The density of blood is 1055 kg/m3 . If the blood at the very top of your head exerts a minimum gauge pressure of 45 mm Hg (6000 Pa), estimate the gauge pressure at your heart in pascals.

Answer:

Collisions may take place between the reactants.

Explanation:

The collision frequency must be greater than the frequency factor for the reaction. A collision between the reactants must occur.

Answer:

5.78amps

Explanation:

Given data

Time t= 57 seconds

Charge Q= 330C

Current I= ??

The expression for the electric current is given as

Q= It

Substituting we have

330= I*57

I= 330/57

I=5.78 amps

Hence the current is 5.78amps

In 2009 Usain Bolt set the world record time by running 100 meters in 9.58 seconds, assuming that he ran this race with constant acceleration, then the required constant acceleration would have been

There are three equations of motion given by  Newton

v = u + at

S = ut + 1/2×a×t²

v² - u² = 2×a×s

By using the second equation of motion given by Newton,

S = ut + 1/2at²

100= 0 + 0.5*a*9.58²

a = 2.17 meters / second²

Thus,the required constant acceleration of Usain Bolt would have been 2.17 meters / second².

To learn more about equations of motion here, refer to the link;

brainly.com/question/5955789

#SPJ2

Answer:

c)  N_s / N_p = 115.15

Explanation:

Let's look for the voltage in the secondary, they do not indicate the power dissipated

          P = V_s i

          V_s = P / i

          V_s = 76 / 5.5 10⁻³

          V_s = 13.818 10³ V

the relationship between the primary and secondary of a transformer is

           [tex]\frac{V_p}{N_p} = \frac{V_s}{N_s}[/tex]

           [tex]\frac{N_s}{N_p} = \frac{V_s}{V_p}[/tex]

           Ns / Np = 13,818 10³ /120

           N_s / N_p = 115.15

Answer:

-700

formula is heat gained - work done

The change in internal energy if A system gains 1500J of heat and 2200J of work is done by the system on its surroundings, is 700 joules.

Energy is the ability to perform work in physics. It could exist in several different forms, such as potential, kinetic, thermal, electrical, chemical, radioactive, etc.

Additionally, there is heat and work, which is energy being transferred from one body to another. Energy is always assigned based on its nature once it has been transmitted. Thus, heat transmitted may manifest as thermal energy while work performed may result in mechanical energy.

Given:

A system gains 1500J of heat and 2200J of work is done by the system on its surroundings,

Calculate the change in internal energy as shown below,

The change in internal energy = heat gained - work done

The change in internal energy = 1500 - 2200

The change in internal energy = -700 J

Thus, the change in internal energy is 700 joules.

To know more about Energy:

https://brainly.com/question/8630757

#SPJ5

Answer:

[tex]F=208.83N[/tex]

Explanation:

From the question we are told that:

Acceleration [tex]a=2.4m/s^2[/tex]

Force of Branch [tex]F=260N[/tex]

Generally the Newton's equation second law for Force is mathematically given by

 [tex]ma=F-mg[/tex]

 [tex]m=\frac{260}{2.4+9.8}[/tex]

 [tex]m=21.31kg[/tex]

Therefore

 [tex]F=mg[/tex]

 [tex]F=(21.31)(9.8)[/tex]

 [tex]F=208.83N[/tex]

Explanation:

No matter where you are in the universe, your mass is always the same: mass is a measure of the amount of matter which makes up an object. Weight, however, changes because it is a measure of the force between an object and body on which an object resides (whether that body is the Earth, the Moon, Mars, et cetera).

Explanation:

Hence, weight of a body will change from one place to another place because the value of g is different in different places. For example, the value of g on moon is 1/6 times of the value of g on earth. As mass is independent of g , so it will not change from place to place.

Answer:

7.8% of the original volume.

Explanation:

From the given information:

Temperature [tex]T_1[/tex] = 22° C = 273 + 22 = 295° C

Pressure [tex]P_1[/tex] = 240 kPa

Temperature [tex]T_2[/tex] = 45° C

At initial temperature and pressure:

Using the ideal gas equation:

[tex]P_1V_1 =nRT_1[/tex]

making V_1 (initial volume) the subject:

[tex]V_1 = \dfrac{nRT_1}{P_1}[/tex]

[tex]V_1 = \dfrac{nR*295}{240}[/tex]

Provided the pressure maintained its rate at 240 kPa, when the temperature reached 45° C, then:

the final volume [tex]V_2[/tex] can be computed as:

[tex]V_2 = \dfrac{nR*318}{240}[/tex]

Now, the change in the volume ΔV =  V₂ - V₁

[tex]\Delta V = \dfrac{nR*318}{240}- \dfrac{nR*295}{240}[/tex]

[tex]\Delta V = \dfrac{23nR}{240}[/tex]

∴

The required fraction of the volume of air to keep up the pressure at (240) kPa can be computed as:

[tex]= \dfrac{\dfrac{23nR}{240}}{ \dfrac{295nR}{240}}[/tex]

[tex]= {\dfrac{23nR}{240}} \times { \dfrac{240}{295nR}}[/tex]

[tex]= 0.078[/tex]

= 7.8% of the original volume.

Answer:

The velocities of the skaters are [tex]v_{1} = 3.280\,\frac{m}{s}[/tex] and [tex]v_{2} = 0.024\,\frac{m}{s}[/tex], respectively.

Explanation:

Each skater is not under the influence of external forces during process, so that Principle of Momentum Conservation can be used on each skater:

First skater

[tex]m_{1} \cdot v_{1, o} = m_{1} \cdot v_{1} + m_{b}\cdot v_{b}[/tex] (1)

Second skater

[tex]m_{b}\cdot v_{b} = (m_{2}+m_{b})\cdot v_{2}[/tex] (2)

Where:

[tex]m_{1}[/tex] - Mass of the first skater, in kilograms.

[tex]m_{2}[/tex] - Mass of the second skater, in kilograms.

[tex]v_{1,o}[/tex] - Initial velocity of the first skater, in meters per second.

[tex]v_{1}[/tex] - Final velocity of the first skater, in meters per second.

[tex]v_{b}[/tex] - Launch velocity of the meter, in meters per second.

[tex]v_{2}[/tex] - Final velocity of the second skater, in meters per second.

If we know that [tex]m_{1} = 70\,kg[/tex], [tex]m_{b} = 0.043\,kg[/tex], [tex]v_{b} = 32\,\frac{m}{s}[/tex], [tex]m_{2} = 58.5\,kg[/tex] and [tex]v_{1,o} = 3.30\,\frac{m}{s}[/tex], then the velocities of the two people after the snowball is exchanged is:

By (1):

[tex]m_{1} \cdot v_{1, o} = m_{1} \cdot v_{1} + m_{b}\cdot v_{b}[/tex]

[tex]m_{1}\cdot v_{1,o} - m_{b}\cdot v_{b} = m_{1}\cdot v_{1}[/tex]

[tex]v_{1} = v_{1,o} - \left(\frac{m_{b}}{m_{1}} \right)\cdot v_{b}[/tex]

[tex]v_{1} = 3.30\,\frac{m}{s} - \left(\frac{0.043\,kg}{70\,kg}\right)\cdot \left(32\,\frac{m}{s} \right)[/tex]

[tex]v_{1} = 3.280\,\frac{m}{s}[/tex]

By (2):

[tex]m_{b}\cdot v_{b} = (m_{2}+m_{b})\cdot v_{2}[/tex]

[tex]v_{2} = \frac{m_{b}\cdot v_{b}}{m_{2}+m_{b}}[/tex]

[tex]v_{2} = \frac{(0.043\,kg)\cdot \left(32\,\frac{m}{s} \right)}{58.5\,kg + 0.043\,kg}[/tex]

[tex]v_{2} = 0.024\,\frac{m}{s}[/tex]

Answer:

Answer:

586 K

Explanation:

Let P is the initial pressure.

Initial temperature, T₁ = 20°C = 293 K

Final pressure, P₂ = 2P

We need to find the final temperature of the gas.

The relation between the pressure and the temperature is as follows

[tex]P\propto T\\\\or\\\\\dfrac{P_1}{P_2}=\dfrac{T_1}{T_2}[/tex]

Put all the values,

[tex]\dfrac{P}{2P}=\dfrac{293}{T_2}\\\\\dfrac{1}{2}=\dfrac{293}{T_2}\\\\T_2=2\times 293\\\\T_2=586\ K[/tex]

So, the final temperature of the gas is 586 K.

Answer:

converts elastic energy to mechanical energy

Explanation:

Answer:

answer here

Explanation:

the unit of work is fundamental unit because it doesn't depend on other units.

__________________

Thx

Answer:

The SI unit of work is joule (J)

Explanation:

Joule is a derived unit. ∴ unit of work is a derived unit

Answer:

Explanation:

For starters begin with a warning not to touch the brake drums. All of the KE is transferred to the brake drums. The result is a large rise in temperature. Heat. If you press hard on the brakes, rubber is left on the road and there is heat involved in that too.

Answer:

KInetic energy reduces.

Explanation:

Application of breaks reduces velocity. Reduction of velocity constitutes velocity reduction.

For more help contact +1 (304) 223-3136

Answer:

the speed of the nerve impulse in miles per hour is 201.59 mi/hr

Explanation:

Given;

the speed of the nerve impulse, v = 90.1 m/s

To convert this speed in meters per second to miles per hour, we use the following method;

1,609 meter = 1 mile

3,600 s = 1 hour

[tex]v(mi/h) = 90.1 \ \frac{m}{s} \times \frac{1 \ mile}{1,609 \ m} \times \frac{3,600 \ s}{1 \ hour} = (\frac{90.1 \times 3,600}{1,609} )\frac{mi}{hr} = 201.59 \ mi/hr[/tex]

Therefore, the speed of the nerve impulse in miles per hour is 201.59 mi/hr

Answer:

A cylindrical specimen of aluminum having a diameter of 0.505 in. (12.8 mm) and a gauge length of 2.0 in. (50.8 mm) is pulled in tension. Use the load-elongation characteristics tabulated below to complete parts (a) through (f).

Answer:

Explanation:

Since the compass uses a magnetic field, if anything else magnetic is near it, the compass will start acting up. Making it unreliable so keep magnets away!

As the spring is stretched, it exerts an upward restoring force f. At maximum extension, Newton's second law gives

∑ F = f - mg = 0   ==>   f = (2.0 kg) (9.8 m/s²) = 19.6 N

By Hooke's law, if k is the spring constant, then

f = kx   ==>   k = f/x = (19.6 N) / (0.15 m) ≈ 130 N/m

A 4.0 kg mass would cause the spring to exert a force of

f = (4.0 kg) (9.8 m/s²) = 39.2 N

which would result in the spring stretching a distance x such that

39.2 N = (130 N/m) x   ==>   x = (39.2 N) / (130 N/m) ≈ 0.30 m ≈ 30 cm

This above answer helps a lot.

Answer:

W = 4.75 KW

Explanation:

First, we will calculate the heat to be removed:

Q = (No. of students)(Metabolic Power of Each Student)

Q = (190)(125 W)

Q = 23750 W = 23.75 KW

Now the formula of COP is:

[tex]COP = \frac{Q}{W}\\\\W = \frac{Q}{COP}\\\\W = \frac{23.75\ KW}{5}\\\\[/tex]

W = 4.75 KW

Answer:

Block A velocity is 23.33 m/s and the collission is not elastic.

Explanation:

a) m1v1 + m2v2 = m1v1' + m2v2'

Plug in givens

90+60=3v1'+80

solve for v1'= 23.33m/s

b) Find the initial and final kinetic energy of Block B

Ki= 1/2(4)(15)^2 + 1/2(3)(30)^2 = 1800 J

Kf= 1/2(4)(20)^2 + 1/2(3)*(23.33)^2= 1616.433J

Since Ki does not equal Kf the collision is not elastic

Answer:

hope it helps

much as you can

Answer:

The mass and atomic numbers don't change

Explanation:

An excited atom relaxes to the ground state emitting a photon...called a gamma ray.

The answer is that the mass and atomic numbers don't change.

In gamma decay, the product refers to the nucleus resulting from the emission of a gamma ray. Gamma decay occurs when an excited atomic nucleus releases excess energy in the form of a high-energy photon called a gamma ray.

To find the product of gamma decay, you need to identify the nucleus before and after the decay process. The product nucleus is determined by the parent nucleus that undergoes gamma decay.

During gamma decay, the number of protons and neutrons in the nucleus remains unchanged. Therefore, the identity of the element remains the same, but the energy state of the nucleus is altered.

The product nucleus is typically represented by the same chemical symbol as the parent nucleus, followed by a superscript indicating the mass number (total number of protons and neutrons) and a subscript indicating the atomic number (number of protons).

For example, if a parent nucleus with an atomic number of Z and a mass number of A undergoes gamma decay, the product nucleus will have the same atomic number Z and mass number A.

It's important to note that gamma decay does not involve the emission or absorption of any particles, only the release of electromagnetic radiation (gamma ray).

Thus, the product nucleus remains unchanged in terms of atomic number and mass number.

Know more about gamma decay:

https://brainly.com/question/16039775

#SPJ4

Answer:

Gradual shifting of a time series to relatively higher or lower values over a long period of time is called a Trend.

Answer:

the correct is C

Explanation:

The concept of a frame of reference is of crucial importance in physics, because it is the system from which measurements are made. Therefore, the relationships between the different reference frames must be clear so that the measurements made can be compared correctly.

In this case, the first observed sees the movement of the ball, suppose it moves a distance r, the second observed is next to me, separated by a distance x, therefore a frame of reference located in the movement of the ball. ball r '.

Consequently, the measurement carried out is related by

             r = r’ + x

where the bold letters indicate wind blowers.

With these explanations we review the different answers, the correct one is C