on to Hand Tools - Scored Items
Item 11 of 25
When working above the when working above the ground, what should be used to connect all tools to prevent injury to others or damage to the work below?

Answers

Answer 1

A lanyard should be used to connect all tools to prevent injury to others or damage to the work below when working above the ground.

What is OSHA?

OSHA is an abbreviation for occupational safety and health administration and it is an agency of the federal government that is saddled with the following responsibilities:

Assuring and ensuring safe and healthy working conditions for workers.Setting and enforcing standards, rules, and laws.

According to the Occupational Safety and Health Administration (OSHA), a lanyard should be used by workers to connect all tools, so as to prevent injury to other workers or even a damage to the work below, especially when working above the ground.

Read more on OSHA here: brainly.com/question/17199752


Related Questions

A transistor with a height of 0.4 cm and a diameter of 0.6 cm is mounted on a circuit board. The transistor is cooled by air flowing over it with an average heat transfer coefficient of 30 W/m2°C air = 30°C If the air temperature is 55°C and the transistor case temperature is not to exceed 70°C, determine the amount of power this transistor can dissipate safely. Disregard any heat transfer from the transistor base.

Answers

The minimum safety power that is safely dissipated using a transistor of height 0.4cm and diameter 0.06cm is 0.04665

Calculation for the exposed area

[tex]\pi DL +\frac{\pi }{4} D^2\\\\Area = 3.14 * 0.6*0.4+\frac{3.14}{4} *0.6^2[/tex]

D = diameter = 0.6cm

Length = height = 0.4cm

Area = 1.0367cm²

minimum safety heat that is dissipated

hA (Ts - Tair)

30 * 1.0367 x 10⁻⁴(70-55)

= 0.04665

The minimum safety power that is safely dissipated is 0.04665W

Read more on energy here: https://brainly.com/question/13881533

Darron loves his career because it mostly fits in with his lifestyle. He likes how he is able to make a lot of money and
stay very busy while at work. He also likes that he travels a lot and gets to see new places. He thinks that one of the
reasons he is successful is that he enjoys the competition in his career that some people would find stressful.
However, he wishes he had more time at home with his family.
Which aspect of Darron's career matches his lifestyle but is also in conflict with some of his desires?
® busyness while at work
® earning money
O frequent travel
© strong competition

Answers

Answer:

A

Explanation:

He says he loves work, but wants more time with his family, so this is in conflict with some of his other desires.

The steel bracket is used to connect the ends of two cables. if the allowable normal stress for the steel is sallow = 30 ksi, determine the largest tensile force p that can be applied to the cables. assume the bracket is a rod having a diameter of 1.5 in.

Answers

The largest tensile force that can be applied to the cables given a rod with diameter 1.5 is 2013.15lb

The static equilibrium is given as:

F = P (Normal force)

Formula for moment at section

M = P(4 + 1.5/2)

= 4.75p

Solve for the cross sectional area

Area = [tex]\frac{\pi d^{2} }{4}[/tex]

d = 1.5

[tex]\frac{\pi *1.5^{2} }{4}[/tex]

= 1.767 inches²

Solve for inertia

[tex]\frac{\pi *0.75^4}{4}[/tex]

= 0.2485inches⁴

Solve for the tensile force from here

[tex]\frac{F}{A} +\frac{Mc}{I}[/tex]

30x10³ = [tex]\frac{P}{1.767} +\frac{4.75p*0.75}{0.2485} \\\\[/tex]

30000 = 14.902 p

divide through by 14.902

2013.15 = P

The largest tensile force that can be applied to the cables given a rod with diameter 1.5 is 2013.15lb

Read more on tensile force here: https://brainly.com/question/25748369

Steering and suspension question

Answers

Answer:

I would say only A

Explanation:

steering dampeners are applied to heavy-duty and off-road vehicles in order to help stabilize and balance out your steering in rough terrain. luxury cars won't have them because, well, they are cars, and cars are not used for off-roading. trucks and SUVs and sometimes vans are though, which makes sense more than just a random luxury car with dampeners just sitting there for no reason at all when heavy-duty vehicles need them more than the car.

Explain what a structural engineer does?

Answers

Explanation:

Structural Engineers create drawings and specifications, perform calculations, review the work of other engineers, write reports and evaluations, and observe construction sites. A Professional Engineer's license is required in order to practice Structural Engineering.

Damage reports should contain the information needed for what?

Answers

Answer:

it's damage kindly be careful

A conductive loop on the x-y plane is bounded by rho = 2.0 cm, rho = 6.0 cm, φ = 0º and φ = 90º. 2.0 a of current flows in the loop, going in the aφ direction on the rho = 2.0 cm arm. determine h at the origin

select one:
a. 8.4 az (a/m)
b. 4.2 ay (a/m)
c. 8.4 ax (a/m)
d. 4.2 az (a/m)

Answers

Answer:

b. 4.2 az (A/m)

Explanation:

b is the answer

b) Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k = 1.8 W/m·K, and surface area A = 30 m2. The left side of the wall is maintained at a constant temperature of T1 = 90°C while the right side loses heat by convection to the surrounding air at

Answers

Answer:

A is correct

Explanation:

I took the test

Calculate the acceleration of a 2000kg single engine airlane just before take off when the thrust of the engine is 500n?

Answers

Answer:

0.25 m/s²

Explanation:

Pouring molten aluminum into a mold and allowing it to cool forms:
A)
a stamped part.
B)
a cast part.
C)
an extruded part.
D)
a hydroformed part.

Answers

Hi :)

The answer is B. A cast part

How does a cast part form?

Molten material is then poured into a mould cavity that takes the form of the finished part. The molten material then cools, with heat generally until it solidifies into the desired shape.

Hope this helps!

Give the other person brainliest, they answered first

Hope this helps!

~NatLikesAnime~

#LearningWithBrainly.

#LearnWithBrainly

In surveying , supposing we can not pull the tape because it is passing through a shallow river. What will i do to obtain an accurate distance?​

Answers

Answer:

Hold the tape in place and go down to the end.

Explanation:

Construction engineering does not have much to do with design.
True
False

Answers

i’m pretty sure it is false .

It was a mistake that i put in under 13 of age can you put it for 27

Answers

Answer:

ill try to help you :)

Explanation:

10 tasks and 5 exercises. How many ways are there to build the test?

Answers

To find how many ways, you must simply multiply 10 tasks and 5 exercises

    Ways: = 10 * 5 = 50 ways

Hope that helps!

In approximately 50 words, describe one thing a professional in an increased demand green construction occupation could do to add to the function, sustainability, and energy efficiency of the construction of a shopping center.


answer:Numbers of green increased demand occupations are growing and include power system operators and dispatchers. There are many green enhanced skill occupations which are being changed; some examples include continuous mining machine operators, electrical engineers, geological sample test technicians, mechanical engineers, and power plant operators, who are all receiving new tasks related to renewable energy generation

Answers

The things that the professional in an increased demand green construction occupation can add in the construction of a shopping center include:

Radiant floors.Solar power.Great water recycling.

What is a green buidling?

It should be noted that a green building simply means a design, construction, or operation that eliminates the negative impact on the climate and natural environment.

In this case, in order to illustrate energy efficiency, it's important to use radiant floors, geothermal system, energy efficient window systems, etc.

Learn more about green building on:

https://brainly.com/question/6560347

does advanced auto parts install engine air filter

Answers

Answer:

You have to do it yourself.

Explanation:

Which part of the electromagnetic spectrum is used in televisiions

Answers

Answer:

Television's use 2 portions of the electromagnet spectrum and that is Visible light and radio waves.

Explanation:

Visible light helps us see the picture on the television and radio waves are used to send pictures to television's screen.

Might a synchronous motor equally well be called a synchronous inductor

Answers

In Engineering, a synchronous motor is sometimes referred to as synchronous capacitor but not a synchronous inductor.

What is a synchronous motor?

A synchronous motor can be defined as an alternating current (AC) electric motor in which the rotation speed of the shaft is directly proportional to the frequency of the supply current, especially at steady state.

Basically, a synchronous motor is sometimes referred to as a synchronous capacitor because it can be used to correct the power factor (PF) of a lagging load such as an induction motor.

However, a synchronous motor cannot be called a synchronous inductor because the rotation speed of the shaft is not proportional to the synchronous speed of the motor. Thus, they are called an synchronous motor.

Read more on synchronous motor here: https://brainly.com/question/12975042

During the design of spherical pressure vessel for space programs, a primary criterion is the mass of the vessel (which determines how much it costs to put it into the orbit). Given the stress in a thin walled spherical vessel is tensile and given by:

Answers

Tensile stress in a thin wall spherical shell is given by

σ = ( p r ) /2t

Tensile stress

This is the type of stress that involves pulling out. it is the opposite of compressive stress.

The tensile stress, σ  at the circumference of the shell is the hoop stress. The value equals that of pressure acting on the area.

Therefore:

σ * 2πr * t = p * πr^2

where

2πr = circumference of a circle

πr^2 = area of a circle

p = internal pressure

t = thickness

σ * 2πr * t = p * πr^2

σ = ( p r ) /2t

Read more Tensile stress here:

https://brainly.com/question/25748369

Joe maylan an employee of acme company has been sent to do some work in the highland company's main lobby. This job will take two days. Which type of pass should joe be given?

Answers

The type of Pass that Joe Maylan should be given is called; Temporary Pass

What is temporary pass?

In factories or industries, there are different types of pass given to workers and visitors visit such places on a daily basis. In this case Joe maylan is going to do a job in the company for just 2 days and as such the type of pass he willl get will be a temporary pass.

It will be a temporary pass because it is a document pass issued for short-term use or due to an emergency.

Read more about temporary pass at; https://brainly.com/question/364363

In-------process the hot drawn bar or rod is pulled through the die.

Answers

Answer:

Explanation:

he metallic rod is fixed into the dies by using a die holder and then a drawing head is used in which the metallic rod is fixed through a jaw mechanism. And then the bar is stretched and slides between the surfaces of the die

What is the definition of gross axle weight rating?.

Answers

The definition of gross axle weight rating is to give give out the weight the axle of a vehicle can support.

Explain how the ideal vapour compression refrigerator cycle is an improvement upon the Carnot cycle. Use any two of the problems to explain.

Answers

answer explanation:Basically, the Carnot cycle is turning a heat differential into mechanical energy, then using mechanical energy to recreate the heat differential. A heat pump only turns mechanical energy into a heat differential. It exchanges the gas being compressed on an ongoing basis and does not extract mechanical energy from it, this continuous loss of mechanical energy input is what allows continuous generation of a heat differential.

Also, the Carnot cycle is an idealized theoretical model, not a practically achievable engineering goal. It illustrates the essential mechanism by which heat differentials can be turned into mechanical energy and vice versa, it has to ignore the fact of inefficiency in conversion between mechanical energy and heat differential for the sake of illustrating a set of ideal processes. A real refrigeration system has to deal with the question of whether the system is pumping away more heat than it generates itself through inefficiency.

Which organization would provide business and leadership training to a high school hospitality student?

Answers

Answer:

Future Business Leaders of America

Explanation:

Give two disadvantages of a moving coil Meter

Answers

1.Only suitable for dc
2.more expensive than moving iron type
3. Easily damaged

A glass of water with a mass of 0.45kg at 20∘C is to be cooled to 0∘C by dropping ice cubes at 0∘C into it. The latent heat of fusion of ice is 334kJ/kg, and the specific heat of water is 4.18kJ/kg⋅∘C. The amount of ice that needs to be added is.

Answers

By using the concept of heat transfer, we need to add 0.045kg or 45g of ice to the glass of water to cool it from 20∘C to 0∘C.

The heat lost by the water is equal to the heat gained by the ice cubes. We can use the following equation to calculate the heat transfer:

Q = m_w * c_w * ΔT + m_i * L_f

where Q is the heat transfer, m_w is the mass of water, c_w is the specific heat of water, ΔT is the temperature change (20-0 = 20∘C), m_i is the mass of ice, and L_f is the latent heat of fusion of ice.

We know the values of m_w (0.45kg), c_w (4.18kJ/kg⋅∘C), ΔT (20∘C), and L_f (334kJ/kg). We can rearrange the equation to solve for m_i:

m_i = (Q - m_w * c_w * ΔT) / L_f

Substituting the values, we get:

m_i = [(0.45kg) * (4.18kJ/kg⋅∘C) * (20∘C) - 0] / (334kJ/kg

m_i = 0.045kg

For more such questions on heat transfer:

https://brainly.com/question/31065010

#SPJ11

When are we going to abandon internal combustion engines?

Answers

Answer:

2035

Explanation:

Most car and truck companies say that they will completely get rid of internal combustion engines by 2035.

What is the purpose of networking?

Answers

Answer:

The purpose of networking is to make new friends, industry acquaintances, and even business partners.

Omar owns a stall selling handmade cosmetics, and wants to launch an e-commerce site. He has lots of experience selling his products in person at markets, but is now hoping to reach more customers online.

Can you advise Omar on how to make both his online and offline business successful?

Answers

Answer:

He could put up advertisements all over the town and pay a few websites or search engines to have his company and ads be more common. He should also use some designs and make his company's sign very adequate.

state 5 general rules for cleat wiring​

Answers

1. Every installation is to be properly protected near the point of entry of supply cables by a two-pole linked main switch and a fuse unit. In a two-wire installation if one pole is permanently earthed, no fuse, switch or circuit breaker is to be inserted this pole. A 3-pole switch and fuse unit is to be used in 3-phase supply.

2. The conductor used is to be of such a size that it may carry load current safely.

3. The conductors installed are to be safe in all respects.

4. Every sub-circuit is to be connected to a distribution fuse board.

5. Every line (phase or positive) is to be protected by a fuse of suitable rating as per requirements.
Other Questions
A circular flower bed is 24m in diameter and has a circular sidewalk around it that is 2m wide. Find the area of the sidewalk in square meters. Use 3.14 for pie (round to nearest 10th) solve pls brainliest Which fraction is closer to 0 than to 1 ? Choose all that apply .A. 5/8B. 2/6C. 1/4 D. 4/6E. 3/8 kassim has amoney box containing 100 mixed sh 5 and sh 10 coins with a totalvalue of sh 600. How many of each type of coin does the box contain What is the area of the quadrilateral Construction crafts are what kind of jobs?A: AcademicB: TheoreticalC: Physical A rule for creating a pattern is given below.Rule: Subtract 7 from x to get y.Which ordered pair, (x, y), works for the rule?Choose 1 answer:(Choice A) (10, 17)(Choice B) (7, 0)(Choice C) (14, 2) Which of these is true of Alabama's economy after World War II? A) Alabama's economy weakened dramatically after the war. B) The military bases built before World War II were shut down after the war, hurting the Alabama economy. C) New technologies developed in wartime allowed Alabama to become a leader in the space industry after the war. D) Many soldiers came back to Alabama after the war with no where to work, creating a large homeless population in urban areas. ILL GIVE BRAINLIST THING IF YOU HELP PLEASE QUICK 0.5mol/dm3 hydrochloric acid is added gradually to a flask containing 20cm3 of 2 mol/ dm3 sodium hydroxide solution.What is the total volume, in cm3, of the mixture in the flask when the solution is just neutral?A 30 B 40 C 60 D 100 when I (see)Joe in the distance, I (wave) at him, but he (not/recognize) me. At Daniel's Swimwear, there are 76 bikini styles and 4 other types of swimsuit. What percentage of the swimsuit styles are bikinis? Emily and Chris are going to the city to visit a friend t They live 65 miles from the city. They have gone 42 miles already. How many more miles do they have to travel How long did a person have to live on the land before it would become theirs Find the values of x and y x= and y= Donovan eats 2 granola bars and drinks 1 glass of orange juice for breakfast every day. The price of a granola bar is B dollars and the price of a glass of orange juice is J dollars. The expression 7(2B+J) describes how much Donovan spends on breakfast in one week. Match each amount in the situation with the expression that represents it. ___________ is the area of dark created when an object blocks light. Every real zero of a polynomial function appears as a/an show work please and no links People with williams syndrome often cannot tie their own shoes, make their beds, or perform simple arithmetic; but often they have great talent in the area of music or language. this illustrates the complexities in developing a definition of: