One principle of this course states, "Communication cannot be reversed." Explain this statement in your own words AND provide at least one personal example when you wished you could "un-send" a message.

Answer: Acceleration, a= -1.11*10^-5

Explanation:

Using a= (V(final speed)- U(Initial speed) )/ TIME IN SECONDS

5hr to seconds is 5*60*60=18,000s

(2.8m/s-3m/s)/ 18,000s = -1.11*10^-5

I'm sorry I wasn't able to explain well, but I hope this helps.  

The correct answer of the angular speed and linear speed respectively is option A) 0.1047,0.01047

To find the angular speed of the second hand of a clock, we use the formula:

Angular speed = 2π / time

Since the second hand of a clock completes one full rotation every 60 seconds, the time is 60 seconds. Therefore:

Angular speed = 2π / 60

Angular speed = 0.1047 rad/s

To find the linear speed of the tip of the second hand, we use the formula:

Linear speed = angular speed x radius (v = ωr)

Since the radius of the second hand is 10cm or 0.1m, we can plug in the values:

Linear speed = 0.1047 x 0.1

Linear speed = 0.01047 m/s

Therefore, the angular speed of the second hand of a clock is 0.1047 rad/s and the linear speed of its tip is 0.01047 m/s.

The correct answer to the angular speed and linear speed is therefore option A) 0.1047, 0.01047.

To know more about angular speed, refer here:

https://brainly.com/question/9684874#

#SPJ11

The stated statement indicates that Scales less than 1:24,000 are 1:900,000 and 1:24,000, respectively.

The correct option is B.

a graded object, particularly when used as a rule or measure: a set of markings or points spaced apart at defined intervals used to measure distances, such as: a relationship between the distances shown on a map and their corresponding actual distances (such as the height of the mercury in a thermometer)

To visually depict the scale of a map, maritime chart, engineering design, or architectural drawing, use a linear scale, also known as a bar scale, scale bar, or graphic scale.

To know more about scale visit:

https://brainly.com/question/1287267

#SPJ4

Yes, it is true, the longer a pendulum is, the longer it takes to swing. Therefore, when the pendulum of a clock is lengthened, the clock slows down.

The length of a pendulum influences the time it takes to complete one swing, which is referred to as the period. The pendulum swings more slowly and has a longer period as it gets longer. A clock slows down when the pendulum is stretched because it takes longer for each swing to be completed. Similar to how the clock speeds up when the pendulum is shorter, it swings quicker as well. The operation of pendulum clocks and other timekeeping instruments that employ pendulums to measure time is based on this idea.

A pendulum's period, or how long it takes to complete one full swing back and forth, can be used to define how it moves. The length, gravitational acceleration, and angle of displacement are some of the variables that affect a pendulum's period. However, the length of a particular pendulum is what essentially determines its period.

The period of a basic pendulum is described mathematically as

T = 2(L/g), where T is the period, L is the length of the pendulum, and g is the gravitational acceleration.

As you can see, the square root of the length and the period are precisely proportional. This implies that the period likewise grows as the pendulum's length does.

The pendulum offers a means of controlling the clock's timekeeping mechanism. The clock's hands are moved by a gear train that is moved back and forth by the pendulum. The pendulum's length can be changed by the clockmaker to alter the clock's rate of movement. The pendulum can be shortened to make it swing more quickly and speed up the clock if it is running quickly. The pendulum can be stretched to make it swing more slowly and slow down the clock if it is operating slowly.

For more question on pendulum click on

https://brainly.com/question/26524032

#SPJ4

The sun is not located at the center of an elliptical orbit, but is offset somewhat toward one of its ends - True.

The Sun is not relatively at the center of a earth's elliptical route. An cirque has a point a little bit down from the center called the" focus". The Sun is at the focus of the cirque. Because the Sun is at the focus, not the center, of the cirque, the earth moves near to and further down from the Sun every route. The close point in each route is called perihelion. The far down point is called aphelion.

The Sun isn't located at the center of an elliptical route, but is neutralize kindly toward one of its ends. The Greek champion Claudius Ptolemaeus ( Ptolemy) tutored that all heavenly bodies moved in perfect indirect routeways centered on the Earth.

Learn more about Sun's Elliptical orbit:

https://brainly.com/question/15656021

#SPJ4

The required velocity and acceleration of this particle when position of the particle is given are never zero. Correct option is D.

The position of the particle is given as x = 3t³ - 6t, y = t² - 2t

The particle's velocity is determined by,

v = dx/dt i + dy/dt j = (9t² - 6) i +  (2t - 2) j

The velocity at the point t = 0 is,

v = (9t² - 6) i +  (2t - 2) j = - 6 i - 2 j

The velocity at the point t = 1 is,

v = (9t² - 6) i +  (2t - 2) j = 3 i

The acceleration of the particle is,

a = d²x/dt² i + d²y/dt² j = 18t i + 2 j

The particle's acceleration at time zero is,

a = 2 j

Thus, the velocity and acceleration of this particle are never zero.

To know more about velocity:

https://brainly.com/question/11264478

#SPJ4

To answer the question: "A student made a model of isostasy by placing a block of wood in a beaker of water how can a student demonstrate isostaic rebound using her model?" If she "Press the block down and let go

The state of gravitational equilibrium between the Earth's crust and mantle known as isostasy or isostatic equilibrium causes the crust to "float" at an elevation that is dependent on its thickness and density.

This idea is used to explain how various topographic heights can occur on the surface of the Earth.

Hence, to test the model she has, she should press the block down and let go

Read more about isostasy here:

https://brainly.com/question/4347729

#SPJ1

A student made a model of isostasy by placing a block of wood in a beaker of water how can a student demonstarte isostaic rebound using her model

A. Blow vigorously on the block

B. Press the block down and let go

C. Add water until the beaker overflow

D. Pour out all the water

The horizontal component of acceleration is always zero is the quantities are zero throughout the flight.

What is acceleration?

Acceleration was the representation rate In a change of velocity because the acceleration always depends on the object's speed. Acceleration determines the rate of the particles. Acceleration is the vector quantity. It is a vector quantity, but it has both extent and movement. Newton's law also has the acceleration of the magnitude described. The m.s-2 is the standard unit for acceleration.

What is velocity ?

The most important metric for determining an object's position and rate of movement is its velocity. The distance that an object travels in a certain amount of time might be used to define it. The object's displacement in a unit of time is referred to as velocity.

Therefore, The horizontal component of acceleration is always zero is the quantities are zero throughout the flight.

Learn more about acceleration from the given link.

https://brainly.com/question/460763

#SPJ1

The equation gives the capacitance of a parallel-plate capacitor:C = εA/d. Where C is the capacitance, ε is the permittivity of the dielectric material between the plates, A is the area of each plate, and d is the distance between the plates.

In this case, the area of each plate is 10 cm × 20 cm = 200 cm^2 = 0.02 m^2. The distance between the plates is 2.0 mm = 0.002 m. The permittivity of the dielectric material is ε = ε0εr, where ε0 is the vacuum permittivity (8.85 × 10^-12 F/m), and εr is the relative permittivity or dielectric constant (4.1).

So, substituting these values into the equation, we get:

C = εA/d

= (ε0εr)(0.02)/(0.002)

= (8.85 × 10^-12)(4.1)(0.02)/(0.002)

= 7.26 × 10^-11 F

= 72.6 pF

Therefore, the capacitance parallel-plate capacitor is 72.6 pF.

To learn more about parallel-plate capacitor, visit here

https://brainly.com/question/12733413

#SPJ4

Equation to solve for v:v = sqrt(u² + 2as)Substituting the given values, we get:v = sqrt((25.7 m/s)² + 2(-9.8 m/s²)(16.1 m))v = 14.9 m/s

It is a scalar quantity that represents the speed at which an item moves or changes position with respect to time.

A) To determine the initial velocity required to clear the river and land safely on the other side, we need to use the following equation d = vt + (1/2)at²

Where d is the distance the car needs to travel horizontally, which is the width of the river (68 m).v is the initial velocity of the car. An is the acceleration due to gravity (-9.8 m/s²).

T is the time the car spends in the air. We can rearrange this equation to solve for v:v = (d – (1/2)at²) / substituting the given values, we get:v = (68 m – (1/2)(-9.8 m/s²)(18.1 m)²) / (2(18.1 m)/v)v = 25.7 m/s

B) To determine the speed of the car just before it lands on the other side, we can use the following equation: where:u is the initial velocity of the car. An is the acceleration due to gravity (-9.8 m/s²).s  [tex]v^² = u^² + 2as[/tex]is the vertical distance the car travels from the cliff to the other side (18.1 m – 2 m = 16.1 m).

Therefore, (A) To clear the river and safely land on the other side, the car must be moving at a speed of 25.7 m/s (or approximately 92.5 km/h) immediately as it exits the cliff.

(B) The car is travelling at a speed of 14.9 m/s, or approximately 53.6 km/h, shortly before it safely falls on the opposite side.

Learn more about speed here:

https://brainly.com/question/23377525

#SPJ4

A car comes to a bridge during a storm and finds the bridge washed out. The driver must get to the other side, so he decides to try leaping it with his car. The side the car is on is 18.1 m above the river, whereas the opposite side is a mere 2 m above the river. The river itself is a raging torrent 68 m wide.A) How fast should the car be travelling just as it leaves the cliff in order to just clear the river and land safely on the opposite side? B) What is the speed of the car just before it lands safely on the other side?

(a). Elasticity of supply between W and X is elastic.

(a)-1.The supply elasticity relationship Y and Z becomes inelastic.

b. The assertion is accurate.

Like a dishwasher or a car, these are infrequently acquired things that can be put off if the price increases. Elasticity is a crucial economic metric because it shows how much of an item or service consumers consumes when the price varies, which is especially essential for businesses that sell goods or services. That whenever a commodity is elastic, a price fluctuation prompts a shift in demand for it rapidly.

Economists use elasticity to determine how different factors interact. Pricing, cross-price quantity demanded, and quantity demanded are the three main types of elasticity. Goods' elasticity gauges how sensitive they are to price changes.

To know more about elastic visit:

https://brainly.com/question/28192591

#SPJ4

a) The multiplicative factor by which the sound intensity decreases as you go from the first to the second site is 64.

b) The additive amount by which the sound level intensity decreases as you go from the first to the second site is -15.56 dB.

a) The intensity of the sound is measured in decibels and the sound intensity level with the intensity I is calculated by the expression,

β(dB) = 10 log(I/I₀)

where,

β/dB is the intensity level

I is sound intensity

The intensity is given by the relation,

Intensity = Power/Area

I = (P/πr²)

Intensity is inversely related to the square of radius.

I₁/I₂ = (r₂/r₁)² = (8/1)² = 64

I₁ = 64 I₂

So, the multiplicative factor is 64.

b) The formula for the intensity level is given by,

β(dB) = 10 log(I/I₀)

β₁ = 10 dB log(I₁/I₀)

β₂ = 10 dB log(I₂/I₀)

β₂ - β₁ = 10 dB[log(I₂/I₀) - log(I₁/I₀)]

β₂ - β₁ = 10 dB log(I₂/I₁)

β₂ - β₁ = 10 dB log(1/36) = -15.56 dB

To know more about sound:

https://brainly.com/question/20214158

#SPJ4

A collision that is elastic occurs when there is no net loss of kinetic energy in the system as a result of the collision. Kinetic energy and momentum are both conserved in elastic collisions.

When two balls collide at a pool table, that is an instance of an elastic collision. When you throw a ball on the ground and it bounces back into your hand, there is no net change in the kinetic energy, making it an elastic collision.

Two balls colliding at a pool table is an example of an elastic collision. When a ball is tossed to the ground and subsequently returns to your hand, there is no net change in the kinetic energy, making it an elastic collision.

To know more about collision visit:

brainly.com/question/12550364

#SPJ1

The y component of the velocity vector is 10 m/s. Then the v is 12.86 m/s. Now the x component of this velocity is v sin θ.That is , x component is 8 m/s.

Velocity of an object is the measure of its distance travelled per unit time. Velocity is a vector quantity thus having both magnitude and acceleration. The magnitude is called speed.

For a velocity vector there are three translation components possible for three different axes.

here, x component = v sinθ

y component = v cos θ

Given that v cos θ = 10 m/s

θ = 39

Vy = v cos 39 = 10 m/s

then v = 12.8 m/s

Now, the x component is calculated as:

vx = 12.8 m/s sin 39 = 8 m/s.

Therefore, the x component of velocity here is 8 m/s.

Find more on velocity :

https://brainly.com/question/17127206

#SPJ9

The true statement about the motion of the helicopter is " the helicopter travels at a greater speed between D and E than it did between A and B.

option D.

Motion is the process of an object changing its position with respect to a reference point over time. It involves the movement of an object from one point in space to another.

Motion can be described in terms of its speed, direction, and acceleration. Speed refers to the rate at which an object is moving, while direction refers to the path that the object is following. Acceleration refers to the rate at which an object's speed or direction changes.

v = Δx / Δt

where;

The change in position of the helicopter between A and B = 0

because, A = 100 m and B = 100 m

so the speed of the helicopter between A and B = 0 m/s.

Thus, the last statement is the only correct option,

Learn more about motion here: https://brainly.com/question/25951773

#SPJ1

Sally's observation that the water bottle appeared untouched while the acetone bottle was empty can be explained by the stronger cohesive forces between the water molecules compared to the acetone molecules. The water molecules stick together more tightly, preventing them from evaporating as quickly as the acetone molecules

Sally's statement that particles in water stick together more is partially correct. The cohesive forces between the particles in water, also known as hydrogen bonds, are indeed stronger than the intermolecular forces between the particles in acetone, which are dipole-dipole interactions.

The strength of the intermolecular forces between particles is determined by the type of chemical bonding and the molecular structure of the substance. In the case of water, the oxygen atom in each molecule attracts electrons more strongly than the two hydrogen atoms, giving rise to partial negative charges around the oxygen and partial positive charges around the hydrogen. This creates an electrostatic attraction between neighboring water molecules, resulting in hydrogen bonding.

On the other hand, acetone molecules have a polar covalent bond between the carbon and oxygen atoms, resulting in partial positive and negative charges. The intermolecular forces between acetone molecules are weaker than those between water molecules, because the dipole moments in acetone are not as large as the dipole moments in water.

Learn more on hydrogen bonds here https://brainly.com/question/1420470

#SPJ1

The plate is about 12.65 units away from the top of the bowl, with a contact area of 48 square units on the bottom of the bowl.

The plate is parallel to the rim of the bowl, it is not in contact with the curved surface of the bowl. The area of the plate in contact with the bottom of the bowl can be calculated as the product of its dimensions: 6 x 8 = 48 square units.

The distance between the bottom of the bowl and the top of the plate can be calculated using the Pythagorean theorem. The height of the bowl is the radius, which is 13 units. The width of the bowl can be calculated as the diameter, which is twice the radius, or 26 units. The width of the plate is 6 units, so the distance between the bottom of the bowl and the top of the plate can be calculated as,

sqrt(13^2 - 3^2) = sqrt(160) = 12.65 units

To know more about the hemispherical bowl, here

brainly.com/question/13645703

#SPJ4

During Stage 1, the heat equation that governs the temperature distribution T(x, t) in the pan bottom is given by:

ρc_p∂T/∂t = k∂^2T/∂x^2 + q_0/V

The boundary conditions are:

At x = 0 (the surface in contact with the stove), the temperature is fixed at Ti, and there is no heat flux:

T(x=0,t) = Ti, ∂T/∂x = 0

At x = L (the surface in contact with the water), the heat flux is given by:

-k(∂T/∂x) = h(Tb - T)

The initial condition is:

T(x, t=0) = Ti

Note that the properties of the pan material, including ρ, c_p, and k, need to be specified in order to solve the heat equation.

To know more about Heat equation , check out :

https://brainly.com/question/25603269

#SPJ4

Answer:n to the right to the right

Explanation:

A) and B): No force whenever, F(t) = 0, ∀t. C): A constant force,

F(t) = F0,∀t.

Newton's Laws

In the year 1687, Isaac Newton distributed his fundamental work "Philosophiae Naturalis Principia Mathematica", in which he included three essential standards of movement. These standards are referred to now as Newton's maxims or Newton's laws.

A) and B): No force whenever,

F(t) = 0, ∀t.

As indicated by Newton's most memorable regulation, an article moves with constant velocity when no net force is following up on it.

C): A constant force,

F(t) = F0,∀t.

As indicated by Newton's subsequent regulation, the speed increase is corresponding to the acting force. Assuming that the speed increase is constant, the force is constant.

to know more about Newton's law click here:

https://brainly.com/question/28171613

#SPJ4

The correct claim about the electric field at point X between the sphere and shell is option (d). The electric field is zero, because a Gaussian sphere concentric with the sphere with X on its surface encloses zero net charge.

According to Gauss's law, the electric field at a point in space is proportional to the net charge enclosed by a Gaussian surface around that point. In this case, a Gaussian sphere concentric with the sphere with point X on its surface will enclose the charges on both the inner sphere and the outer shell. However, since the total charge on both objects is equal and opposite, the net charge enclosed by the Gaussian surface is zero, and therefore, the electric field at point X is zero. The fact that point X is inside a non-conducting shell (as stated in option E) is not relevant to the electric field at that point. Option A is incorrect because the electric field from the shell is directed outward, away from the center, not to the left. Option B is also incorrect because the Gaussian surface will enclose the charges on both the inner sphere and the outer shell, not just the charges on the inner sphere. Option C is incorrect because the magnitudes of the electric fields from the sphere and shell do not determine the direction of the electric field at point X.

Learn more about Gauss’ Law here brainly.com/question/14767569

#SPJ4

The new potential difference when the distance between the plates vary is calculated to be 0.5 V. Correct option is C.

The parallel plate capacitor's area is denoted by the letter A.

Distance between the plates is d.

Potential difference is V.

If the distance is reduced to d/2, the potential difference is to be found out.

We know that, Q = C V

To find out potential difference, make it as subject,

V = Q/C

From the above equation, it is seen that, capacitance is inversely proportional to potential difference.

So,  V C = k

where,

k is contant

The parallel plate capacitor's capacitance is stated as,

C = εA/d

When the distance apart is d. Then, C₁ = εA/d

When the distance is half d/2

C₂ = εA/(d/2)

C₂ = 2εA/d

Then, applying V C = k

V₁ is voltage of the full capacitor V1 = V

V₂ is the required voltage let say V'

Then,

V₁ C₁ = V₂ C₂

V × εA/d=V' × 2εA/d

VεA/d = 2V'εA/d

Then the εA/d cancels on both sides and remains

V = 2V'

Then, V' = V/2

Thus, the potential difference is half when the distance between the parallel plate capacitor was reduce to d/2.

To know more about potential difference:

https://brainly.com/question/13404382

#SPJ4

Eau Gaullie treatment a) expected flow rate is 1852 gpm. b) Tank diameter is 41.7 ft. c) input power is 21.1 hP

From flow in tank coefficient equation C_Q = Q/(W×D³)

Q ∝ d³

Qd₁/Qd₂ = d₁³/d₂³

where Eau Gaullie treatment Qd₁ and Qd₂ are different discharges with respect to different diameter, (Qd₁ = 3200 gpm) and d₁ is diameter one ( 12 in) while d₂ is diameter 2 ( 10 in),

now we substitute

Qd₂ = Qd₁(d₂³/d₁³)

Qd₂ = 3200( 10/12)³

Qd₂ = 1852 gpm

∴ expected flow rate is 1852 gpm

next we calculate the head

h ∝ d²

hd₁/hd₂ = d₁²/d₂²

where hd₁ and hd₂ are different heads with respect to different diameter, (hd₁ = 60 ft) and d₁ is diameter one ( 12 in) while d₂ is diameter 2 ( 10 in),

now we substitute

hd₂ = hd₁(d₂²/d₁²)

hd₂ = 60 ( 10/12 )²

hd₂ = 41.7 ft

∴ head is 41.7 ft

Now calculate the input power

W ∝ d⁵

Wd₁/Wd₂ = d₁⁵/d₂⁵

where Wd₁ and Wd₂ are different power with respect to different diameter, (Wd₁ = 60 hp) and d₁ is diameter one ( 12 in) while d₂ is diameter 2 ( 10 in),

now we substitute

Wd₂ = Wd₁(d₂⁵/d₁⁵)

Wd₂ = 60 ( 10/12 )⁵

Wd₂ = 21.1 hP

∴ input power is 21.1 hP

Learn more about Eau Gaullie treatment  here

https://brainly.com/question/17285824

#SPJ4

The tension force is 15 N.

Tension force is a pulling force transmitted through a flexible medium, such as a rope or cable, when it is pulled at both ends. It is directed along the length of the medium and is equal in magnitude at both ends.

In this case we have been told that A 5-kg block is suspended by a rope from the ceiling of an elevator that accelerates downward at 3.0 m/s2 .

We know that the tension force is the force that acts along the rope hence;

Tension = ma

= 5 Kg * 3.0 m/s2

= 15 N

Learn more about tension:https://brainly.com/question/15880959

#SPJ1

The heats gained by cold water in trials 1, 2 and 3 are 3048.6 J, 4311.52 J and 3048.6 J respectively and the heat lost are -6858 J, -4307.84 J and -3593.9 J respectively.

Calculation of Heat Gained by Cold Water:

Trial 1:

Q = (m)(c)(Δ T)

Q = (0.25 kg)(4186 J/(kg x C°))(36°C)

Q = 3048.6 J

Trial 2:

Q = (m)(c)(Δ T)

Q = (0.2 kg)(4186 J/(kg x C°))(52°C)

Q = 4311.52 J

Trial 3:

Q = (m)(c)(Δ T)

Q = (0.3 kg)(4186 J/(kg x C°))(26°C)

Q = 3048.6 J

Calculation of Heat Lost by Hot Water:

Trial 1:

Q = (m)(c)(Δ T)

Q = (0.25 kg)(4186 J/(kg * C°))(-52°C)

Q = -6858 J

Trial 2:

Q = (m)(c)(Δ T)

Q = (0.4 kg)(4186 J/(kg x C°))(-26°C)

Q = -4307.84 J

Trial 3:

Q = (m)(c)(Δ T)

Q = (0.15 kg)(4186 J/(kg x C°))(-75°C)

Q = -3593.9 J

Comparison of Heat Gain and Heat Loss:

In all three trials, the heat lost by the hot water is not equal to the heat gained by the cold water. This discrepancy is likely due to errors in the measurement of the temperature and volume of the water, or due to heat loss to the environment.

Conclusion:

This activity allowed the student to investigate heat transfer and thermal energy conservation. Through the measurement of the temperature of hot and cold water and the calculation of heat gained and lost by each, the student was able to gain a better understanding of these concepts. However, it is important to note that the results may have been affected by errors in measurement, so further experimentation and refinement of techniques may be necessary to obtain more accurate results.

Learn more on heat loss and gain here: https://brainly.com/question/14702484

#SPJ1

The rate constant be at 172.0°C  is 1.11 x10⁵ m⁻¹s⁻¹

We employ the Arrhenius equation, which is: to determine the rate constant for the reaction at two different temperatures.

Ln(k  172.0°C/ k 201°C) = Ea/R (1/T₁ - 1/T₂)

where,  

k 201°C = equilibrium constant at  201°C = 5x 10⁴m⁻¹s⁻¹

k 172.0°C = equilibrium constant at 172.0°C = ?

Ea = Activation energy = 30.0 kJ/mol = 30000 J/mol   (Conversion factor:  1 kJ = 1000 J)

R = Gas constant = 8.314 J/mol K

T₁ = initial temperature = 201°C =  474°K

T₂ = final temperature =   172.0°C = 445 °K

Putting the value

Ln(k  172.0°C/ k 201°C) = 30000 J/mol /8.314 J/mol K (1/ 474°K - 1/445 °K)

k 172.0°C = 1.11 x10⁵ m⁻¹s⁻¹

Learn more about rate constant at https://brainly.com/question/15245929

#SPJ4

The car's speed just after the gravel is loaded is 4.00 m/s.

The momentum of the system (railroad car + gravel) is conserved before and after the gravel is dropped.

Therefore, we can use the law of conservation of momentum to find the velocity of the combined system just after the gravel is loaded.

Before the gravel is dropped, the momentum of the railroad car is:

p1 = m1v1 = (10000 kg)(8.00 m/s) = 80000 kg*m/s

where m1 is the mass of the railroad car and v1 is its velocity.

When the gravel is dropped, the total mass of the system becomes:

m2 = m1 + m_gravel = 10000 kg + 6000 kg = 16000 kg

where m_gravel is the mass of the gravel.

The momentum of the system just after the gravel is dropped is:

p2 = m2v2

where v2 is the velocity of the combined system just after the gravel is loaded.

Since momentum is conserved, we can equate p1 to p2:

p1 = p2

m1v1 = m2v2

Solving for v2, we get:

v2 = (m1v1) / m2

Substituting the given values, we have:

v2 = (10000 kg)(8.00 m/s) / 16000 kg

v2 = 4.00 m/s

Therefore, the car's speed just after the gravel is loaded is 4.00 m/s.

To learn more about the law of conservation:

https://brainly.com/question/7538238

#SPJ4

The value of KB when KA and KC are given along with their thickness is calculated to be 1.57 W/m.K.

The value of thermal conductivity kA is given as = 20 W/m.

The value of thermal conductivity kC is given as = 50 W/m.

The thickness LA is given as = 0.30 m.

The thickness LB is given as = 0.15 m.

The thickness LC is given as = 0.15 m.

Temperature on the inner surface Ts,0 = 20 degrees

Temperature on the outer surface Ts,i = 600 degrees

Temperature at infinity = 800 degrees

Convection coeffiecient h = 25W/m²

Thermal resistance due to conductivity,

R = L/KA

Thermal resistance due to heat transfer coefficient

R' = L/KA

We know that heat transfer Q

Q = ΔT /Rth

By equating heat,

(600 - 20)/[LA/A KA + LB/B KB + LC/C KC] = (800 - 20)/[LA/A KA + LB/B KB + LC/C KC + 1/Ah]

(600 - 20)/[0.3/20 + 0.15/B KB + 0.15/50] = (800 - 20)/[0.3/20 + 0.15/B KB + 0.15/50 + 1/25]

580/[0.015 + 0.15/ KB + 0.003] = 780/[0.015 + 0.15/ KB +0.003 + 0.04]

580/(0.018 + 0.15/ KB) = 780/(0.058 + 0.15/ KB)

580(0.058 + 0.15/ KB) = 780(0.018 + 0.15/ KB)

33.64 + 87/KB = 14.04 + 117/KB

33.64 - 14.04 = 117/KB - 87/KB

19 = 1/KB (117 - 87)

19 KB = 30

KB = 30/19 = 1.57 W/m.K

To know more about thermal conductivity:

https://brainly.com/question/13450387

#SPJ4

According to the question, the work done by a car is calculated as 144Nm.

Force may be defined as a process of pushing or pulling on an object that significantly produces acceleration in the body on which it acts. It is an external agent capable of changing a body's state of rest or motion. It has a magnitude and a direction.

According to the question,

The force applied on a car = 18 N

The displacement made by a car = 8m.

Now, the work done is calculated with the help of the given formula:

                           = 18 N × 8m = 144Nm.

Therefore, the work done by a car is calculated as 144Nm.

To learn more about Force and displacement, refer to the link:

https://brainly.com/question/28356414

#SPJ9

(a) Work done by the cord's force on the block [tex](WF) = Mg/4\times d[/tex]

(b) Work done by the weight of the block [tex](Wg) = Mg/4 \times d[/tex]

(c) Kinetic energy of the block [tex](K) = Mg/2\times d[/tex]

(d) Speed of the block [tex](v) = sqrt(gd/2)[/tex] where g is the acceleration due to gravity and d is the distance the block has fallen.

Kinetic energy is the energy that an object possesses due to its motion. In other words, if an object is moving, it has kinetic energy. The amount of kinetic energy an object has depends on its mass and velocity. The formula for calculating kinetic energy, K, is:

K = 1/2 mv^2

where m is the mass of the object and v is its velocity. The factor of 1/2 in the formula is due to the work-energy principle, which states that the work done on an object is equal to the change in its kinetic energy. If a force is applied to an object to put it in motion, work is done on the object, and its kinetic energy increases.

The units of kinetic energy are joules (J). One joule is defined as the amount of work done when a force of one newton (N) is applied over a distance of one meter (m). Since work and energy are measured in the same units, the unit of kinetic energy is the same as the unit of work, which is the joule.

Kinetic energy is a scalar quantity, which means it has magnitude but no direction. The kinetic energy of an object increases as its mass and velocity increase.

(a) The work done by the cord's force on the block can be found using the formula:

[tex]WF = force\times distance[/tex]

The force applied by the cord is equal to the tension in the cord, which is equal in magnitude to the weight of the block. Therefore, the force applied by the cord is:

[tex]F = Mg[/tex]

where M is the mass of the block, and g is the acceleration due to gravity.

The distance over which the force is applied is d, the distance the block has fallen. Therefore, the work done by the cord's force on the block is:

[tex]WF = Fd = Mg \times d[/tex]

Substituting g/4 for g

[tex]WF = M(g/4) \times d = Mg/4 \times d[/tex]

Hence, the work done by the cord's force on the block is Mg/4 × d.

(b) The work done by the weight of the block can be found using the formula:

[tex]Wg = force \times distance[/tex]

The weight of the block is equal to its mass times the acceleration due to gravity, which is:

[tex]W = Mg[/tex]

The distance over which the weight is applied is again d. Therefore, the work done by the weight of the block is:

[tex]Wg = Wd = Mg\times d[/tex]

Substituting g/4 for g:

[tex]Wg = M(g/4) \times d = Mg/4 \times d[/tex]

Hence, the work done by the weight of the block is also [tex]Mg/4 \times d.[/tex]

(c) The change in the kinetic energy of the block can be found using the work-energy principle:

Wnet = ΔK

where Wnet is the net work done on the block, and ΔK is the change in the kinetic energy of the block.

The net work done on the block is equal to the sum of the work done by the cord's force and the work done by the weight of the block:

[tex]Wnet = WF + Wg = Mg/4 \times d + Mg/4 \times d = Mg/2 \times d[/tex]

The change in the kinetic energy of the block is equal to the net work done on the block:

ΔK = Mg/2 × d

Since the block starts from rest, its initial kinetic energy is zero. Therefore, the final kinetic energy of the block is equal to the change in kinetic energy:

[tex]K = Mg/2\times d[/tex]

(d) The final speed of the block can be found using the equation for the final kinetic energy:

[tex]K = 1/2 mv^2[/tex]

where m is the mass of the block, and v is its final speed.

Substituting Mg/2 × d for K and M for m

[tex]Mg/2\times d = 1/2 Mv^2[/tex]

Simplifying and solving for v, we get:

[tex]v = sqrt(gd/2)[/tex]

Therefore, the speed of the block is[tex]sqrt(gd/2)[/tex], where g is the acceleration due to gravity and d is the distance the block has fallen.

To know more about Kinetic Energy, visit:

https://brainly.com/question/8101588

#SPJ4