the ultimate tensile strength of a material is the maximum amount of tensile stress that it can take before failure, and is measured by dividing the applied load by the

Answers

Answer 1

The highest stress that a material can sustain while being stretched or pulled before breaking is known as the Ultimate Tensile Strength (UTS), also abbreviated to tensile strength (TS). When a material is brittle, it fractures shortly after the yield point has been achieved.

What is the tensile strength of a material?

With ductile materials, the yield strength is seen concurrently, and ultimate strength is attained when the material keeps stretching until it reaches the breakpoint.

From this curve, we can infer that the ultimate tensile strength (U.T.S. ), max = Pmax /A0. Where Pmax is the greatest load and A0 is the initial cross-sectional area, is the load at failure divided by the original cross-sectional area.

Therefore, The ultimate tensile strength of a material is the maximum amount of tensile stress that it can take before failure, and is measured by dividing the applied load by the original cross-sectional area.

Learn more about tensile strength here:

https://brainly.com/question/14293634

#SPJ4


Related Questions

From what height would a car have to fall in order for the magnitude of its momentum to equal the magnitude of its momentum when it is moving on a highway at 34 m/s? Express your answer with the appropriate units. μA ? Ay = Value Units Submit Request Answer

Answers

From the height of 58.91 m would a car have to fall in order for the magnitude of its momentum to equal the magnitude of its momentum when it is moving on a highway at 34 m/s.

What is momentum?

A motion of an item is said to have momentum when its mass multiplied by its speed. If you describe anything as having momentum, you are describing its mass and direction of motion. A truck loaded with products has a big mass and must slow down before a stop signal since stopping is exceedingly difficult due to the truck's enormous momentum and constant speed. Even though a bullet has a relatively little mass and a very high velocity, it nevertheless possesses a significant amount of momentum.

Magnitude of momentum of car on highway = m × 34 kg.m/sec

Here, mass remains the constant, speed of the car should be = 34

Thus, v² = v₀² = 2gd

v₀ = 0

v = 34 m/sec

so, d = v² /2g

d = (34)² / 2 × 9.81

d = 58.91 m

From the height of 58.91 m would a car have to fall in order for the magnitude of its momentum to equal the magnitude of its momentum when it is moving on a highway at 34 m/s.

To know more about momentum refer to:

https://brainly.com/question/1042017

#SPJ1

It can be difficult, especially for someone with partial hearing loss, to understand someone speaking rapidly in a low, soft voice.
Which of the following auditory characteristics are associated with sound waves for low, quiet voices?
correct:
-low frequency
-low amplitude
incorrect
- vestibular

Answers

Correct, low, quiet voices have sound waves with low frequency and low amplitude. Instead of hearing, the vestibular system controls balance and spatial orientation.

By comparing the two ears' responses, what aspects of the sound can be used to identify its origin?

In order to determine where a sound is coming from, humans rely on two key clues. These signals include (1) the ear the sound strikes first (interaural temporal differences) and (2) the volume of the sound when it reaches each ear (known as interaural intensity differences).

What procedures are necessary for the brain to interpret sound waves as sound?

Sound waves enter the outer ear and travel to the eardrum via the auditory canal. The three tiny ossicles carry the ensuing vibrations into the cochlea, where hair cells are able to pick them up.

to know more about the auditory canal here:

brainly.com/question/2222049

#SPJ1

A worker wants to load some bricks in to his van. there are 1000 bricks and when stacked neatly they measure 2m by 1m by 1m. If the vans maximum load is 1000kg, how many bricks can he load?

Answers

The worker can load {500/ρ} number of bricks into the van.

What is mass?

Mass is the total amount of matter present inside a body.

Given is that a worker wants to load some bricks in to his van. There are 1000 bricks and when stacked neatly they measure 2m by 1m by 1m.

Assume the density of the brick to be {ρ}. Let's assume that he can load {n} bricks inside the van. So, we can write -

n x mass of 1 brick = maximum load

n x ρ x V = L{max}

nρV = L{max}

n = L{max}/ρV

n = 1000/(2 x 1 x 1 x ρ)

n = 500/ρ

Therefore, the worker can load {500/ρ} number of bricks into the van.

To solve more questions on mass & weight, visit the link below -

https://brainly.com/question/28704035

#SPJ9

Which motion might be represented by this position-versus-time graph? Х t t 0 - 0 O A car drives toward the left at first slowly, then faster. O A car drives toward the left at first quickly, then slower. O A car drives toward the right at first slowly, then faster. O A car drives toward the right at first quickly, then slower. O A ball rolls down a ramp that is at first not too steep, then steeper. O An elevator descends at first slowly, then faster.

Answers

The motion that could be represented by the given position-versus-time graph is "A car drives toward the right at first slowly, then faster."

We can see that the graph has a positive slope, which indicates a motion in the positive direction. The fact that the slope is increasing over time means that the object is accelerating, which is consistent with the car starting off slowly and then getting faster.

phase 1 : object moves towards its mean position, velocity must be slow.

phase 2 : object moved to its initial position taking much less time compared to phase 1 but in the same direction to reach its mean position.

Therefore, the correct option is "A car drives toward the right at first slowly, then faster."

Read more about Position-Versus-Time Graph:

https://brainly.com/question/28918837

#SPJ4

8. (a) The mass m of an object is proportional to its volume V: m = kV. What are the SI units of k? (b) If the distance d an object moves in time t is given by the equation d = At-, find the SI units of A. (c) If the speed v of an object depends on time t according to the equation v = A + Bt + Ct4, what are the SI units of A, B, and C?

Answers

density is the mass of a specific material per unit volume. d = M/V, in which d is densities, M is mass, as well as V is volume, is the formula for density. Common units for expressing density are grams per cubic inch.

What is the mass unit?

 There are several ways to measure mass, including kilograms, grams, pounds, and pounds, but the SI unit de mass is the "kilogram" or kg. Using the right conversion formula, any unit of weight can be changed into another unit without changing the significance or meaning of the quantity being measured.

Describe mass.

Definition, Units, Formula, and Examples of Mass The quantity of matter that makes up every object or body is the greatest way to understand mass. Everything that we can see has mass. Examples of objects with mass include a table, an chair, your mattress, a ball, a tumbler, and even air. The mass of a thing determines whether it is light or heavy.

To know more about mass visit:

https://brainly.com/question/671503

#SPJ4

The purpose of using epicycles and deferents to explain the motion of the planets in the night sky was to account for a. prograde motion b. Mercury and Venus' limited angular distance from the Sun. c. retrograde motion d. non-uniform speed of the planets in their orbits. e. precession of the equinoxes.

Answers

Epicycles and deferents were used to account for the planets' irregular orbital speeds in order to explain how they moved in the night sky.

What is meant by an epicycle?

A planet moves in a circle that has a core that is also rotated simultaneously on the rim of a wider circle, according to an early theory of astronomy.

Ptolemy was forced to develop a model of planetary motion that utilised epicycles in order to maintain the geocentric cosmology of the time and account for Mars' retrograde motion. An epicycle is essentially a small "wheel" that revolves around a larger wheel.

To know more about astronomy visit:

https://brainly.com/question/5165144

#SPJ4

An idealized object that does not reflect or scatter any radiation that hits it, but simply absorbs every bit of radiation that falls on it is called:

Answers

A blackbody is a hypothetical object that absorbs all incident radiation without reflecting or scattering any of it.

What exactly is a blackbody?

A blackbody is a hypothetical object that emits all wavelengths of radiation while simultaneously absorbs all electromagnetic waves that strike it.

Another name for it is a perfect emitter or absorber.

Blackbody radiation is the specific spectral distribution of radiation produced by a blackbody that is only temperature dependant.

Understanding the behaviour of thermal radiation and the properties of stars, galaxies, as well as other celestial objects in physics and astronomy is dependent on this concept.

Planck's law, which gives the spectral density of a radiation emitted by the a blackbody at a temperature t as a function of the wavelength of the radiation, describes the radiation released by a blackbody as being solely dependent on its temperature.

To know more about radiation visit:

brainly.com/question/24469662

#SPJ1

Compare dispersing light into colors with a prism and then into a grating. The 30-60-90 prism is made of glass with indices n {red}=1.52 and n {blue}=1.53. The grating has 500 slits per millimeter. a. What is the angular separation between red and blue light leaving the prism in degrees? b. What is the angular separation between red (650 nm) and blue (450 nm) light leaving the grating in degrees? Explain

Answers

Both a prism and a diffraction grating can be used to disperse white light into its component colors, which are a range of wavelengths of visible light.

What is diffraction?Due to the differing refractive indices of the prism material for various wavelengths of light, a prism operates by refracting the various hues of light as they pass through at slightly different angles. This causes the colours to disperse into a spectrum that resembles a rainbow. The prism equation provides the angle of departure for the various hues.

θ = sin^(-1) (-1)

[n avg] = [(n blue - n red) sin()]

where n red and n blue are the prism's respective refractive indices for red and blue light, and n avg is the average of the two refractive indices, and is the angle of deviation, is the angle of incidence of the light on the prism, and so forth.

Assuming an angle and the values given as n red = 1.52, n blue = 1.53, and n avg = (n red + n blue)/2 = 1.525

of incidence of 45 degrees, we can calculate the angle of deviation to be:

θ = sin^(-1)[(1.53 - 1.52) sin(45°) / 1.525] = 0.34°

Therefore, the angular separation between red and blue light leaving the prism is 0.34 degrees.

A diffraction grating works by diffracting light through a series of closely spaced parallel slits or lines, which act like a series of tiny prisms that diffract the light at different angles depending on its wavelength. The angle of diffraction of a particular color is given by the grating equation:

nλ = d(sin θ_i + sin θ_d)

where n is the order of the diffraction (usually n=1), λ is the wavelength of the light, d is the spacing between the grating lines, θ_i is the angle of incidence of the light on the grating, and θ_d is the angle of diffraction.

Using the given values of d=500 nm (i.e., 500 slits per mm), λ_red = 650 nm and λ_blue = 450 nm, and assuming an angle of incidence of 0 degrees (i.e., the light is perpendicular to the grating), we can calculate the angles of diffraction for red and blue light to be:

θ_red = sin^(-1)[(nλ_red / d) - sin(θ_i)] = sin^(-1)[(1650 nm / 500 nm) - sin(0°)] = 0.837°

θ_blue = sin^(-1)[(nλ_blue / d) - sin(θ_i)] = sin^(-1)[(1450 nm / 500 nm) - sin(0°)] = 0.579°

Therefore, the angular separation between red and blue light leaving the grating is:

θ_separation = θ_red - θ_blue = 0.837° - 0.579° = 0.258°

This is smaller than the angular separation obtained from the prism, and is due to the fact that a grating has a higher dispersion than a prism, meaning that it can separate colors more effectively. However, a grating also has narrower angular acceptance and higher order diffraction peaks that can interfere with the desired signal.

To know more about diffraction , check out :

https://brainly.com/question/16749356

#SPJ4

Water is poured into a container that has a small leak. The mass m of the water is given as a function of time t by m=5.00 t 0.8
−3.00t+20.00, with t≥0,m in grams, and t in seconds.
At what time is the water mass greatest.

Answers

Answer:

Explanation:

when gravity pulls the water molecules downwards, they will fall. But if they're in a container, the container will keep them from spreading out completely. This is what's called 'taking the shape of the container'

drops his phone of mass 650 g from his hand at a height
of 1.50 m above the ground. As the phone is dropped, gravity
does 8.80 J of work.
What is the speed of the phone just before touching the ground?

Answers

The speed of the phone just before touching the ground is approximately 3.92 m/s.

What is  conservation of energy?

We can use the conservation of energy to find the speed of the phone just before touching the ground. Initially, the phone has potential energy due to its height above the ground, which is converted into kinetic energy just before the phone touches the ground.

The potential energy of the phone just before it is dropped is:

[tex]PE = mgh[/tex]

where m is the mass of the phone, g is the acceleration due to gravity (9.81 m/s^2), and h is the height of the phone above the ground (1.50 m). Thus, the initial potential energy of the phone is:

[tex]PE = (0.65 kg)(9.81 m/s^2)(1.50 m) = 9.57 J[/tex]

As the phone is dropped, gravity does 8.80 J of work on the phone. This work is converted into kinetic energy just before the phone touches the ground. Thus, the final kinetic energy of the phone just before it touches the ground is:

[tex]KE = W = 8.80 J[/tex]

The kinetic energy of an object is given by:

[tex]KE = (1/2)mv^2[/tex]

where v is the speed of the object.

Thus, we can solve for the speed of the phone just before it touches the ground:

[tex]v = sqrt(2KE/m) = sqrt(2(8.80 J)/(0.65 kg)) = 3.92 m/s[/tex]

Therefore, the speed of the phone just before touching the ground is approximately 3.92 m/s.

Learn more about conservation of energy, here:

https://brainly.com/question/13949051

#SPJ9

let a be the sum of the last three digits and let b be the last digit of your 8-digit student id. example: for 20245347, a

Answers

Answer: The given time period of oscillation would be around 0.9515 seconds.

Explanation:

The very first 54.0 km were driven at an average speed, while the final 86.0 km were driven at in a speed of (43.0 b) km/h. She travels at an average speed of 43.75 km/h for the entire journey.

How speed is it?

Velocity is the pace and velocity of an object's movement, whereas speed is the forecasting at which an objects is travelling along a path. In other words, velocity is a vector, whereas quickness is a scalar value. As a result, the fundamental unit of time and the basic element of distance are combined to form the Special name of speed. Thus, the metre per second (m/s) is the Substrate concentration of speed.

a = 19 and b = 7

Average speed, 54 km = 48+a km/h

Plug a = 19

54 km = 48+19

= 67 km/h

remaining speed

86 km = 43-b km/h

where b = 7

Average speed = 36 km/h

Average speed = total distance / total time taken

speed = distance/time

time = distance/speed

To cover 54 km = 54/67 hr

To cover 86 km = 86/36 hr

Total time = 3.2 hours.

Total distance = 86+54

= 140 km

Average speed 140/3.2

= 43.75 km/ h

To know more about speed visit:

https://brainly.com/question/28224010

#SPJ4

When tuning a piano, a technician strikes a tuning fork for the A above middle C and sets up a wave motion that can be approximated by y = 0.001 sin 880πt, where t is the time (in seconds).(a) What is the period of the function?(b) The frequency f is given by f=1p. What is the frequency of the note?

Answers

The required period of the function is calculated to be 1/440 sec and frequency is calculated to be 440 hertz.

The equation of the sinusoidal wave is given as, y = 0.001 sin 880πt

Comparing the given equation with that of the general equation of the wave in simple harmonic motion, we have, y = a sin ωt

where,

y is displacement

a is amplitude

t is time

ω is angular frequency

So, Angular frequency ω = 880π

The period of the function is given by the formula, p = 2π/ω = 2π/880π = 1/440 sec

We know the equation for frequency as, f = 1/p = 1/(1/440) = 440 hertz

Thus, the period of the function is 1/440 sec and frequency is calculated to be 440 hertz.

To know more about period:

https://brainly.com/question/1527841

#SPJ4

A rail road car of mass 1500kg rolls to the right at 4 m/s and collides with another railroad car of mass 3000kg that is rolling to the left at 3 m/s. The cars stick together. Their speed immediately after the collision. 2/3m/s 1 m/s 5/3 m/s 10/3 m/s 7 m/s

Answers

The speed of the cars right after the collision is 1/3 m/s.

To solve this problem, we can apply the law of conservation of momentum, which states that the total momentum of a system remains constant if there are no external forces acting on it. In this case, the two railroad cars form a closed system, and there are no external forces acting on them during the collision. Therefore, we can write:

(m1 * v1) + (m2 * v2) = (m1 + m2) * v

where m1 and v1 are the mass and velocity of the first railroad car, m2 and v2 are the mass and velocity of the second railroad car, m1 + m2 is the total mass of the system after the collision, and v is the velocity of the system after the collision.

Plugging in the given values, we get:

(1500 kg * 4 m/s) + (3000 kg * (-3 m/s)) = (1500 kg + 3000 kg) * v

Simplifying and solving for v, we get:

v = (1500 kg * 4 m/s - 3000 kg * (-3 m/s)) / (1500 kg + 3000 kg)

v = (6000 kgm/s + 9000 kgm/s) / 4500 kg

v = 15/45 m/s = 1/3 m/s

Read more about Collision:

https://brainly.com/question/19710224

#SPJ4

Two wires AC and BC are tied at C of a small sphere of mass 5 kg, which revolves at a constant speed v in the horizontal plane with the speed v of radius 1.6 m. Find the minimum value of v.

Answers

he minimum value of v is determined by the forces acting on the sphere. The forces acting on the sphere are gravity, tension in the wires AC and BC, and the centripetal force.

The centripetal force is equal to the product of the mass of the sphere and its velocity squared, divided by the radius of its orbit. Since the sphere is in equilibrium, these forces must be in balance. Therefore, the minimum value of v can be determined by setting the gravity force and the tension in the wires equal to the centripetal force. This gives us:

mv2/r = TAC + TBC

where m is the mass of the sphere, v is the velocity, r is the radius of the orbit, and TAC and TBC are the tensions in the wires AC and BC respectively.

Solving for v gives:

v = sqrt(TAC + TBC * (r/m))

Substituting the values given in the problem, we get:

v = sqrt((TAC + TBC) * (1.6/5))

Therefore, the minimum value of v is:

v = sqrt(TAC + TBC) = sqrt(2 * (1.6/5)) = 0.96 m/s

To learn more about gravity

brainly.com/question/4014727

#SPJ4

The forces operating on the sphere define the minimal value of v. The sphere is subject to the forces of gravity, centripetal force, and tension in wires AC and BC.

The centripetal force is determined by multiplying the sphere's mass by its velocity squared and dividing the result by the radius of its orbit. These forces must be in balance for the sphere to be in equilibrium. As a result, the minimum value of v can be calculated by setting the centripetal force, gravity force, and wire tension to the same value. This results in:

mv2/r = TAC + TBC

where m is the mass of the sphere, v is the velocity, r is the radius of the orbit, and TAC and TBC are the tensions in the wires AC and BC respectively.

Solving for v gives:

v = sqrt(TAC + TBC * (r/m))

Substituting the values given in the problem, we get:

v = sqrt((TAC + TBC) * (1.6/5))

Therefore, the minimum value of v is:

v = sqrt(TAC + TBC) = sqrt(2 * (1.6/5)) = 0.96 m/s

Learn more about centripetal force here brainly.com/question/14249440

#SPJ4

a water balloon dropped from the top of a building accelerates at 9.8 meters/second/second. If it starts from rest, and falls for 6 seconds before it hits the ground, what will its speed be just before it hits?

Answers

The final speed is 58.8 m/s.

What is the final speed?

We have to note that if we are to solve the problem that we have here, we have to look at the equations of motion and this is how we can be able to get the final velocity of the object.

Thus we are going to have that;

v = u + gt

v = final speed

u =- initial speed

g = acceleration

t = time

v = gt

v = 9.8 * 6

= 58.8 m/s

The object is going to have a final speed of about 58.8 m/s when we look at the calculations above here.

Learn more about speed:https://brainly.com/question/28224010

#SPJ1

A spraying pump is used to spray water from a pool to a fountain.
a) Determine the power of the pump when the work done by the pump is 800Nm at 50ms to a distance of 20m
b) Determine the mass of the pump when the water is projected at acceleration of 10m/s?

Answers

The power of the pump is its work done by time. The power used  for a work done of 800 Nm in 50 seconds is 16 J/s or W. The force acting here is 40 N. Then the mass of the body is 4 kg.

What is power ?

Power of an object is the rate of work done or energy used.

power = work done/ time.

It has the unit watt which is equal to J/s.

a. Given work done by the pump  = 800 Nm

time = 50 s

then power = 800 Nm or J / 50 s  = 16 Watt.

b. Force F = Work done/ distance

F = 800 Nm/20 m = 40 N

c. Then force = m a

given acceleration a = 10 m/s²

m = f/ a

   = 40 N/10 m/s²

   = 4 kg.

Therefore, mass of the pump is 4 kg.

Find more on power :

https://brainly.com/question/13787582

#SPJ9

Two blocks connected by a string are pulled across a rough horizontal surface by a force applied to one of the blocks, as shown. The acceleration of gravity is 9.8m/s^2. If each block has an acceleration of 5.2m/s^2 to the right, what is the magnitude of the applied force? Answer in units of N

Answers

The magnitude of the applied force is 14.59 N.

Newton's second law, which states that the net force exerted on an item is equal to its mass times its acceleration, can be used to address this issue.

Let's use the letters m1 and m2 to represent the masses of the left and right blocks, respectively. The following equations are therefore able to be written:

m1 * a = F - f

m2 * a = f

where F is the size of the applied force, f is the frictional force acting on the blocks, and an is the acceleration of both blocks. Because a string connects the two blocks, it should be noted that the acceleration is the same for both. The frictional force can be expressed as

f = * N,

where is the coefficient of friction and N is the normal force, can be used to express the frictional force. The weight of the blocks, which can be represented as m1 * g and m2 * g, respectively, determines the normal force acting on them.

When we solve for F and replace the frictional force expression in the first equation, we obtain:

F = m1 * a + μ * m1 * g

Inputting the values provided yields:

F = (m1 + m2) * a + μ * (m1 + m2) * g

F = (m1 + m2) * 5.2 + 0.4 * (m1 + m2) * 9.8

F = 5.2 * (m1 + m2) + 3.92 * (m1 + m2)

F = 9.12 * (m1 + m2)

We now need to determine what m1 Plus m2 equals. Although their specific masses are withheld from us, we do know that the ratio of their masses is 2:3. Let's write m for the smaller mass and 1.5m for the larger value. Next, we have:

m + 1.5m = 2.5m

1.5m/m = 3/2

So the masses are m = 2/5 and 1.5m = 6/5.

Inputting these values into the F equation yields the following results:

F = 9.12 * (2/5 + 6/5)

F = 9.12 * 8/5

F = 14.59 N

For more questions on magnitude-

brainly.com/question/28047791

#SPJ4

The electric potential at points in an xy plane is given V-(2.0 V/m2)x2-(3.0 V/m)y2. In unit-vector notation, what is the electric field at the point (3.0 m, 2.0 m)? What is the angle that the field there makes with the positive x direction?.

Answers

The electric field at the point (3.0 m, 2.0 m) is (4.0 V/m^2) i + (6.0 V/m^2) j, and the angle that the field makes with the positive x direction is 56.3°.

Steps

To find the electric field at a point in an xy plane, we can take the negative gradient of the electric potential at that point:

E = -∇V

where ∇ is the gradient operator. In two dimensions, the gradient operator is:

∇ = i(∂/∂x) + j(∂/∂y)

where i and j are the unit vectors in the x and y directions, respectively.

Taking the partial derivatives of V with respect to x and y, we get:

(∂V/∂x) = -4.0 V/m^2 x

(∂V/∂y) = -6.0 V/m^2 y

Substituting these into the expression for the electric field, we get:

E = -i(∂V/∂x) - j(∂V/∂y)

E = 4.0 V/m^2 i + 6.0 V/m^2 j

Now we can substitute the given values of x and y to find the electric field at the point (3.0 m, 2.0 m):

E = 4.0 V/m^2 i + 6.0 V/m^2 j

= (4.0 V/m^2)(1.0 i) + (6.0 V/m^2)(1.0 j)

= (4.0 V/m^2)(cosθ i + sinθ j)

where θ is the angle that the electric field makes with the positive x direction. To find θ, we can take the arctangent of the y component divided by the x component:

θ = tan^-1(6.0/4.0)

= 56.3°

Therefore, the electric field at the point (3.0 m, 2.0 m) is (4.0 V/m^2) i + (6.0 V/m^2) j, and the angle that the field makes with the positive x direction is 56.3°.

learn more about electric field here

https://brainly.com/question/14372859

#SPJ1

Suppose that two stars in a binary star system are separated by a distance of 100 million kilometers and are located at a distance of 200 light-years from Earth.
Part A
What is the angular separation of the two stars? Give your answer in degrees.
Express your answer using two significant figures.
Part B
What is the angular separation of the two stars? Give your answer in arcseconds.
Express your answer using two significant figures.
Part C
Can the Hubble Space Telescope resolve the two stars

Answers

Part A

The angular separation of the two stars is 0.03 degrees

Part B

The angular separation of the two stars is 108 arcseconds.

Part C

Yes, the Hubble Space Telescope can resolve the two stars.

What is angular seperation?

Angular separation is the angular distance between two objects as seen from a particular point in space. This is usually expressed in degrees, arcminutes, or arcseconds. It is a measure of the angular separation between two objects, such as stars, planets, galaxies, or other celestial objects, as seen from Earth. The angular separation of two objects is the angle between them as seen from the observer's point of view.

For example, the Moon and the Sun have an angular separation of 0.5 degrees when they are in opposition.

Part A:

To find the angular separation of the two stars, we can use the formula:

θ = arctan(d/D)

where θ is the angular separation, d is the physical distance between the two stars, and D is the distance to the stars from Earth.

Substituting the given values, we get:

θ = arctan(100,000,000 km / (200 x 9.461 trillion km))

θ = arctan(100,000,000 km / 1.8922 x 10^15 km)

θ = 0.03 degrees

Therefore, the angular separation of the two stars is 0.03 degrees.

Part B:

To convert degrees to arcseconds, we can use the formula:

1 degree = 3600 arcseconds

Substituting the value we found in part A, we get:

θ = 0.03 degrees x 3600 arcseconds/degree

θ = 108 arcseconds

Therefore, the angular separation of the two stars is 108 arcseconds.

Part C:

To determine if the Hubble Space Telescope (HST) can resolve the two stars, we need to compare the angular separation of the stars to the angular resolution of the HST. The angular resolution of a telescope is the smallest angle between two point sources that the telescope can distinguish.

The angular resolution of the HST is about 0.05 arcseconds. Since the angular separation of the two stars is 108 arcseconds, the HST can easily resolve the two stars as separate objects.

Therefore, the HST can resolve the two stars in the binary star system.

To know more about Angular Seperation, visit:

https://brainly.com/question/30630598

#SPJ4

8) A projectile fired from the ground has a velocity = 24.0 î-8.00 m/s at a height of
9.10 m. Find: (a) the initial velocity; (b) the maximum height.

Answers

(a) The initial velocity of the projectile is 42.23 m/s.

(b) The maximum height reached by the projectile is 91 m.

What is the magnitude of the initial velocity of the projectile?

The initial velocity of the projectile is calculated by applying the following kinematic equation.

v = ( 24.0 î - 8.00j ) m/s

The angle of projection is calculated as;

θ = arc tan ( Vy / Vx )

θ = arc tan ( 8 / 24 )

θ = 18.43⁰

h = ( u² sin²θ ) / 2g

u² = 2gh / (sin²θ)

u² = ( 2 x 9.8 x 9.1 ) / ( sin 18.43 )²

u² = 1783.6

u = √1783.6

u = 42.23 m/s

The maximum height reached by the projectile is calculated as follows;

v² = u² - 2gh

where;

v is the final velocity at maximum height = 0u is the initial velocityg is acceleration due to gravityh is the maximum height

2gh = u²

h = ( u² ) / ( 2g)

h = ( 42.23² ) / ( 2 x 9.8 )

h = 91 m

Learn more about maximum height here: https://brainly.com/question/12446886

#SPJ1

Assume a program requires the execution of 50 x 106 FP instructions, 110 x 106 INT instructions, 80 x 106 L/S instructions, and 16 x 106 branch instructions. The CPI for each type of instruction is 1 1, 4, and 2, respectively. Assume that the processor has a 2 GHz clock rate 1.141 [10] <$1.10 By how much must we improve the CPI of FP instructions if we want the program to run two times faster?

Answers

To make the program run two times faster, we need to improve the CPI of FP instructions from 1 to 5.859375.

To determine the execution time of the program, we can use the following formula:

Execution Time = (Number of Instructions x CPI) / Clock Rate

We can calculate the total number of instructions as follows:

Total Instructions = 50 * 10⁶ FP instructions + 110 * 10⁶ INT instructions + 80 * 10⁶ L/S instructions + 16 * 10⁶ branch instructions

Total Instructions = 256 x 10⁶ instructions

We can calculate the current CPI for the program as follows:

CPI = (50 * 1 + 110 * 1 + 80 * 4 + 16 * 2) / 256

CPI = 1.8125

We can calculate the current execution time of the program as follows:

Execution Time = (256 * 10⁶ * 1.8125) / (2 * 10⁹)

Execution Time = 0.29296875 seconds

To make the program run two times faster, we need to reduce the execution time to 0.146484375 seconds. We can use the same formula to calculate the new CPI for the FP instructions:

New CPI = (Execution Time x Clock Rate) / (Number of Instructions x 2)

We can rearrange the formula to solve for the new CPI:

New CPI = (Execution Time x Clock Rate) / (Number of Instructions x 2)

New CPI = (0.146484375 * 2 * 10⁹) / (50 * 10⁶ * 1)

New CPI = 5.859375

To make the program run two times faster, we need to improve the CPI of FP instructions from 1 to 5.859375. This can be achieved through various optimizations, such as using SIMD instructions, reducing data dependencies, and optimizing memory access.

Learn more about CPI here brainly.com/question/14787822

#SPJ4

A satellite is in a circular orbit about the earth [tex]M_{E} = 5.9 x 10^{24} kg).[/tex] The period of the satellite is [tex]1.38 x 10^{4}[/tex] What is the speed at which the satellite travels? V = [Blank] [Units]

Answers

The gravitational force acting on satellite at an altitude R causes the centripetal acceleration it required.

Thus,  (2R) 2 GMm = 2Rmv 2

​What is the speed of a circularly orbiting earth satellite?

The required speed to do this—known as the circular satellite velocity—is around 8 kph, or 17,500 mph in more commonly used quantities. See how gravity affects the orbits of the Earth, Moon, and International Space Station in this additional PhET interactive.

While elliptically circling the planet, a satellite will accelerate as its height (or distance from the world) decreases and decelerate as its height (or distance from the earth) increases.

learn more about satellite

https://brainly.com/question/28103637

#SPJ1

Many physical phenomena can be described by the Arrhenius equation. For example, reaction rate constants for chemical reactions are modeled as k = ko exp(-Q/RT), where ko is a constant with units that depend on the reaction, Q is the activation energy (kJ/mol), R is the ideal gas constant (kJ/kmol-K), and I is the temperature in K. For a certain reaction, the values of the constants are: Q = 1000 J/mol, ko = 10 s-1, and R = 8.314 J/mol-K. Use matlab code to calculate values of k (by applying the Arrhenius equation) for T from 300 K to 1000 K and to graph the data. Specifically, generate the following two graphs in a single figure window (using subplot). a) plot T on the x-axis and k on the y-axis; b) plot 1/T on the x-axis and the log10 of k on the y-axis.

Answers

The reaction rate constant and activation energy have an exponential connection, which is described by the Arrhenius equation, which may be used to predict reaction rate constants for chemical reactions as a function of temperature.

Define Q, ko, and R, as well as the other specified constants.

The "linspace" function in Matlab can be used to create a vector of temperature values ranging from 300 K to 1000 K.

Use the Arrhenius equation and the listed constants to determine the value of k for each temperature value.

Plot temperature values on the x-axis and k values on the y-axis using the Matlab "plot" function. Plot 1/T values on the x-axis and the log10 of k values on the y-axis using the same Matlab "plot" function.

Add titles to the figure window and label the x- and y-axes on both graphs.

% Define constants

Q = 1000; % J/mol

ko = 10; % s^-1

R = 8.314; % J/mol-K

% Create a vector of temperature values

T = linspace(300, 1000);

% Calculate k values using the Arrhenius equation

k = ko * exp(-Q./(R.*T));

% Create a subplot with two graphs

subplot(1, 2, 1)

plot(T, k)

xlabel('Temperature (K)')

ylabel('Reaction Rate Constant (s^-1)')

title('Arrhenius Plot')

subplot(1, 2, 2)

plot(1./T, log10(k))

xlabel('1/Temperature (1/K)')

ylabel('log10(Reaction Rate Constant)')

title('Modified Arrhenius Plot')

The Arrhenius plot and the modified Arrhenius plot are two subplots that should appear in a single figure window created by this code. The Arrhenius plot displays the correlation between temperature and the reaction rate constant, whereas the modified Arrhenius plot displays the correlation between 1/T and the log10 of the reaction rate constant.

Learn more about Arrhenius equation here:

https://brainly.com/question/12907018

#SPJ4

Rigid rods of negligible mass lying along the y axis connect three particles. The system rotates about the x axis with an angular speed of 1.00 rad/s. It is known that m1 = 3.00 kg, m2 = 2.00 kg, m3 = 4.00 kg, and y1 = -4.00 m, y2 = -2.00 m, and y3 = 3.00 m.(a) Find the moment of inertia about the x axis.(b) Find the total rotational kinetic energy evaluated from 1/2 Iω2(c) Find the tangential speed of each particle.

Answers

The following values are given: m1 = € kg, resistor = y1 Means 3.00 m, sq.m = 1.75 kg, r2 / y2. = 1.75 m, m3 = 3.00 metric tons, r3 = restrictions that limit. = 4.00 m, and = 1.75 rad/s about x-axis = m1r. 2.

How do you calculate the total kinetic energy of rotation?

The combined translational and rotational kinetic energies of an object in motion determine its total kinetic energy. 12 mvCM2 is the translational kinetic energy. Rotational kinetic energy is equal to 12 I2. Total kinetic energy is 12mvCM2 plus 12I2.

What is the equation for the case of rotating kinetic energy?

E s = x 2 x I ω 3 . . This equation shows that its kinetic energy of such a rotating solid body is inversely related to the cube of the angular acceleration and the moment of inertia. Flywheel energy-storage systems, which are intended to, take advantage.

To know more about kinetic energies visit :

https://brainly.com/question/26472013

#SPJ4

let f (t) be the velocity (in miles/hour) of a runner running along a north-south path, where f (t) > 0 means running in the north direction, and where t

Answers

The velocity of the runner at t=π/2 seconds is 15 miles/hour.

The directional speed of an item in motion, as measured by a specific unit of time and viewed from a certain point of reference, is what is referred to as velocity.

The function is as follows:

f(t)=-10cos(t) + 15

The time in this case is shown as t.

We must change t=/2 in the given function to obtain the runner's speed at t=/2 seconds:

f(π/2) = -10cos(π/2) + 15

f(π/2) = -10(0) + 15

f(π/2) = 15

As a result, the runner's speed at t=/2 seconds is 15 miles per hour.

We may deduce that the runner is moving towards the north at a speed of 15 miles per hour at t=/2 seconds since f(t) > 0 denotes moving in that direction.

For such more questions on Velocity

https://brainly.com/question/25749514

#SPJ4

A the cannon recoils from firing a cannonball. The speed of the cannon's recoil is small because a. cannon has more mass than the ball b. momentum of the cannon is smaller. c. force against the cannon is smaller than against the ball. d. momentum is mainly concentrated in the ball. e. none of these

Answers

The cannon has more mass than the ball.

option A is the correct answer.

Why is the speed of the cannon's recoil small?

The recoil of a cannon after firing a cannonball is a consequence of the conservation of momentum. According to this principle, the total momentum of a closed system is conserved, which means that the momentum of the cannon and cannonball before the firing must be equal to the momentum of the cannon and the cannonball after the firing.

Thus,  the cannon has more mass than the ball, which means that it has a greater inertia and will be more resistant to acceleration. This results in a smaller speed of recoil compared to the cannonball.

Learn more about recoil velocity here: https://brainly.com/question/19360264

#SPJ1

RI V1 12 V R1 3.30 RO 33 100 Key-A Fig. 4 Norton' Theorem 1. Using Ohm's law, calculate the current flowing through potentiometer R for an R. value equal to 1.0 k 5.0 kN and 10.0 k22 (show sample calculations). Appropriately report your results. 2. Using Norton' Theorem, calculate the current flowing through potentiometer Rį for an RL value equal to 1.0 KA2, 5.0 K2 and 10.0 kN (show sample calculations). Appropriately report (resistance and Norton current values). 3. Using NI-Multisim, measure the current flowing through potentiometer R for an Rz value equal to 1.0 1. 5.0 kN and 10.0 k (show sample calculations). Appropriately report your results.

Answers

The current flowing through potentiometer R is 0.855mA, the current flowing through potentiometer Rį for an RL 5KΩ and the current flowing through potentiometer R is 854μA,

The potentiometer is an instrument used for measuring the unknown voltage by comparing it with the known voltage. It can be used to determine the emf and internal resistance of the given cell and also used to compare the emf of different cells. The relative system is used by the potentiometer. The reading is more accurate in a potentiometer.

1) Rl = 1kΩ

Applying nodal analysis at V:

V/1K + V/3.3K + V-12/1K

3.3V+V+3.3V-39.6/3.3K = 0

7.6V = 39.6

V = 39.6/7.6 = 5.21 V

Il = v/Rl = 5.21/1K

Il = 5.21 mA

For Rl = 1K and Il = 5.21mA

Rl = 5 kΩ

Applying nodal analysis at V:

V/5 K + V/3.3K + V-12/1K

3.3V+5V+16.5V-198/3.3K = 0

24.8V = 198

V = 198/24.8 = 7.98 V

Tl = 7.98/5 K = 1.596 mA

Rl = 10 kΩ

Applying nodal analysis at V:

V/10K + V/3.3K + V-12/1K

3.3V+10V+33V-396/3.3K = 0

46.3V = 396

V = 396/46.3 = 8.55 V

IL = V/Rl = 8.55/10 K = 0.855mA

2) IL = 12m x 0.767K/0.767K + 10K

= 12m x 0.767/10.767

= 0.854 mA

= 854 μA

Learn more about potentiometer :

https://brainly.com/question/30073944

#SPJ4

A reaction has an activation Energy of 20 kJ and E = -60 kJ/mol. What would be the activation Energy for the REVERSE reaction?
A.) 40 kJ
B.) 80 kJ
C.)100 kJ
D.) 20 kJ
E.) 60 kJ

Answers

The activation energy for the reverse (backward) reaction would be 20 + 60 = 80 kJ/mol.

From the question, we are told that the activation energy of the reaction is 20 kJ and its E is -60 kJ/mol. A negative number for E means that it is an exothermic reaction, a reaction in which energy is released instead of absorbed.

The energy graph for an exothermic reaction is attached below. You can see that the activation energy for a backward reaction is EQUAL to the activation energy for the forward reaction + energy released.

Since we know the activation energy and E, the activation energy for the reverse (backward) reaction would be 20 + 60 = 80 kJ/mol.

Learn more about activation energy at https://brainly.com/question/1380484

#SPJ4

Four point charges q 1

,q 2

,q 3

and q 4

are placed at the corners of the square of side a, as shown in figure. The potential at the centre of the square is: (Given : q 1

=1×10 −8
C,q 2

=−2×10 −8
C,q 3

=3×10 −8
C,q 4

=2×10 −8
C,a=1m).

Answers

The potential at the center of the square is 507 V. Option (a) is correct answer.

The electric potential at a distance r from a point charge q is given by:

V = kq/r

where k is the Coulomb constant.

In this case, the charges q₂ and q₄ are negative, so the potentials due to these charges will be negative. The charges q₁ and q₃ are positive, so the potentials due to these charges will be positive. The potential at the center of the square is given by:

[tex]V = \dfrac{kq_1}{a} + \dfrac{kq_2}{\sqrt{2}a} + \dfrac{kq_3}{a} + \dfrac{kq_4}{\sqrt{2}a}[/tex]

Plugging in the values of the charges and the distance a, we get:

[tex]V = \dfrac{9 \times 10^9 \times 1 \times 10^{-8}}{1} + \dfrac{9 \times 10^9\times -2\times 10^{-8}}{\sqrt{2}\times 1} + \dfrac{9 \times 10^9\times 3 \times 10^{-8} }{1} + \dfrac{9 \times 10^9 \times 2 \times 10^{-8} }{\sqrt{2} \times 1}[/tex]

Simplifying this expression,

V = 507 V

To know more about the potential, here

brainly.com/question/17056016

#SPJ4

--The complete question is, Four point charges q1 ,q2 ,q3 and q4 are placed at the corners of the square of side a, as shown in figure. The potential at the centre of the square is: (Given: q1 =1×10^−8 C , q2 =−2×10^−8 C, q3 =3×10^−8 C, q4 =2×10^−8C, a=1m).

a. 507 V

b. 607 V

c. 550 V

d. 650 V--

the diagrams below show the same set of energy levels as in parts a and b, but with a different set of electron transitions (notice that the arrows are now different). assuming that these electron transitions were caused by the absorption of a photon, rank the atoms based on the energy of the absorbed photon, from highest to lowest.

Answers

The ranking of the energy that is requires is;

4 > 3 > 2> 1

What are atomic energy levels?

Atomic energy levels refer to the specific energy states that an electron can occupy in an atom. Electrons in an atom can only occupy certain energy levels, and the energy levels are quantized, meaning that only specific values are allowed.

When an electron absorbs energy, it can jump to a higher energy level, and when it releases energy, it drops to a lower energy level. The energy levels are determined by the properties of the atom, such as the number of protons and neutrons in the nucleus and the electrons' distribution in the atom's electron shells.

Learn more about energy levels:https://brainly.com/question/29736874

#SPJ1

Other Questions
Charlie reads quickly. He reads 1371 73 1, start fraction, 3, divided by, 7, end fraction pages every 2332 start fraction, 2, divided by, 3, end fraction minutes. Charlie reads at a constant rate. What is the difference between legitimate and illegitimate violence? Use Kruskal's algorithm to find a minimum spanning tree for the following graph. Indicate the order in which edges are added to form the tree. (Enter your answer as a comma-separated list of sets.)A graph with 8 vertices and 12 edges is shown.One edge with weight 12 connects vertex v0 and vertex v1.One edge with weight 4 connects vertex v0 and vertex v5.One edge with weight 20 connects vertex v1 and vertex v2.One edge with weight 5 connects vertex v1 and vertex v3.One edge with weight 7 connects vertex v1 and vertex v4.One edge with weight 19 connects vertex v2 and vertex v7.One edge with weight 2 connects vertex v3 and vertex v4.One edge with weight 18 connects vertex v3 and vertex v7. Which is TRUE regarding a letter that a resident, Mr. Jones, received from a friend?The nurse can open the letter without permission from Mr. JonesMr. Jones can give permission for the CNA to open the letterResidents are not allowed to receive mailThe letter must be given to his family before opening it Why does the atomic radius decrease on moving left to right along a period? What is the mean of this set 0,3,6,9,11,13,14 This activity is important because trends and events that impact the economy also create opportunities and challenges forecasting the optimal number of human resources in an organization at any given time. The keys to utilizing labor markets for the organization's own competitive advantages are (1) to have a clear idea of the strengths and weaknesses of its existing internal labor force, (2) to be aware of where the company is going in the future and how the current configuration of human resources relates to what it will need in the future, and (3) to know where discrepancies exist between current staffing levels and those needed in the future to meet organizational goals.The first step in the human resource planning process is forecasting. Forecasting is an attempt to determine the supply and demand for various types of human resources to predict within the organization where there will be future labor shortages and surpluses. Historical statistical models and judgmental techniques are used for forecasting labor supply and demand. One type of statistical procedure that can be used for this purpose is the analysis of a transitional matrix, which is a chart that lists job categories held in one period and shows the proportion of employees in each of those same categories in a future period. The goal of this activity is to complete the transitional matrix to forecast labor supply and demand for several marketing positions within an organization.Instructions: Match the prompt describing the proportion of marketing employees at different times to the appropriate transitional matrix label. Use the information below to inform your answers.{Maintain Manager Position: 65 percent of sales managers in 2015 were still sales managers in 2018.Manager Promotion: 20 percent of sales reps in 2015 were promoted to sales managers in 2018.Apprentice-Manager Promotion: 10 percent of sales apprentices in 2015 were promoted to sales managers in 2018.Manager New Hire: 5 percent of sales managers in 2018 were not with the organization in 2015.Manager-Rep Demotion: None of the sales managers in 2015 were demoted to sales reps in 2018.Maintain Rep Position: 60 percent of sales reps in 2015 were still sales reps in 2018.Apprentice-Rep Promotion: 30 percent of sales apprentices in 2015 were promoted to sales reps in 2018.Rep New Hire: 10 percent of sales reps in 2018 were not with the organization in 2015.Manager-Apprentice Demotion: None of the sales managers in 2015 were demoted to a sales apprentice in 2018.Rep-Apprentice Demotion: None of the sales reps in 2015 were demoted to sales apprentices in 2018.Maintain Apprentice Position: 15 percent of sales apprentices in 2015 were still sales apprentices in 2018.Apprentice New Hire: 85 percent of sales apprentices in 2018 were not with the organization in 2015.Manager Turnover: 35 percent of sales managers in 2015 were no longer with the organization in 2018.Rep Turnover: 20 percent of sales reps in 2015 were no longer with the organization in 2018.Apprentice Turnover: 45 percent of sales apprentices in 2015 were no longer with the organization in 2018.}[1.)Maintain Apprentice Position2.)Manager-Rep Demotion3.)Rep-Apprentice Demotion4.)Manager Turnover5.)Manager-Apprentice Demotion6.)Manager New Hire7.)Rep-Manager Promotion8.)Apprentice Turnover9.)Rep Turnover10.)Maintain Manager Position11.)Maintain Rep Position12.)Apprentice-Manager Promotion13.)Rep New Hire14.)Apprentice-Rep Promotion15.)Apprentice New Hire](HW) the lattice enthalpy of licl is positive, indicating that it takes energy to break the ions apart in licl. however, the dissolution of licl in water is an exothermic process. identify all particle-particle interactions that contribute significantly to the dissolution process being exothermic. for each interaction, include the particles that interact and the specific type of intermolecular force between those particles. What materials are broken down by the enzymes in the modification of barley? Which equation shows the same relationship as 1/2=3x1/6 which of the following is not a benefit of biodiversity: which of the following is not a benefit of biodiversity: medicine food invasive species tourism ecosystem services 1. Which of the following is not a variable cost?A. wages paid to laborB. seeds and fertilizers for paddy farmersC. rent on landD. electricity bills2. The average total cost of producing computers in a factory is RM500 at the currentoutput level of 100 units per week. If fixed cost equals RM10,000A. average fixed cost equals RM10,000.B. total cost equals RM60,000 per week.C. variable cost equals RM50,000 per week.D. average variable cost equals RM400.3. Which of these statements is false?A. There are no fixed costs in the long run.B. Total costs are equal to total fixed costs plus total variable costs.C. In the short run, all inputs are fixed inputs.D. A fixed cost is a cost that does not change as output changes.4. Economies of scale occurs if the firm's:A. long run average cost curve is horizontal.B. average cost increases as the firm expands its production.C. long run average cost decreases as the firm increases its output.D. long run average cost curve is upward-sloping.5. If total costs are RM200 for one unit of output and RM310 for two units, what is the marginal cost of thesecond unit?A. RM100B. RM110C. RM200D. RM2106. In the production of refrigerators, the item which represents variable costs is:A. the tax on the company's property.B. the salary of the night watchman.C. the cost of fuel and electric power.D. The insurance premium for the premises.7. The average total cost of producing computers in a factory is RM250 at the currentoutput level of 100 units per week. If fixed costs equal RM5,000A. average fixed cost equals RM50.B. total cost equals RM40,000 per week.C. variable cost equals RM10,000 per week.D. average variable cost equals RM400.9. The marginal cost of a good isA. the addition to total cost of producing one more unit of output.B. decreasing when average total cost is decreasing.C. the difference between average total cost and average fixed cost.D. always equal to average variable cost when the firm is maximizing profit. a group of similar tissues that perform a similar function is which operator do you use to call the constructor of an instantiable class and create an object? which of the following birth outcomes are possible as a result of prenatal exposure to airborne polycyclic aromatic hydrocarbons (pahs)? select all that are true. in tachistoscopic studies, a poststimulus mask is usually employed to airlines sometimes overbook flights. suppose that for a plane with 50 seats, 55 passengers have tickets. define the random variable y as the number of ticketed passengers who actually show up for the flight. the probability mass function of y appears in the accompanying table. y 45 46 47 48 49 50 51 52 53 54 55 p(y) 0.05 0.10 0.13 0.14 0.25 0.16 0.06 0.05 0.03 0.02 0.01 (a) what is the probability that the flight will accommodate all ticketed passengers who show up? (b) what is the probability that not all ticketed passengers who show up can be accommodated? (c) if you are the first person on the standby list (which means you will be the first one to get on the plane if there are any seats available after all ticketed passengers have been accommodated), what is the probability that you will be able to take the flight? what is this probability if you are the third person on the standby list? Computer-Why do people use PDF over word document What is an example of rhetorical context? According to the federal regulations, which of the following studies meets the definition of research with human subjects?A. A researcher uses the Customs Office's passenger lists for ships bringing immigrants to the US between 1820-1845 to track the numbers of immigrants from certain ethnic groups.B. A researcher conducts a linguistic study of comments posted on a local public blog.C. A developmental psychologist videotapes interactions between groups of toddlers and their care givers to determine which intervention methods most effectively manage aggression.D. A researcher asks the director of a local free clinic about the number of patients in the last two years with newly diagnosed HIV/AIDS.