The given statement "While merging scenarios, one should keep both workbooks from which one wants to merge scenarios open, and work from the workbook to which one will add the scenarios" is false because when merging scenarios in Excel, you do not need to keep both workbooks open.
Should scenarios be merged by keeping both workbooks open?When merging scenarios in Excel, it is not necessary to keep both workbooks open. Instead, it is more efficient to work from the workbook to which you intend to add the scenarios. To merge scenarios, you can open the destination workbook and navigate to the worksheet where you want the scenarios to be merged.
Then, go to the "Data" tab, click on "What-If Analysis," and select "Scenario Manager." In the Scenario Manager dialog box, you can add, edit, or delete scenarios and import them from other workbooks. This approach simplifies the process and ensures that the scenarios are accurately merged into the desired workbook.
Learn more about Excel
brainly.com/question/30324226
#SPJ11
Problem 2: When the input to a given audio amplifier is 4cos(800nt) + cos (1000nt) mV, the
measured frequency component at 1000Hz is 1V and the ratio of the frequency components at
500 Hz to that at 1000 Hz is 0.002. Represent the amplifier output-input characteristic by
Uo (t) = aqui (t) + az lu; (t) ]2.
a) Evaluate the numerical values of a1, a2 from the test data given. This type of test is known
as the intermodulation distortion test.
b) What would you expect to be magnitudes of the frequency component at 800 Hz and at
1600 Hz?
The numerical values of a2 = 0.002*a1 / 16
The magnitudes of the frequency component at 800 Hz and at
1600 Hz are: 4²a2cos²(800nt) and 8²a2cos²(800nt)cos²(1000nt)
What is the numerical values?a) To evaluate the numerical values of a1 and a2, we can use the test data given. The measured frequency component at 1000 Hz is 1V, so we can set that as the value of a1cos(1000nt) in the amplifier output equation:
Uo(t) = a1cos(1000nt) + a2[4cos(800nt) + cos(1000nt)]²
The ratio of the frequency components at 500 Hz to that at 1000 Hz is 0.002, so we can use that to find the value of a2:
Uo(t) = a1cos(1000nt) + a2[4cos(800nt) + cos(1000nt)]²
= a1cos(1000nt) + a2[16cos²(800nt) + 8cos(800nt)cos(1000nt) + cos²(1000nt)]
= a1cos(1000nt) + a2(16cos²(800nt) + 8cos(800nt)cos(1000nt) + cos²(1000nt))
The frequency component at 500 Hz is the second harmonic of the 800 Hz component and is given by 16cos²(800nt), so we can compare it to the 1000 Hz component:
16cos²(800nt) = 0.002 * a1cos(1000nt)
a2 = 0.002*a1 / 16
b) Since the input to the amplifier is a sum of cosine functions with different frequencies, the output will also be a sum of cosine functions with the same frequencies, but with different amplitudes.
The 800 Hz component in the input is 4cos(800nt) and is squared in the output equation, so the 800 Hz component in the output will be 4^2a2cos^2(800nt) which is a smaller amplitude than the 800 Hz component in the input.
The 1600 Hz component in the input is created by the product of the 800 Hz component and the 1000 Hz component, which is 8cos(800nt)cos(1000nt) and is squared in the output equation. so the 1600 Hz component in the output will be 8^2a2cos^2(800nt)cos^2(1000nt) which is even smaller than the 800 Hz component in the input.
Learn more about audio amplifier from
https://brainly.com/question/15610180
#SPJ1
elivery Execution Knowledge Check Question 1 of 8. When you walk into the station at the end of your route, what should you do? Check in with your DSP and being any undeliverable packages back to the Amazon Retum to Station desk O leave the undeliverable packages with your OSP then go off duty You don't have to return to the station at the end of your day Sign out of your device and love Mark for foto up
Answer:
ur hhbkiegtbckdj you and your family a very merry merry
Where would an engineer indicate the unit of measurement used in a design
An engineer would indicate the unit of measurement used in a design in millimeters.
What are measurements?The primary unit of measurement is the stocking unit of measure for a given item in a specific organization. You must define an item attribute that serves as the primary unit of measurement when creating each item.
Because the technical drawings are scaled, engineers, architects, and builders may create the items according to exact specifications.
When understanding scales, the number on the left relates to the measurement of the drawing, while the number on the right represents the actual size of the object.
Therefore, a millimeter is used in a design.
To learn more about measurements, refer to the link:
https://brainly.com/question/28390923
#SPJ1
Classify each of the structures as statically determinate, statically indeterminate, or unstable. If indeterminate, specify the degree of indeterminacy. The supports or connections are to be assumed as stated.
The structure a) is indeterminate. The structures b, c, and d are statically indeterminate.
We know that if
r = 3n (Statically determinate)
r > 3n (Statically indeterminate)
r < 3 n (unstable)
r \geq 3n (unstable if reactions are concurrent or parallel)
where r = no.of reactions
n = no of parts
a) r = 2+2+1 = 5
n = 1, 3n = 3x1 = 3
5 > 3
Indeterminate upto 5 - 3 = 2 degrees
b) Unstable as all reactions are parallel
c) r = 3
n = 1 , 3(1) = 3
r = 3n
Statically Determinate
d) r = 2+2+2 = 6
n =2 , 3(2) = 6
r = 3n
Statically Determinate
e) Unstable as the reactions are concurrent meeting at common point
Frames can be classified by cutting closed loops and finding reactions
At each cutaway section three unknown forces are generated
b) 8 cuts are required generating 8x3 = 24 forces and 3 members
r = 24 +2+2+3 = 31
n = 3. r = 3(3) = 9
31 - 9 = 22
Indeterminate upto 22 degrees
c) 6 cuts are required generating 6x3 = 18 forces and 4 members
r = 18 + 3 + 3 = 24
n = 4 , 3(4) =12
24 - 12 = 12
Statically Indeterminate upto 12 degrees
To learn more about structures
https://brainly.com/question/10730450
#SPJ4
Solve the differential equation by variation of parameters. (Use C1 and C2 as arbitrary constants.)
y'' − 16y = 16x/e^4x
Refer to the attached images. Final answer is circled.
Consider the following piece of C code:
for (j = 2; j < 1000; j++)
D[j] = D[j − 1] + D[j − 2];
The MIPS code corresponding to the above fragment is:
addiu $s2, $zero, 8000
addiu $s1, $zero, 16
loop: l.d $f0, -16($s1)
l.d $f2, -8($s1)
add.d $f4, $f0, $f2
s.d $f4, 0($s1)
addiu $s1, $s1, 8
bne $s1, $s2, loop
Re-write the assembly code above so that the loop is unrolled by 4 iterations.
CPU SS: A two-core superscalar processor with two function units that can handle out-of-order issues (FUs). On each core, only one thread can be active at once. CPU MT.
a fine-grained multithreaded processor that enables simultaneous execution of instructions from two threads (i.e., there are two functional units), but only one thread's worth of instructions can be issued at a time. CPU SMT: A SMT processor that has two functional units and supports running instructions from two threads simultaneously. Instructions from either or both threads may be sent to execute on any cycle. A high-level, all-purpose programming language is the C language. It offers a simple, reliable, and effective interface for system programming.
Learn more about function here-
https://brainly.com/question/17216645
#SPJ4
2.35 Calculate Vo and Io in the circuit of Fig. 2.99
Vo and Io in the circuit is v^0=32V And I^0=0.8 A
Step by step explanation:
Given circuit:
Resultant equivalent resistance is
R^ e q=(700||30)+(20||5)
=21+4
R^ e q=25
Total current=v/R^ e q
I=200/25
I=8A
Therefore ,Apply nodal analysis at v^ 1
v^ 0=v^1
200-V0/70+ 200-v^ 0/30=8
6000-30v^0+14000-70v^0/2100=8
20000-100v^0/2100=8
=20000-100v^0=16800
=100v^0=3200
v^0=3200/100
v^0=32V
Apply nodal at V^ 2.
I^0=V^0-200/30+v^0/5
I^0=32-200/30+32/5
I^0=-168/30+32/5
I^0=-5.6+6.4
I^0=0.8 A
What Does Equivalent Resistance Mean?
An equivalent resistance is defined in physics as the sum of the resistances of the resistors connected in a circuit. Resistors can be wired in series or parallel. Assume that the three resistors are R1, R2, and R3.
If you connect these three resistors in series, the equivalent resistance is given by
Re = R1 + R2 + R3
To learn more about Vo and Io in the circuit
https://brainly.com/question/13889633
#SPJ4
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Taking h=9 mm and using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Brass h Aluminium 30 mm 30 min Aluminum Brass . Modulus of elasticity 70 GPa 105 GPa Allowable stress 100 MPa 160 MPa
The largest permissible bending moment is____ KN m
According to the question, the largest permissible bending moment is 1382.5 KN m.
What is bending moment?
Bending moment is a mechanical force that causes a bending or flexing effect on a structural element such as a beam, resulting in the creation of a moment or torque about the element's neutral axis. It is calculated based on the internal forces acting on the element, such as the weight of the beam and the force of the load applied to it. Bending moment can be positive or negative, depending on the direction of the force and the location of the neutral axis.
M = (h×A×E×σ_allowable)/6
M = ((9mm×30mm×70GPa×100MPa)+(9mm×30mm×105GPa×160MPa))/6
M = 1382.5 KN m
To learn more about bending moment
https://brainly.com/question/13390572
#SPJ4
A child having a mass of 50 kg holds her legs up as shown as she swings downward from rest at ?1=30o . Her center of mass is located at point G1 (a radius of 2.8 m from the origin). When she is at the bottom position of ?=0o , she suddenly lets her legs come down, (approximately instantaneously) shifting her center of mass to position G2 (a radius of 3 m from the origin). Determine her speed in the upswing immediately following the change in the position of her center of mass. (Think about what quantity has changed now that her center of mass is further from origin.) Also find the angle ?2 to which she swings before momentarily coming to rest. Treat the child’s body as a particle. HINT: Think about this problem in 3 phases: 1) Swinging from initial position to vertical position with legs up, 2) Instantaneously bending legs while in vertical position, and 3) swinging from vertical to final position with legs bent.....Answer: v2 = 2.53 m/s, ?2=27o......Please show a clear and understandable solution
For a kid weighing 50 kg, does she hold her legs up when she swings down from rest at? 1 = 30° and Ф2 = 27°
Fint prior to = 0 T1 9V1 = T2 + V2 0 + 2.8 (1-cos30) (50) 9.81 = 1/2 (50) (50) V12 plus 0 V1 equals 2.713 m/sec
H1 = H2 \s50(2.713)(2.8) = 50 V2 (3) (3)
V2 = 2.532 =2.53 m/sec immediately following = 0, T2 +V2 = T2, V3 1/2 850(2.532)2, and 50(9/81)(3). (1-cos02)
27 degree is equal to 0.1089 = 1-cos02 2.
Children grow and develop in certain ways. They must be able to sit up on their own, for instance, before they can swings and subsequently walk. The same is true for how they master penmanship. Before the child can write, they tear, cut, and scribble on things. Before kids can hold a pencil and form readable symbols, called letters, in their hands, they must first develop the tiny muscles (fine motor muscles).
Learn more about Swing here:
https://brainly.com/question/1230851
#SPJ4
For the frame and loading shown, determine the components of all forces acting on member ABE when P = 13.8 kN. (Round the final answers to two decimal places.)
When examining a force's geometric representation or its algebraic equivalent, the components of a force can be viewed as horizontal and vertical changes.
The vertical and horizontal forces that combine to create the resulting force are represented by a force's components. A force can be broken down into two parts that are either inclined or perpendicular to one another. Two components are referred to as rectangular components when they are perpendicular to one another and as inclined components when they are inclined toward one another. Force has two parts: magnitude and direction. When examining a force's geometric representation or its algebraic equivalent, the components of a force can be viewed as horizontal and vertical changes.
Learn more about magnitude here-
https://brainly.com/question/13686176
#SPJ4
The two blocks shown are originally at rest. Neglecting the masses of the pulleys and the effect of friction in the pulleys and between the blocks and the inclines, determine (a) the acceleration of each block, (b) the tension in the cable.
The acceleration of block A is 8.4949 and block B is 4.2475 ft/s² while the tension is the cable is 121.168 lb.
What is tension?When there are two forces acting on the ends of a cable, rope, wire, or string, it is said to be under tension. The cable has a one-direction pull along its entire length, pulling equally in both directions on objects at either end.
Tension can also be used to describe the forces that are acting on both ends of the two elements. In other words, tension's polar opposite is compression.
Physical objects must exert some force on one another in order to make contact with one another. Depending on the kind of object, each of these contact forces will be unique.
Take a section about the rope near block B and using the show datum
SB + (SB - SA) = l
2SB - SA = l
2SB - SA = 0
2aB - aA = 0
aA = 2aB
Take FBD of block-A
(Upward+) ∑Fₓ = mAaA
T - W[tex]_A[/tex]sin20° = mAaA
T - 200sin20° = (W[tex]_A[/tex]/g)(2aB)
T = 200sin20° + (W[tex]_A[/tex]/g)(2aB)
Take FBD of block-B;
(Downward+) ∑Fₓ = mBaB
W[tex]_B[/tex]cos20° - 2T = mAaA
300cos20° - 2(200sin20° + (W[tex]_A[/tex]/g)(2aB)) = (W[tex]_B[/tex]/g)(a[tex]_B[/tex])
300cos20° - 2(200sin20° + (200/32.2)(2aB)) = (300/32.2)(a[tex]_B[/tex])
a[tex]_B[/tex] = 4.2475 ft/s²
Acceleration of A is given as;
⇒ aA = 2aB
⇒ aA = 8.4949 ft/s²
Tension is given as;
T = 200sin20° + (200/32.2)(2(4.2475))
T = 121.168 lb
Thus, the acceleration of block A is 8.4949 and block B is 4.2475 ft/s² while the tension is the cable is 121.168 lb.
Learn more about tension
https://brainly.com/question/11348644
#SPJ4
© 2022. Grand Canyon University. All Rights Reserved.APA Activity 2: Citing PracticeCreate a reference page by citing the following sources in correct APA format. You may use your text or the GCU Library website to help you, but do not use citation generators.•A textbook: The second edition of Psychology and Your Life by Robert S. Feldman written in 2013. The publishing city is New York, New York published from McGraw Hill Companies.•Snickers commercial https://youtu.be/2rF_FRCd_LA •PBS Frontline special League of Denial •The document found at this address:http://www.eia.gov/forecasts/aeo/er/pdf/0383er(2013).pdf•The movie Silver Linings Playbook•The episode of Friends titled: The One After Joey and Rachel Kiss•The 7th edition of the APA Manual
Using APA reference style, the references is attached below from Feldman, R. S. (2013) to American Psychology Association (2020)
What is APA Reference StyleAPA reference style is a style of citing sources used by the American Psychological Association. It is primarily used in the social sciences and includes guidelines for citing sources both within the text of a document and in the reference list at the end of the document. The guidelines provide a consistent way of citing sources to make it easier for readers to identify and locate the sources cited in a document.
In the given problem, if we need to write the reference using APA style, it will take this format below
Reference Page:
Feldman, R. S. (2013). Psychology and your life (2nd ed.). New York, NY: McGraw Hill Companies.
Frontline. (n.d.). League of denial. Retrieved from https://www.pbs.org/wgbh/frontline/film/league-of-denial/
Friends. (2004). The one after Joey and Rachel kiss [Television series episode]. In D. Crane, & M. Kauffman (Executive producers), Friends. Burbank, CA: Warner Bros. Television.
Silver Linings Playbook. (2012). [Motion Picture]. United States: The Weinstein Company.
U.S. Energy Information Administration. (2013). Annual energy outlook 2013 with projections to 2040. Retrieved from http://www.eia.gov/forecasts/aeo/er/pdf/0383er(2013).pdf
Snickers. (2013, April 2). You’re not you when you’re hungry [Video file]. Retrieved from https://youtu.be/2rF_FRCd_LA
American Psychological Association. (2020). Publication manual of the American Psychological Association (7th ed.). doi:10.1037/0000165-000
Learn more on APA reference style here;
https://brainly.com/question/28008158
#SPJ1
Gain bode diagram of minimum phase as follow dash line is original L0(w0), solid line is compensated L(w)
The amount of gain that can be raised or lowered without causing the system to become unstable is referred to as the gain margin.
What is the gain in a Bode diagram?The gain margin is the maximum gain that can be achieved without causing the system to become unstable. Typically, a magnitude in dB is used to express it. Usually, the Bode plot can be used to immediately read the gain margin.Remember that the magnitude Bode plot moves upward as we increase system gain. Additionally, the crossover frequency is shifted to the right. Phase margin indicates relative stability, or the propensity to oscillate during its damped response to an input change like a step function. Typically, when the crossover frequency advances to the right, the crossover frequency approaches the frequency where the phase is -180 degrees. Gain margin shows unwavering stability and the maximum amount that the system can oscillate.
Learn more about Bode plot refer to :
https://brainly.com/question/28029188
#SPJ1
List the point coordinates for all atoms that are associated with the FCC unit cell (See Figure a) (b Figure 3.1 Face centered cubic crystal structure, (a) a hard sphere unit cell representation, (b) a reduced-sphere unit cell, and (c) an aggregate of many atoms.
The point coordinates for all atoms that are associated with the FCC unit cell, i.e. fig b are:
bottom face: (1,0,0) (1,1,0) (0,1,0) (1/2,1/2,0)
Tope face: (0,0,1) (1,0,1) (1,1,1) (0,0,1) (1/2,1/2,1)
front and back face: (1/2,1,1/2) (1/2,0,1/2)
Left and Right face: (0,1/2,1/2) (1,1/2,1/2)
What is FCC unit cell?Atoms are found in an FCC unit cell at the centre of each cube's face and at each of the crystal lattice's four corners. Only half of each atom, which is located at the face centre, belongs to one particular cell and is shared by two adjacent unit cells.
A crystal lattice in an FCC unit cell contains atoms in each corner. Additionally, every cube face has an atom in the centre of it. Two next-to-one another unit cells share this face-center atom. A unit cell only contains 12 of each atom.
Learn more about FCC unit cell
https://brainly.com/question/12977980
#SPJ4
A binary tree has L leaves and K nodes, each with two children. What is the relation of L and K ?
Option
L = K -1
L = 2K + 1
L = K - 1
There is no fixed relation between L and K
K=2*L-1 is the relationship between the number of nodes (K) and leaves (L). Therefore, L and k do not always have a stable relationship.
Number of internal nodes for L leaves = L - 1
So total nodes = 2L – 1
The following relation applies for a k-ary tree where each node has k offspring or none at all: L = (k-1)*n + 1.
where n represents the number of internal nodes and L represents the number of leaf nodes.
Every internal node will have K children since the k tree is fully developed.
A pointer to the topmost node of the tree, sometimes referred to as the "root," serves as the representation of a binary tree. The root's value is NULL if the tree is empty. The following components are present in each node of a binary tree:
Pointer to left kid in data
to the right-hand kid
Basic Binary Tree Operation:
adding a new element.
Learn more about Nodes here:
brainly.com/question/24068343
#SPJ4
2 psia is equivalent to
A. 29 in. Hg.
B. 28 in. Hg.
C. 27 in. Hg.
D. 26 in. Hg.
In order to determine absolute pressure, a complete vacuum is used. While the average atmospheric surface pressure is approximately 14.7 PSIA.
The pressure in a vessel absolutely devoid of any air molecules would be 0 PSIA. PSIA stands for absolute pounds per square inch. Absolute pressure is the pressure exerted with relation to absolute zero or vacuum. Engineering documents or P&IDs might employ PSIA. Pounds per square inch gauge is referred to as PSIG. PSIA is a word used to describe absolute pressure in PSI, which includes atmospheric pressure. "Total pressure" is another name for absolute pressure. We add 14.7 PSI since this atmospheric pressure is comparable to 14.7 PSI at sea level. Higher heights have lower atmospheric.
Learn more about engineering here-
https://brainly.com/question/27162243
#SPJ4
When is Environmental Impact Assessment required?
Environmental Impact Assessment (EIA) is often required for significant development projects such as road construction, building construction, and industrial facility construction in order to analyze and minimize any environmental repercussions.
What is Environmental Impact Assessment?It is to be noted that the process of determining how a project or activity will affect the environment is known as environmental impact assessment.
It assists individuals in ensuring that the project will not hurt animals, plants, or natural resources. This manner, we can be sure that the things we construct or do won't affect the world.
Learn more about Environmental Impact Assessment:
https://brainly.com/question/30120335
#SPJ1
The bridge girder G of a bascule bridge is raised and lowered using the drive mechanism shown. If the hydraulic cylinder AB shortens at a constant rate of 0.15 m/s, determine the angular velocity of the bridge girder at the instant theta 0= 60°
According to the question, The bridge girder's angle of rotation at theta 0 = 60° is 0.18 rad/s.
What exactly is velocity?Velocity is the direction at which an item is moving and serves as a measure of the rate at which its location is changing as seen from a certain point of view and as measured by a particular unit of time (for example, 60 km/h northbound). In kinematics, the field of classical mechanics that deals with the motion of objects, velocity is a basic idea. A physical vector quantity called velocity . It must have both a magnitude and a direction in order to be defined. Speed is the scalar absolute value (magnitude) of velocity; it is a coherent derived unit which quantity is measured in m/s (m/s or m/s1) in the SI (metric system).
To know more velocity visit :
brainly.com/question/18084516
#SPJ4
In the figure, G1 is represented by which numbered part(s) of the cycle?
According to the figure, G1 is represented by parts 4, 5, and 6 numbered part(s) of the cycle.
What is numbered part?
Numbered parts are individual parts of a larger item that are identified by a unique numerical identifier. This number can be used to easily locate and identify the part within the larger item. Numbered parts are often used in complex systems, such as machines, tools, vehicles, and buildings, where multiple components must be located and identified quickly and accurately. For example, a car engine may have hundreds of different numbered parts, each with its own unique identifier. Numbered parts also make it easier for manufacturers to track and inventory the parts used in their products. This helps them to ensure that the right parts are in place and available when they are needed.
To learn more about numbered part
https://brainly.com/question/11250014
#SPJ4
Why is possessing an ASE certification important to one's future as a technician?
Select one:
O a. Leads to better employment opportunities
O b. Allows the technician to transport raw materials to factories
O C.
Technicians gain firsthand experience in communicating effectively with customers in
person
O d. Leads to apprenticeship opportunities
Note that possessing an ASE Certification is crucial because; " Leads to better employment opportunities." (Option D)
What is an ASE Certification?ASE certification, commonly known as Automobile Service Excellence, is given to an automotive mechanic who has finished the necessary training and acquired their Automotive Service Excellence Certified Master Technicians criteria.
There are 58 ASE certification examinations available, covering nearly every facet of the automobile repair and service sector.
The National Institute for Automotive Service Excellence (ASE) offers four levels of certification. They are:
ASE entry-level certification, Professional technician certification, Master technician certification, and ASE advanced level specialist certification.Learn more about ASE Certification:
https://brainly.com/question/28436848
#SPJ1
. There are given three numbers: A, B and C. Even if one of them equal 5 output TRUE, othewise output FALSE.
This can be achieved through a variety of programming languages, here's an example using Python:
A = 4
B = 5
C = 6
if A == 5 or B == 5 or C == 5:
print("TRUE")
else:
print("FALSE")
What is a programming language?A formal language with many instructions is referred to as a programming language. These guidelines are presented to find different outputs. Computer programs are the main use of programming languages. A set of guidelines are presented to ensure the computer's proper operation.
Programming languages are used to control the external devices. In this example, the code checks if any of the variables A, B, or C is equal to 5. If any of them are, the code will output "TRUE", otherwise it will output "FALSE".
Learn more about programming on:
https://brainly.com/question/16936315
#SPJ1
What happens to the generated voltage, if a more powerful magnet is used?
1) The generated voltage gets higher
2) the generated voltage gets lower
3) the amount of voltage generated stay the same
Ethernet standard 1000BASE-SX uses SMF and has a distance limitation of 5km. What is the bandwidth capacity of 1000BASE-SX?
Question 2 options:
A)
10Mbps
B)
100Mbps
C)
1Gbps
D)
100Gbps
E)
1000Gbps
Answer:C
Explanation:
A beam has the extruded cross section shown below, where t-20 mm. 5t 2t t'2t % Matlab input: t-20; Mz-1793; Find y, i.e., the signed distance from the z'-axis to the z-axis, where z is the centroidal axis of the cross section. Determine the moment of inertia I with respect to the centroidal axis z. 6 x10° mm'4 Determine the absolute value of the maximum tensile normal stress σ when the cross-section is subject to the moment M2- 1793 N. m MPa
The spreadsheet listing the pairwise distances in miles between the top 100 US cities by population may be found in the attached Distances.xlsx file.
Below is a screenshot of the spreadsheet. The city names are formatted as follows in the first row and first column: Nashville, TN is an example of a city name, comma, and capitalized state abbreviation. Keep in mind that the spreadsheet's first cell, A1, is empty. Create the get distance function, which takes two character vector inputs representing the names of two cities, as its only parameter. As an output argument called distance, the function returns the separation in between them. Get distance("Seattle, WA","Miami, FL"), for instance, should return 3723. The function returns -1 if one or both of the provided cities are not found in the file.
Learn more about function here-
https://brainly.com/question/17216645
#SPJ4
how to make hypertension thermo fisher with thermal nuclear propulsion powered by 100 thermal nuclear reactor
Hypertension therapy and thermal nuclear propulsion are two distinct fields and they are not related. Hypertension therapy refers to the treatment and management of high blood pressure, while thermal nuclear propulsion refers to the use of nuclear energy to power vehicles, such as spacecraft.
What is the reactor about?Thermal nuclear propulsion technology is still under development and is not yet available for commercial use. Building a thermal nuclear propulsion system would require significant resources, including the development of a suitable reactor and the design and construction of a spacecraft capable of withstanding the intense heat and radiation generated by the reactor.
It would also require compliance with a wide range of safety, environmental and regulatory standards.
Therefore, As for hypertension therapy, it is typically managed through a combination of lifestyle changes, such as diet and exercise, and medication. The specific treatment plan will depend on the individual patient's blood pressure level, overall health, and any other health conditions they may have. It is important to consult a doctor or healthcare professional for personalized treatment recommendations.
Learn more about thermal nuclear reactor from
https://brainly.com/question/2240073
#SPJ1
customer instructions are key to a perfect delivery. true or false
It is true that following client instructions is essential for a flawless delivery. We need 8–15 seconds for eye-lead to use REPS and Checks to remove distractions.
For the first query, "Delivery," the topic is how to satisfy clients by delivering what they have requested. Therefore, by according to the customer's instructions, we can accomplish a flawless delivery.
For the second question, REPS and check means identifying the risks, removing them, making plans, and looking for space. It also means checking for yourself, the risks, the space, and the speed.
To prevent accidents while driving, the REPS and check procedure is employed as a safety measurement. The eye-lead varies depending on the route followed, but it typically lasts between 8 and 15 seconds.
Learn more about REPS here:
https://brainly.com/question/29749274
#SPJ4
bernoulli equation cannot be applied when the flow is
1) Rotational
2) steady
Note that the Bernoulli equation cannot be applied when the flow is "Rotational" (Option 1)
What is the Bernoulli equation?Bernoulli's equation formula represents a relationship between a fluid's pressure, kinetic energy, and gravitational potential energy in a container.
The Bernoulli equation assumes that the fluid flow is irrotational, meaning there is no net fluid flow around a closed loop. Rotational flow, also known as turbulent flow, is characterized by eddies and vortices and cannot be described using the Bernoulli equation.
Learn more about the Bernoulli equation:
https://brainly.com/question/6047214
#SPJ1
During a construction project, engineers used explosives to excavate 140 feet of tunnel into a mountain. But because of time constraints and environmental concerns, they brought in a tunnel boring machine (tbm) to excavate the rest of the tunnel. The data table lists some observations an engineer made about the length of the tunnel after the tbm was introduced. How much of the tunnel was completed 26 days after the tbm was introduced?.
The engineer observed that the tunnel was 460 feet long 26 days after the tbm was introduced. Therefore, the tunnel was completed 460 feet - 140 feet = 320 feet after the tbm was introduced.
What is tunnel?
A tunnel is an underground or underwater passageway, typically constructed for transportation purposes. Tunnels are typically used to bypass obstacles such as mountains, rivers, or bodies of water, or to provide a secure route for transportation of goods and people. Tunnels may also be used for mining, research, or military purposes. Tunnels can be constructed using a variety of materials, including steel, reinforced concrete, rock, earth and soil. The length of a tunnel varies from a few metres to several kilometres. When constructing a tunnel, safety is of paramount importance. Special engineering techniques are used to ensure the stability of the tunnel and its construction is closely monitored and regulated. Tunnels are designed to be resistant to weather, vibration, fire, and other environmental factors.
To learn more about tunnel
https://brainly.com/question/29050301
#SPJ4
A burn-off tet wa performed to determine the volume fraction of
contituent in a gla-fiber-reinforced epoxy compoite. The following
obervation were made:
Weight of empty crucible = 47. 6504 g
Weight of crucible and a mall piece of compoite = 50. 1817 g
Weight of crucible and gla after the burn-off = 49. 4476 g
Calculate the weight and volume fraction of gla fiber and epoxy
rein. Aume that the denitie of the fiber and rein are 2. 5 and 1. 2
gl cm3, repectively
Volume fraction=1.175.
Explanation:
Given:
Weight of empty crucible=47. 6504 g.
Weight of crucible and piece of composite= 50. 1817 g
Weight of crucible and glass after burn-off = 49. 4476 g
weight and volume fraction of glass fiber and
epoxy resin= w glass/w resin
w resin=50. 1817 g- 49. 4476 g = 0.7341 g
w glass=49. 4476 g-47. 6504 g = 1.7972 g
w fraction=1.7972 g/0.7341 g=2.448
Now,
volume of glass fiber=1.7972 g/2.5g/cm^ 3
=0.7188 cm^ 3
volume of epoxy resin=0.7341 g/1.29/cm^ 3
=0.61175 cm^ 3
Volume fraction=v glass/v epoxy resin=0.7188/0.61175cm^ 3
Volume fraction=1.175.
The volume fraction (percentage by volume) is one way to express the composition of a mixture with a dimensionless quantity; others are the mass fraction (percentage by weight) and mole fraction (percentage by moles)
To learn more about volume fraction
https://brainly.com/question/23477586
#SPJ4
Would you expect the following species in a planar conformation to be aromatic, antiaromatic, or neither?
O antiaromatic O neither aromatic nor antiaromatic O aromatic
The species are arranged in such planar manner. neither antiaromatic nor aromatic
species definition
A species is a unit of biodiversity as well as the fundamental categorization and taxonomic rank of an organism in biology. The biggest collection of creatures in which any two persons of the right sexes or mating types may conceive a fertile child, typically by sexual reproduction, is referred to as a species. A species can also be identified by its karyotype, DNA sequence, anatomy, behaviour, or ecological habitat. In addition, since fossil reproduction cannot be studied, palaeontologists employ the chronospecies idea. There are approx 8 and 8.7 million different species of eukaryotes, based on the most current accurate estimate.
To know more about species
https://brainly.com/question/13259455
#SPJ4