what percentage of the sun's total mass is lost each year as a result of fusion converting mass into energy?

True. The surface finish produced by electrical discharge machining (EDM) often exhibits a cross-hatch pattern and has a roughness value typically ranging from 32 to 120 microinches.

The roughness value is a measure of the irregularities or variations in the surface texture, with a higher value indicating a rougher surface. The cross-hatch pattern is a result of the electrode's movement during the EDM process, leaving characteristic lines on the surface. This pattern can help improve lubrication and wear resistance in certain applications. However, it's important to note that the specific roughness values can vary depending on various factors such as the EDM parameters, electrode material, and the workpiece material.

Learn more about electrical here:

https://brainly.com/question/31951565

#SPJ11

The power for element (a) is -39 VA to two significant figures with the correct algebraic sign.

To compute the power for element (a), we can use the formula P = V * I, where P is power, V is voltage, and I is current.

Substituting the given values, we get:

P = (-13 V) * (3 A) = -39 W

Since the voltage is negative and the current is positive, the power is negative, indicating that the element is absorbing power rather than supplying it.

Expressing the answer to two significant figures and including the appropriate units, the power for element (a) is -39 W.

Learn more about element

brainly.com/question/13025901

#SPJ11

The required diameter for certified-capacity liquid rupture discs for the given conditions are 6.08 inches for 500 gpm, 3.07 inches for 100 gpm, 1.29 inches for 5 m/s, and 1.60 inches for 10 m/s.

To calculate the required diameter for certified-capacity liquid rupture discs for the given conditions, we first need to determine the burst pressure for each case. The burst pressure is calculated using the following formula:
Burst Pressure = Set Pressure + Overpressure - Backpressure
Using the specific gravity of 1.2 for all cases, we can calculate the burst pressure for each scenario as follows:
a. 500 gpm: Burst Pressure = 100 psig + 50 psig - 10 psig = 140 psig
b. 100 gpm: Burst Pressure = 100 psig + 50 psig - 5 psig = 145 psig
c. 5 m/s: Burst Pressure = 10 barg + 1 barg - 0.5 barg = 10.5 barg
d. 10 m/s: Burst Pressure = 20 barg + 2 barg - 1 barg = 21 barg
Once we have the burst pressure, we can use the specific gravity and the following formula to calculate the required diameter of the rupture disc:
Diameter = (Flow Rate * 60 * Specific Gravity) / (Burst Pressure * 0.8 * 3.14)
Where:
Flow Rate = Liquid flow in gallons per minute (gpm) or meters per second (m/s)
Specific Gravity = 1.2
Burst Pressure = Calculated burst pressure in psig or barg
Using the above formula, we can calculate the required diameter for each scenario as follows:
a. 500 gpm: Diameter = (500 * 60 * 1.2) / (140 * 0.8 * 3.14) = 6.08 inches
b. 100 gpm: Diameter = (100 * 60 * 1.2) / (145 * 0.8 * 3.14) = 3.07 inches
c. 5 m/s: Diameter = (5 * 60 * 1.2) / (10.5 * 0.8 * 3.14) = 1.29 inches
d. 10 m/s: Diameter = (10 * 60 * 1.2) / (21 * 0.8 * 3.14) = 1.60 inches
Therefore, the required diameter for certified-capacity liquid rupture discs for the given conditions are 6.08 inches for 500 gpm, 3.07 inches for 100 gpm, 1.29 inches for 5 m/s, and 1.60 inches for 10 m/s.

To know more about Specific gravity visit:

https://brainly.com/question/31485690

#SPJ11

the expression for the voltage VR across the resistor is VR = -(13.0V) * R/(L) cos((480rad/s)t) * t, where L is the inductance, R is the resistance, and t is the time

To derive an expression for the voltage VR across the resistor, we need to use Kirchhoff's voltage law, which states that the sum of the voltages around a closed loop in a circuit is zero. In this case, the loop includes the inductor and the resistor.
The voltage across the inductor is given as vL = -(13.0V) sin((480rad/s)t). We know that the voltage across a resistor is given by Ohm's law as VR = IR, where I is the current flowing through the resistor.
We can find the current flowing through the circuit by using the equation for the voltage across the inductor, which is vL = L(di/dt). We can rearrange this equation to find di/dt, which gives us the rate of change of the current. Thus, di/dt = (1/L) vL.
Substituting the given values, we get di/dt = -(13.0V)/(L) sin((480rad/s)t).
Now we can find the current flowing through the resistor as I = di/dt * t + I0, where I0 is the initial current when t=0. Since the current is alternating, we can assume that I0 = 0.
Therefore, I = -(13.0V)/(L) cos((480rad/s)t) * t.
Finally, we can find the voltage across the resistor as VR = IR * R. Substituting the expression for I, we get VR = -(13.0V) * R/(L) cos((480rad/s)t) * t. The amplitude of the voltage across the inductor is denoted by Vų, and the angular frequency is denoted by w.

To know more about voltage visit:

https://brainly.com/question/13521443

#SPJ11

The pendulum bob to reach its highest speed is 0.492 s.

A simple pendulum is a mass suspended from a fixed point by a string, which swings back and forth under the influence of gravity.

The time it takes for the pendulum to swing from one extreme to the other and back again (the period) depends on its length and the acceleration due to gravity. The longer the length, the slower the pendulum swings.

In this problem, we are given a simple pendulum of length 0.240 m that is pulled to the side through an angle of 3.50 degrees and released. To find the time it takes for the pendulum to reach its highest speed, we can use the formula for the period of a simple pendulum:

T = 2π√(L/g)

where T is the period, L is the length of the pendulum, and g is the acceleration due to gravity.

Using the given values, we can find that the period of the pendulum is 0.984 s. Since the time it takes for the pendulum to reach its highest speed is half of the period, the answer is 0.492 s.

If the pendulum is released at an angle of 1.75 degrees instead of 3.50 degrees, the length of the pendulum changes due to the trigonometry of the situation. Using the same formula, but with the new length, we can find the period to be 0.983 s. Therefore, the time it takes for the pendulum to reach its highest speed is 0.491 s, which is slightly shorter than the time for the larger angle.

Know more about pendulum here

https://brainly.com/question/29702798#

#SPJ11

The period of the wheel is 2.85 seconds and its angular speed is 2.20 rad/s.

To start, we need to convert the diameter of the wheel from cm to meters, as angular speed is typically measured in radians per second and period is measured in seconds.

213 cm = 2.13 m

Next, we can use the formula for period:

Period = time for one revolution

We know that it takes 2.85 seconds for each revolution, so:

Period = 2.85 s

Now, we can use the formula for angular speed:

Angular speed = 2π / Period

We just found the period to be 2.85 seconds, so:

Angular speed = 2π / 2.85 s

Angular speed = 2.20 rad/s

Therefore, the period of the wheel is 2.85 seconds and its angular speed is 2.20 rad/s.

To know more about angular speed, refer

https://brainly.com/question/1543128

#SPJ11

we can use the equation for the location of the bright fringes in an interference pattern:

tan(12.5°) = y/D y = D tan(12.5°) We also know the wavelength of the light is 449 nm, or 4.49 x 10^-7 m. Plugging in these values and solving for d: y = mλD/d D tan(12.5°) = λd d = λD / tan(12.5°) d = (4.49 x 10^-7 m)(D) / tan(12.5°) We don't know the distance from the slits to the screen, D, but we can assume it's on the order of a few meters. Let's say D = 2 m: d = (4.49 x 10^-7 m)(2 m) / tan(12.5°) d ≈ 1.11 x 10^-6 m So the spacing of the slits is approximately 1.11 μm.

Equation in science is a mathematical statement that expresses the relationship between two or more quantities. Equations can be used to describe natural phenomena, determine variable values, or solve problems. Equations usually consist of symbols that represent quantities, operators that indicate mathematical operations, and an equal sign (=) that indicates equality.

Learn More About Equation at https://brainly.com/question/17145398

#SPJ11

The claim can be that, Kinetic energy refers to the perpetual motion of molecules in a material.

A molecule's temperature and speed are exactly related to how much kinetic energy it has. Molecules acquire more kinetic energy when energy is introduced into a substance by heating, which causes them to move more quickly and raise temperature. This rise in temperature and speed may cause more frequent collisions and increased movement among molecules.

While molecules lose kinetic energy when energy is transported out of a substance through cooling, which causes them to travel more slowly and drop in temperature. The molecules may travel more slowly and experience fewer collisions as a result of the drop in temperature and speed. As a result, the freedom of motion of a substance's molecules can be significantly impacted by the passage of energy into or out of it.

Read more about Kinetic energy on:

https://brainly.com/question/25959744

#SPJ1

The high temperatures in the core of the sun come from immense gravitational force.

The Sun will expand to approximately 100 times its current size.

The Sun's final composition will be a cold, dense black dwarf, made up of carbon, oxygen.

The future of the Sun can be described as a continuous battle between the pressure created by fusion and the force of gravity. In the Sun's core, fusion occurs, converting hydrogen into helium and mass into energy in the form of gamma ray radiation. This fusion process creates immense pressure that counteracts the force of gravity trying to compress the Sun into a tiny sphere.

The high temperatures in the core, which enable fusion to occur, come from the immense gravitational force acting on the Sun's matter. As the Sun uses up its hydrogen fuel, it will enter different stages of its life cycle, expanding and shrinking in size.

Eventually, the Sun will exhaust its hydrogen fuel in the core and start burning hydrogen in a shell around the core. This will cause the Sun to expand into a red giant, becoming much larger than its current size. The outer layers will eventually be expelled, forming a planetary nebula.

As the core continues to contract under gravity, it will heat up and begin fusing helium into heavier elements, such as carbon and oxygen. Once the helium is exhausted, the core will no longer have sufficient pressure to counteract gravity, and the Sun will collapse into a white dwarf. Over time, the white dwarf will cool and become a black dwarf.

In summary, the Sun's life cycle involves a constant struggle between fusion pressure and gravitational force, which causes it to expand and contract through different stages.

The Sun's final composition will be a cold, dense black dwarf, made up of carbon, oxygen, and other heavier elements.

From afar, we would see the Sun expand to approximately 100 times its current size before shrinking back down to the size of a white dwarf.

To learn more about the Sun, visit:

https://brainly.com/question/28248963

#SPJ11

Therefore, the amount of energy that flows through the given area over the given time interval is 1.31 x 105 J.

To calculate the intensity of the electromagnetic wave, we can use the formula:
I = (1/2) * ε0 * c * E0^2
where I is the intensity, 0 is the permittivity of free space (8.85 x 10-12 F/m), c is the speed of light in a vacuum (3 x 108 m/s), and E0 is the electric field amplitude.
Substituting the given values, we get:
I = (1/2) * (8.85 x 10-12 F/m) * (3 x 10-8 m/s) * (91.5 V/m)
I = 3.93 x 10^-6 W/m^2
Therefore, the intensity of the electromagnetic wave is 3.93 x 106 W/m2.
To determine the amount of energy that flows through an area of 0.0229 m2 over an interval of 17.1 s, we can use the formula:
U = I * A * t
where U is the energy, A is the area, and t is the time interval.
Substituting the given values, we get:
U = (3.93 x 10^-6 W/m^2) * (0.0229 m2) * (17.1 s)
U = 1.31 x 10^-5 J
Therefore, the amount of energy that flows through the given area over the given time interval is 1.31 x 105 J.

To know more about electromagnetic wave visit:-

https://brainly.com/question/3101711

#SPJ11

The forecast error is |35 - 42| = 7. Forecast for next period = 0.8 * 42 + 0.2 * 35 = 39.2

The forecast error is calculated by subtracting the actual demand from the forecast, then taking the absolute value of the result. In this case,

To calculate the forecast for the next period using an exponential smoothing model with alpha = 0.8, we use the formula:  Forecast for next period = alpha * (last period's demand) + (1 - alpha) * (last period's forecast)

Substituting the given values, we get: Forecast for next period = 0.8 * 42 + 0.2 * 35 = 39.2

Rounding to the nearest whole number, the forecast for the next period using an exponential smoothing model with alpha = 0.8 is 39.

To know more about whole number, refer here:

https://brainly.com/question/29766862#

#SPJ11

For adenosine deaminase: the protein has a net charge of approximately +2 at pH 3.5.

For leucine: It will not migrate towards either electrode during electrophoresis.

For alanine: It will migrate towards the negative electrode during electrophoresis.

For superoxide dismutase: the protein has a net charge of approximately +1 at pH 4.3.

For glyceraldehyde-3-phosphate dehydrogenase: the protein has a net charge of approximately -0.25 at pH 6.1.

To calculate the net charge of a protein at a certain pH, we need to compare the pH to the protein's isoelectric point (pI). At the pI, the protein has a net charge of zero. At pH values below the pI, the protein is positively charged, and at pH values above the pI, the protein is negatively charged.

For yeast alcohol dehydrogenase:

At pH 4.6, which is below the pI of 5.4, the protein is positively charged. The net charge can be calculated using the Henderson-Hasselbalch equation:

pH = pKa + log([A-]/[HA])

where pKa is the dissociation constant of the protein, [A-] is the concentration of the deprotonated form of the protein, and [HA] is the concentration of the protonated form of the protein.

Assuming a pKa of 6.0 for yeast alcohol dehydrogenase, we can write:

4.6 = 6.0 + log([A-]/[HA])

Solving for [A-]/[HA], we get:

[A-]/[HA] = 0.00316

This means that the ratio of deprotonated to protonated forms of the protein is 0.00316. Since the deprotonated form has a negative charge, we can assume that the protein has a net charge of approximately +1 at pH 4.6.

For adenosine deaminase:

At pH 3.5, which is below the pI of 4.85, the protein is positively charged. Using the same method as above, assuming a pKa of 6.0 for adenosine deaminase, we get:

3.5 = 6.0 + log([A-]/[HA])

[A-]/[HA] = 0.001

This means that the protein has a net charge of approximately +2 at pH 3.5.

For leucine:

At pH 5.5, which is between the pI values of leucine (5.98) and alanine (6.01), we need to look at the side chain of the amino acid. Leucine has a non-polar side chain and is therefore uncharged at this pH. It will not migrate towards either electrode during electrophoresis.

For alanine:

At pH 4.3, which is below the pI of alanine (6.01), the protein is positively charged. It will migrate towards the negative electrode during electrophoresis.

For superoxide dismutase:

At pH 4.3, which is below the pI of 4.95, the protein is positively charged. Using the same method as above, assuming a pKa of 6.0 for superoxide dismutase, we get:

4.3 = 6.0 + log([A-]/[HA])

[A-]/[HA] = 0.00316

This means that the protein has a net charge of approximately +1 at pH 4.3.

For glyceraldehyde-3-phosphate dehydrogenase:

At pH 6.1, which is above the pI of 6.55, the protein is negatively charged. Using the same method as above, assuming a pKa of 6.0 for glyceraldehyde-3-phosphate dehydrogenase, we get:

6.1 = 6.0 + log([A-]/[HA])

[A-]/[HA] = 1.25

This means that the protein has a net charge of approximately -0.25 at pH 6.1.

For more question on protein click on

https://brainly.com/question/25155734

#SPJ11

Isoelectric point (pI) is the pH at which a molecule has no net charge and is stationary during electrophoresis. At pH values lower than pI, molecules will have a net positive charge, while at higher pH values, they will have a net negative charge. When given the pI and pH values, we can determine the net charge of a protein.

For example, yeast alcohol dehydrogenase will have a net positive charge at pH 4.6, while adenosine deaminase will have a net negative charge at pH 3.5. During paper electrophoresis, the direction in which a molecule migrates towards an electrode depends on its charge. For example, leucine will migrate towards the negative electrode at pH 5.5, while alanine will migrate towards the positive electrode at pH 4.3. Lastly, knowing the pI and pH values, we can determine the net charge of a protein, such as superoxide dismutase having a net positive charge at pH 4.3, and glyceraldehyde-3-phosphate dehydrogenase having a net negative charge at pH 6.1.

To learn more about isoelectric point click here: brainly.com/question/31609011

#SPJ11

In order to determine the velocity of the block at the instant θ=60°, we need to use the equation: v = rω. Where v is the velocity of the block, r is the distance between the block and the center of rotation, and ω is the angular velocity of link ab.

At the instant θ=60°, the distance between the block and the center of rotation is the length of link bc, which is given by: bc = 0.3m.

The angular velocity of link ab is given as: ω = 4rad/s.

Therefore, the velocity of the block at the instant θ=60° is: v = bc x ω = 0.3m x 4rad/s = 1.2m/s.

So, the velocity of the block at the instant θ=60° is 1.2m/s.

Read more about the Velocity of block.

https://brainly.com/question/31623770

#SPJ11

The equation describing the motion of a mass oscillating on a spring with a period of 0.89s and an amplitude of 5.9cm, starting at x=A at time t=0, is x = 5.9cos((2π/0.89)t).

The motion of a mass on a spring can be described by the equation x = Acos(ωt + φ), where A is the amplitude of the motion, ω is the angular frequency, t is time, and φ is the phase constant. The period (T) of the motion is given by T = 2π/ω. In this case, the period is given as 0.89s, so we can calculate the angular frequency as ω = 2π/T = 7.03 rad/s.

The mass starts at x=A, so the phase constant can be found using the initial condition x(0) = A, which gives φ = 0. Substituting the values of A, ω, and φ into the equation for motion, we get x = 5.9cos(7.03t).

Therefore, the equation describing the motion of the mass is x = 5.9cos((2π/0.89)t), which gives the position of the mass as a function of time.

To know more about angular frequency refer here:

https://brainly.com/question/30885221#

#SPJ11

Answer:

In a transverse wave, the matter is displaced perpendicular (at a right angle) to the direction of energy flow. Therefore, the correct answer is D.

Explanation:

90o - arcsin(n1/n2*sin(60o)). is the angle the transmitted beam makes with the horizontal axis is φ3,v.

Assuming the medium through which the violet beam is transmitted is isotropic, we can use Snell's law to find the angle of the transmitted beam.

Snell's law states that n1*sin(φ1) = n2*sin(φ2), where n1 and n2 are the refractive indices of the initial and final mediums, respectively, and φ1 and φ2 are the angles of incidence and refraction, respectively, measured with respect to the normal to the surface separating the two mediums.

In this case, the violet beam is incident at an angle of φ1,v = 60o with the horizontal axis. We can assume that the horizontal axis is parallel to the surface separating the two mediums, so the normal to the surface is also horizontal.

Let's assume that the refractive index of the medium through which the violet beam is incident is n1, and the refractive index of the medium through which the violet beam is transmitted is n2. Then, we can write:
n1*sin(φ1,v) = n2*sin(φ2,v)

Solving for φ2,v, we get:
φ2,v = arcsin(n1/n2*sin(φ1,v))

So, to find φ3,v, the angle the transmitted beam makes with the horizontal axis, we need to subtract φ2,v from 90o, since the transmitted beam will be perpendicular to the normal to surface separating the two mediums.

φ3,v = 90o - φ2,v

Substituting the given values, we get:
φ3,v = 90o - arcsin(n1/n2*sin(60o))

Note that we need to know the refractive indices of the two mediums to calculate φ3,v. Without that information, we cannot give a numerical answer.

To know more about Snell's law visit:

https://brainly.com/question/2273464

#SPJ11

The decay n - p + e- cannot happen then the conservation of energy, momentum, baryon number, and angular momentum would be violated. And the conservation of mass and lepton number would not be violated in this decay process.

The decay n - p + e- cannot happen because the conservation of several quantities is violated. Specifically, the conservation of baryon number and electric charge is violated, as the neutron (n) has a baryon number of 1 and no electric charge, while the proton (p) has a baryon number of 1 and a positive electric charge, and the electron (e-) has a baryon number of 0 and a negative electric charge. Additionally, the conservation of energy, momentum, and angular momentum would also be violated in this decay process. However, the conservation of mass and lepton number would not be violated in this decay process.

To learn more about decay  visit: https://brainly.com/question/11117468

#SPJ11

"Soil is any unconsolidated or weakly consolidated material at the earth's surface, regardless of particle size or composition."

Soil is a mixture of minerals, organic matter, air, water, and living organisms. consolidated material at the earth's surface, regardless of particle size or composition. It forms through the processes of weathering and the interaction of various factors such as climate, topography, parent material, organisms, and time. Soil plays a crucial role in supporting plant growth, providing nutrients, regulating water flow, filtering pollutants, and serving as a habitat for many organisms. It varies in composition and characteristics across different regions and has significant importance in agriculture, ecology, and land management.

Learn more about Soil is any unconsolidated or weakly here:

https://brainly.com/question/32282596

#SPJ11

a) The partial pressure of methane is 2.49 atm, ethane is 1.33 atm, and butane is 0.68 atm.

b) The total pressure of the mixture is 4.50 atm.

To calculate the partial pressure of each gas, we can use the ideal gas law equation:

PV = nRT

where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature in Kelvin.

First, we need to find the number of moles of each gas. We can use the formula:

moles = mass / molar mass

For methane (CH4):

moles(CH4) = 3.15 g / 16.04 g/mol = 0.196 mol

For ethane (C2H6):

moles(C2H6) = 3.15 g / 30.07 g/mol = 0.105 mol

For butane (C4H10):

moles(C4H10) = 3.15 g / 58.12 g/mol = 0.054 mol

Next, we can calculate the partial pressure of each gas using the ideal gas law:

P(CH4) = (moles(CH4) * R * T) / V

P(C2H6) = (moles(C2H6) * R * T) / V

P(C4H10) = (moles(C4H10) * R * T) / V

Assuming R = 0.0821 L*atm/mol*K and converting the temperature to Kelvin (64 °C = 337 K), and the volume is given as 2.00 L, we can substitute the values to calculate the partial pressures.

For methane (CH4):

P(CH4) = (0.196 mol * 0.0821 L*atm/mol*K * 337 K) / 2.00 L = 2.49 atm

For ethane (C2H6):

P(C2H6) = (0.105 mol * 0.0821 L*atm/mol*K * 337 K) / 2.00 L = 1.33 atm

For butane (C4H10):

P(C4H10) = (0.054 mol * 0.0821 L*atm/mol*K * 337 K) / 2.00 L = 0.68 atm

To calculate the total pressure of the mixture, we sum up the partial pressures of each gas:

Total pressure = P(CH4) + P(C2H6) + P(C4H10)

Total pressure = 2.49 atm + 1.33 atm + 0.68 atm = 4.50 atm

Learn more about methane here:

https://brainly.com/question/12645635

#SPJ11

False. The angle between the incident ray and the reflected ray in a convex mirror is not necessarily 20º. We cannot assure that at that point, the normal and the incident ray had a 10º angle.

In a convex mirror, the angle of incidence and the angle of reflection are measured with respect to the normal at the point of incidence. According to the law of reflection, the angle of incidence is equal to the angle of reflection. Therefore, if the angle between the incident ray and the reflected ray is 20º, it means that the sum of the angles of incidence and reflection is 20º. However, without more information, we cannot determine the exact angles of incidence and reflection in this scenario. It is not necessarily true that the normal and the incident ray had a 10º angle.

To know more about a convex mirror, click here;

https://brainly.com/question/3627454

#SPJ11

Star b must be 2 light years away. The apparent brightness of a star decreases with the square of the distance. Since star a appears 1/16 as bright as star b, star b must be √16 = 4 times closer, which is 2 light years away.

The apparent brightness of a star is determined by its intrinsic brightness, also known as its absolute magnitude, and its distance from the observer. In this scenario, star a and star b have the same absolute magnitude, indicating that they have the same inherent brightness. However, star a appears 1/16 as bright as star b. Since apparent brightness is inversely proportional to the square of the distance, we can deduce that star b must be 1/4 times the distance of star a to maintain the same apparent brightness. Given that star a is 4 light years away, star b must be 2 light years away. This ensures that the apparent brightness of star b is 1/16 of star a, as observed.

Learn more about absolute magnitude here:

https://brainly.com/question/30691550

#SPJ11

The angle between the polarizer and the analyzer is 39.2°.

The intensity of unpolarized light passing through a polarizing material is reduced by a factor of 1/2 since only one polarization direction is allowed to pass through. Thus, if the unpolarized light of intensity i0 passes through two polarizing materials, the intensity of transmitted light will be (1/2)*(1/2)*i0 = 0.25i0.

Since the transmitted intensity given in the problem is 0.30i0, it means that the second polarizing material is at an angle with respect to the first one. The intensity of transmitted light through two polarizing materials at an angle θ is given by I = (1/2)*i0*cos²θ.

Thus, 0.30i0 = (1/2)*i0*cos²θ, which implies that cos²θ = 0.6 or cosθ = √0.6. Taking the inverse cosine of both sides, we get θ = 39.2° (rounded to one decimal place).

Learn more about polarizer  here:-

https://brainly.com/question/31428863

#SPJ11

The volume of the balloon when it is submerged in the water and remains in equilibrium is 0.038 m^3. The pressure of the balloon at that point is 1.55 x 10^5 P

Since the system is in equilibrium, the weight of the balloon is equal to the buoyant force acting on it. The buoyant force is equal to the weight of the water displaced by the balloon. Hence, we can use Archimedes' principle to find the volume of the balloon when it is submerged and remains in equilibrium. We know that the density of water is 1000 kg/m^3 and the weight of the iron weight is 2.50 x 10^2 kg. Therefore, the weight of the water displaced by the iron weight is 2.50 x 10^2 kg x 9.81 m/s^2 = 2.4525 x 10^3 N. This is also equal to the weight of the balloon. Let the volume of the balloon when it is submerged be V. Then, the density of the balloon can be found using the mass and volume of the balloon. The mass of the balloon is negligible, so we can assume that the density of the balloon is the same as the density of the air inside it, which is approximately 1.29 kg/m^3. Therefore, the weight of the balloon is equal to the density of the balloon times the volume of the balloon times the acceleration due to gravity. Hence, we have 1.29 V x 9.81 = 2.4525 x 10^3. Solving for V, we get V = 0.038 m^3.

The pressure inside the balloon can be found using the ideal gas law, which relates the pressure, volume, and temperature of a gas. Since the temperature does not change with depth, we can assume that the temperature inside the balloon remains constant. Let P be the pressure inside the balloon at the point where it remains submerged. Then, the initial volume of the balloon is 0.500 m^3 and the initial pressure is atmospheric pressure, which is approximately 1.013 x 10^5 Pa. Using the ideal gas law, we have P x 0.500 = (1.013 x 10^5) x V. Substituting the value of V that we found earlier, we get P = 1.55 x 10^5 Pa. Hence, the pressure inside the balloon at the point where it remains submerged is 1.55 x 10^5 Pa.

Learn more about archimedes principle:

https://brainly.com/question/787619

#SPJ11

The magnitude of the electric field half way between two large, flat, horizontally oriented plates that are parallel to each other and a distance d apart is E. This is given in the question. However, if the separation of the plates is reduced to d2, we need to determine the new magnitude of the electric field half way between them. Option is b

To solve this problem, we can use the formula for the electric field between two parallel plates, which is E = σ/ε0, where σ is the surface charge density and ε0 is the permittivity of free space.When the plates are initially separated by a distance d, the surface charge density is spread over a larger area, resulting in a smaller magnitude of the electric field. However, when the plates are moved closer together to a separation of d2, the same amount of charge is now spread over a smaller area, resulting in a stronger electric field.

Therefore, the magnitude of the electric field half way between the plates when they are separated by a distance d2 is 2E, which is option c. This is because the surface charge density remains the same, but the area over which it is spread is reduced by a factor of 2. Hence, the electric field is doubled. Option is b.

For more such questions on electric field

https://brainly.com/question/19878202

#SPJ11

The magnitude of the electric field between two parallel plates is directly proportional to the distance between the plates.

Therefore, if the separation of the plates is reduced to d2, the electric field between them will increase. The new magnitude of the electric field half way between the plates can be calculated using the formula:
E2 = E x (d/d2)
where E is the original magnitude of the electric field and d and d2 are the original and new distances between the plates, respectively.
Substituting the given values, we get:
E2 = E x (d/d2) = E x (d/0.5d) = 2E
Therefore, the magnitude of the electric field half way between the plates is 2E. The answer is (c) 2E.

Calculating the magnitude of the electric field halfway between two large, flat, horizontally oriented plates when the separation is reduced to d2.
When the plates are a distance d apart, the electric field halfway between them has a magnitude E. If the separation is reduced to d2, the electric field will be inversely proportional to the separation. Since d2 is half of the original distance (d), the electric field magnitude will be twice as strong as before.
So, when the separation of the plates is reduced to d2, the magnitude of the electric field halfway between them will be 2E. The correct answer is c. 2E.

Visit here to learn more about electric field:

brainly.com/question/8971780

#SPJ11

The weight of the duck is 0.886 N and the buoyant force is 1.03 N.

We can calculate the  weight of the duck using the formula:

W=m*g; where 'm' is the mass of the duck and 'g' is the acceleration due to gravity.

And the mass of the duck can be calculated by the formula:

[tex]m= rho_d * V_d[/tex]

where [tex]rho_d[/tex] is the density of the duck and [tex]V_d[/tex] is the volume of the duck.

Now after substituting the values into the formula, we get:

[tex]m= (860 kg/m^3) * (0.000105 m^3)[/tex]

m= 0.0903 kg.

Similarly, the weight of the duck will be:

W=m*g

[tex]W=(0.0903 kg) * (9.81 m/s^2)[/tex]

W = 0.886 N

Now the buoyant force (F) can be calculated using the formula:

F = rho*V*g; where 'rho' is the density of the water, 'V' is the volume of the water displaced by the duck, and 'g' is the acceleration due to gravity.

We can say that the volume of the water that is displaced by the duck is equal to its own volume so

[tex]V_d = 0.000105 m^3[/tex]

Substituting the values, we get:

[tex]F = (1.0 * 103 kg/m^3) * (0.000105 m^3) * (9.81 m/s^2)[/tex]

F = 1.03 N

Therefore, the weight of the duck is 0.886 N and the buoyant force is 1.03 N.

Learn more about buoyant force at:

https://brainly.com/question/28464280

#SPJ1

Answer:

Geosynchronous

Explanation:

Quizlet

The given transverse wave is described by the equation y(x,t)=6.90 mm cos[2π(x(30.0 cm)-t(3.80×10−2 s))] to provide an explanation, this equation represents the displacement of the wave at a certain point (x) and time (t). The displacement is given by wavelength (30.0 cm) and τ is the period (3.80×10−2 s) of the wave.

The argument inside the cosine function represents the phase difference between the wave at two different points in space and time. As the wave propagates, this phase difference changes, causing the wave to oscillate with a certain frequency and wavelength. Overall, the equation y(x,t)=6.90 mm cos[2π(x(30.0 cm)-t(3.80×10−2 s))] describes the displacement of a transverse wave with a wavelength of 30.0 cm and a period of 3.80×10−2 s at a certain point (x) and time (t) transverse wave described by the equation y(x,t) = bcos[2π(x/l - t/τ)], where b = 6.90 mm, l = 30.0 cm, and τ = 3.80×10^-2 s.

The wave function for this transverse wave is y(x,t) = 6.90 mm * cos[2π(x/(30.0 cm) - t/(3.80×10^-2 s))]. 1. The given wave function is y(x,t) = bcos[2π(x/l - t/τ)]. 2. You have been given the values for b, l, and τ: b = 6.90 mm, l = 30.0 cm, and τ = 3.80×10^-2 s. 3. Replace the variables b, l, and τ with their respective values in the equation y(x,t) = 6.90 mm cos[2π(x/(30.0 cm) - t/(3.80×10^-2 s))].Now, you have the wave function for the given transverse wave with the provided values.

To know more about wavelength visit :

https://brainly.com/question/13533093

#SPJ11

The photon's energy in joules is 4.32 x [tex]10^{-13[/tex] J, and its frequency is 6.53 x [tex]10^{20[/tex] Hz.

To convert the energy of the gamma-ray photon from MeV to joules, use the conversion factor:

1 MeV = 1.602 x [tex]10^{-13[/tex] J.

Multiply the given energy by this factor:

2.70 MeV x 1.602 x [tex]10^{-13[/tex] J/MeV = 4.32 x [tex]10^{-13[/tex] J.

To find the frequency, use the Planck's equation:

E = hν,

where

E is energy,

h is Planck's constant (6.63 x [tex]10^{-34[/tex] J s), and

ν is the frequency.

Rearrange the equation to solve for frequency:

ν = E/h.

Substitute the energy in joules: ν = (4.32 x [tex]10^{-13[/tex] J) / (6.63 x [tex]10^{-34[/tex] J s) = 6.53 x [tex]10^{20[/tex] Hz.

For more such questions on frequency, click on:

https://brainly.com/question/254161

#SPJ11

The frequency of the gamma-ray photon is 6.53 x [tex]10^{20[/tex] Hz.

The energy of a gamma-ray photon can be converted from electronvolts (eV) to joules (J) using the conversion factor:

1 eV = 1.602 x [tex]10^{-19[/tex]J

Therefore, the energy of the gamma-ray photon with an energy of 2.70 MeV (mega-electronvolts) can be calculated as follows:

E = 2.70 MeV x 1,000,000 eV/1 MeV x 1.602 x [tex]10^{-19[/tex] J/eV

E = 4.33 x [tex]10^{-13[/tex] J

So the energy of the gamma-ray photon is 4.33 x [tex]10^{-13[/tex] J.

The frequency of the gamma-ray photon can be calculated using the equation:

E = hf

where E is the energy of the photon, h is Planck's constant (6.626 x 10^-34 J s), and f is the frequency of the photon. Rearranging this equation to solve for f, we get:

f = E/h

Substituting the value of E we just calculated and the value of h, we get:

f = (4.33 x[tex]10^{-13[/tex] J)/(6.626 x [tex]10^{-34[/tex] J s)

f = 6.53 x [tex]10^{20[/tex] Hz

Learn more about Planck's constant here:

https://brainly.com/question/30763530

#SPJ11

The period of a sound wave is the time it takes for one complete cycle of wave to occur. It is measured in seconds. To find the period of a sound wave, we can use formula: Period = 1/frequency.  Period of highest-frequency sound that can be heard is [tex]7.69×10^{-5}[/tex] seconds

Where frequency is the number of cycles per second, measured in Hertz (Hz). In this case, the highest-frequency sound that can be heard is 1.3×[tex]10^{-4}[/tex]. Therefore, the period can be calculated as:  Period = 1/1.3×[tex]10^{4}[/tex] Hz , Period = 7.69×[tex]10^{-5}[/tex] seconds This means that it takes 7.69×[tex]10^{-5}[/tex] seconds for one complete cycle of the highest-frequency sound that can be heard.

It is important to note that the human ear can only hear sounds within a certain range of frequencies, typically between 20 Hz and 20,000 Hz. Sounds with frequencies below 20 Hz are called infrasound, while sounds with frequencies above 20,000 Hz are called ultrasound. The period of these sounds will vary depending on their frequency.

In conclusion, the period of the highest-frequency sound that can be heard is 7.69×[tex]10^{-5}[/tex] seconds, which is the time it takes for one complete cycle of the sound wave to occur.

Know more about ultrasound here:

https://brainly.com/question/31609447

#SPJ11

The International Space Station (ISS) is a permanently-occupied outpost in outer space, and it is an important stepping stone for further space exploration.

The International Space Station (ISS) serves as a permanently-occupied outpost in outer space. It is a collaborative project involving multiple space agencies and serves as a crucial platform for scientific research, technological advancements, and international cooperation in space exploration. The ISS provides a unique environment for astronauts to live and work in microgravity conditions, conducting experiments across various fields such as biology, physics, astronomy, and human physiology. It also serves as a testbed for developing technologies and systems required for long-duration space missions, including those aimed at exploring the Moon, Mars, and beyond. The ISS has played a significant role in advancing our understanding of space, fostering international partnerships, and paving the way for future space exploration endeavors.

Learn more about International Space Station here:

https://brainly.com/question/13033832

#SPJ11