in which direction will the block move

The length of the bar after loading cannot be determined without a predetermined steel stress-strain relationship.

To calculate the elongation of a one-inch diameter bar under a tensile load of 70,686 pounds, we must use the stress-strain curve of an annealed 1018 steel bar. The diagram shows that the stress corresponding to a tensile load of 70686 lbs. is approximately

1 ksi. Using the stress-strain relationship, we  find the stress corresponding to a strain of

1 ksi, which is approximately 0.0017.

The elongation of a bar can be calculated as the product of the original length, the elongation and the gauge length factor.

Extension = 37 inches * 0.0017 = 0.0629 inches

Therefore, the length of the rod after loading is 37 inches 0.0629 inches = 37.0629 inches (rounded to four decimal places).

learn more about stress-strain here:

https://brainly.com/question/13261407

#SPJ4

Templates are tosca elements that need to be added to requirements as per best practices.

Why do Templates need to be added?

Before you can run your tests, you must perform tasks manually that Template Selection enables you to automate. You can carry out the following actions in Step 3:

• The Test Case templates you want to employ for your tests should be chosen.

• Make a list of the test cases that will be executed or an execution list.

• Make a set of functional or non-functional criteria called a requirement set to evaluate the business risk of a test project.

What are Templates?

A file used as a model for a new document is known as a template. Templates have pre-filled placeholder fields and expertly crafted styles and layouts. When creating a new file, many word processors, presentations, desktop publishing products, and even website providers include template galleries that you can peruse.

To know more about templates, Check out:

https://brainly.com/question/13042079

#SPJ1

Pressure in pipe b is 0.6 psi + (2.6 * 0.6 psi) = 2.56 psi due to the differential reading shown in the inclined-tube manometer with a specific gravity of 2.6 for the gage fluid.

The pressure in pipe b is 1.56 psi.

The fluid in both pipes a and b is water, so the height of the water column in both pipes is proportional to the pressure.

The gage fluid in the manometer has a specific gravity of 2.6, so its height in the manometer will be 2.6 times greater for a given pressure than the height of water in the same manometer.

Therefore, the differential reading of 6.2 units in the manometer represents a difference in pressure of 6.2 / 2.6 = 2.38 psi between the two pipes.

Since the pressure in pipe a is 0.6 psi, the pressure in pipe b must be 0.6 + 2.38 = 1.56 psi.

Learn more about Pressure here:

https://brainly.com/question/12971272

#SPJ4

False. When voltage levels lag (experience a momentary decrease), the extra voltage can severely damage or destroy equipment. Voltage levels that increase can cause damage as well, but not as severely as when they decrease.

Voltage is a measure of electrical potential energy per unit charge. It is the difference in electrical potential between two points in an electrical circuit, and the amount of work required to move a unit charge from one point to the other. Voltage is measured in units of volts (V). Voltage is an important concept in electricity since it is responsible for the flow of current in a circuit. Voltage is also used to measure the power of a source, such as a battery. Voltage is used to power a variety of electrical devices, including motors and lights. In addition, the voltage of a circuit can be adjusted to regulate the current, or the flow of electrons.

To learn more about voltage

https://brainly.com/question/30148871

#SPJ4

Anodization of aluminium, by the electrolytic treatment can be used for all of the three given options. Hence option (D) is the answer.

Electrolytic treatment of metals is used in the anodizing process, which results in the formation of durable films or coatings on the metals' surfaces. A surface layer of an aluminium substrate is transformed into an aluminium oxide layer through the electrochemical passivation process of aluminium anodizing. This process is useful in the field of chemical engineering.

On aluminium, there is a natural oxide layer, although it is frequently crooked, scant, and provides inadequate protection. Anodizing reduces or completely gets rid of color differences while offering a huge array of gloss and color options. In contrast to other finishes, anodizing enables the aluminium to keep its metallic appearance. Greater long-term value is produced by a cheaper initial cost of finishing and lower ongoing maintenance expenditures.

To learn more about chemical engineering, visit:

https://brainly.com/question/18071264

#SPJ4

The complete question is:

Anodization of aluminum can be used to:

A. Protect against corrosion.

B. Change the color of aluminum.

C. Make the surface harder.

D. All three of these.

The turbojet draws air in and squeezes or compresses it. The turbine is spun by the gases that pass past it.

The gases cause the exhaust to blast out the back and bounce back, propelling the aircraft forward. All of the intake air enters the turbojet and flows through each component of the engine. The incoming air pressure is increased by the compressors; for certain engines, the pressure ratio can be as high as 30 to 1. The combustor, where fuel is injected, is entered by the high-pressure air. The idea behind turbojet aircraft is to rapidly accelerate a comparatively small mass of air. Turbojet engines don't operate at their maximal efficiency since it happens when the air being accelerated is moving at a speed that is close to that of the airplane.

Learn more about efficiency here-

https://brainly.com/question/13154811

#SPJ4

Surveys provide detailed elevation data that is essential for accurate mapping, especially in areas with complex terrain.

What is Mapping?
Mapping is the process of creating a visual representation of an area. It involves taking geographical information and representing it on a two-dimensional plane. This can be done through various methods, such as drawing on a piece of paper, using a computer program, or using a GPS device. Mapping can be used to show the physical features of an area, such as roads, rivers, and mountains. It can also be used to display information such as population density, land use, and other data. For example, a map of a city can show which areas are most populated, or which areas have the highest crime rates.

To know more about Mapping
https://brainly.com/question/28989903
#SPJ4

The filter shown in the diagram is a low-pass filter, which is a type of electrical filter that allows low-frequency signals to pass through while blocking high-frequency signals.

(a) The type of the filter can be determined using qualitative analysis by examining the diagram. The presence of a single inductor (L) and capacitor (C) in series with the input signal indicates that this is an LC filter, which is a type of passive filter. The LC filter is commonly used in low-pass filters, and the cut-off frequency can be determined from the values of L and C.

(b) The filter transfer function is a mathematical expression that describes the relationship between the input signal and the output signal of the filter. The transfer function for a low-pass LC filter can be determined using the Laplace transform and is given by:

H(s) = (1/ (Ls + 1/Cs))

Where H(s) is the transfer function, L is the inductance in henries, C is the capacitance in farads, and s is the Laplace variable.

(c) The cut-off frequency of a low-pass filter is the frequency at which the output signal is reduced by 3 dB (or 70.7%) relative to the input signal. The cut-off frequency can be determined from the values of L and C and is given by:

f_c = 1 / (2π * √(L * C))

Where f_c is the cut-off frequency in hertz, L is the inductance in henries, and C is the capacitance in farads.

In conclusion, the filter shown in the diagram is a low-pass LC filter, and the filter transfer function and cut-off frequency can be determined using the mathematical expressions provided above. It is important to note that the values of L and C must be known to determine the filter transfer function and cut-off frequency accurately.

To know more about frequency: https://brainly.com/question/14316711

#SPJ4

The loop-current method is a widely used method in circuit analysis to determine the loop currents in a circuit.

This method involves the use of Kirchhoff's current law to write equations for each loop in a circuit. The current law states that the sum of the currents entering a node is equal to the sum of the currents leaving the node. Using this method, we can write a set of equations for each loop in the circuit. For example, for a circuit with three loops, we would write three equations, one for each loop. These equations would relate the loop currents to the sources and the resistors in the circuit. To simplify the equations, we would use Ohm's law to express the currents in terms of the voltages and resistances in the circuit. We would then substitute the known values for the sources and the resistors into the equations to obtain a set of three equations in terms of the loop currents.

Learn more about Kirchhoff's current law :

https://brainly.com/question/20040468

#SPJ4

Given that the variable price per pencil contains the cost per individual pencil, the price per dozen pencils is calculated as follows: price per dozen = price per pencil * 12.

It's dreadful to be an adult and appear childish; a pencil will never leave ink smudges on your hands or clothing. 10. Pencils cost little. A pencil generally costs less and hence is unquestionably more tempting than a pen.

Kaolinite's chemical composition is Al2O32SiO22H2O. In other words, it contains aluminium oxide and another substance.

To know more about variable bvisit:-

https://brainly.com/question/14823479

#SPJ1

To produce a signal with rising amounts of harmonic signal and decreasing levels of noise to a cutoff frequency of 400 Hz, low-pass filtering raises the ratio of harmonic signal to noise.

Low pass filter: The image is smoothed using this particular style of frequency domain filter. The low frequency components are preserved while the high frequency components are attenuated. High pass filter: A high pass frequency domain filter is used to enhance the sharpness of the image. A voltage-to-current converter, or resistor, is used in an RC circuit to "convert" the input voltage into the output current. In reality, the resistor just uses Ohm's law to calculate the current.

Learn more about voltage here-

https://brainly.com/question/29445057

#SPJ4

Classify each structure shown below a stable or unstable. If stable, determine whether they are statically determinate or statically indeterminate. Explain your reasoning.

Alternative Method. f_{i}=4, n_{r}=3, r+f_{i}=5+4=9fi=4,nr=3,r+fi=5+4=9, and 3 n_{r}=3(3)=93nr=3(3)=9. Because r+f_{i}=3 n_{r}r+fi=3nr, the beam is staticaly determinate externally.

Alternative Method. f_{i}=6, n_{r}=4, r+f_{i}=6+6=12fi=6,nr=4,r+fi=6+6=12, and 3 n_{r}=3(4)=123nr=3(4)=12. Because r+f_{i}=3 n_{r}r+fi=3nr, the structure is statically determinate externally.

Alternative Method. f_{i}=2, n_{r}=2, r+f_{i}=4+2=6fi=2,nr=2,r+fi=4+2=6, and 3 n_{r}=3(2)=63nr=3(2)=6. Since r+f_{i}=3 n_{r}r+fi=3nr, the frame is statically determinate externally.

Alternative Method. f_{i}=6, n_{r}=4, r+f_{i}=6+6=12fi=6,nr=4,r+fi=6+6=12, and 3 n_{r}=3(4)=123nr=3(4)=12. Because r+f_{i}=3 n_{r}r+fi=3nr, the frame is statically determinate externally.

Learn more about determinate here:

https://brainly.com/question/13369636

#SPJ4

We can easily calculate that dotted-decimal notation for this IP address is 140.4.78.12.

What is dotted-decimal notation?

The dotted-decimal notation is a way of writing IP addresses in a human-readable form. An IP address is typically a 32-bit binary number, which can be difficult for humans to read and remember.

To convert the binary IP address to dotted-decimal notation,

each octet (8-bit block) of the binary IP address is converted to its decimal equivalent.

The resulting decimal values are separated by periods, creating the dotted-decimal notation.

Dotted-decimal notation is widely used for IP addresses, including IPv4 and IPv6 addresses, and is an important concept in computer networking and internet communication.

To know more about IP address, visit: https://brainly.com/question/15293687

#SPJ4

If your truck has a  starter button , you must first turn the engine key to the ‘on’ position before engaging it.

An ignition switch, starter switch, or start switch is a switch in a motor vehicle's control system that activates the vehicle's primary electrical systems, including "accessories."

The ignition switch is a critical component of an automobile. It starts and stops the car's engine, as well as the electrical in-car devices. It also powers the starting motor of the automobile. The ignition switch not only turns on and off the engine, but it also powers the lights and radio.

Learn more about Trucks:
https://brainly.com/question/13928690
#SPJ1

Full Question:

If your truck has a(n) _____, you must first turn the engine key to the 'on' position before engaging it. *

10 points

A. starter button

B. engine brake

C. clutch button

D. cruise control

In order to overcome concerns about hackers getting access to the accounts of online shoppers, electronic payment systems such as e-wallets are being developed.

Users of an information system must refrain from using unofficial information, such as rumors, unverified reports, and stories, when resolving issues. Databases are created, arranged, and managed using a database management system (DBMS). Internal, external, and produced are the three main types of data sources. A user must consent to certain rules and procedures in order to use a corporate network, the internet, or other resources, according to an acceptable usage policy (AUP). Before receiving a network ID, many companies and educational institutions demand that staff or students sign an AUP. This entails conserving energy, cutting waste, and fostering sustainability. The goal of "green computing" is to lessen the carbon footprint that the information technology and systems sector, as well as allied businesses, create.

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

The flow stress at a true strain can be calculated using the following equation: F = K * ε^n.

Stress is a physical and mental reaction to an event or situation that is perceived as challenging or threatening. It is the body's way of responding to a demand or a threat and is often referred to as the “fight or flight” response. When a person experiences stress, hormones like cortisol and adrenaline are released, which can lead to physical and mental changes such as an increased heart rate, heightened alertness, and the release of energy. Stress can be both positive and negative, but long-term continuous stress can lead to negative physical and psychological health effects. lp people to manage their stress and reduce its negative effects.

Where K is the strength coefficient and n is the strain-hardening exponent.

In this case, K is 600 MPa and n is 0.3. Therefore, the flow stress at a true strain is given by:

F = 600 MPa * ε^0.3

The true strain is unknown, so the flow stress cannot be determined without it.

To learn more about stress

https://brainly.com/question/12871096

#SPJ4

The mean rating for the variable Rating is 4.230765.

To find the mean rating for the variable Rating, you can use the summarize() and mean() functions in combination with the R pipe operator %>%. The code chunk should look like this:

trimmed_flavors_df %>% summarize(mean_rating = mean(Rating))

Basic statistics is the analysis of data and the use of quantitative methods to draw conclusions from that data. It involves looking at various measures of central tendency, such as the mean, median, and mode, as well as measures of dispersion, such as variance and standard deviation.

Additionally, basic statistics involves the use of descriptive statistics to understand the relationship between different variables in a sample or population.

Learn more about the basic statistics:

https://brainly.com/question/23724696

#SPJ4

The current I2 through resistor R2 is given by the expression I2 = (Vb - Va) / (R1 + R2 + R3).

In this expression, Vb is the voltage across R2 in the positive direction from Va and R1, R2, and R3 are the resistances of the respective resistors.

The current is the flow of electricity in a conductor, usually measured in amperes. It is a measure of the rate at which charge is moving past a given point in a circuit. Current is affected by the voltage applied across a conductor, the resistance of the conductor, and the capacitance of the circuit. Current is also an important quantity in electrical engineering and electronics, as it is used to calculate the power dissipated in a circuit.

Learn more about  the current:

https://brainly.com/question/24858512

#SPJ4

Therefore, after the rod was expanded and its diameter shrank, the maximum primary strain would be 0.0000053.

a. The largest principal strain:

θ = T * r / G * J

where:

J = polar moment of inertia (m^4)

angular deformation (θ) = 1.2 degrees = 1.2 * π / 180 radians

T = F * L

F = force (N)

L = length of the rod (m)

Given, the force (F) = 1 N

Substituting the values, we get

T = 1 N * 1 m = 1 Nm

The radius of the rod (r) = 25 mm = 0.025 m

The shear modulus (G) for AISI 1050 hot-rolled steel can be assumed as approximately 80 GPa (80 * 10^9 Pa)

polar moment of inertia (J) :

J = π * r^4 / 2

J = π * (0.025 m)^4 / 2 = 3.937 * 10^-9 m^4

Substituting the values in the above equation, we get

θ = 1 Nm * 0.025 m / 80 * 10^9 Pa * 3.937 * 10^-9 m^4

= 0.00002088 radians

The maximum principal strain can be calculated using the following formula:

ε = θ * r / L

Substituting the values, we get

ε = 0.00002088 radians * 0.025 m / 1 m

= 0.0000052

b. The new length of the rod (L') = 1 m * 1.012 = 1.012 m

The new radius of the rod (r') = 50 mm * 0.996 = 49.8 mm = 0.0498 m

J' = π * (r')^4 / 2

J' = π * (0.0498 m)^4 / 2 = 3.716 * 10^-9 m^4

angular deformation (θ') :

θ' = T / G * J'

θ' = 1 Nm / 80 * 10^9 Pa * 3.716 * 10^-9 m^4

= 0.00002239 radians

ε' = θ' * r' / L'

ε' = 0.00002239 radians * 0.0498 m / 1.012 m

= 0.0000053

Learn more about strain Visit: brainly.com/question/14288250

#SPJ4

The Force is:

1-FBA = vec(150i - 200j + 0k) N
2-FCA = vec(0i - 200j + 150k) N
3-FDA = vec(150i + 0j - 200k) N

What is Force?
Force is an interaction between two or more objects resulting in a change in their motion, direction, or shape. It is a vector quantity, meaning that it is expressed as a magnitude and direction. Forces can be either contact, meaning that they are a result of physical contact between objects, or non-contact, meaning that they act over a distance. Examples of contact forces include friction, tension, and normal forces, while non-contact forces include gravity and electromagnetic forces.

To know more about Force
https://brainly.com/question/12785175
#SPJ4

According to James Marcia, Maida is exhibiting identity foreclosure. She has made a commitment to a particular identity without exploring other options.

Yes, according to James Marcia's theory of identity formation, Maida's actions and experiences indicate that she is in the stage of identity foreclosure. This means that she has made a commitment to a particular identity, in this case, becoming a doctor, without fully exploring other options or undergoing a crisis of identity. Maida's early exposure to medical equipment and her parents' expectations of her becoming a doctor suggests that her sense of self and career aspirations were influenced by external factors, rather than internal exploration and self-discovery.

It is important to note that identity foreclosure is not necessarily a negative outcome, and many individuals may have a clear and stable sense of self without going through a crisis of identity. However, it is beneficial for individuals to have the opportunity to explore their options and interests in order to make informed decisions about their lives and careers.

Learn more about According to James here:

https://brainly.com/question/11210186

#SPJ4

Since t's value is unknown, we are unable to determine x with precision. However, the value of x can be precisely computed with a big enough amount of t (i.e., enough time for the diffusion to achieve a steady-state condition).

As a nitrogen  atmospheres function at position, x, into the sheet, the concentration profile of nitrogen in steel can be modelled as follows:

C(x) is equal to C0 - (C0 - C) * erf(x / sqrt(D * t))

where:

C0 = 2 kg/m^3

C∞ = 0.5 kg/m^3

D = 1.2 x 10^(-10) m^2/s erf = the error function t = time

In order for C(x) to equal 0.5 kg/m3, we need to determine the depth, or x, within the sheet. By rearranging the equation, we may find the value of x:

erf^(-1) = ((C0 - C) / (C0 - C)) * sqrt(D * t) * x = 2 * sqrt(D * t)

When we enter the values from the problem, we get:

x = 2 * sqrt(1.2 x 10^-10 m^2/s*t) * erf-1((2 kg/m^3 - 0.5 kg/m^3) / (2 kg/m^3 - 0.5 kg/m^3)).

Learn more about atmospheres Visit: brainly.com/question/219386

#SPJ4

The option that best explains what will need to be minimized in the following scenario is energy loss. Thus, the correct option for this question is B.

A fluid power system may be characterized as a type of system that significantly has a pump driven by a prime mover (such as an electric motor or internal combustion engine) that converts mechanical energy into fluid energy.

According to the context of this question, if Walt is designing a fluid power system that will need to produce the least amount of waste possible. It would be required by the systm to reduce or eliminate the chances of energy loss in order to produce least amount of waste product.

Therefore, the option that best explains what will need to be minimized in the following scenario is energy loss. Thus, the correct option for this question is B.

To learn more about Fluid Power system, refer to the link:

https://brainly.com/question/14967131

#SPJ1

Answer:

The correct answer is energy loss

Explanation:

The rate of superelevation is the degree to which the outer edge of the roadway is raised above the inner edge to counteract the centrifugal force on vehicles as they travel through a horizontal curve.

The rate of superelevation is denoted by e and is expressed as a decimal fraction of the roadway width. To calculate the rate of superelevation required for a given horizontal curve, the following formula can be used:

[tex]e = \frac{v^2}{g \times r}[/tex]

where:

v = design speed in feet per second

g = acceleration due to gravity (32.2 ft/s²)

r = radius of the curve in feet

First, we need to convert the design speed of 70 mi/h to feet per second:

70 mi/h × 5280 ft/mi / 3600 s/h

= 102.7 ft/s

Now, we can plug in the values and solve for e:

[tex]e = \frac{(102.7\ \text{ft/s})^2}{(32.2\ \text{ft/s}^2 \times 2500\ ft)}[/tex]

e ≈ 0.15

Therefore, the rate of superelevation required for the given horizontal curve is approximately 0.15, or 15% of the roadway width. This means that the outer edge of the roadway should be raised 15% higher than the inner edge to counteract the centrifugal force on vehicles as they travel through the curve.

To know more about  superelevation: https://brainly.com/question/18687676

#SPJ4

(a) 3D diagram represents an AND gate. ( b) The output has a logical maximum of 5 volts and a logical low of 0 volts.

(a) The logic gate shown in the 3D diagram is an AND gate. This is because the output volt is high only when both input voltages are high, and low in all other cases. An AND gate is a basic logic gate that produces a high output only when all inputs are high.

b. A logic high level of the output is approximately

volts, while a logic low level is approximately 0 volts. These levels can be derived from the height of the output surface above the x-y plane. The output is high (above 3 volts) only when both input voltages are above 2 volts, and low (below 1 volt) in all other cases. The logic high and low levels are important in determining the compatibility of the output with other logic gates or devices.

learn more about volt here:

https://brainly.com/question/29014695

#SPJ4

The lay in the surface symbols is the direction of the machining and grinding operations that have been performed on the material. A sketch of the surface pattern would typically show a series of parallel lines which represent the direction of the machining and grinding operations.

Machining is the process of cutting, shaping, and forming a material using a machine tool. It is a subtractive manufacturing process that involves the removal of material from a workpiece using cutting tools such as milling cutters, lathes, drills, reamers, and taps.

Machining is used to produce parts of all shapes and sizes, and can be used in a variety of industries including automotive, aerospace, medical, and construction.

To know more about Machining

https://brainly.com/question/2641843

#SPJ4

When an agreement fails to meet the definition of an enforceable contract but one of the parties breaches it, the non-breaching party B.) may sue for unjust enrichment.

What happened when an agreement fails as an enforceable contract?

When an agreement fails to qualify as an enforceable contract, the parties are not bound by its terms. However, if one party has received a benefit from the agreement, the non-breaching party may be able to sue for unjust enrichment.

This is a legal principle that requires a person who has received a benefit at the expense of another to return that benefit in order to avoid being unjustly enriched. In this case, the non-breaching party can seek to recover the value of the benefit they provided to the breaching party.

To learn more about enforceable contract, visit: https://brainly.com/question/30036509

#SPJ4

The correct answer is a GET/request handler that serves the webpage with the message board and a "Send" button to initiate the entry of new messages; a server for WebSockets that...

A single TCP connection can provide full-duplex communication channels thanks to the computer communications technology known as WebSocket. In 2011, the IETF standardised the WebSocket protocol as RFC 6455. Currently, the API definition for web applications An advanced technology called the WebSocket API enables a user's browser and a server to start a two-way interactive communication session. Without needing to poll the server for a response, you may use this API to send messages to a server and receive event-driven responses. WebSockets are the ns to use this protocol.A permanent, bi-directional, full-duplex TCP connection from a user's web browser to a server is made possible via the WebSocket protocol.

To learn more about  WebSockets  click on the link below:

brainly.com/question/15744924

#SPJ4

Both Techs A and B were incorrect when they said that sliding/fixed calipers utilize one or more pistons on both edges of the rotor and that fixed calipers using a or even more pistons.

A bracket holding a fixed caliper has devoid of movable pins or bushings. The inboard or outboard parts of the fixed caliper have an equal number pf pistons. It is generally acknowledged that fixed calipers perform better but are more expensive.

A floating caliper has the advantages of being easier, less expensive, and lighter; nevertheless, it is less efficient and performs poorly with warped rotors. Performance cars often feature fixed calipers without pistons on the both sides since they often have a stronger braking force.

To know more about fixed calipers visit:

https://brainly.com/question/26731670

#SPJ1

The area will be maximum of the above two case of the structural member in a nuclear reactor, in which the area is 0.5142 in²

Axial loads, also known as thrust loading, are those that can sustain a force that is directed in the same direction as the axis. On the other hand, radial loads are designed to withstand forces that are parallel to the axis. Axial loads are applied along a structural member's longitudinal or centroidal axis. The member is considered to be under tension and the applied load is tensile if the result of the load is for the member to grow longer.

Given:

Axial load = 4 kip

Factor of safety(FOS) = 3

Length L = 3 ft = 36i

[tex]E_{zx}[/tex] = 14 × 10³ Ksi

[tex]r_{y}[/tex] = 57.5 Ksi

Crossection Area = A

Case 1

FOS = [tex]r_{y}/r_{APPLY}[/tex]

[tex]r_{APP}[/tex] = [tex]r_{y} / FOS[/tex]  = 57.5/3

= P/area = 19.167 Ksi

Area = 4/19167 = 0.20869 in²

Case 2

Elongation = PL/ AE

0.02 = (4×36) / (A × 14 × 10³)

A = 0.51428 in²

To learn more about axial loads, visit:

https://brainly.com/question/30030702

#SPJ4

The complete question is

A structural member in a nuclear reactor is made of a zirconium alloy. if an axial load of 4 kip is to be supported by the member, determine its required cross-sectional area. use a factor of safety of 3 relative to yielding. what is the load on the member if it is 3 ft long and its elongation is 0.02 in.?  [tex]E_{zr}[/tex] = 14(10³) ksi, [tex]sigma _{y}[/tex] = 57.5 ksi. The material has elastic behaviour.