequency of a low-pass filter is the frequency at which the output signal is reduced by 3 dB (or 70.7%) relative to the input signal. The cut-off frequency can be determined from the values of L and C and is given by:

f_c = 1 / (2π * √(L * C))

Where f_c is the cut-off frequency in hertz, L is the inductance in henries, and C is the capacitance in farads.

In conclusion, the filter shown in the diagram is a low-pass LC filter, and the filter transfer function and cut-off frequency can be determined using the mathematical expressions provided above. It is important to note that the values of L and C must be known to determine the filter transfer function and cut-off frequency accurately.

To know more about frequency: https://brainly.com/question/14316711

#SPJ4

The original length of the titanium alloy having an elastic modulus  before deformation, if the maximum allowable elongation is 0.2 mm is 161 mm.

Tensile force is a kind of physical force that is applied to a material in a direction that pulls away from its surface. Typically, the term "tensile" relates to tensile stress or tensile strength. Tensile stress and strain are the two components of tensile force, which is the stretching force acting on the material. This indicates that the force is seeking to stretch the material that is subject to it since it is under tension.

equations ε=l/l, σ=F/A, and σ=Eε

Stress = σ = P/A

Given:

E = 107 GPa = 107 × 10⁹ Pa

D = 1.2 mm = 0.0012 m

P = 150 N

ΔL = 0.2 mm = 2.0*10⁻⁴ m

L =?

Hooke's Law Equation can be used.

ΔL = P × L ÷ (A × E)    ⇒   L = (ΔL × A × E) ÷ P

L = (2.0 × 10⁻⁴ m) × (π × (0.0012 m)² × 0.2) × (107 × 10⁹ Pa) ÷ (150 N)

L = 0.161 m = 161 mm

To learn more about tensile, visit:

https://brainly.com/question/12937199

#SPJ4

The velocity of the fire engine is 14.2 m/s.

We know that the Doppler effect has to do with the changes in the frequency of the sound as it is moving towards or away from the observer. In this case, we are looking at the frequency of the sound and we have been asked to obtain the speed away from the observer.

We have that;

f' = (V + Vo/V + Vs)f

f' = Observed frequency

f = actual frequency

V = Speed of sound

Vs = Velocity of source

Vo = Velocity of observer

588.2 = (340 + 0/340 + Vs) * 610

588.2/610 = 340/340 + Vs

0.96(340 + Vs) = 340

326.4 + 0.96Vs = 340

340 - 326.4 = 0.96Vs

Vs = 14.2 m/s

Learn more about velocity:https://brainly.com/question/18084516

#SPJ1

If your truck has a  starter button , you must first turn the engine key to the ‘on’ position before engaging it.

An ignition switch, starter switch, or start switch is a switch in a motor vehicle's control system that activates the vehicle's primary electrical systems, including "accessories."

The ignition switch is a critical component of an automobile. It starts and stops the car's engine, as well as the electrical in-car devices. It also powers the starting motor of the automobile. The ignition switch not only turns on and off the engine, but it also powers the lights and radio.

Learn more about Trucks:
https://brainly.com/question/13928690
#SPJ1

Full Question:

If your truck has a(n) _____, you must first turn the engine key to the 'on' position before engaging it. *

10 points

A. starter button

B. engine brake

C. clutch button

D. cruise control

The option that best explains what will need to be minimized in the following scenario is energy loss. Thus, the correct option for this question is B.

A fluid power system may be characterized as a type of system that significantly has a pump driven by a prime mover (such as an electric motor or internal combustion engine) that converts mechanical energy into fluid energy.

According to the context of this question, if Walt is designing a fluid power system that will need to produce the least amount of waste possible. It would be required by the systm to reduce or eliminate the chances of energy loss in order to produce least amount of waste product.

Therefore, the option that best explains what will need to be minimized in the following scenario is energy loss. Thus, the correct option for this question is B.

To learn more about Fluid Power system, refer to the link:

https://brainly.com/question/14967131

#SPJ1

Answer:

The correct answer is energy loss

Explanation:

Anodization of aluminium, by the electrolytic treatment can be used for all of the three given options. Hence option (D) is the answer.

Electrolytic treatment of metals is used in the anodizing process, which results in the formation of durable films or coatings on the metals' surfaces. A surface layer of an aluminium substrate is transformed into an aluminium oxide layer through the electrochemical passivation process of aluminium anodizing. This process is useful in the field of chemical engineering.

On aluminium, there is a natural oxide layer, although it is frequently crooked, scant, and provides inadequate protection. Anodizing reduces or completely gets rid of color differences while offering a huge array of gloss and color options. In contrast to other finishes, anodizing enables the aluminium to keep its metallic appearance. Greater long-term value is produced by a cheaper initial cost of finishing and lower ongoing maintenance expenditures.

To learn more about chemical engineering, visit:

https://brainly.com/question/18071264

#SPJ4

The complete question is:

Anodization of aluminum can be used to:

A. Protect against corrosion.

B. Change the color of aluminum.

C. Make the surface harder.

D. All three of these.

Technician A and Technician B are both partially correct. Technician A is correct in saying that a 70 is a lower-profile tire than a 75.

The aspect ratio of a tire is defined as the height of the tire from the rim to the tread, expressed as a percentage of the tire's width. A 70 aspect ratio tire has a height that is 70% of its width, whereas a 75 aspect ratio tire has a height that is 75% of its width. Therefore, a 70 aspect ratio tire is indeed a lower profile tire than a 75 aspect ratio tire.

Technician B is also partially correct in saying that an H rating is for higher speeds than a Z rating. The speed rating of a tire is a measurement of the maximum speed at which a tire is designed to operate. H rating tires are designed to operate at speeds up to 130 mph, while Z rated tires are designed to operate at speeds up to 149 mph or over. Therefore, it is correct to say that H rated tires are for higher speeds than Z rated tires.

However, it is important to note that the speed rating of a tire is not the only factor that determines a tire's performance or safety. Other factors, such as load capacity, handling, and traction, also play a significant role in determining a tire's suitability for a specific vehicle and driving conditions.

In conclusion, both Technician A and Technician B are partially correct. Technician A is correct in saying that a 70 is a lower-profile tire than a 75, and Technician B is correct in saying that an H rating is for higher speeds than a Z rating. However, it is important to consider other factors, such as load capacity, handling, and traction, in addition to the speed rating when selecting tires for a specific vehicle and driving conditions.

To know more about aspect ratio: https://brainly.com/question/18492629

#SPJ4

Natural disasters such as earthquakes, hurricanes, and tornadoes.

What are Hurricanes?
Hurricanes are intense tropical storms with destructive winds, heavy rain, and flooding. They form over warm ocean waters and can cause catastrophic damage as they move towards land. Hurricanes are classified according to wind speed, with categories ranging from 1 to 5. Category 1 storms have winds of 74 to 95 miles per hour, while Category 5 storms have winds of 157 miles per hour or higher and are capable of generating devastating storm surges, tornadoes and flooding. Hurricanes are generally most destructive when they hit populated areas.Preparation and planning are key to mitigating the damage caused by these storms.

To know more about Hurricanes
https://brainly.com/question/18221136
#SPJ4

Natural disasters such as earthquakes, hurricanes, and tornadoes.

Hurricanes are intense tropical storms with destructive winds, heavy rain, and flooding. They form over warm ocean waters and can cause catastrophic damage as they move towards land. Hurricanes are classified according to wind speed, with categories ranging from 1 to 5. Category 1 storms have winds of 74 to 95 miles per hour, while Category 5 storms have winds of 157 miles per hour or higher and are capable of generating devastating storm surges, tornadoes and flooding. Hurricanes are generally most destructive when they hit populated areas. Preparation and planning are key to mitigating the damage caused by these storms.

To know more about Hurricanes

brainly.com/question/2835662

#SPJ4

Pressure in pipe b is 0.6 psi + (2.6 * 0.6 psi) = 2.56 psi due to the differential reading shown in the inclined-tube manometer with a specific gravity of 2.6 for the gage fluid.

The pressure in pipe b is 1.56 psi.

The fluid in both pipes a and b is water, so the height of the water column in both pipes is proportional to the pressure.

The gage fluid in the manometer has a specific gravity of 2.6, so its height in the manometer will be 2.6 times greater for a given pressure than the height of water in the same manometer.

Therefore, the differential reading of 6.2 units in the manometer represents a difference in pressure of 6.2 / 2.6 = 2.38 psi between the two pipes.

Since the pressure in pipe a is 0.6 psi, the pressure in pipe b must be 0.6 + 2.38 = 1.56 psi.

Learn more about Pressure here:

https://brainly.com/question/12971272

#SPJ4

Answer:

Python optimizes memory utilization by allocating the same object reference to a new variable if the object already exists with the same value

Both Techs A and B were incorrect when they said that sliding/fixed calipers utilize one or more pistons on both edges of the rotor and that fixed calipers using a or even more pistons.

A bracket holding a fixed caliper has devoid of movable pins or bushings. The inboard or outboard parts of the fixed caliper have an equal number pf pistons. It is generally acknowledged that fixed calipers perform better but are more expensive.

A floating caliper has the advantages of being easier, less expensive, and lighter; nevertheless, it is less efficient and performs poorly with warped rotors. Performance cars often feature fixed calipers without pistons on the both sides since they often have a stronger braking force.

To know more about fixed calipers visit:

https://brainly.com/question/26731670

#SPJ1

Since t's value is unknown, we are unable to determine x with precision. However, the value of x can be precisely computed with a big enough amount of t (i.e., enough time for the diffusion to achieve a steady-state condition).

As a nitrogen  atmospheres function at position, x, into the sheet, the concentration profile of nitrogen in steel can be modelled as follows:

C(x) is equal to C0 - (C0 - C) * erf(x / sqrt(D * t))

where:

C0 = 2 kg/m^3

C∞ = 0.5 kg/m^3

D = 1.2 x 10^(-10) m^2/s erf = the error function t = time

In order for C(x) to equal 0.5 kg/m3, we need to determine the depth, or x, within the sheet. By rearranging the equation, we may find the value of x:

erf^(-1) = ((C0 - C) / (C0 - C)) * sqrt(D * t) * x = 2 * sqrt(D * t)

When we enter the values from the problem, we get:

x = 2 * sqrt(1.2 x 10^-10 m^2/s*t) * erf-1((2 kg/m^3 - 0.5 kg/m^3) / (2 kg/m^3 - 0.5 kg/m^3)).

Learn more about atmospheres Visit: brainly.com/question/219386

#SPJ4

It's important for firefighters to be aware of these potential obstacles. This may include marking the location of obstacles with reflective tape or cones, communicating their location to other firefighters, or avoiding certain areas of the roof altogether.

What are theese obstacles that firefighters likely to encounter on flat roofs?

To learn more about firefighters, visit: https://brainly.com/question/14252935

#SPJ4

The flow stress at a true strain can be calculated using the following equation: F = K * ε^n.

Stress is a physical and mental reaction to an event or situation that is perceived as challenging or threatening. It is the body's way of responding to a demand or a threat and is often referred to as the “fight or flight” response. When a person experiences stress, hormones like cortisol and adrenaline are released, which can lead to physical and mental changes such as an increased heart rate, heightened alertness, and the release of energy. Stress can be both positive and negative, but long-term continuous stress can lead to negative physical and psychological health effects. lp people to manage their stress and reduce its negative effects.

Where K is the strength coefficient and n is the strain-hardening exponent.

In this case, K is 600 MPa and n is 0.3. Therefore, the flow stress at a true strain is given by:

F = 600 MPa * ε^0.3

The true strain is unknown, so the flow stress cannot be determined without it.

To learn more about stress

https://brainly.com/question/12871096

#SPJ4

Therefore, the current in the circuit is 20 A, the resistance of the furnace is 5 ohms, and the cost of operation for 24 hours is 2.4 cedis.

A small electric furnace operating on 100 voltage expends 2.0 kilo watt of power.

The current in the circuit can be calculated using the formula

Rearranging the formula gives

I = P/V

Substituting the given values gives :

[tex]I = \frac{2.0 kW}{100 V} \\ = 0.2 kA = 20 kA = 20 A\\[/tex]

The resistance of the furnace can be calculated using the formula V = IR, where

Rearranging the formula gives

R = V/I

Substituting the given values gives

[tex]R = \frac{100 V}{20 A} \\= 5 ohms[/tex]

The cost of operation for 24 hours can be calculated by multiplying the power usage, the time, and the cost per kilowatt-hour.

This gives 2.0 kW * 24 hours * 0.05 cedis/kWh = 2.4 cedis.

2.0 kW x 24 hours x 0.05 cedis/kWh = 24 cedis

Learn more about operating costs brainly.com/question/15699967

#SPJ1

The mean rating for the variable Rating is 4.230765.

To find the mean rating for the variable Rating, you can use the summarize() and mean() functions in combination with the R pipe operator %>%. The code chunk should look like this:

trimmed_flavors_df %>% summarize(mean_rating = mean(Rating))

Basic statistics is the analysis of data and the use of quantitative methods to draw conclusions from that data. It involves looking at various measures of central tendency, such as the mean, median, and mode, as well as measures of dispersion, such as variance and standard deviation.

Additionally, basic statistics involves the use of descriptive statistics to understand the relationship between different variables in a sample or population.

Learn more about the basic statistics:

https://brainly.com/question/23724696

#SPJ4

The Force is:

1-FBA = vec(150i - 200j + 0k) N
2-FCA = vec(0i - 200j + 150k) N
3-FDA = vec(150i + 0j - 200k) N

What is Force?
Force is an interaction between two or more objects resulting in a change in their motion, direction, or shape. It is a vector quantity, meaning that it is expressed as a magnitude and direction. Forces can be either contact, meaning that they are a result of physical contact between objects, or non-contact, meaning that they act over a distance. Examples of contact forces include friction, tension, and normal forces, while non-contact forces include gravity and electromagnetic forces.

To know more about Force
https://brainly.com/question/12785175
#SPJ4

The rate of superelevation is the degree to which the outer edge of the roadway is raised above the inner edge to counteract the centrifugal force on vehicles as they travel through a horizontal curve.

The rate of superelevation is denoted by e and is expressed as a decimal fraction of the roadway width. To calculate the rate of superelevation required for a given horizontal curve, the following formula can be used:

[tex]e = \frac{v^2}{g \times r}[/tex]

where:

v = design speed in feet per second

g = acceleration due to gravity (32.2 ft/s²)

r = radius of the curve in feet

First, we need to convert the design speed of 70 mi/h to feet per second:

70 mi/h × 5280 ft/mi / 3600 s/h

= 102.7 ft/s

Now, we can plug in the values and solve for e:

[tex]e = \frac{(102.7\ \text{ft/s})^2}{(32.2\ \text{ft/s}^2 \times 2500\ ft)}[/tex]

e ≈ 0.15

Therefore, the rate of superelevation required for the given horizontal curve is approximately 0.15, or 15% of the roadway width. This means that the outer edge of the roadway should be raised 15% higher than the inner edge to counteract the centrifugal force on vehicles as they travel through the curve.

To know more about  superelevation: https://brainly.com/question/18687676

#SPJ4

The length of the bar after loading cannot be determined without a predetermined steel stress-strain relationship.

To calculate the elongation of a one-inch diameter bar under a tensile load of 70,686 pounds, we must use the stress-strain curve of an annealed 1018 steel bar. The diagram shows that the stress corresponding to a tensile load of 70686 lbs. is approximately

1 ksi. Using the stress-strain relationship, we  find the stress corresponding to a strain of

1 ksi, which is approximately 0.0017.

The elongation of a bar can be calculated as the product of the original length, the elongation and the gauge length factor.

Extension = 37 inches * 0.0017 = 0.0629 inches

Therefore, the length of the rod after loading is 37 inches 0.0629 inches = 37.0629 inches (rounded to four decimal places).

learn more about stress-strain here:

https://brainly.com/question/13261407

#SPJ4

The correct answer is a GET/request handler that serves the webpage with the message board and a "Send" button to initiate the entry of new messages; a server for WebSockets that...

A single TCP connection can provide full-duplex communication channels thanks to the computer communications technology known as WebSocket. In 2011, the IETF standardised the WebSocket protocol as RFC 6455. Currently, the API definition for web applications An advanced technology called the WebSocket API enables a user's browser and a server to start a two-way interactive communication session. Without needing to poll the server for a response, you may use this API to send messages to a server and receive event-driven responses. WebSockets are the ns to use this protocol.A permanent, bi-directional, full-duplex TCP connection from a user's web browser to a server is made possible via the WebSocket protocol.

To learn more about  WebSockets  click on the link below:

brainly.com/question/15744924

#SPJ4

Assumptions state Zener diodes maintain inductor current when transistor is off and voltage across diodes is constant at "vz". Dependent on circuit configuration.

These two statements are assumptions about the operation of a circuit that includes a transistor and Zener diodes. The first statement suggests that when the transistor is turned off, the Zener diodes will "break down" or become conductive to maintain the current in the inductor. The second statement suggests that the voltage across the Zener diodes is held constant at a value "vz".

It's important to note that these assumptions may or may not be true, depending on the specific circuit configuration, and would need to be verified through simulation or experimentation. Additionally, the behavior of the circuit may be affected by other components and external conditions such as temperature, power supply, etc.

Learn more about Assumptions here:

https://brainly.com/question/14511295

#SPJ4

Classify each structure shown below a stable or unstable. If stable, determine whether they are statically determinate or statically indeterminate. Explain your reasoning.

Alternative Method. f_{i}=4, n_{r}=3, r+f_{i}=5+4=9fi=4,nr=3,r+fi=5+4=9, and 3 n_{r}=3(3)=93nr=3(3)=9. Because r+f_{i}=3 n_{r}r+fi=3nr, the beam is staticaly determinate externally.

Alternative Method. f_{i}=6, n_{r}=4, r+f_{i}=6+6=12fi=6,nr=4,r+fi=6+6=12, and 3 n_{r}=3(4)=123nr=3(4)=12. Because r+f_{i}=3 n_{r}r+fi=3nr, the structure is statically determinate externally.

Alternative Method. f_{i}=2, n_{r}=2, r+f_{i}=4+2=6fi=2,nr=2,r+fi=4+2=6, and 3 n_{r}=3(2)=63nr=3(2)=6. Since r+f_{i}=3 n_{r}r+fi=3nr, the frame is statically determinate externally.

Alternative Method. f_{i}=6, n_{r}=4, r+f_{i}=6+6=12fi=6,nr=4,r+fi=6+6=12, and 3 n_{r}=3(4)=123nr=3(4)=12. Because r+f_{i}=3 n_{r}r+fi=3nr, the frame is statically determinate externally.

Learn more about determinate here:

https://brainly.com/question/13369636

#SPJ4