Using the two measured pipe lengths (L1= 66cm and L2=40 cm), work out the wavelength of the sound wave. use this to determine the mode nnumbers and speeds of sound that the two lengths correspond to. You can assume that L1 and L2 represent neighboring resonances (i.e, n and n+2). the pipes are open on one end and closed on the other. frequeny of tuning fork is 384 Hz.

The resistance in the original circuit is 21.66 Ω.

To find the resistance in the original circuit, we can use Ohm's Law (V = I * R) and the concept of series circuits.

Step 1: Calculate the voltage (V) in the circuit before adding the new resistor.
V_original = I_original * R_original

Step 2: Calculate the voltage (V) after adding the new resistor.
V_new = I_new * (R_original + R_added)

Since the voltage across the circuit remains constant, we can set V_original equal to V_new:

I_original * R_original = I_new * (R_original + R_added)

Now, we can plug in the given values and solve for R_original:

(13.6 A) * R_original = (10.3 A) * (R_original + 8.66 Ω)

After solving for R_original, we get:

R_original = 21.66 Ω

So, the resistance in the original circuit is 21.66 Ω.

To learn more about circuit, refer below:

https://brainly.com/question/27206933

#SPJ11

Part A:
The amplitude at a specific point on a vibrating string depends on its position within the standing wave pattern. In the third harmonic, there are three antinodes and two nodes between the fixed ends. As the distance from the left-hand end is 25.0 cm, this point is exactly at the first node, where the string doesn't oscillate. Therefore, the amplitude at this point is 0 cm.

Part B:
The time it takes for the string to go from its largest upward displacement to its largest downward displacement at a specific point is half of its period (T/2). The period can be calculated using the formula T = 1/frequency. With a frequency of 210 Hz, the period is:

T = 1/210 ≈ 0.00476 s

Half the period is 0.00476/2 ≈ 0.00238 s.

Part C:
At the given point, the amplitude is 0, so the maximum transverse velocity will also be 0 m/s.

Part D:
Similarly, the maximum transverse acceleration at this point will also be 0 m/s², as the amplitude is 0 and there is no oscillation.

Learn more about wave here:

https://brainly.com/question/30783512

#SPJ11

The displacement by 0.0050-N force is 4.2 mm.

Hooke's law states that the force required to stretch or compress a spring is directly proportional to the displacement of the spring from its equilibrium position. The proportionality constant is called the spring constant and is denoted by k. Mathematically, Hooke's law can be expressed as F = -kx, where F is the force applied to the spring, x is the displacement of the spring from its equilibrium position, and the negative sign indicates that the force exerted by the spring is in the opposite direction to the displacement.

Rearrange the formula to solve for x:

x = F / k

Substitute the values:

x = 0.0050 N / 1.20 N/m

x = 0.0041667 m

Convert meters to millimeters:

x = 0.0041667 m * 1000 = 4.1667 mm

Rounded to one decimal place,

The correct answer is c) 4.2 mm.

To know more about the displacement, click here;

https://brainly.com/question/30087445

#SPJ11

There are 4 lines that connect opposite corners of a cube through its center.

To find the number of lines that connect opposite corners of a cube through its center, we need to visualize the cube and draw a line connecting two opposite corners that pass through the center of the cube.

We can see that there are two diagonals passing through the center of the cube. Each diagonal connects two opposite corners of the cube. Therefore, the total number of lines that connect opposite corners of the cube through its center is equal to the number of diagonals, which is 4.

In summary, the number of lines that connect opposite corners of a cube through its center is 4.

To know more about center, visit;

https://brainly.com/question/28021242

#SPJ11

The final kinetic energy of the box is 12 Joules.

To calculate the work done on the box, we can use the formula:

Work = force x distance x cos(theta)

where theta is the angle between the force and the direction of motion. In this case, the force is 4N to the right and the displacement is also to the right, so theta is 0 degrees and cos(theta) is 1. Therefore:

Work = 4N x 3m x 1
Work = 12 Joules

So, the work done on the box is 12 Joules.

To find the final kinetic energy of the box, we can use the formula:

Kinetic energy = 0.5 x mass x velocity^2

We know that the mass of the box is 1.5kg and the initial velocity is 3m/s in the opposite direction. When the force is applied to the right, the box starts moving to the right and gains speed. We don't know the final velocity, but we can use the fact that the box ends up 3 meters to the right of where it started. If we assume that the force was applied over this entire distance, we can use the work-energy principle:

Work done by force = change in kinetic energy

We already calculated that the work done by the force is 12 Joules. We can assume that this work is used to increase the kinetic energy of the box. So:

12 Joules = final kinetic energy - initial kinetic energy

The initial kinetic energy is 0, since the box starts from rest. Solving for the final kinetic energy:

final kinetic energy = 12 Joules

So, the final kinetic energy of the box is 12 Joules.

Learn more about kinetic energy

brainly.com/question/26472013

#SPJ11

The deer's velocity after 5 seconds of hopping to the south will be 12.5 m/s. The initial velocity of the deer is not provided in the question, so we assume it to be zero.

Since the deer's velocity increases by 2.5 m/s each second, after 1 second, the velocity will be 2.5 m/s, after 2 seconds it will be 5 m/s, and so on. We can calculate the deer's velocity after 5 seconds by multiplying the rate of increase (2.5 m/s) by the time (5 seconds). Hence, the deer's velocity after 5 seconds will be [tex]\(2.5 \times 5 = 12.5\)[/tex] m/s.

In this case, we use the formula for uniformly accelerated motion: [tex]\(v = u + at\)[/tex], where v is the final velocity, u is the initial velocity, a is the acceleration, and t is the time. As the deer's initial velocity is assumed to be zero, the equation simplifies to v = at. Plugging in the given values of acceleration [tex](2.5 m/s\(^2\))[/tex] and time (5 seconds), we get [tex]\(v = 2.5 \times 5 = 12.5\) m/s[/tex]. Therefore, the deer's velocity after 5 seconds is 12.5 m/s.

To learn more about velocity refer:

https://brainly.com/question/29110645

#SPJ11

1.31 x 10^20 m/s^2  is the ratio of the speed v of an electron having this energy to the speed of light, c and 1.13 x 10^8 m/s would the speed be if it were computed from the principles of classical mechanics.

To determine the ratio of the speed v of an electron with kinetic energy of 7.50 x 105 eV to the speed of light, c, we can use the equation E = 1/2mv^2, where E is the kinetic energy of the electron, m is the mass of the electron, and v is its velocity.

Rearranging this equation, we get v = sqrt(2E/m).

Substituting the values, we get v = sqrt((2 * 7.50 x 10^5 eV) / (9.11 x 10^-31 kg)), which is approximately 1.63 x 10^8 m/s.

The speed of light is 2.99 x 10^8 m/s.

Therefore, the ratio of the electron's speed to the speed of light is 1.63 x 10^8 m/s ÷ 2.99 x 10^8 m/s = 0.544.

To compute the speed of the electron using classical mechanics,

we can use the equation F = ma, where F is the force acting on the electron,

m is its mass, and

a is its acceleration.

The force on the electron is given by F = eE, where e is the charge on the electron and E is the electric field.

Thus, the acceleration of the electron is a = eE/m.

Substituting the values, we get

a = (1.6 x 10^-19 C) (750 x 10^3 V/m) / (9.11 x 10^-31 kg)

= 1.31 x 10^20 m/s^2.

Using the equation v = at, where t is the time taken for the electron to traverse the potential difference,

we get

v = a(sqrt(2qV/m))/a

= sqrt(2qV/m)

= sqrt((2 x 1.6 x 10^-19 C x 750 x 10^3 V)/(9.11 x 10^-31 kg)),

which is approximately 1.13 x 10^8 m/s.

To know more about Kinetic energy visit:

https://brainly.com/question/26472013

#SPJ11

The frequency of the lowest frequency mode in a 3.00 m organ pipe that is open at both ends is 55.2 Hz.

The lowest frequency mode of a 3.00 m organ pipe open at both ends can be determined using the formula for fundamental frequency (f) of a tube open at both ends:

f = v / (2 * L)

where:
f = fundamental frequency (Hz)
v = speed of sound in air (331 m/s)
L = length of the pipe (3.00 m)

Using the given values, we can calculate the frequency:

f = 331 m/s / (2 * 3.00 m)
f = 331 m/s / 6.00 m
f = 55.17 Hz

Therefore, the frequency of the lowest frequency mode for a 3.00 m organ pipe open at both ends is approximately 55.17 Hz.

Learn more about frequency here:-

https://brainly.com/question/30783512

#SPJ11

The maximum ram force (p) that can be applied to the clamp at d is equal to the allowable normal stress (σallow) multiplied by the area (A) of the clamp at that location.

The maximum ram force (p) that can be applied to the clamp at d is determined by the allowable normal stress (σallow) for the material and the area (A) of the clamp at that point. The allowable normal stress represents the maximum stress that the material can withstand without permanent deformation or failure. By multiplying the allowable normal stress (σallow) by the area (A) of the clamp, we can find the maximum force (p) that can be applied. This ensures that the force exerted on the clamp does not exceed the material's strength and avoids any potential damage or failure.

Learn more about allowable normal stress here:

https://brainly.com/question/31984258

#SPJ11

An electromagnetic wave is generated by the initiation of current in a current sheet along the x direction in the zx plane at y=0. At t=0, a steady flow current is switched on.

When a current is initiated in a current sheet along the x direction in the zx plane at y=0, it generates an electromagnetic wave. This wave propagates in space and is characterized by an electric field and a magnetic field that are perpendicular to each other and also perpendicular to the direction of propagation.

At t=0, a steady flow current is switched on, which adds to the existing current in the current sheet. This causes a perturbation in the current, which in turn leads to the emission of radiation in the form of electromagnetic waves.

The electromagnetic wave generated by the current sheet can be described mathematically using Maxwell's equations. These equations relate the electric and magnetic fields to the sources that generate them, such as charges and currents. In the case of the current sheet, the current is the source of the electromagnetic waves.

The propagation of electromagnetic waves has many practical applications, such as in wireless communication, radar, and satellite communication. Understanding the physics of electromagnetic waves is crucial in the design and optimization of these systems.

Learn more about Electromagnetic wave

brainly.com/question/29774932

#SPJ11

The force applied to spring of spring constant 30 N/m is 150 N.

Force is the product of mass and acceleration. Force is a vector quantity and the S.I unit of force is Newton (N).

To caculate the force that is applied on the spring, we use the formula below

Formula:

Where:

From the question,

Given:

Substitute these values into equation 1

Hence, the right option is b) 150 N.

Learn more about force here: https://brainly.com/question/25573309

#SPJ1

The car's initial speed is 20 m/s, and its speed increases at a rate of 0.6s m/s² along the circular track.

The car's initial speed, v0, is given as 20 m/s. Along the circular track, its speed increases with time, denoted as s. The rate of this increase is given as at = 0.6s m/s², where s represents the distance traveled on the track in meters. As time passes, the speed of the car progressively accelerates according to the equation. For example, if s = 5 meters, the rate of speed increase would be 0.6 * 5 = 3 m/s². This equation describes the relationship between the distance traveled and the corresponding acceleration, determining how the car's speed evolves along the circular track.

learn more about speed here:

https://brainly.com/question/13262927

#SPJ11

In the Bohr model of the hydrogen atom, the potential energy of an electron in a particular orbit is given by the formula:

U = - (2.18 * 10^-18 J) / n^2

Where U is the potential energy, n is the principal quantum number representing the orbit.

To calculate the potential energy of the atom when it moves up to the next higher Bohr orbit, we need to consider the change in the principal quantum number.

Let's assume the initial orbit has a principal quantum number of n1, and the next higher orbit has a principal quantum number of n2 = n1 + 1.

The potential energy in the initial orbit is given as U1 = -1.20 * 10^-19 J.

Substituting these values into the formula, we have:

U1 = - (2.18 * 10^-18 J) / n1^2

U2 = - (2.18 * 10^-18 J) / (n1 + 1)^2

To find the potential energy in the next higher orbit, we can calculate U2 as:

U2 = - (2.18 * 10^-18 J) / (n1 + 1)^2

Now, we can substitute the given values and calculate U2:

U2 = - (2.18 * 10^-18 J) / (n1 + 1)^2

U2 = - (2.18 * 10^-18 J) / (n1^2 + 2n1 + 1)

Please provide the value of n1 so that we can calculate the potential energy in the next higher Bohr orbit.

Learn more about **Bohr model** and **potential energy** of hydrogen atoms here:

https://brainly.com/question/30401859?referrer=searchResults

#SPJ11

A) The thrust of the rocket is 889 N.
B) The rocket's change in velocity after burning 355 kg of fuel is 192.5 m/s.
C) The rocket's velocity after 171 s is 1239.7 m/s.

A) Thrust = mass flow rate * exhaust velocity = 0.0550 kg/s * 1650 m/s = 889 N

B) Use Tsiolkovsky rocket equation: Δv = ve * ln(m0 / m1), where Δv is change in velocity, ve is exhaust velocity, m0 is initial mass, and m1 is final mass. Δv = 1650 m/s * ln((1830 kg) / (1830 kg - 355 kg)) = 192.5 m/s

C) Calculate mass after 171 s: m = 1830 kg - (0.0550 kg/s * 171 s) = 1625.45 kg. Apply Tsiolkovsky rocket equation: Δv = 1650 m/s * ln((1830 kg) / (1625.45 kg)) = 211.7 m/s. Final velocity = initial velocity + change in velocity = 1028 m/s + 211.7 m/s = 1239.7 m/s.

To know more about exhaust velocity click on below link:

https://brainly.com/question/31322519#

#SPJ11

The rotational losses of the motor are 27,896.39 W, the full load power factor is 0.891, and the power transmitted to the rotor at full load is 91.57 kW. The rotor I2R losses at full load are 275.18 W. The output power at full load is 78.44 kW, and the efficiency at full load is 95.3%.

(a) The rotational losses can be calculated as follows:

No-load current = 42.2 A

No-load power = 3 x 230 V x 42.2 A x 0.9 (assumed power factor of 0.9 for no-load test) = 27,904.4 W

Stator copper losses at no-load = [tex]$3 \times (0.0422)^2 \times 15 \text{ m}\Omega$[/tex] = 8.01 W

Rotational losses = No-load power - Stator copper losses = 27,904.4 W - 8.01 W = 27,896.39 W

Therefore, the rotational losses are 27,896.39 W.

(b) The full load power factor can be calculated as follows:

Total power is drawn at full load = 82 kW

Full load current = 248 A

Output power = 3 x 230 V x 248 A x Power factor

Power factor = Output power / (3 x 230 V x 248 A) = 0.891

Therefore, the full load power factor is 0.891.

(c) The power transmitted to the rotor at full load can be calculated as follows:

Slip at full load = (1176 - 1176 x 0.891) / 1176 = 0.109

Output power at full load = 82 kW

Power transmitted to the rotor = Output power / (1 - Slip) = 91.57 kW

Therefore, the power transmitted to the rotor at full load is 91.57 kW.

(d) The rotor I2R losses at full load can be calculated as follows:

Rotor resistance per phase = Stator resistance per phase = 15 mΩ

Rotor I2R losses = [tex]$3 \times (248)^2 \times 15 \text{ m}\Omega$[/tex] = 275.18 W

Therefore, the rotor I2R losses at full load are 275.18 W.

(e) The output power and the efficiency at full load can be calculated as follows:

Output power can be calculated using the torque equation and the slip equation:

Torque at full load = (3 x 230 V x 248 A x 0.891 x (1 - 0.109)) / (2 x π x 60 Hz) = 355.5 Nm

Motor speed at full load = 1176 x (1 - 0.109) = 1050.8 rpm

Output power at full load = Torque x 2 x π x Motor speed / 60 = 78.44 kW

Efficiency at full load = Output power / Input power

Input power at full load = 3 x 230 V x 248 A x 0.891 = 82.3 kW

Therefore, the efficiency at full load is:

Efficiency = 78.44 kW / 82.3 kW = 0.953 or 95.3%

Therefore, the output power at full load is 78.44 kW and the efficiency at full load is 95.3%.

To learn more about power factor

https://brainly.com/question/31325309

#SPJ4

A current-carrying loop of wire is placed in a uniform b-field as shown. If the direction of the current of the loop is as indicated, the loop it will experience a torque that causes it to rotate.

When a current-carrying loop is placed in a uniform magnetic field, it will experience a torque that causes it to rotate. The direction of the rotation can be determined using the right-hand rule: if you point your right thumb in the direction of the current and your fingers in the direction of the magnetic field, the direction of rotation will be perpendicular to both the thumb and fingers.

To explain further, the torque on a current-carrying loop in a magnetic field is given by τ = NIABsinθ, where N is the number of turns in the loop, I is the current, A is the area of the loop, B is the magnetic field strength, and θ is the angle between the plane of the loop and the direction of the magnetic field. The amount of rotation will depend on the strength of the magnetic field and the current in the loop, as well as the shape and size of the loop itself. However, the direction of rotation will always be the same, given by the right-hand rule. So therefore if the loop is placed as shown and the current flows in the direction indicated, the torque will cause the loop to rotate clockwise.

To know more about magnetic field here

https://brainly.com/question/31323435

#SPJ11

The relationship between the path length difference dx and the wavelength lambda when the two waves interfere constructively at position P is given by dx = n * lambda, where n is an integer.

This means that the path length difference between the two waves must be an integer multiple of the wavelength for constructive interference to occur. When the two waves interfere destructively at position P, the relationship between the path length difference dx and the wavelength lambda is given by dx = (n + 1/2) * lambda, where n is an integer. This means that the path length difference between the two waves must be a half-integer multiple of the wavelength for destructive interference to occur.

When two sources of waves are coherent, it means that they have a constant phase relationship with each other, which means that they have the same frequency and wavelength. In the case of the waves in question 2, since they have the same amplitude, wavelength, and phase at positions S1 and S2, they are coherent.
If the sources in question 2 were two flashlights, interference would not be observed at position P because the light waves from the two flashlights would not be coherent. The light waves from the two flashlights would have different frequencies, wavelengths, and phases, which would result in a random pattern of light at position P rather than interference.

To know more about wavelength visit:

https://brainly.com/question/31143857

#SPJ11

Identify the object's density. Continue to the next step if you know the object's density. If not, you might need to compute it using the object's mass and volume.

Find out the fluid's density. It is important to understand the fluid's density in which the object is floating. Verify the densities. An object will float if its density is lower than that of the fluid. In the case of equal densities, the object will float in a neutral manner.

According to Archimedes' principle, an object's buoyant force is equal to the weight of the fluid it is dislodging. Apply this idea to determine the buoyant force.

To know more about object's density, here

brainly.com/question/6838128

#SPJ4

The half-life of the isotope is 2.37 days.

The half-life (T1/2) of the isotope can be calculated using the formula T1/2 = (ln 2) / λ, where λ is the decay constant. First, we need to find the decay constant using the given information.

The change in the decay rate over 5.00 days can be represented as (8253 - 3008) = 5245 decays.

Using the formula N = [tex]N0e^{(- \Lambda t)[/tex], where N is the number of remaining atoms, N0 is the initial number of atoms, and t is the time, we can find λ as ln(8253/3008) / 5.00 days = 0.2701 per day.

Substituting this value into the half-life formula gives T1/2 = (ln 2) / 0.2701 per day = 2.37 days.

Therefore, the half-life of the isotope is 2.37 days.

For more such questions on isotope, click on:

https://brainly.com/question/30548132

#SPJ11

The person has done 2327.5 joules of work to accomplish the task of climbing the stairs.

To find the work done by the person, we need to use the formula W = Fd, where W is the work done, F is the force applied, and d is the distance moved in the direction of the force. In this case, the force applied is the weight of the person, which can be calculated using the formula F = mg, where m is the mass of the person and g is the acceleration due to gravity (9.8 m/s^2).
So, the force applied is F = 95 kg x 9.8 m/s^2 = 931 N. The distance moved in the direction of the force is the height gained, which is 2.5 meters. Therefore, the work done by the person is W = Fd = 931 N x 2.5 m = 2327.5 joules.
The work done by the person to climb the stairs is 2327.5 joules. Work is defined as the energy transferred when a force is applied to an object and it moves in the direction of the force. In this case, the force applied is the weight of the person, which is a result of the gravitational attraction between the person and the Earth. As the person climbs the stairs, they do work against the force of gravity to lift their body to a higher elevation. This work is calculated by multiplying the force applied (weight) by the distance moved in the direction of the force (height gained). The unit of work is the joule, which is defined as the amount of work done when a force of one newton is applied over a distance of one meter. In this scenario, the person has done 2327.5 joules of work to accomplish the task of climbing the stairs.

To know more about Work Done visit:
https://brainly.com/question/31655489
#SPJ11

The direction of the acceleration of the elevator is upward.

To determine the magnitude and direction of the acceleration of the elevator, we need to use Newton's second law of motion, which states that force equals mass times acceleration (F=ma).

The tension in the rope, measured to be 88 N, is the force acting on the object. Since the object has a mass of 10 kg, we can use F=ma to calculate the acceleration of the elevator.

88 N = 10 kg x a

a = 8.8 m/s^2

So the magnitude of the acceleration of the elevator is 8.8 m/s^2.

To determine the direction of the acceleration, we need to consider the direction of the forces acting on the object. In this case, the force of gravity is acting downward on the object, while the tension in the rope is acting upward. Since the tension in the rope is greater than the force of gravity, the net force on the object is upward.

Learn more about acceleration here:-

https://brainly.com/question/12550364

#SPJ11

The correct statement is e. The proper length of a meter stick is always one meter, regardless of the reference frame or the observer's motion.

Proper length refers to the length of an object as measured in its own rest frame, i.e., the frame in which the object is not moving. In the rest frame of the meter stick, its proper length is always one meter. In other frames, such as those of observers who are moving relative to the meter stick, the length of the meter stick may appear shorter or longer due to the effects of length contraction. However, the proper length of the meter stick itself does not change.

In the theory of special relativity, , the concept of proper length is fundamental, as it allows for consistent measurements of distances between objects, even when those objects are moving relative to each other. The proper length of an object is the distance between two points on the object that are at rest relative to each other, as measured in the object's own rest frame. This length is invariant, meaning that it does not change as a result of the object's motion or the observer's motion.

In the case of a meter stick, the proper length is defined as the distance between two points on the stick that are at rest relative to each other. This length is always one meter, regardless of the observer's motion or the reference frame in which the measurement is made. However, the observed length of the meter stick will depend on the observer's motion and the relative velocity between the observer and the meter stick, due to the phenomenon of length contraction.

Length contraction is the effect by which a moving object appears shorter in length than it does when at rest. This effect arises from the time dilation and Lorentz contraction predicted by special relativity. These effects become significant when the relative velocity between the observer and the object approaches the speed of light.

In summary, the proper length of a meter stick is always one meter, as measured in the stick's own rest frame. However, the observed length of the meter stick will depend on the observer's motion and the relative velocity between the observer and the stick, due to the effects of length contraction.

learn more about special relativity here:

https://brainly.com/question/28289663

#SPJ11

The speed of conduction through a reflex arc is slower than the speed of conduction of an action potential along an axon because the reflex arc involves additional synaptic connections, which introduce delays in signal transmission.

The speed of conduction through a reflex arc is slower than the speed of conduction of an action potential along an axon due to additional synaptic connections involved in the reflex arc. In a reflex arc, the sensory neuron carries the signal from the sensory receptor to the spinal cord, where it synapses with an interneuron before reaching the motor neuron. This synaptic transmission introduces a delay as the chemical neurotransmitters need to cross the synaptic cleft. In contrast, in the conduction of an action potential along an axon, there are no synaptic connections involved, allowing for a faster propagation of the electrical signal along the length of the axon.

Learn more about reflex arc here:

https://brainly.com/question/894334

#SPJ11

In the scenario you described, it would be most difficult for the student to keep the meter stick from rotating when the masses are attached at the farthest point from the student's hand. This is because the torque (rotational force) acting on the meter stick increases with the distance of the mass from the axis of rotation (the student's hand).

The difficulty for the student to keep the meter stick from rotating depends on the distribution of the masses. If the masses are distributed evenly on both sides of the meter stick, it will be easier to balance and keep from rotating. However, if the masses are all on one side of the stick, it will be much more difficult to keep it from rotating. This is because the center of mass will be shifted to one side, causing an imbalance and rotational force. Therefore, the most difficult case for the student to keep the meter stick from rotating is when all the masses are on one side of the stick.

Learn more about meter here:-

https://brainly.com/question/4307551

#SPJ11

The final temperature of the soda-water mixture is approximately 34.9°C.

The task is to determine the final temperature of the soda-water mixture after all of the ice has melted. The solution is calculating the amount of heat received by the ice, the amount of heat lost by the soda, and the amount of heat required to melt the ice.

First, we must convert the soda and ice masses to kilogrammes:

mI = 0.18 kg mS = 12 oz / 35.273 oz/kg = 0.34 kilogramme

The amount of heat lost by the soda as it cools from its initial temperature of 13.5°C to the final temperature can then be calculated:

Qlost = 0.34 kg * 4186 J/(kg°C) * (13.5°C)

Qlost = 0.34 kg * 4186 J/(kg°C) * (13.5°C )

Similarly, we can calculate how much heat the ice gains when it warms from -15°C to 0°C and finally melts at 0°C:

Qgain = mI*cI*T + mI*Lf

T = (0°C - (-15°C)) = 15°C

Because the heat lost by the soda is equal to the heat gained by the ice, we can set Qlost = Qgain and solve for:

0.34 kg * 4186 J/kg°C * (13.5°C - F

= 0.18 kg * 2090 J/kg°C 15°C + 0.18 kg

= 334000 J/kg

When we simplify this equation, we get:

= 34.9°C = 15432 - 1423.88

= 10530 + 60012 49709

= 1423.88

For such more question on temperature:

https://brainly.com/question/26866637

#SPJ11

A) The object's heat capacity is 0.18 kJ/°C.

B) The specific heat of the item is 0.96 kJ/kgK.

A) The following formula may be used to calculate heat capacity:

  Heat Energy / Temperature Change = Heat Capacity

  Given: 2200 J of heat energy

         Change in temperature = 12 °C

  2200 J / 12 °C = 183.33 J/°C Heat Capacity

  Converting from degrees Celsius to kilojoules:

  Heat Capacity = 183.33 J/°C multiplied by (1 kJ/1000 J) = 0.18333 kJ/°C

  As a result, the object's heat capacity is roughly 0.18 kJ/°C.

B) The formula for specific heat is as follows: Specific Heat = Heat Capacity / Mass

  Weight = 190 g = 0.19 kilogramme

  Specific Heat = 0.947 kJ/kgK = 0.18 kJ/°C / 0.19 kg

  As a result, the specific heat of the item is roughly 0.96 kJ/kgK.

For more such questions on heat capacity , click on:

https://brainly.com/question/31963763

#SPJ11

We can use the formula for electric charge and current to calculate the current:

I = Q / t

where I is the current, Q is the charge, and t is the time.

In this problem, the charge Q is given as 0.22 μC, and the time t is given as 0.95 ms. However, we need to convert the charge to units of coulombs (C) before we can use the formula:

0.22 μC = 0.22 × 10^-6 C

Substituting the known values into the formula:

I = (0.22 × 10^-6 C) / (0.95 × 10^-3 s) = 0.23 A

Therefore, the current is 0.23 amperes (A).

To know more about refer electric charge here

brainly.com/question/9194793#

#SPJ11

To calculate the stress and strain on the wire, we can use the following formulas:

a) Stress (σ) = Force (F) / Area (A)

b) Strain (ε) = Change in length (ΔL) / Original length (L)

Given information:

Length of the wire (L) = 5 m

Diameter of the wire (d) = 2 mm = 0.002 m

Change in length (ΔL) = 0.25 mm = 0.00025 m

Force (F) = 50 N

First, let's calculate the cross-sectional area of the wire using the diameter:

Area (A) = π * (d/2)^2

A = π * (0.002/2)^2

A ≈ 3.142 * (0.001)^2

A ≈ 3.142 * 0.000001

A ≈ 0.000003142 m^2

Now, we can calculate the stress and strain:

a) Stress (σ) = F / A

σ = 50 / 0.000003142

σ ≈ 15,930,285.25 Pa

b) Strain (ε) = ΔL / L

ε = 0.00025 / 5

ε = 0.00005

So, the answers are:

a) Stress on the wire ≈ 15,930,285.25 Pa

b) Strain on the wire = 0.00005

Please note that the stress is in pascals (Pa) and the strain is a unitless quantity.

The coefficient of expansion of a steel is 0.000012 per C°. The coefficient of volume expansion (β) can be calculated by multiplying the linear expansion coefficient by three.

β is a measure of how much the volume of a material changes with temperature. It is related to the coefficient of linear expansion (α) by the equation β = 3α.

For the given type of steel, α = 0.000012 per C°. Therefore, β = 3α = 0.000036 per C°. This means that for every 1°C increase in temperature, the volume of this steel will increase by 0.000036 times its original volume.

It's worth noting that the coefficient of volume expansion may not be constant over a wide temperature range. In fact, for some materials, the coefficient may change significantly with temperature. Therefore, it's important to consider the temperature range of interest when selecting a material for a particular application, and to take into account any changes in volume that may occur due to temperature fluctuations.

To know more about the coefficient of expansion refer here :

https://brainly.com/question/14780533#

#SPJ11

Therefore, the thermal efficiency of the engine is 28.1%. This means that only 28.1% of the energy input to the engine is converted into useful work, while the remaining 71.9% is lost as waste heat.

The mechanical work output of the engine during one cycle can be found using the First Law of Thermodynamics, which states that the energy input to a system must equal the energy output plus any increase in internal energy. In this case, the energy input is 8900 J, and the energy output is 6400 J, so the mechanical work output can be found by

Mechanical work output = Energy input - Energy output
Mechanical work output = 8900 J - 6400 J
Mechanical work output = 2500 J
Therefore, the mechanical work output of the engine during one cycle is 2500 J.
The thermal efficiency of the engine can be found using the equation:
Thermal efficiency = (Mechanical work output / Energy input) x 100%
Plugging in the values we just calculated, we get:
Thermal efficiency = (2500 J / 8900 J) x 100%
Thermal efficiency = 28.1%
Therefore, the thermal efficiency of the engine is 28.1%. This means that only 28.1% of the energy input to the engine is converted into useful work, while the remaining 71.9% is lost as waste heat.

To know more about thermal efficiency visit:-

https://brainly.com/question/13677263

#SPJ11