Two ropes are identical. A wave traveling through the first rope has a frequency of 1. 5 hertz and a wavelength of 6 meters. What is the frequency of a wave in the second rope if its wavelength is 2 meters?(1 point)


3 hertz


9 hertz


4. 5 hertz


1. 5 hertz


(cmmt if u want to be added to a connection acadmy Physics B ig gc)

The upper plate must move with a force of 143 N in order to move at a speed of 1 m/s. The two fluids' contact has a fluid velocity of 0.714 m/s.

Pipe velocity is an area averaged attribute that is unaffected by the cross-sectional flow pattern or laminarity of the flow in the pipe. For instance, fluid may be moving twice as fast down the center axis as predicted by the pipe velocity.

Fluid Velocity

We are given fluid viscosities as;

₁ = 0.1 N.s/m²

₂ = 0.15 N.s/m²

Thicknesses of plates are;

h₁ = 0.5 mm and h₂ = 0.3 mm

Since the shear stress is constant throughout,

τ = ₁(du₁/dy₁) = ₂(du₂/dy₂)

⇒ ₁(Ui/h₁) = ₂(U - Ui)/h₂

where Ui is the interface speed and U is the upper body's movement speed, we have;

Ui = U/(1 + (₁/₂)*(h₂/h₁))

⇒ Ui = 1/(1 + (0.1/0.15)*(0.3/0.5))

⇒ Ui = 0.714 m/s

Force required is;

F = ₁ * (Ui/h₁) * (A)

We are given A = 1 m²

Thus;

F = 0.1 * (0.714/0.0005) * 1

F ≈ 143 N

To know more about Fluid Velocity visit:-

https://brainly.com/question/28965743

#SPJ4

Question:

Luids of viscosities 1  =0.1 N.s/ms and 2  =0.15 N.s/m2 are contained between two plates (each plate 1

m2 area). The thicknesses are h1=.5 mm and h2=0.3 mm, respectively. Find the force F to make the upper

plate move at a speed of 1 m/s. What is the fluid velocity at the interface between the two fluids?

Because a curved tube is not an homogeneous medium, we cannot perceive a light source through it. Hence the tube should have a straight, homogeneous medium so that the source of the light can be seen.

Light has always represented righteousness, kindness, wisdom, understanding, grace, hope, and the revelation of God in the Bible. On the other side, darkness has been associated with sin, evil, and hopelessness.

Aspects of the divine presence that are felt as light in theophany or visions, or that are depicted as such in allegorical or metaphor, are referred to as divine light in theology.

To know more about light visit:

https://brainly.com/question/15200315

#SPJ1

However, in general, the law of conservation of momentum states that the total momentum of an isolated system remains constant if there are no external forces acting on the system. This means that the sum of the momenta before an event is equal to the sum of the momenta after the event.

What is the momentum ?

Momentum is the quantity of motion of a moving body, also known as its mass multiplied by its velocity. Momentum is a vector quantity, which means it has both a direction and a magnitude. Momentum is conserved in an isolated system. This means that the total momentum of a system remains constant as long as no external forces act on it. Momentum is an important concept in classical mechanics, as well as in modern physics. In everyday life, momentum can be seen in sports, such as a baseball thrown with a certain speed, or a car moving with a certain speed.

If the red and blue carts are part of an isolated system, their total momentum before the event would be equal to their total momentum after the event. Therefore, any change in the momentum of one cart must be compensated for by an equal and opposite change in the momentum of the other cart.

So, if one cart experiences an increase in momentum after the event, the other cart must experience a decrease in momentum of the same magnitude. Conversely, if one cart experiences a decrease in momentum, the other cart must experience an increase in momentum of the same magnitude.

To learn more about momentum

brainly.com/question/402617

#SPJ4

[tex]T_{1}+\sqrt{2 }T_{1}[/tex]  is the time (in terms of [tex]T_{1}[/tex]) does it take the ladybug to get back to its starting point from the place where it reverses its acceleration

The following is a roughly formula-free, Physics-focused solution. The velocity continues to move incorrectly even when the acceleration  [tex]T_{1}[/tex]changes. By symmetry, the ladybug is at rest after an additional period  and is twice as far from its starting point as it was before it applied the brakes.

As a result, it must now go twice as far. Under constant acceleration, the distance traveled is proportional to the square of the time. Consequently, the amount of time needed to return to the starting location from the farthest point reached is 2–[tex]\sqrt{T_{1} }[/tex]. Total time from the time the acceleration reversed is therefore [tex]T_{1}+\sqrt{2 }T_{1}[/tex].

Learn more about acceleration

brainly.com/question/12550364

#SPJ4

The velocity and position of a box being pushed across the floor by a constant force with a coefficient of kinetic friction are determined by Newton's second law of motion, which states that the force acting on an object is equal to its mass times its acceleration.

In this scenario, the applied force, friction force, and mass of the box all play a role in determining its velocity and position.

As the box is pushed, it will eventually reach a velocity at which the frictional force is equal in magnitude to the applied force, and the net force on the box will be zero. At this point, the box will move at a constant velocity, as it is no longer accelerating. The position of the box will be dependent on the initial velocity, the applied force, and the time elapsed.

Overall, the velocity and position of a box being pushed across the floor by a constant force with a coefficient of kinetic friction are interrelated and determined by the balance of forces acting on the object.

Learn more about Newton's Laws of motion here:

https://brainly.com/question/14222453

The complete question is:

What is the relationship between the velocity and position of a box being pushed across the floor by a constant force with a coefficient of kinetic friction?

#SPJ4

The difference in point of view that occurs when the lens (or other device) through which the eye views a scene is separate from the lens that exposes the film is called the parallax effect.

Parallax effect is an interactive technique used by web developers to create a visually engaging experience for users. It works by having the background move at a slower speed than the foreground when the user scrolls down the page. This creates an illusion of depth, as if the user is looking into the scene from different angles. The effect is especially popular for creating immersive experiences such as 3D games, virtual tours, and interactive storytelling. Parallax effect can be used to bring websites to life, offering users an engaging and dynamic experience. It is also a great tool for storytelling, helping to convey emotion and create a unique visual experience.

To learn more about parallax effect
https://brainly.com/question/17164388
#SPJ1

The one and only way to ensure that power off in a system, circuit, or piece of equipment is to measure the voltage with a known working meter.

To learn more about electric circuit refer to :

https://brainly.com/question/2969220

#SPJ1

The new resistance of the copper after doubling the length and reducing the radius will be 8 times of the original resistance.

Resistance can be defined as the property of the conductor which opposes the flow of electric current. Resistance is also defined as the ratio of the voltage applied to the electric current flowing through the circuit.

R = ρl/ A

where, R is the electric circuit,

ρ is the resistivity or specific resistance,

l is the length of the wire,

A is the cross-sectional area of the wire.

If we double the length of copper wire and reduce the radius to half. Then, the new resistance will be:

R = ρl/ A

l' = 2l

r' = r/2

A = πr²

A' = π(r/2)²

A' = πr²/4

R' = new resistance,

R' = ρ ×2l/ πr²/4

R' = 4 × ρ ×2l/ πr²

R' = 8ρl/ A

Therefore, the new resistance will be 8 times of the original resistance.

Learn more about Resistance here:

https://brainly.com/question/29427458

#SPJ1

F=-mg sin is the net force operating on a basic pendulum bob of mass m. It is a force that restores.

A simple pendulum's restoring force is directed towards the mean position when it moves in a simple harmonic motion (lowest point). Here, the force of gravity acts as the restoring force at the centre of mass of the bob.

Pendulums are employed to control clock movement because the period—the amount of time between each full oscillation—is constant. The formula for a pendulum's period T is T = 2L/g squared.

To know more about mass visit:-

https://brainly.com/question/30337818

#SPJ4

The required new magnification of the telescope when the focal lengths of objective lens and eye-piece are given is calculated to be four times that of original magnification.

We know the expression for magnification as, m = -fo/fe

where,

The objective lens's focal length is fo

fe is the focal length of eye piece

It is given that, focal length of the objective lens is doubled.

⇒ fo₂ = 2 fo

It is given that, focal length of the eye piece is doubled.

⇒ fe₂ = 1/2 fe

So, the new magnification is,

m' = -fo₂/fe₂ = - 2 fo/(1/2 fe) = -4 fo/fe = 4 m

Thus, the required new magnification is calculated to be four times that of the original magnification.

To know more about magnification:

https://brainly.com/question/4596751

#SPJ4

To burn a hole in a piece of paper with sunlight using your father's 1.80 D reading glasses, you must hold the glasses about 6 cm away from the paper.

This is because the glasses will act as a magnifying lens, and the focal length of the lens is determined by the diopter number (1.80 in this case). The focal length of a 1.80 D lens is approximately 6 cm.

The focal length of a lens is the distance between the lens and the image sensor when the subject is in focus, usually stated in millimeters (e.g., 28 mm, 50 mm). The focal length determines the angle of view of the lens, and thus how much of the scene will be captured when the image is taken.

Learn more about The focal length:

https://brainly.com/question/28039799

#SPJ4

Clap-echo technique With this technique, you time how long it takes you to hear an echo after a loud clap. You clap loudly when far away from a wall, then wait for the echo.

speed equals distance/time. A sound wave will cover a greater distance in the same amount of time as it moves quicker. The speed of a sound wave would be 350 m/s if it were noticed to cover 700 meters in 2 seconds.

The distance traveled is twice as far as the gap between you and the wall (because the sound has to travel to the wall and back).

To learn more about distance here:

https://brainly.com/question/11567236

#SPJ1

a) Rocks reach height 26.4 times maximum height they could reach on Earth b) rocks will be 0.753 times duration they would be in the air on Earth

(a) Max height H reached by a projectile launched vertically upward on Earth is given by:

[tex]H = v^{2} / (2g),[/tex]

where v₀ : initial velocity and g: acceleration due to gravity on Earth. To find height reached by same projectile launched with same initial velocity on Mars, we can use same formula but with the value of g on Mars:

[tex]H = v^{2} / (2g),[/tex]

where gₘ is the acceleration due to gravity on Mars. We know that  initial velocity of the rocks is the same on both planets, so we can write:

[tex]H = H * g / g[/tex]

Put values:

[tex]H = H * 9.81 m/s^{2} / 3.71 m/s^{2} = 26.4 * H[/tex]

Therefore, the rocks ejected from the volcano on Mars would reach a height that is 26.4 times the maximum height they could reach on Earth.

(b) The time T for the rocks to be in the air on Earth can be found using the formula:

[tex]T = 2v / g[/tex].

To find time the rocks would be in air on Mars, we use same formula but with the value of g in terms of Mars:

[tex]T = 2v / g[/tex]

Put values:

[tex]T = 2v / 3.71 m/s^{2} = 2/ (9.81 m/s^{2} / 3.71 m/s^{2} ) * (2v / 9.81 m/s^{2} )[/tex]

[tex]Tm = (2/2.652)*T[/tex]

[tex]Tm = 0.753 * T[/tex]

Learn more about height here:

https://brainly.com/question/30530692

#SPJ4

The rate of diffusion is directly related to concentration, temperature, and pressure meaning that an increase in concentration, temperature, or pressure results in an increase in the rate of diffusion.

This is because diffusion is a process where particles move from an area of high concentration to an area of low concentration, driven by a concentration gradient. As the concentration gradient increases, more particles move from the high concentration area to the low concentration area, resulting in a faster rate of diffusion.

Temperature also affects the rate of diffusion because it affects the kinetic energy of the particles. At higher temperatures, particles have more kinetic energy and move faster, leading to a higher rate of diffusion.

Pressure affects the rate of diffusion because it affects the concentration gradient. An increase in pressure can compress the gas and increase the concentration gradient, resulting in a higher rate of diffusion.

To know more about the diffusion, here

brainly.com/question/14392880

#SPJ4

The voltage across the resistor and capacitor will be the same. This is because the voltage source is supplying the same voltage to both components, and since the same amount of current is passing .

Voltage is a measure of electrical potential energy per unit charge. It is measured in volts (V). Voltage is an important factor in the functioning of electric circuits. It determines the amount of current that will flow in a circuit. A higher voltage will cause more current to flow through the circuit, while a lower voltage will cause less current to flow. Voltage is also related to power, as the electrical power is equal to the product of the voltage and current. the same amount of current is passing through both components, the voltage drop across each component must be equal.

To learn more about voltage

https://brainly.com/question/1176850

#SPJ4

It was discovered that the rate of desorption of a single molecular layer of n-butane from a single crystal of aluminum oxide was first order. constant of 0. 128/s at 150 K , Half life=[tex]\frac {ln(2)}{k}[/tex]=5.415 s

For first order desorption:

In([tex]\frac {N}{N_o}[/tex]) =-kt and [tex]\frac {N}{N_o}[/tex] = [tex]e^{(-kt)[/tex] where N is the number of molecules remaining at time t, No is initial number and k is rate constant

(A) Half life=[tex]\frac {ln(2)}{k}[/tex]=5.415 s

(B) 25% desorbs [tex]\rightarrow[/tex]  75% remains

⇒ [tex]\frac {N}{N_o}[/tex] x 100% = 75% => [tex]\frac {N}{N_o}[/tex]=0.75

In(0.75)=-0.128 x t

Time t = 2.25 s

(C) 50% desorbs ⇒ 50% remains

=> [tex]\frac {N}{N_o}[/tex] x 100% = 50% => [tex]\frac {N}{N_o}[/tex]= 0.50

In(0.50) = -0.128 x t

Time t = 5.42 S

(D) For t = 14 s

Fraction remaining= [tex]\frac {N}{N_o}[/tex] =[tex]e^{(-0.128 \times 14)[/tex]

Fraction remaining= -0.167 (approximately 0.17)

(E) For t = 20 s

Fraction remaining= [tex]\frac {N}{N_o}[/tex] = [tex]e^{(-0.128 \times 20)[/tex]

Fraction remaining=  -0.0773 (approximately 0.077)

Learn more about Half life

brainly.com/question/24710827

#SPJ4

Northern American Emergency Response Guide.The main goal of the ERG Handbook is to help first responders immediately identify any unique or general risks associated with the material(s) at issue.

There is also Guide 111, which is for "hazardous" materials.When using generic information, make sure to replace it with more detailed instructions as soon as new information becomes available.

The orange panel next to the diamond-shaped sign or on the extremities and sides of the a cargo tank, vehicle, or rail car may also display the 4-digit ID Number.

To know more about Emergency Response Guide visit:

https://brainly.com/question/14949646

#SPJ4

The gauge pressure at point P, which has a zero-reference against the atmospheric pressure, is 3200 Pa. The needle meets the wider chamber of the syringe at the end of the needle.

Using Poiseuille's law, we can resolve the exercise. In a closed pipe, it states that for a fluid in laminar flow.

The equation:

ΔP = 8μLQ / 4r⁴

Where,

μ = viscosity of the fluid

L = length of the pipe

r = radius

Q = Av

= πr²v

= (3.14 x 10⁻³) (10)

= (3.14 x 10⁻⁵)

Hence, the gauge pressure:

ΔP = 8 (0.001) (4 cm) (3.14 x 10⁻⁵)) / 4 (0.001 m)⁴

= 3200 Pa

So, the gauge pressure of the water at point P is 3200 Pa.

And, the needle meets the wider chamber of the syringe at the end of the needle.

Learn more about  Poiseuille's law here: https://brainly.com/question/14830017

#SPJ4

In an isothermal expansion, the pressure of a monatomic ideal gas increases by a factor of 1/3 (or 2/3).

A collection of presumptions about a gas's behavior defines, it as an ideal gas in theory. These hypotheses, which are based on experimental observations of actual gases, are helpful for comprehending and forecasting the behavior of gases under diverse circumstances.

The temperature of the gas doesn't change during an isothermal expansion. In the equation of state for an ideal gas, PV = nRT, where n is the number of moles, R is the universal gas constant, and T is the temperature, pressure and volume are connected.

The pressure of a monatomic ideal gas will change by a factor of 1/3(2/3) if its volume triples. This can be obtained by maintaining a constant temperature and changing the equation of state to P = (nRT) / V.

Since the pressure and volume are inversely related, the pressure will fall by a factor of 1/3 (or 2/3) if the volume triples.

To know more about ideal gas, visit:

https://brainly.com/question/29202954

#SPJ4

The velocity of the ball just before it hits the ground is 35 m/s.

What is velocity?

Velocity is a vector quantity that describes the rate of change of an object's position in a specific direction. It is defined as the derivative of an object's position with respect to time. Mathematically, velocity is expressed as:

v = Δx / Δt

The velocity of the ball just before it hits the ground can be calculated using the concept of projectile motion. In this case, we have two components of motion: horizontal and vertical. The horizontal component is constant and equal to the initial velocity, while the vertical component is affected by gravity and follows a parabolic path.

We can use the following equation to find the time it takes for the ball to fall from the roof to the ground:

h = vi * t + 0.5 * g * t²

where h is the height of the building (45 m), vi is the initial velocity (which we are trying to find), g is the acceleration due to gravity (9.8 m/s²), and t is the time it takes for the ball to fall.

Since the ball lands 105 m from the base of the building, we can also use the horizontal component of the motion to find the time:

d = vi * t

where d is the horizontal distance traveled by the ball (105 m).

We can equate these two equations to eliminate time and find the velocity of the ball:

h = vi * (d/vi) + 0.5 * g * (d/vi)²

45 = 105 + 0.5 * 9.8 * (d/vi)²

(d/vi)² = 2 * h / g = 2 * 45 / 9.8 = 9.18

d/vi = 3

vi = d / 3 = 105 / 3 = 35 m/s

So, the velocity of the ball just before it hits the ground is 35 m/s.

To learn more about velocity:

https://brainly.com/question/25749514

#SPJ4

If the car is initially moving at a speed of 45 mi/h and it takes 300 ft to stop with uniform acceleration after its brakes are applied, it will take 600 ft to stop under the same conditions.

This is because the deceleration is the same, but the initial velocity is halved.

Acceleration is the rate of change of velocity of an object with respect to time. It is a vector quantity which is defined as the rate of change of an object's velocity and is usually represented by the symbol a. Acceleration can be caused by a variety of factors, including external forces, changes in direction, or changes in speed. In physics, acceleration can be described as the rate of change of an object's velocity over a period of time.

Learn more about initial velocity:

https://brainly.com/question/28736305

#SPJ4

All of the above given statements are true.

A membrane controls the flow of chemicals between two environments as a selectively permeable barrier. The cell membrane is the most well-known biological membrane.

a. The amount of membrane fluidity varies based on the membrane's make-up. This is because the fluidity of the membrane can be impacted by the lipid composition, particularly the length of fatty acid chains and degree of unsaturation of phospholipids.

b. Phospholipids can travel around the membrane's lateral space quite freely. This is so that individual phospholipids can migrate laterally inside the membrane's lipid bilayer structure.

c. Unanchored proteins can essentially travel wherever they choose in the membrane's lateral space. This is due to the ability of proteins to diffuse laterally within the lipid bilayer, independent of the cytoskeleton or other proteins in the membrane.

These conclusions accurately characterize the degree of fluidity within the membrane and how the ratio of lipids to proteins affects it.

To know more about cell membrane, visit:

https://brainly.com/question/16589545

#SPJ4

Answer:

Look below

Explanation:

The possible genotypes of the offspring are: TT, Tt, and tt.

The possible phenotypes of the offspring are: tall and short.

The percentage chance of being homozygous can be calculated using a Punnett square. When the heterozygous parents are crossed, the possible genotypes of the offspring are:

| T | t

--|---|---

T | TT| Tt

t | Tt| tt

From the Punnett square, we can see that there is a 25% chance of the offspring being homozygous (TT or tt). This is because there are four possible outcomes and two of them result in a homozygous genotype (TT and tt).

The required hydrostatic force on the dam when width and the radius of the dam are given is calculated to be 31284956.29 N.

It is given that width of the dam is 70 m.

Radius of the circle is 7 m.

The height of the dam will be equal to the half of its radius.

h = r/2 = 7/2 = 3.5 m

Area is given by the formula, A = r ω

where,

ω is width

r is radius

Volume is given as, V = ω πr²/4

Horizontal force is given by, Fx = ρ g h A = 1000× 9.8× 7/2× 7× 70 = 16807000 N

Vertical force Fy =  ρ g V = 1000 × 9.8 × 70 × π 7²/4 = 98× 7000× 49π /4 = 26386990 N

The resultant of vertical and horizontal force is nothing but the hydrostatic force.

F = √(Fx² + Fy²) = √(16807000² + 26386990²) = √(282475249000000+696273241260100) = 31284956.29 N

Thus, the hydrostatic force on the dam in N is calculated to be 31284956.29 N.

To know more about hydrostatic force:

https://brainly.com/question/21800451

#SPJ4

The car travels 90m before it comes to rest.

Distance is the total movement of an object without any regard to direction. We can define distance as how much ground an object has covered despite its starting or ending point.

Velocity (v) is a vector quantity that measures displacement (or change in position, over the change in time.

Acceleration is defined as the rate of change of velocity with respect to time.

The initial velocity is 30.0 m/s.

The acceleration is [tex]-5.0\ m/s^2[/tex].

The car comes to a stop. Hence the final velocity is 0 m/s.

Using the third equation of motion,

[tex]v^2 - u^2=2as[/tex]

Substituting the values,

[tex]0^2 - 30^2=2(-5)s[/tex]

The value of s is 90m.

To know more about the acceleration, here

brainly.com/question/13860566

#SPJ4

The pressure that a gas, at a constant temperature, exerts over a liquid surface is known as vapour pressure. Since the kinetic energy of molecules increases with temperature, vapour pressure likewise rises.

As a result, more molecules possess the necessary energy to transform from a liquid to a gas.

The pressure that a gas, at a constant temperature, exerts over a liquid surface is known as vapour pressure. Due to the fact that more molecules have adequate kinetic energy to transition from a liquid to a gas as the temperature rises, the vapour pressure likewise rises.

A liquid or solid's vapour pressure increases along with its temperature. On the other hand, when the temperature drops, the vapour pressure drops.

There are several techniques to calculate a liquid's vapour pressure. A little amount of the liquid is injected into a closed flask that is attached to a manometer for a straightforward measurement.

Learn more about Vapour pressure here:

https://brainly.com/question/2693029

#SPJ4

When making a lane change in front of a car, the car should be toward the middle of your rearview mirror. Correct option is D.

Place the seat and steering wheel so that you can access the gear shifter, brake pedal, and accelerator while still feeling comfortable. Move the rearview mirror gently so that you can look straight out of the back windshield's centre without turning your head.

A straight, even reflection of the back window should be visible in the rearview mirror. Every 5 to 8 seconds, check your rearview mirror. You can keep track of who is approaching you, who has already past you, and who is acting erratically or dangerously close behind you by often checking your rearview mirror.

An adjustable reflecting device called a rearview mirror allows drivers to see the road, other cars, and things behind their vehicle.

To know more about mirrors:

https://brainly.com/question/13120439

#SPJ4

The spheres are now 6.08 cm apart. The force between two charged spheres is proportional to the product of their charges and inversely proportional to the square of the distance between them.

This means that if the force is tripled, the distance between the spheres must have been reduced by a factor of the square root of 3. To find the new distance, we can use the formula:

d_new = d_old / √3

Where d_old is the original distance of 10.68 cm and d_new is the new distance. Plugging in the values, we get:

d_new = 10.68 cm / √3 = 6.08 cm

So, the spheres are now 6.08 cm apart.

In this case, F_old / F_new = 1/3, since the force has been tripled. Plugging in the original distance of 10.68 cm and the value for F_old / F_new, we can calculate the new distance. The final result shows that the spheres are now 6.08 cm apart.

This result shows how the force between charged spheres is directly influenced by the distance between them. Understanding this relationship is important in many fields, including physics, electrical engineering, and materials science.

Learn more about charge here:

https://brainly.com/question/20342415

#SPJ4