what type of glove protects us from electrical sparks?

The flow rate of steam through the turbine is 1.28kg/s.

Steam enters the turbine at[tex]$3.5 \mathrm{MPa}$[/tex] and 500 degrees Celsius. The specific enthalpy is:

[tex]$$h_1=3451.7 \mathrm{~kJ} / \mathrm{kg}$$[/tex]

State 2

The steam exits the turbine at [tex]$0.3 \mathrm{MPa}$[/tex] and 200 degrees Celsius. The specific enthalpy is:

[tex]$$h_2=2865.9 \mathrm{~kJ} / \mathrm{kg}$$[/tex]

Now, let's determine the flow rate from the first law of thermodynamics.

[tex]& \dot{Q}-\dot{W}=\dot{m}\left[h_2-h_1\right] \\[/tex]

[tex]& \dot{m}=\frac{\dot{Q}-\dot{W}}{h_2-h_1}=\frac{0-(750 \mathrm{~kW})}{(2865.9-3451.7) \frac{k J}{\mathrm{~kg}}}\left[\frac{1 \frac{\mathrm{kJ}}{\mathrm{s}}}{1 \mathrm{~kW}}\right]=1.28 \mathrm{~kg} / \mathrm{s}[/tex]

[tex]$$\dot{m}=1.28 \mathrm{~kg} / \mathrm{s}$$[/tex]

To learn more about flow rate of steam  refer to:

https://brainly.com/question/13152847

#SPJ4

Given signal, [tex]$X_2(n)$[/tex] is periodic with Fundamental Period, [tex]$\mathrm{N}=40$[/tex]

A signal is said to be periodic signal if [tex]$x(n)=x(n+N)$[/tex]

Where, [tex]$\mathrm{N}$[/tex]= Fundamental Period

i.e., if[tex]$f=\frac{k}{N}$[/tex] where, [tex]$\mathrm{k} \& \mathrm{~N}$[/tex]both are integers

1. [tex]$X_1(n)=\cos (0.5 \pi n+0.3)$[/tex]

Sol: Consider Standard equation [tex]$x(n)=A \cos (\omega n+\theta)$[/tex]

Comparing given signal we get, [tex]$\omega n=0.5 \pi n$[/tex]

[tex]& \therefore 2 \pi f n=\frac{\pi n}{2} \\[/tex]

[tex]& \therefore f=\frac{1}{4}[/tex]

Result: Given signal, [tex]$X_1(\mathrm{n})$[/tex] is periodic with Fundamental Period, [tex]$\mathrm{N}=4$[/tex]

1.[tex]$X_2(n)=\cos (0.3 \pi n)+\sin (0.25 \pi n)$[/tex]

Sol: Consider [tex]$X_2(n)$[/tex]to be combination of [tex]$x_1(n) \& x_2(n)$[/tex]

Where, [tex]$x_1(n)=\cos \left(0.3 \pi n_1\right) \& x_2(n)=\sin \left(0.25 \pi n_2\right)$[/tex]

[tex]$\therefore \omega_1 n_1=0.3 \pi n_1 \& \omega_2 n_2=0.25 \pi n_2$[/tex]

[tex]$\therefore 2 \pi f_1 n_1=\frac{3}{10} \pi n_1 \quad \& \quad 2 \pi f_2 n_2=\frac{1}{4} \pi n_2$[/tex]

[tex]& \therefore f_1=\frac{3}{20} \& f_2=\frac{1}{8} \\[/tex]

[tex]& \therefore N_1=20 \quad \& N_2=8 \\[/tex]

[tex]& \therefore N=L C M o f N_1 \& N_2=40[/tex]

Given signal, [tex]$X_2(n)$[/tex] is periodic with Fundamental Period, [tex]$\mathrm{N}=40$[/tex]

To learn more about Fundamental Period refer to:

https://brainly.com/question/15684052

#SPJ4

B. A missing damper. and C. Soot and creosote buildup in the flue. are the conditions might cause a fireplace to smoke.

A fireplace that smokes can be caused by several conditions, including a missing damper and soot and creosote buildup in the flue.

A damper is a metal plate that controls the airflow in the flue and helps to regulate the fire. If the damper is missing, the airflow may be disrupted, causing the fire to smoke and producing a draft that pulls smoke and fumes into the room.

Soot and creosote are by-products of burning wood that can accumulate in the flue over time. If the buildup becomes too thick, it can restrict the airflow and cause the fire to smoke. Soot and creosote are also highly flammable, which can increase the risk of a chimney fire.

An undersized hearth can also be a factor in a fireplace that smokes. A hearth is the floor of a fireplace, and it needs to be large enough to accommodate the fire and prevent sparks and embers from escaping into the room. An undersized hearth may cause the fire to burn too hot, which can result in excessive smoke production.

Learn more about Soot here:

https://brainly.com/question/2333962

#SPJ4

The right response is B. When an aircraft is delayed and it is thought to have been in an accident, the NTSB must be alerted right away and as quickly as possible.

When: An aviation accident occurs or any of the circumstances listed below takes place, the operator of the aircraft must contact the closest National Transportation Safety Board (NTSB) Field Office as soon as possible and using the fastest method possible. a breakdown or malfunction of the flight control system. Any incident involving the operation of an aircraft that occurs between the time a passenger boards with the purpose to fly and the time they have all exited and in which someone is killed, has serious injuries, or the aircraft is damaged is referred to as an aircraft accident.

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

A blower compartment overheating due to natural convection can trigger a thermal overload switch to open, which is a safety component designed to protect the system from damage caused by excessive heat.

What is natural convection?

Natural convection is the flow of a fluid, such as air or water, caused by differences in density that result from temperature differences. This type of flow occurs without any external pumping mechanism and is driven solely by buoyant forces.

The warm fluid rises, creating an upward flow, while the cool fluid sinks, creating a downward flow, which creates a circulating flow pattern. Natural convection is an important phenomenon in many applications, including heating and cooling systems, and in many natural processes, such as Earth's atmosphere and ocean currents.

To know more about natural convection, visit: https://brainly.com/question/13002062

#SPJ4

The programming language C is all-purpose for computers. Dennis Ritchie came up with it back in the '70s, and it's still heavily utilized and important today.

// C program to demonstrate whether

// a number is prime or not using

// for loop

#include <stdio.h>

// defining the function

int primenumber(int number)

{

   int i;

   // condition for checking the

   // given number is prime or

   // not

   for (i = 2; i <= number / 2; i++) {

       if (number % i != 0)

           continue;

       else

           return 1;

   }

   return 0;

}

int main()

{

   int num = 7, res = 0;

   // calling the function

   res = primenumber(num);

   if (res == 0)

       printf("%d is a prime number", num);

   else

       printf("%d is not a prime number", num);

}

To learn more about C program refer to:

https://brainly.com/question/26535599

#SPJ4

Members BD, CE, and CD each had a force of 0 kN, 8.75 kN, and 6.25 kN.

What is force ?

A force is an effect that can alter an object's motion according to physics. A force can cause an object has mass to accelerate when it changes its velocity, for as when it moves away from rest. A way to describe force is as a push or a pull. A force is vector quantity because it has magnitude and direction. It is calculated using the newton (N). Force is denoted by the letter F. The net force acting on an object is equal to the speed at which its momentum varies over time, according to Second law of Newton in its original formulation.

To know more about force
https://brainly.com/question/13191643
#SPJ1

Answer:The magnetic field in a solenoid formula is given by, B = μoIN / L B = (1.26×10−6 × 15 × 360) / 0.8 B = 8.505 × 10−3 N/Amps m

Explanation:

The magnetic field generated by the solenoid is 8.505 × 10−4 N/Amps m.

Answer:

  255

Explanation:

You want to know the number of other 21-byte files that can have the same sha-1 hash code as a given file.

The SHA-1 hash algorithm produces a 20-byte message digest for its input. That is, there can be 2^160 possible different digests.

There can be 2^(21·8) = 2^168 possible different 21-byte files, so any given hash code may be repeated for (2^168)/(2^160) = 2^8 different files.

2^8 -1 = 255 other files may have the same SHA-1 hash.

__

Additional comment

If there is some regularity in the file structure that prevents the hash codes from being uniformly distributed, then the number of files with the same digest may well exceed 256.

Given a file a that is 21 bytes in length, SHA-1 or SHA256  other 21-byte files will produce the same sha-1 hash.

What is Hash Function?

Any function that may be used to map data of any size to fixed-size values is referred to be a hash function, while some haveh functions also enable variable length output. Hash values, hash codes, digests, or just hashes are the names given to the results of a hash function.

The SHA-1 hash function generates a 160-bit hash value from an input. Since the number of possible inputs is significantly larger than the number of possible 160-bit hash values, there can be multiple inputs that produce the same hash value, known as a hash collision.

The exact number of 21-byte files that will produce the same SHA-1 hash as a is unknown and depends on the specific input and the properties of the SHA-1 hash function. However, it is widely believed that collisions can be found for SHA-1 with a practical effort, so it is generally not considered secure for cryptographic purposes.

In short, if MD5 isn't strong enough to prevent collisions, use a stronger hash. If the stronger hashes are too slow, use a fast hash with a low chance of collisions, like MD5. Then, to further lower the likelihood of a collision, use a slower hash, like SHA-1 or SHA256. However, if SHA256 is quick enough and the doubled space isn't an issue, you should probably use SHA256.

Learn more about hash function click here:

https://brainly.com/question/14288937

#SPJ4

The  event type  you use when you want an input widget to trigger a microflow when it changes from 'no selection' to a specific selection A: "On Change".

In Mendix, "On Change" events are used to trigger a microflow when the value of an input widget changes. For example, if you have a dropdown list widget and you want to perform some action when the user selects an item from the list, you can set the "On Change" event for the widget.

Therefore,  "On Change" event triggers a microflow when the input widget changes from one value to another. In this case, when the input widget changes from "no selection" to a specific selection, the "On Change" event will trigger the microflow.

Learn more about  event type from

https://brainly.com/question/30407771

#SPJ1

Automatic transmission equipped vehicle should be placed in Drive. while manual transmission equipped vehicles should be placed in First gear.

To learn more about automatic transmission refer to:

https://brainly.com/question/14093047

#SPJ4

The student exerts the greatest force on the floor of the elevator when the elevator is at rest, either starting from the first floor or stopping at the tenth floor. When the elevator is in motion, the student is being acted upon by two forces: their weight, which is acting vertically downward, and the normal force from the floor of the elevator, which is acting vertically upward.

The normal force is equal in magnitude to the weight of the student but acts in the opposite direction. As a result, the net force acting on the student is zero and the student does not exert any significant force on the floor of the elevator.

However, when the elevator comes to a stop, the normal force changes. The sudden change in velocity means that there is a non-zero net force acting on the student, which results in the student exerting a force on the floor of the elevator. The magnitude of this force is equal to the student's weight, which is determined by their mass and the acceleration due to gravity.

In conclusion, the student exerts the greatest force on the floor of the elevator when the elevator is at rest, either starting from the first floor or stopping at the tenth floor. This is because the normal force changes when the elevator comes to a stop, resulting in a non-zero net force acting on the student and a corresponding force being exerted on the floor of the elevator.

To know more about force: https://brainly.com/question/13191643

#SPJ4

Cleavage describes a mineral's response to mechanical impact.

What is a mineral?

In terms of geology and mineralogy, a mineral or mineral species is typically defined as a pure, naturally occurring solid chemical compound with a fairly well-defined chemical composition.

The geological definition of a mineral typically excludes substances found only in living things. However, certain minerals are frequently biogenic or organic compounds in the sense of chemistry (such as calcite) (such as mellite). Additionally, inorganic minerals (like hydroxylapatite), which are also present in rocks, are frequently produced by living things.

The term "rock" differs from "mineral," which is defined as any bulk solid geologic material that is sufficiently large and homogeneous.

To know more about minerals, click the link given below:

https://brainly.com/question/18078524

#SPJ4

The correct answer is Science Physics Along the x-axis, there are two charges. Is it true that somewhere along the x-axis other than infinity, the net electric field always disappears

The physical field that surrounds electrically charged particles and exerts force on all other charged particles in the field, either attracting or repelling them, is known as an electric field (or E-field). It can also refer to a system of charged particles' physical field. A vector field and a starting position inside the field define the locus known as a "field line." We have electric field lines for the electric fields .Anywhere there is a voltage, there is an electric field. Anywhere there is a voltage, electric fields are produced around wires and equipment. You might consider.

To learn more about electric field click on the link below:

brainly.com/question/15800304

#SPJ4

direct-spark ignition system react when the room thermostat calls for heating

When the room thermostat calls for heating, a direct-spark ignition system will send an electrical signal to the furnace, which then triggers the main burner on the furnace to ignite.

An electrical signal is an oscillating electrical voltage or current used to transmit information, usually through a communication channel. It is a physical phenomenon produced by the flow of electric charges, usually through a conducting medium such as a wire. Electrical signals can be analog or digital depending on the type of information they carry.

This ignites the fuel and air mixture in the combustion chamber, which then heats the air that is circulated through the home. The furnace will remain on until the desired temperature set by the thermostat is reached.

To learn more about electrical signal
https://brainly.com/question/16783396
#SPJ4

To find the tension in the string and the acceleration of the block, we can use the equations of motion for the system.

Assuming the mass of the block M1 is 1500N and the mass of the block M2 is 1000N, the equation of motion for the system is given by:

T - μMgcos(θ) = M1a + M2a

Where T is the tension in the string, μ is the coefficient of friction between the block M1 and the inclined plane, Mg is the weight of the blocks, θ is the angle of the inclined plane, and a is the acceleration of the blocks.

Substituting the given values, we get:

T - 0.2(1500 + 1000)9.81cos(45°) = 1500a + 1000a

Simplifying, we get:

T = 6715N - 3000a

Solving for a, we get:

a = (6715 - T)/3000

Therefore, the acceleration of the block is given by (6715 - T)/3000, where T is the tension in the string.

Learn more about stress and acceleration:

https://brainly.com/question/13148167

#SPJ4

Answer: True.

Explanation:

You would not want to have an uneasy feeling clinic to host clients and staff. Put yourself in their shoes, would you want to visit an aesthetically pleasing clinic, or a barren looking one?

True, When constructing a clinic, the building should be as aesthetically pleasing and comfortable as possible to attract staff and clients.

What are the ways to Attract More Patients to Your Medical Practice?

1. Utilize online marketing: Use online marketing strategies such as SEO, content marketing, and social media marketing to increase the visibility of your medical practice.

2. Leverage referrals: Ask current patients to refer your practice to friends, family, and colleagues.

3. Develop a strong presence in the community: Participate in local health fairs, join community organizations, and attend events to increase your visibility.

4. Offer free medical services: Offer free medical services to underserved populations in the area to attract more patients.

5. Use patient feedback: Ask patients to complete surveys and provide feedback on their experience at your practice. Use this information to improve the patient experience and attract more patients.

Aesthetically pleasing and comfortable facilities can help attract staff and clients to a clinic. A pleasing design and comfortable environment can create an inviting atmosphere that encourages people to come in and use the clinic's services. Additionally, a pleasing and comfortable design can make it easier for staff to work in the clinic and provide quality care to clients.

Therefore, True is the correct answer.

To learn more about constructing a clinic from the link

https://brainly.com/question/30407400

#SPJ4

(a) Yes, the consensus AB is an implicant of the function f. An implicant is a product term that covers at least one minterm of the function. Since xA and x'B are both implicants, they must both cover at least one minterm of the function. When two implicants have the same variable values, it means that they both cover the same minterm, and their consensus is also an implicant.

(b) It is not necessarily a Prime Implicant. A prime implicant is an implicant that cannot be further reduced without losing any of the minterms it covers. The consensus AB may or may not be a prime implicant depending on whether it can be reduced further.

For example, if xA = x'y and x'B = xy, then their consensus AB = xy is a prime implicant, because it covers the same minterm as xA and x'B, but it cannot be reduced further.

However, if xA = x'y and x'B = x'y, then their consensus AB = y is not a prime implicant, because it can be reduced further to y' (or to 0).

Learn more about boolean algebra here: https://brainly.com/question/26659438

#SPJ1

Answer:

false

Explanation:

False (Statistical Process Control (SPC), moderate)

The purpose of process control is to detect when natural causes of variation are present.

False  The purpose of process control is to detect when natural causes of variation are present.

To learn more about Statistical Process Control refer to:

https://brainly.com/question/29318444

#SPJ4

The correct response is d. x + y. An example of a process is x+y.

A process is a group of choices and actions involved in how work is done. Processes are present everywhere and in every sphere of our lives, even if we may not be aware of them. Here are a few instances of processes: getting breakfast ready. making a purchase. Alternatively put, a process is an action or collection of actions that accepts inputs, adds value, and produces outputs for internal or external clients. The process is a collection of actions that communicate with one another. A process's output is frequently used as the input for another process. Any technique employees utilize to add value for the business is referred to as a work process. To complete tasks, businesses frequently develop internal or sector-specific work processes.

Learn more about process here

https://brainly.com/question/25453419

#SPJ4

The coefficient of friction at the floor is 0.02

To find the coefficient of friction at the floor, we need to calculate the force of friction acting on the ladder.

The force of friction acting on the ladder is equal to the force required to start the ladder sliding, which is given by:

f_friction = f_norm * μ

where f_norm is the normal force acting on the ladder and μ is the coefficient of friction.

The normal force acting on the ladder can be calculated using Newton's second law:

f_norm = m * g * cos(θ)

where m is the total mass of the ladder and man, g is the acceleration due to gravity and θ is the angle between the ladder and the horizontal (35° in this case).

So, combining the above two equations, we have:

f_friction = (25 + 75) * 9.8 * cos(35) * μ

f_friction = 100 * 9.8 * 0.819 * μ

f_friction = 818 * μ

Now, we can use the force of friction and the force required to start the ladder sliding to find the coefficient of friction:

f_friction = f_norm * μ

818 * μ = 0.2 * f_norm

μ = 0.2 * f_norm / 818

Substituting the values for f_norm and μ, we get:

μ = 0.2 * (100 * 9.8 * 0.819) / 818

μ = 0.02

So, the coefficient of friction at the floor is 0.02.

Learn more on frictional force here https://brainly.com/question/4618599

#SPJ1

You should wait until the traffic has cleared, and it is safe to make a left turn. Follow all traffic signals and use caution when making a left turn. Be sure to check for pedestrians and other vehicles in the intersection before making the turn.

When making a left turn at an intersection, it is important to exercise caution and follow the traffic signals. Before turning, one should be sure to check for any oncoming traffic, as well as pedestrians. If there is traffic present, one needs to wait until the traffic has cleared before making the turn. Additionally, it is important to ensure that there are no vehicles in the intersection that may impede the turn. Once it is safe to do so, it is important to signal the turn and proceed with caution. By taking these steps, one can ensure a safe and successful left turn at an intersection.

Learn more about traffic signals: https://brainly.com/question/24759367

#SPJ4

(a) To find the time when the velocity is again zero, we set the velocity equal to 0 and solve for t:

0 = v0 + at = 9t - 3t^3

Solving for t, we find that t = ±1.

(b) To find the position and velocity when t = 4 s, we first need to find the velocity equation by integrating the acceleration equation:

v = ∫a = ∫(9 - 3t^2)dt = 9t - t^3 + C

Using the initial condition v(0) = 0, we find C = 0 and

v(t) = 9t - t^3

Next, we integrate v(t) to find the position equation:

x = ∫v = ∫(9t - t^3)dt = 3t^2 - t^4 + C

Using the initial condition x(0) = 5, we find C = 5 and

x(t) = 3t^2 - t^4 + 5

Evaluating x(t) and v(t) at t = 4 s, we have:

x(4) = 3(4^2) - 4^4 + 5 = 51

v(4) = 9(4) - 4^3 = -36

(c) To find the total distance travelled by the particle from t = 0 to t = 4 s, we need to find the distance between the initial and final positions:

d = x(4) - x(0) = 51 - 5 = 46 ft

So the total distance travelled by the particle from t = 0 to t = 4 s is 46 ft.

The process of improving something within your game or production workflow is known as D. refining

When it comes to production workflow or a game console and its gameplay, in order to improve it, you would have to refine it and this can be done in a variety of ways.

It should be noted that the other options do not directly improve the game or the production workflow as they all have different meaning, hence, option D is correct.

Read more about production workflow here:

https://brainly.com/question/14293417

#SPJ1

Answer:

Explanation:

You want to know the deflection of the trace on an oscilloscope set to 5 V/div when it is connected to a 15 V DC power supply, both when the 'scope is set to DC input coupling, and when it is set to AC input coupling.

When the input coupling is DC, the input voltage difference from ground (or the reference level) will deflect the oscilloscope trace according to its sensitivity setting.

  15 V/(5 V/div) = 3 div

The trace will be deflected 3 divisions.

The oscilloscope will register any AC content that is within its bandwidth when the input coupling is set to AC. A good DC power supply will have no AC content, so the deflection of the trace will be zero, 0 divisions.

__

Additional comment

The trace may be deflected briefly, then settle back to zero, when a DC power supply is connected to a 'scope set for AC input. The act of connecting the supply provides a step-function input to the 'scope, which has an AC content. The duration of the deflection will depend on the time constant of the input circuit.

The correct answer is Nell lost both of her legs in a tandem bike accident many years ago, along with her husband Nagg. She currently resides next to Hamm's chair in a garbage can.

Because they lack legs, Nagg and Nell, Hamm's mother, are relegated to reside in trashcans. To Hamm and Clov's dismay, Hamm's parents, who are old, are always grumbling about not having enough food. Kelly Oury, a junior theatre major, faced acting difficulties when playing the role of Nell. Nagg: Hamm's legless father, who resides in a trash can. Nagg is kind and fatherly, yet he also feels grief and resentment about his son's lack of thanks. Nell: Nagg's neighbour and mother of Hamm, who is wheelchair-bound.

To learn more about Nagg click the link below:

brainly.com/question/3440324

#SPJ4

Answer:

5

Explanation:

If he plants in 36 feet half the bushes, then for 10 feet, 5 bushes he would plant. You could also use the rule of three.

The average labour cost incurred per month in manpower budget is 12.69 Rs.

Budgeting is the process of creating a plan to spend your money. This spending plan is called a budget. Creating a budget allows you to determine in advance whether you will have enough money to do the things you need to do or would like to do.

Average labour cost incurred per month in manpower budget = (100 x 2 + 200 x 25 + 250 x 2) / (100 + 200 + 250)
= (200 + 5000 + 500) / (450)
= 5711 / 450
= 12.69 Rs.
Therefore, the average labour cost incurred per month in manpower budget is 12.69 Rs.

To learn more about budget
https://brainly.com/question/29611383
#SPJ1

The power required to maintain the plane in flight is 120 ft/sec.

From the information, the model airplane flies at 49.9 mi/hr in level flight against a drag force of 1.65 lbf and we.eant to know the power that is required to maintain the plane in flight

Velocity will be:

= 49.9 × 1.4667

= 73.18 ft/sec

The force is given as 1.65

Therefore power will be:

= Force × Velocity

= 1.65 × 73.18

= 120 ft/sec

Learn more about power on:

brainly.com/question/1634438

#SPJ1

Answer: 7.00ft

Explanation: