Pls helppppp!!!! It’s important :(

The constant current is 0.0406 A for the  nickel anode in an electrolytic cell decreases in mass by 1.20 g in 35.5 min. the oxidation half-reaction converts nickel atoms to nickel(ii) ions.

In an electrolytic cell, the oxidation half-reaction converts nickel atoms to nickel (II) ions, and the nickel anode in an electrolytic cell decreases in mass by 1.20 g in 35.5 min.

To determine the constant current, we can use Faraday's laws. Faraday's laws were established by Michael Faraday, a British scientist, in the early 19th century. His laws explain how much mass will be lost or gained at an electrode during electrolysis and how much electrical energy is required. Faraday's first law states that the mass of a substance deposited during electrolysis is proportional to the number of electrons that pass through the electrolyte.

The following formula can be used to calculate the constant current:

I = (nF / t) × (m / M)

where, I = Constant Current (in amperes), n = number of moles of electrons transferred, F = Faraday constant (96500 C/mol), t = Time taken, m = mass of substance (in grams), M = Molar mass of the substance (in grams/mol)

The Faraday constant is the amount of charge that must pass through an electrode to deposit or liberate 1 mole of any substance. For nickel, the molar mass is 58.69 g/mol, and the oxidation state is +2, which means that two electrons are lost per nickel atom. Thus, n = 2.

To calculate the current, we must first find the number of moles of nickel atoms lost during electrolysis. The formula for the number of moles is:

n = m / M

n = 1.20 g / 58.69 g/mol

n = 0.0204 mol.

Now we can use the formula above to calculate the current:

I = (nF / t) × (m / M)

I = (2 × 96500 C/mol / 2130 seconds) × (1.20 g / 58.69 g/mol)

I = 0.0406 A

I = 40.6 mA or 0.0406 A.

Therefore, the constant current is 40.6 mA or 0.0406 A.

Read more about current here:

https://brainly.com/question/12815553

#SPJ11

The density of carbon monoxide gas at 20°C and 98 kPa is 1.145 g/L.

The ideal gas law is PV = nRT

where P is the pressure, V is the volume, n is the number of moles of gas, R is the gas constant, and T is the temperature in kelvin.

To find the density of carbon monoxide gas at 20°C and 98 kPa, we can use the ideal gas law to find the number of moles of gas in 1 L of gas at these conditions and then divide the mass of 1 mole of gas by the number of moles to get the density.

First, we need to convert the temperature to kelvin:

20°C + 273.15 = 293.15 K

Rearranging the ideal gas law, we get:

n = PV/RT

We can assume that the volume is 1 L, so:

n = (98 kPa)(1 L) / [(0.0821 L·atm/mol·K)(293.15 K)] = 0.0413 mol

The molar mass of carbon monoxide is 28.01 g/mol, so the mass of 0.0413 mol is:

0.0413 mol x 28.01 g/mol = 1.152 g

Therefore, the density of carbon monoxide gas at 20°C and 98 kPa is:

1.152 g / 1 L = 1.145 g/L

What is density?

Density is a physical property of matter that relates to the amount of mass per unit of volume of a substance. It is typically expressed in units such as grams per cubic centimeter (g/cm³) or kilograms per cubic meter (kg/m³).

To know more about density, visit:

https://brainly.com/question/29775886

#SPJ1

Answer:

To use the Clausius-Clapeyron equation, we need to know two sets of conditions for the substance in question. Let's start with question 1:

Question 1:

Given:

Enthalpy of vaporization, ΔHvap = 35.2 kJ/mol

Vapor pressure at T1 = 1 atm (or 760 torr), T1 = 64.7°C

We want to find: Vapor pressure at T2 = 41.9°C

First, we need to convert temperatures to Kelvin:

T1 = 64.7 + 273.15 = 337.85 K

T2 = 41.9 + 273.15 = 315.05 K

Now we can use the Clausius-Clapeyron equation:

ln(P2/P1) = -ΔHvap/R * (1/T2 - 1/T1)

where P1 and P2 are the vapor pressures at temperatures T1 and T2, respectively, R is the gas constant (8.314 J/mol·K), and ln is the natural logarithm.

Solving for P2, we get:

P2/P1 = e^(-ΔHvap/R * (1/T2 - 1/T1))

P2 = P1 * e^(-ΔHvap/R * (1/T2 - 1/T1))

Substituting the given values, we get:

P2 = 1 atm * e^(-35.2 kJ/mol / (8.314 J/mol·K) * (1/315.05 K - 1/337.85 K))

P2 = 0.496 atm

Rounding to three decimal places, the vapor pressure of methanol at 41.9°C is 0.496 atm.

Answer: 0.496 atm

Question 2:

Given:

Enthalpy of vaporization, ΔHvap = 27.5 kJ/mol

Vapor pressure at T1 = 760 torr, T1 = 34.6°C

We want to find: Vapor pressure at T2 = 0.1°C

Converting temperatures to Kelvin:

T1 = 34.6 + 273.15 = 307.3 K

T2 = 0.1 + 273.15 = 273.25 K

Using the Clausius-Clapeyron equation:

ln(P2/P1) = -ΔHvap/R * (1/T2 - 1/T1)

Solving for P2, we get:

P2/P1 = e^(-ΔHvap/R * (1/T2 - 1/T1))

P2 = P1 * e^(-ΔHvap/R * (1/T2 - 1/T1))

Substituting the given values, we get:

P2 = 760 torr * e^(-27.5 kJ/mol / (8.314 J/mol·K) * (1/273.25 K - 1/307.3 K))

P2 = 7.25 torr

Rounding to one decimal place, the vapor pressure of dimethyl ether at 0.1°C is 7.3 torr.

Answer: 7.3 torr

The concentration of the original unknown protein solution that is  determined to be 0.3624 mg/ml in parts-per-million (ppm) = 362.4 ppm

To find the protein concentration in ppm (parts-per-million), first, we need to convert mg/mL to mg/L since 1 ppm is equal to 1 mg/L. Let's start solving this problem.

The concentration of the original unknown protein solution is given as 0.3624 mg/mL.

Conversion factor: 1 ppm = 1 mg/L.

To convert mg/mL to mg/L, we need to multiply the given concentration by 1000.mg/mL to mg/L conversion

= 0.3624 x 1000= 362.4 mg/L

Now, we need to use the ppm conversion factor to get the protein concentration in ppm.

Protein concentration in ppm = (protein concentration in mg/L/1) x 1 ppm

= (362.4 mg/L / 1) x 1 ppm

= 362.4 ppm

Therefore, the protein concentration is 362.4 ppm (parts-per-million)

Learn more about part per million here: https://brainly.com/question/16877061

#SPJ11

Triacylglycerol is broken down by the enzyme lipase into fatty acids and glycerol. It is released by the pancreas and other digestive organs and is essential to the body's ability to digest and absorb fats.

Lipase is the enzyme that converts triacylglycerol into fatty acids and glycerol. The pancreas and other digestive organs release lipase, which is essential for the breakdown and absorption of fats in the body. Triacylglycerols are a kind of lipid that is frequently present in meals including meat, dairy goods, and oils. The triacylglycerol molecule's fatty acid ester linkages are hydrolyzed by lipase, releasing the molecules' separate fatty acids and glycerol. The body's cells can utilize these smaller parts for energy or store them as fat when they are absorbed into the circulation and delivered there. Other lipids, including phospholipids and cholesterol esters, are also broken down by lipase. and is essential for maintaining proper lipid metabolism and homeostasis in the body.

learn more about Triacylglycerol here:

https://brainly.com/question/29697122

#SPJ4

It is not possible to use Edurus and Maxima potions simultaneously in the Harry Potter world.

According to the books and movies, each potion has a specific purpose and cannot be combined for a stronger effect. Edurus is a healing potion that can mend broken bones and heal other injuries, while Maxima is a spell that amplifies the strength of a spell. Therefore, the two have entirely different functions and cannot be used together.However, in some Harry Potter video games, it may be possible to use these potions together. Still, it is not consistent with the canon of the books and movies. In conclusion, it is not possible to use Edurus and Maxima potions simultaneously in the Harry Potter universe, as they serve two entirely different functions.

For more questions on Edurus

https://brainly.com/question/30766927

#SPJ11

The kinetic energy of one molecule of hydrogen (H2) at 300 K is equal to the product of its mass and the square of its velocity. The mass of one molecule of hydrogen is 2.02 x 10^-23 kg, and the velocity of a molecule of hydrogen at 300 K is 1.93 x 10^3 m/s. Therefore, the kinetic energy of one molecule of hydrogen at 300 K is equal to 2.02 x 10^-23 x (1.93 x 10^3)^2 = 7.4 x 10^-15 J.

To explain this in further detail, kinetic energy is the energy associated with an object in motion. It is calculated by the formula KE = 1/2 mv^2. For an object of mass m and velocity v, the kinetic energy is equal to one half of the product of its mass and the square of its velocity. Therefore, the kinetic energy of an object is directly proportional to the square of its velocity.

In the case of a molecule of hydrogen (H2) at 300 K, its mass is 2.02 x 10^-23 kg and its velocity is 1.93 x 10^3 m/s. Therefore, the kinetic energy of one molecule of hydrogen at 300 K is equal to 2.02 x 10^-23 x (1.93 x 10^3)^2 = 7.4 x 10^-15 J.

Know more about kinetic energy here:

https://brainly.com/question/26472013

#SPJ11

A chemical substance or natural product known as a lead compound has biological action against a pharmacological target.

A critical phase of the drug discovery program is lead identification and optimization.

There are two main oxidation states for compounds containing lead: +2 and +4. The first is more typical. Strong oxidants or only occurring in extremely acidic conditions are typical characteristics of inorganic lead(IV) compounds.

The percent yield equation is:

percent yield = actual yield/theoretical yield x 100%

The ratio of the actual yield to the theoretical yield multiplied by 100 is the percent yield.

Characterizing natural products, using combinatorial chemistry, or using molecular modeling as in rational drug design are methods for finding lead compounds. Lead compounds can also be made from substances that high-throughput screening identified as hits.

To know about yield

https://brainly.com/question/2506978

#SPJ4

To determine which area you should settle in after completing your degree, you should consider the average concentrations of Radon-222 in each of the areas you are considering. Radon-222 is a naturally occurring, radioactive gas that is released from the ground and can have a large impact on human health if present in high enough concentrations. Generally, the highest average concentrations of Radon-222 in the United States are found in the Appalachian region, especially in the states of Pennsylvania, West Virginia, Maryland, and parts of Virginia and New York. Therefore, settling in one of these areas would expose you to the highest concentrations of Radon-222.

As per the given statement, "You've been considering what part of the United States to settle in after you complete your degree. You just learned about radon-222.

Which of these areas you are considering would expose you to the highest concentration?

"If someone is thinking of settling in the United States after completing their studies and is concerned about exposure to radon-222, the area that would expose them to the highest concentration would be the area with the most uranium-rich soil.

What is radon-222?

Radon-222 is a radioactive gas that is colorless, tasteless, and odorless. Radon-222 is one of the primary decay products of radium-226, which is formed by the decay of uranium-238. Radon-222, in turn, decays to form polonium-218 and other radioactive particles that can damage lung tissue. Therefore, the area with the most uranium-rich soil would expose an individual to the highest concentration of radon-222.

For more details follow this link: https://brainly.com/question/20527349

#SPJ11

Answer:

The valency of an element refers to the number of electrons an atom can gain, lose or share to attain a stable configuration.

Aluminum (Al) is a metal with an atomic number of 13, which means it has 13 electrons in its neutral state. In its outermost shell, aluminum has three valence electrons.

To attain a stable electronic configuration, aluminum can lose these three valence electrons to become a cation with a 3+ charge (Al3+). By losing these electrons, the outermost shell of the aluminum atom becomes completely filled with eight electrons, which is a stable configuration.

Therefore, the valency of aluminum is 3 because it can lose three electrons to form a stable cation with a 3+ charge.

Explanation:

Answer:

The valency of an element refers to the number of electrons an atom can gain, lose or share to attain a stable configuration.

Aluminum (Al) is a metal with an atomic number of 13, which means it has 13 electrons in its neutral state. In its outermost shell, aluminum has three valence electrons.

To attain a stable electronic configuration, aluminum can lose these three valence electrons to become a cation with a 3+ charge (Al3+). By losing these electrons, the outermost shell of the aluminum atom becomes completely filled with eight electrons, which is a stable configuration.

Therefore, the valency of aluminum is 3 because it can lose three electrons to form a stable cation with a 3+ charge.

Explanation:

The pressure when the gas is pumped into a 5.00 L vessel that was initially enclosed in a 10.0 L tank at 1200 mm Hg pressure, as found by Boyle's Law is 2400mm Hg.

The ideal gas law Boyle's Law can be used to solve the problem.

Boyle's Law states that the pressure and volume of a gas are inversely proportional to each other, with all other parameters remaining constant. It can be represented as:

P₁V1 =P₂V2

Where, P₁ = initial pressure, V1 = initial volume, P₂ = final pressure, V2 = final volume.

The amount of gas and temperature remains constant.

Initially, the gas is enclosed in a 10.0 L tank at 1200 mm Hg pressure.

Let's call it Tank1.

V1 = 10.0 L, P₁= 1200 mm Hg

For Tank2,

P₂ = ?, V2 = 5.00 L

Substitute the given values in the ideal gas law

P₁V1 = P₂V2

⇒ 1200 mm Hg × 10.0 L = P₂ × 5.00 L

⇒ 12000 = 5.00 x P₂

⇒ P₂ = 12000/5.00 mm Hg

⇒ P₂ = 2400 mm Hg

Therefore, the reasonable value for the pressure when the gas is pumped into a 5.00 L vessel is 2400 mm Hg.

To know more about Boyle's Law, refer here:

https://brainly.com/question/1437490#

#SPJ11

The volume of a gas is increased from 0.5L to 4.0 L while the temperature is held constant. The pressure of the gas decreases by a factor of eight.

Charles's Law- Charles's Law is a physical law that states that for a fixed mass of gas held at a constant pressure, the volume of the gas is directly proportional to the absolute temperature of the gas.

V1/T1=V2/T2 (Constant Pressure)

Boyle's Law- Boyle's law is a gas law that states that the pressure applied to a gas at a constant temperature is inversely proportional to the volume of the gas.

P1V1 = P2V2 (Constant Temperature)

What is the ideal gas law? The ideal gas law is a physical law that describes the behavior of an ideal gas in terms of its pressure, volume, temperature, and the number of particles present.

PV = nRT

Where: P = pressure, V = volumen = number of particles present, R = ideal gas constant, T = absolute temperature

What happens to the pressure of the gas when the volume of the gas is increased? The pressure of the gas decreases when the volume of the gas is increased while holding the temperature constant. Therefore, when the volume of the gas increases from 0.5L to 4.0 L while the temperature is held constant, the pressure of the gas decreases.

The correct answer is B. decreases by a factor of eight.

To learn more about "volume of a gas", visit: https://brainly.com/question/27100414

#SPJ11

The chemical equation for HF (aq) showing how it is an acid according to the Arrhenius definition is [tex]HF(aq) + H_2O(l)[/tex] ⇒ [tex]H_3O^+(aq) + F^-(aq)[/tex].

In this equation, HF is a weak acid that partially ionizes when dissolved in water, and the [tex]H_2O[/tex] acts as a base.

The reaction produces the hydronium ion [tex]H_3O^+[/tex]and the fluoride ion [tex]F^-[/tex]which are responsible for the acidic properties of the solution.

The phases in this equation are aqueous (aq) for HF,  [tex]H_3O^+[/tex] and [tex]F^-[/tex], and liquid (l) for water.

Hence , [tex]HF(aq) + H_2O(l)[/tex] ⇒ [tex]H_3O^+(aq) + F^-(aq)[/tex] is a chemical equation for HF.  The reaction shows that when HF is dissolved in water, it gives [tex]H3O^+[/tex]and [tex]F^-[/tex]ions. The[tex]H3O^+[/tex] ion is the hydrated hydrogen ion or the hydronium ion, and [tex]F^-[/tex]is the fluoride ion.

Thus, the given chemical equation represents the Arrhenius acid-base reaction of HF.

To know more about Acid refer here :

https://brainly.com/question/25148363

#SPJ11

The names of the given compounds are:

a) Carbon tetrachloride

b) 1-chloro-2-chloromethane (also known as chloroethyl chloride)

c) 1,2-dichloroethane

d) 2-chloro-2-methylbutane

e) 1,4-dichlorobutane

A compound is a substance made up of two or more different elements chemically combined in fixed proportions. The elements in a compound are held together by chemical bonds, which are formed when atoms of different elements share or transfer electrons to achieve a stable electron configuration.

Compounds have unique properties that are different from their constituent elements, such as melting point, boiling point, density, and reactivity. They can be formed through various chemical reactions, such as synthesis, decomposition, combustion, and oxidation. Examples of common compounds include water (H2O), table salt (NaCl), carbon dioxide (CO2), and glucose (C6H12O6).

Learn more about chemical compounds here https://brainly.com/question/29594386

#SPJ1

1) If you reduce the substrate concentration by 50%, the Vmax of the enzyme will decrease proportionally.ii) When the substrate concentration is lowered, fewer substrates will bind to the enzyme, resulting in a lower rate of product formation. As a result, the enzyme's maximum velocity (Vmax) will decrease, and the reaction's rate will slow. As a result, the kinetic parameters of the enzyme, including Vmax and Km, will change.

2) The Vmax of an enzyme is the maximum rate of the reaction that can be achieved by the enzyme when it is saturated with a substrate. A decrease in the substrate concentration means that the enzyme's active sites are less likely to be filled with substrates, and the maximum rate of the reaction that can be achieved by the enzyme decreases in proportion.

As the substrate concentration is lowered, the enzyme's Vmax decreases. The enzyme-substrate complex's kinetics are influenced by the substrate concentration. The Michaelis-Menten equation is used to describe the relationship between the substrate concentration and the reaction rate. The Km value and the Vmax value are two constants in the Michaelis-Menten equation.

Know more about Michaelis-Menten here:

https://brainly.com/question/30756012

#SPJ11

The value of Kp for the reaction with equilibrium pressure of A is given as PA = 0.20 atm and the initial pressure of A is 0.0190.

To find the value of Kp for the reaction, we will use the expression for the equilibrium constant in terms of the partial pressures of the reactants and the products.

Kp = (PB)²/PA

where, PB is the equilibrium pressure of B.

Initially, there is no B in the reaction vessel, so the change in pressure of B is equal to its equilibrium pressure. Using the law of conservation of mass, we can write:

PV = nRT

where, P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature.

Since there is no change in volume or temperature, we can write:

PV = constant or P₁V₁ = P₂V₂

where, P₁ and P₂ are the initial and equilibrium pressures of A, respectively. Since A is the only gas initially present in the reaction vessel, we can write:

P₁ = PA = 1.19 atm, P₂ = 0.20 atm V₁ = V₂

Therefore, P₁V₁ = P₂V₂ = PAV₁ = PBV₂

Since, the number of moles of A and B are related by the balanced chemical equation, we can write:

2(PB) = nB

Substituting, PB in terms of PA and V1, we get:

Kp = (PB)²/PA = (nB/2V₂)²/PA

Kp= (nB/2PAV₁)²/PA= (nB)²/(4P²AV₁)

where, nB is the number of moles of B.

To find the number of moles of B, we use the balanced chemical equation. 2 moles of B are produced for every mole of A that reacts. Since, the initial pressure of A was 1.19 atm and the equilibrium pressure of A was 0.20 atm, 0.99 atm of A has reacted.

Therefore, the number of moles of A that has reacted is:

nB = (0.99/1.19) = 0.8327 mol

The total number of moles of the system is the sum of the moles of A and B initially present in the reaction vessel.

nTotal = nA + nB

Initially, only A is present, so nTotal = nA = 1 mol. The number of moles of B is therefore:

nB = nTotal - nA = 1 - 0.8327 = 0.1673 mol

Substituting the values of PA, nB, and V1, we get:

Kp = (nB)²/(4P²AV1) = (0.1673)²/(4 × 1.19² × 1) = 0.0190

Therefore, the value of Kp for the reaction is 0.0190.

Learn more about Kp here:

https://brainly.com/question/30550192

#SPJ11

The correct answer is that the recrystallization is a common technique used to purify solid compounds in organic chemistry.

The following are some of the lab techniques that may be utilized in a recrystallization experiment: Dissolving the impure compound in a suitable solvent. Filtering the solution to remove insoluble impurities. Heating the solution to dissolve the compound completely. Allowing the solution to cool slowly to allow the compound to crystallize out. Filtering the crystallized product using a Buchner funnel or filter paper. Washing the product with a suitable solvent to remove any remaining impurities. Drying the product using a desiccator or oven. Other techniques that may be used in conjunction with recrystallization include melting point determination, thin-layer chromatography, and spectroscopic analysis to confirm the purity and identity of the compound.

To learn more about recrystallization click the link below

brainly.com/question/29215760

#SPJ4

The structural feature that distinguishes whether a hydrocarbon is an alkane, alkene, alkyne, or aromatic is the type of carbon-carbon bonding present in the molecule.

(a) Alkanes have single covalent bonds between all carbon atoms in the molecule. Ethane (C2H6). (b) Alkenes have at least one double covalent bond between two carbon atoms in the molecule. Example: Ethene (C2H4). (c) Alkynes have at least one triple covalent bond between two carbon atoms in the molecule. Example: Ethyne (C2H2). (d) Aromatic hydrocarbons have a cyclic structure with alternating double bonds that form a delocalized pi electron system known as an aromatic ring. Example: Benzene (C6H6).

To know more about carbon-carbon bonding, here

brainly.com/question/12156863

#SPJ4

The breakdown of 6.54 g of potassium chlorate results in the production of 4.81 x [tex]10^{22}[/tex]oxygen molecules.

The balanced chemical equation for the decomposition of potassium chlorate is:

2 KClO3(s) → 2 KCl(s) + 3 O2(g)

This equation tells us that for every 2 moles of potassium chlorate that decompose, 3 moles of oxygen gas are produced.

To determine the number of molecules of oxygen produced by the decomposition of 6.54 g of potassium chlorate, we first need to convert the mass of potassium chlorate to moles using its molar mass. The molar mass of KCLO₃ is:

K: 39.10 g/mol

Cl: 35.45 g/mol

O: 3(16.00 g/mol) = 48.00 g/mol

Total molar mass of KCLO₃: 39.10 + 3(35.45) + 48.00 = 122.55 g/mol

Number of moles of KCLO₃ = 6.54 g / 122.55 g/mol = 0.0533 mol

Now we can use the mole ratio from the balanced equation to calculate the number of moles of oxygen produced:

3 moles O₂ / 2 moles KCLO₃ = x moles O₂ / 0.0533 moles KCLO₃

x = 3/2 x 0.0533 = 0.0799 moles O₂

Finally, we can convert the number of moles of oxygen to the number of molecules using Avogadro's number:

Number of molecules of O2 = 0.0799 mol x 6.022 x [tex]10^{23}[/tex] molecules/mol = 4.81 x [tex]10^{22}[/tex] molecules

Therefore, 4.81 x [tex]10^{22}[/tex] molecules of oxygen are produced by the decomposition of 6.54 g of potassium chlorate.

To learn more about  molecules  refer to:

brainly.com/question/14646440

#SPJ4

If the strength of magnet 1 is weaker than the strength of magnet 2, then the overall kinetic energy in the system would increase. This is because the weaker magnet would exert less force on the magnetic object, causing it to accelerate more and gain more kinetic energy as it approaches the stronger magnet.

In the above scenario, the magnetic force between two magnets causes a magnetic object to accelerate, which in turn creates kinetic energy.

When the magnetic object is placed between the two magnets, the stronger magnet exerts a stronger magnetic force on the object, causing it to accelerate towards the stronger magnet.

At the same time, the weaker magnet also exerts a magnetic force on the object, albeit a weaker one. As a result, the object experiences a net force towards the stronger magnet, which causes it to accelerate and gain kinetic energy as it moves closer to the magnet with higher magnetic strength.

Learn more about Magnet on:

https://brainly.com/question/2841288

#SPJ1

Saddam Hussein's overthrow in 2003 was one of the early results of regime transition in Iraq. Given that Hussein had been in charge of Iraq's government and society for more than 20 years,

this represented a dramatic change in the political landscape of the nation. Regime transition, however, was followed by a turbulent era of political unrest and sectarian warfare. Broader geopolitical repercussions of the US-led invasion of Iraq and subsequent government change included strained ties with other nations in the region, a rise in anti-American sentiment, and the creation of new extremist organizations like ISIS. The long-term implications of the Iraqi government transition are still being discussed and examined, although is clear that the initial outcome was one of significant.

learn more about Iraq  here:

https://brainly.com/question/29605758

#SPJ4

If yellow bromthymol blue is present, the solution is acidic. In an acidic solution, phenolphthalein, an acid-base indicator, is colourless; nevertheless, as the solution becomes alkaline, it turns pink or red.

An indicator, such as phenolphthalein, changes colour when it comes into contact with an acid or a basic. If it comes into contact with an acid like vinegar or a neutral substance like water, it remains colourless; if it comes into contact with something basic like ammonia, it turns purple.

The acid bromthymol blue is weak. Depending on the pH of the solution, it may take the form of an acid or a basic. This reagent turns blue in basic solutions and yellow in acidic solutions.

To know more about indicator visit:-

brainly.com/question/29016702

#SPJ1

Mono addition of HBr to conjugated dienes leads to multiple products, and a given addition product can arise from more than one conjugated diene. The pair of dienes which can serve as precursors for both of the addition products are diene 1 and diene 2. Diene 1 can give rise to the allylic bromide product A as well as product B.

Diene 2 can give rise to the allylic bromide product C as well as product B.
The other three dienes cannot give rise to either of the two given allylic bromide products.
The given pairs of dienes are:
(a) H2C=CHCH=CH2 and H2C=CHCH2CH=CH2
(b) H2C=CHCH=CH2 and H2C=CHCH=CHCH3
(c) H2C=CHCH=CHCH3 and H2C=CHCH2CH=CH2
(d) H2C=CHCH=CHCH3 and H2C=CH2CH=CHCH3
(e) H2C=CHCH=CHCH3 and H2C=CH=CHCH2CH3 The given allylic bromide products are 1,2-dibromobutane and 2-bromo-2-butene respectively. Hence, the correct pair of dienes is (b) H2C=CHCH=CH2 and H2C=CHCH=CHCH3, since both of these dienes can act as precursors for both of the allylic bromide products.

For more such questions on HBr

https://brainly.com/question/12858312

#SPJ11

Adding a catalyst to a chemical system has some certain effects including increased reaction rates, reaction quotient is unaffected.

A catalyst is an element or compound that speeds up the rate of a chemical reaction by lowering the activation energy barrier. The catalyst provides an alternative mechanism with a smaller activation energy that is followed by the reactants. As a result, adding a catalyst to a chemical system increases the reaction rate.

The reaction quotient is unaffected: When a catalyst is added to a chemical system, the reaction quotient is not affected because it does not change the composition of the equilibrium mixture. Therefore, adding a catalyst to a chemical system does not have an effect on the reaction quotient.

Therefore, the correct options are A and B.

Learn more about Catalyst here:

https://brainly.com/question/24430084

#SPJ11

CO₂ is nonpolar molecule, CH₄ is a nonpolar molecule, N₂ is a nonpolar molecule, and H₂O is a polar molecule.

Non polar molecules are the molecules which are symmetric with no unshared electrons in the structure. Polar molecules are the asymmetric molecules, which are either containing lone pairs of electrons on a central atom or having atoms with different electronegativities bonded to each other.

The linear CO₂ molecule is polar molecule due to the difference in electronegativity between the Carbon and Oxygen atoms. The tetrahedral CH₄ molecule is nonpolar since all the atoms have the same electronegativities. The linear N₂ molecule is nonpolar since it has a symmetrical linear shape. Finally, the bent H₂O molecule is polar due to the difference in electronegativity between the Hydrogen and Oxygen atoms.

Learn more about Molecules here:

https://brainly.com/question/15173422

#SPJ11

The correct answer is that Sodium hydroxide (NaOH) is a chemical compound that consists of sodium ions (Na+) and hydroxide ions (OH-).

Sodium hydroxide is commonly known as caustic soda and is used in many industrial processes, including paper production, soap making, and water treatment. Since sodium hydroxide is a chemical compound, it is considered a chemical property rather than a physical property. A physical property is a characteristic of a substance that can be observed or measured without changing the identity or composition of the substance, while a chemical property is a characteristic of a substance that describes how it interacts with other substances to form new substances. Sodium hydroxide is highly reactive and can undergo chemical reactions with a variety of other substances. For example, it can react with acids to form salts and water, and with certain metals to produce hydrogen gas. These chemical reactions are a result of the chemical properties of sodium hydroxide and its ability to react with other substances, indicating that it is a chemical property.

To learn more about Sodium hydroxide click the link below

brainly.com/question/18723610

#SPJ4

The [H₃O+] and the pH of a 0.140 M H₃C₆H₅O₇ solution is [H₃O+] = 1.49 ×[tex]10^-3[/tex]M, and pH = -log[H₃O+] = 2.83.

H₃C₆H₅O₇ is a weak acid, so we need to use the acid dissociation constant (Ka) to calculate the [H₃O+] and pH of its solution. The Ka for H₃C₆H₅O₇ is 6.3 × [tex]10^-5.[/tex]

The balanced chemical equation for the dissociation of H₃C₆H₅O₇ in water is:

H₃C₆H₅O₇ + H2O ⇌ H3O+ + H₃C₆H₅O₇-

At equilibrium, let x be the concentration of H₃O+ and H₃C₆H₅O₇-. Then:

Ka = [H₂O+][ H₃C₆H₅O₇-] / [H3C6H5O7]

Ka = [tex]x^2[/tex]/ (0.140 - x)

Assuming that x is much smaller than 0.140, we can simplify this equation to:

[tex]x^2[/tex] = Ka × 0.140

x = √(Ka × 0.140)

x = √(6.3 × [tex]10^-5[/tex]× 0.140)

x = 1.49 × [tex]10^-3[/tex]M

solution is a homogeneous mixture of two or more substances that are uniformly dispersed throughout the mixture. The substance that is present in the largest amount is called the solvent, and the substances that are dissolved in the solvent are called solutes.

Learn more about solution here:

https://brainly.com/question/30665317

#SPJ4

Increasing the substrate concentration will likely result in the greatest increase in the reaction rate when the substrate concentration is lower than the concentration of the enzyme.

The concentration of the substrate affects the rate of reaction since there is a direct correlation between the number of enzyme-substrate complexes that are formed and the rate of reaction.

When there is more substrate, more enzyme-substrate complexes can form, resulting in an increase in the rate of reaction.

So, it is highly likely that when the substrate concentration is low, increasing the substrate concentration will result in the greatest increase in the reaction rate.

However, when the substrate concentration is already high, the reaction rate may not continue to increase as a result of increasing the substrate concentration.

Learn more about substrate concentration here:

https://brainly.com/question/22428921

#SPJ11

The number of moles of nitrogen atoms present in the sample is: 12.86 mol of nitrogen atoms

At STP (Standard Temperature and Pressure), the temperature is 273 K and the pressure is 1 atm. The molar volume of any ideal gas at STP is 22.4 L/mol. Therefore, the number of moles of N204 gas present in the sample can be calculated as:

n = V/VM

where n is the number of moles, V is the volume of the gas, and VM is the molar volume of the gas at STP.

n = 144 L / 22.4 L/mol = 6.43 mol

Since dinitrogen tetroxide contains two nitrogen atoms per molecule, the number of moles of nitrogen atoms present in the sample is:

2 x 6.43 mol = 12.86 mol of nitrogen atoms.

To know more about atoms click here:

brainly.com/question/29695801

#SPJ4

A solution's boiling point rises as the amount of dissolved ions increases because more energy is needed to overcome greater intermolecular interactions that occur between the ions and solvent molecules.

The intermolecular interactions between the molecules of the solute and solvent are impacted when a solute is dissolved in a solvent. When it comes to ionic solutes, the ions separate and create ion-dipole interactions with the solvent molecules. In non-ionic solutions, these interactions are more potent than the dipole-dipole and London dispersion forces. Because the intermolecular interactions in a solution with more dissolved ions are stronger, more energy is needed to overcome them and reach the boiling point. The van 't Hoff factor, which measures the amount of ions created by each solute molecule, and the molality of the solution are used to quantify the boiling point elevation impact.

learn more about boiling point here:

https://brainly.com/question/25777663

#SPJ4