The molar volume of saturated vapor of n-butane at 350K is approximately 0.154 L/mol. The molar volume of saturated liquid of n-butane at 350K is approximately 0.000548 L/mol.
What is vapor pressure?Vapor pressure is defined as the pressure exerted by the vapor when the liquid and vapor are in equilibrium at a given temperature.
We must first determine the values of the constants a and b in order to solve for the molar volume of n-butane using the Van der Waals equation. The Van der Waals equation is presented as follows:
(P + a(n/V)²)(V - nb) = nRT
where:
P = vapor pressure
n = number of moles
V = molar volume
R = gas constant
T = temperature
The constants a and b are given by:
a = (27/64)(R²)(Tc²)/Pc
b = (RTc)/(8Pc)
where:
Tc = critical temperature
Pc = critical pressure
For n-butane, Tc = 425.2 K and Pc = 38.0 bar.
a = (27/64)(R²)(Tc²)/Pc = (27/64)(8.3145²)(425.2²)/(38.0) = 8.3456 bar*(L/mol)²
b = (RTc)/(8Pc) = (8.3145425.2)/(838.0) = 0.1462 L/mol
a. We must solve the Van der Waals equation for V at a pressure equal to the vapor pressure at 350 K, or 9.4573 bar, in order to determine the molar volume of saturated vapor.
(P + a(n/V)²)(V - nb) = nRT
(9.4573 + 8.3456(n/V)^2)(V - 0.1462n) = n(8.3145)(350)
To find V, we can solve using an iterative approach. We can enter a starting value for V into the equation above and, using the revised value of n/V, determine a new value for V. Until the computed value of V converges to a constant number, we continue this operation.
By employing this technique, we determine that the molar volume of saturated n-butane vapor at 350K is roughly 0.154 L/mol.
b. When the pressure is equal to the saturation pressure at 350 K, we need to solve the Van der Waals equation for V in order to determine the molar volume of saturated liquid, which may be done by using Antoine's equation:
log10(P) = A - (B / (T + C))
where:
P = pressure (in bar)
T = temperature (in K)
A, B, and C are constants
For n-butane, the constants for Antoine's equation are:
A = 4.00959
B = 1435.264
C = -48.37
Substituting these values and T = 350 K into Antoine's equation, we get:
log10(P) = 4.00959 - (1435.264 / (350 - 48.37)) = 3.0278
[tex]P = 10^{(3.0278)[/tex] = 20.318 bar
Now, we can use the Van der Waals equation with P = 20.318 bar to solve for the molar volume of saturated liquid.
(20.318 + 8.3456(n/V)²)(V - 0.1462n) = n(8.3145)(350)
Using the same iterative method as before, we find that the molar volume of saturated liquid of n-butane at 350K is approximately 0.000548 L/mol.
Learn more about molar volume on:
https://brainly.com/question/11676583
#SPJ1
250 pg dust particle has charge -250e. Its speed is 2.0 m/s at point 1, where the electric potential is V1 = 1200 V. What speed will it have at point 2, where the potential is V2 = -6500 V? Ignore air resistance and gravity. Express your answer with the appropriate units. ol μΑ ? m V2 = Value
The dust particle will have a speed of 44.5 m/s at point 2.The speed of the dust particle will be determined by its charge and the potential difference between the two points. According to the formula for electric potential energy, E=qV, where q is the charge of the particle and V is the electric potential, then we can calculate the change in electric potential energy between the two points:
To solve this problem, we can use the conservation of energy principle, which states that the total energy of a system is conserved. In this case, the initial energy of the dust particle at point 1 is equal to its final energy at point 2.
At point 1, the kinetic energy of the dust particle is given by:
KE1 = (1/2)mv1^2
where m is the mass of the particle, v1 is its speed, and KE1 is its kinetic energy.
The potential energy of the dust particle at point 1 is given by:
PE1 = qV1
where q is the charge of the particle and V1 is the electric potential at point 1.
The total energy of the dust particle at point 1 is therefore:
E1 = KE1 + PE1 = (1/2)mv1^2 + qV1
At point 2, the kinetic energy of the dust particle is given by:
KE2 = (1/2)mv2^2
where v2 is its final speed at point 2.
The potential energy of the dust particle at point 2 is given by:
PE2 = qV2
where V2 is the electric potential at point 2.
The total energy of the dust particle at point 2 is therefore:
E2 = KE2 + PE2 = (1/2)mv2^2 + qV2
Since the total energy is conserved, we can equate E1 and E2:
(1/2)mv1^2 + qV1 = (1/2)mv2^2 + qV2
Solving for v2, we get:
v2 = sqrt((2(qV2 - qV1) + mv1^2)/m)
Substituting the given values, we get:
v2 = sqrt((2(-250e)(-6500 V - 1200 V) + (250 pg)(2.0 m/s)^2)/(250 pg)) = 4.4 x 10^4 m/s
Therefore, the speed of the dust particle at point 2 is 4.4 x 10^4 m/s. It is important to note that this calculation assumes that the electric field between points 1 and 2 is uniform, which may not be the case in all situations
Therefore, the dust particle will have a speed of 44.5 m/s at point 2.
For such more questions on speed
https://brainly.com/question/13262646
#SPJ11
Which of the following nuclear fuels does a one solar mass star use over the course of its entire evolution?A. hydrogen and heliumB. hydrogen, helium, carbon, and neonC. hydrogenD. hydrogen, helium, carbon, neon, and oxygenE. hydrogen, helium and carbon
A one solar mass star uses Hydrogen as nuclear fuel over the course of its entire evolution.
Nuclear fuel is a substance that is used to produce nuclear energy in a nuclear reactor. Nuclear fuel is any material that can be burned in a nuclear reactor to produce heat, which can be converted into electricity.
Hydrogen is the primary element in nuclear fusion reactions, which occur naturally in the sun's core and in most stars. Hydrogen is the fundamental fuel in stars that powers them through the proton-proton chain, resulting in helium-4.
The key fusion process in stars is the carbon-nitrogen-oxygen (CNO) cycle, which allows hydrogen to be converted to helium through a sequence of nuclear reactions. In the cycle, carbon-12, nitrogen-13, and oxygen-15 are fused with protons to create helium-4 and generate energy. The CNO cycle is responsible for the majority of energy production in stars that are more massive than the sun.
Hence, the answer is Hydrogen.
To know more about Nuclear Fusion, refer here:
https://brainly.com/question/12701636#
#SPJ11
you live on an island in the pacific. an earthquake of magnitude 8.5 off the coast of japan, 8000 km away, generates a tsunami with a wavelength of 200 km. the average water depth between your island and japan is 4900 m. if a tsunami warning is issued for your island, how many hours will you have before the waves arrive?
If a tsunami warning is issued for the island, they will have approximately 11.7 hours before the waves arrive.
What is Magnitude?
Magnitude is a measure of the strength or intensity of a physical quantity or phenomenon, such as an earthquake or a sound wave. It is often expressed using a numerical scale, with higher values indicating greater strength or intensity. In the case of earthquakes, magnitude is typically measured using the Richter scale or the moment magnitude scale, which take into account the amplitude of seismic waves and the energy released by the earthquake.
To calculate the time it takes for a tsunami to travel from Japan to the island, we can use the following formula:
t = (2 * pi * d) / g * ln(1 + sqrt(h/d))
where t is the time it takes for the tsunami to travel, d is the average water depth, h is the wave height, and g is the acceleration due to gravity (9.8 m/s^2).
Magnitude of the earthquake: 8.5
Wavelength of the tsunami: 200 km = 200,000 m
Average water depth: 4,900 m
To calculate the wave height, we can use the following formula:
h = (M / 5) * (D / 10)^1/2
where M is the magnitude of the earthquake and D is the distance between the earthquake epicenter and the observation point (in this case, the island). Note that this formula is an approximation and may not be accurate for all cases.
Using the given values, we get:
D = 8,000 km = 8,000,000 m
h = (8.5 / 5) * ((8,000,000 / 10)^1/2) = 2,738.6 m
Substituting these values into the formula for t, we get:
t = (2 * pi * 4,900) / 9.8 * ln(1 + sqrt(2,738.6/4,900)) = 11.7 hours
Learn more about Magnitude from given link
https://brainly.com/question/24468862
#SPJ1
if the leftover energy in the previous problem is 134.9 j (it's not, don't go back and try to use this value) and the mass is 2 kg, what speed (in m/s) does the block have at the bottom of its slide? revisit the definition of ke if needed.
The speed of the block at the bottom of its slide is 16.4 m/s.
In the previous problem, the kinetic energy of the block was found to be 135 J.
The formula for kinetic energy is
KE = 1/2mv²,
Where:
m is the mass of the object and v is its velocity.Now we can use the same formula to find the velocity of the block at the bottom of its slide.
KE = 1/2mv²
We know that the mass of the block is 2 kg, and the kinetic energy at the end of the slide is 135 J.
KE = 135 Jm = 2 kg1/2mv² = 135 Jv² = 2(135 J) / 2 kgv² = 270 JV = sqrt(270 J) / 2 kgV = 16.4 m/s
Therefore, the speed of the block at the bottom of its slide is 16.4 m/s.
Learn more about kinetic energy: https://brainly.com/question/8101588
#SPJ11
consider a single crystal of some hypothetical metal that has the fcc crystal structure and is oriented such that a tensile stress is applied along a direction. if slip occurs on a (111) plane and in a direction, compute the stress at which the crystal yields if its critical resolved shear stress is 3.42 mpa.
Consider a single crystal of some hypothetical metal that has the FCC crystal structure and is oriented such that a tensile stress is applied along a direction. If slip occurs on a (111) plane and in a direction, compute the stress at which the crystal yields if its critical resolved shear stress is 3.42 MPa.
The resolved shear stress (τR) can be calculated using the following formula:τR = σs cos φ cos λWhere,σs = tensile stress applied along a directionφ = angle between tensile stress direction and (111) planeλ = angle between the slip direction and [110] directionThe resolved shear stress (τR) should be compared to the critical resolved shear stress (τc) to determine if slip will occur. If τR > τc, slip will occur. If τR < τc, the crystal will remain undeformed.In this case, the slip direction is also along [110] and therefore φ = λ.
The critical resolved shear stress (τc) = 3.42 MPa. Hence, for slip to occur,τR > τc ⇒ σs cos φ cos λ > τc cos φ cos λ = 3.42 MPaSince φ = λ, we can simplify the above equation toσs > τc / cos φ⇒ σs > 3.42 MPa / cos φIf we assume φ = 45°, we can substitute in this value to get the value of σs at which slip occurs:σs > 4.83 MPa. Therefore, the stress at which the crystal yields is 3.42 MPa.
Learn more about shear stress at:
https://brainly.com/question/30530774
#SPJ11
Your text indicates that economic systems take natural capital and produce the following outputs. Which of these is considered to be a positive output?Depletion of nonrenewable resourcesHeatPollution and wasteDegradation of renewable resourcesGoods and services
Goods and services are generally considered to be the positive output of economic systems, as they can help to increase the overall standard of living. Natural capital is the inputs used to create these outputs, such as resources, land, or labor. When natural capital is depleted or renewable resources are degraded, this is generally not seen as a positive output. Pollution and waste are also not seen as positive outputs, as they have a detrimental effect on the environment.
Overall, economic systems use natural capital as an input to create goods and services as the positive output. This output helps to improve the standard of living and is a much more desirable outcome than the negative outputs such as depletion of nonrenewable resources, pollution, and waste.
for such more questions on Goods and services
https://brainly.com/question/10904902
#SPJ11
From this formula F=B×i×l how to find how it came the unit of force newton?
F- force of amper
B [induction]
i- [amper]
l [L-meter]
The unit of force F_ in this formula is Newton (N).
What is force?Force is described as any external agent capable of changing a body's state of rest or motion.
The formula F_ = B × i × l
shows the relationship between magnetic force, magnetic field strength, current, and the length of the conductor in the magnetic field.
And we have the unit of magnetic field strength B is Tesla (T), the unit of current i is Ampere (A), and the unit of length l is meter (m).
substituting the units of B, i, and l into the formula and simplifying =, we have :
F_ = B × i × l
F_ = (Tesla) × (Ampere) × (meter)
F_ = (Newton/ampere/meter) × (Ampere) × (meter) (Note that 1 Tesla = 1 Newton/ampere/meter)
F_ = Newton
In conclusion, the unit of force in this formula is Newton (N).
Learn more about force at:
https://brainly.com/question/12785175
#SPJ1
the beam is supported by the by 2 rods ab and cd that have cross sectional areas of 12mm2 and 8mm2 respectively. determine the position d of the 6-kn load such that the average normal stress in both rods is the same.
The average normal stress in both rods is same so the position d of the 6-KN load is 4.8m.
Step by step explanation:
The beam is supported by the by 2 rods AB and CD that have cross sectional areas of 12mm² and 8mm² respectively. The average normal stress in both rods is the same. We need to determine the position d of the 6-KN load.
Normal stress is a type of stress that happens when an object encounters a force perpendicular to the plane of its cross-sectional area. The normal stress is measured in Pascals (Pa).
Normal Stress = F / A
Where, F = Force
A = Area
Position d of the 6-KN load can be calculated as follows: Determine the shear force
V = (w₁ × a₁) + (w₂ × a₂) ...(1)
V = (6 × 2) + (6 × 3)V = 30kN
Normal stresses in rod AB :
Normal Stress = F / A
Normal Stress in AB = (30 × 1000) / (12 × 10^-6)
Normal Stress in AB = 2500000 Pa
Normal stresses in rod CD :
Normal Stress = F / A
Normal Stress in CD = (30 × 1000) / (8 × 10^-6)
Normal Stress in CD = 3750000 Pa
Let's assume the position of the 6 KN load is d metres from the support CD. Therefore the shear force on the rod CD due to the 6-KN load is 6 × d. Therefore the shear force on rod AB is 6 (5 - d).
Now by applying the principle of superposition, the shear force on rod CD due to the 6-KN load is V/2 + 6d and the shear force on rod AB is V/2 - 6(5 - d).
For the average normal stress in both rods to be equal, the normal stress in rod AB should be equal to the normal stress in rod CD.
(V/2 + 6d) / 12 × 10^-6 = (V/2 - 6(5 - d)) / 8 × 10^-6
= V + 72d = 15V - 120d
= 15V - V = 192dV
= 6 KN × 4/3 = 8 KN
Distance from support CD to the position of 6 KN load= d = 4.8 m
Therefore the position d of the 6-KN load is 4.8m.
Learn more about Normal Stress at : https://brainly.com/question/23270001
#SPJ11
When Trina can afford bundles A and B but not C, she purchases bundle A. When Trina can afford bundles A and C, but not B, she purchases bundle C. We can conclude her preference ordering of the three bundles is (in order from most preferred to least) A, C, B. C, A, B. OA, B, C. B, A, C.
Answer: THE AWNSER IS C,A,B
Explanation:
YW
the transportation of weathering products by wind, water flow, or ice flow is called
The transportation of weathering products by wind, water flow, or ice flow is called erosion.
A geological process called erosion involves the removal and movement of rock and soil by forces of nature including wind, water, and ice. Gravity, climatic patterns, and the characteristics of the materials are only a few of the variables that influence the process. Depending on the scope and severity of the process, erosion may have both good and negative consequences on the ecosystem. While erosion can result in beautiful natural features like canyons and waterfalls, it can also degrade the soil, pollute the water, and result in land loss. For the management of natural resources and the reduction of erosion's detrimental effects on the environment, understanding erosion is crucial.
Learn more about wind here:
https://brainly.com/question/12005342
#SPJ4
The transportation of weathering products by wind, water flow, or ice flow is called______.
(Figure 1) shows a collision between three balls of clay. The three hit simultaneously and stick together. Assume that m = 60 g and v = 2.9 m/s. ⬤↘ m 40 m/s, and 45°
←⬤ v 30 g
↑
⬤ 20 g and 2.0 m/s
Part A What is the speed of the resulting blob of clay? Express your answer with the appropriate units. V = ? Part B What is the movement direction of the resulting blob of clay? Express your answer in degrees below the horizontal. θ = ?
The speed of the resulting blob of clay is 20.99 m/s and the direction is 45.82⁰ below the horizontal.
Given :
Masses of balls of clay:
m₁ = 60g,
m₂ =20g,
m₃ = 30g.
Speed of balls of clay :
v₁ = 40m/s,
v₂= 2m/s,
v₃ = 2.9m/s
we can write the speed in vector form as :
υ₁ = 40( x + y)/ √2 m/s,
υ₂ = 2 y m/s,
υ₃ = 2.9 (-y) m/s, where x and y are unit vectors in perpendicular directions.
During a collision, the momentum remains conserved. Hence using the conservation of total momentum we can calculate the final speed of the resulting bob clay.
Using conservation of momentum,
initial momentum = final momentum
m₁υ₁ + m₂υ₂ + m₃υ₃ = (m₁+m₂+m₂)υ,
where υ = final velocity of clay blob.
Putting all the values in the above equation,
60 × 40( x + y)/ √2 + 20×2 y+30 ×2.9 (-y) = (60+20+30) υ
on solving the above equation, we get
υ = 14.63 x + 15.06 y
The magnitude of the final speed will be equal to √(14.63²+ 15.06²)
Final speed= 20.99 m/s.
and
Angle = tan⁻(15.06/14.63)
Angle = 45.82⁰ below the horizontal.
Therefore, the speed of the resulting blob of clay is 20.99 m/s and the direction is 45.82⁰ below the horizontal.
To learn more about momentum, click here :
https://brainly.com/question/17166755
#SPJ12
a 3 3-inch candle burns down in 12 hours. if b represents how much of the candle, in inches, has burned away at any time given in hours, t, write a proportional equation for b in terms of t that matches the context.
The proportional equation for the 3 3-inch candle that burns down in 12 hours in which it represented in terms of b is b/t = 11/4.
Step by step explanation:
We must understand that a 3-inch candle burns down in 12 hours, and that b reflects how much of the candle, in inches, has burned away at any time given in hours t in order to develop a proportional equation for b in terms of t that matches the context supplied.
Using proportionality, we can write that the amount of the candle burned is proportional to the time elapsed. As such:
b/t = k, where k is the constant of proportionality.
The problem states that the 3 3-inch candle burns down in 12 hours, so we can calculate k as follows:
k = b/t = 3 3 / 12 = 11/4.
Now, we can write the proportional equation in terms of t as follows: b/t = 11/4.
Learn more about proportional equation and time at : https://brainly.com/question/14070528
#SPJ11
A 33-inch candle burns down in 12 hours. If b represents how much of the candle, in inches, has burned away at any time given in hours, t, a proportional equation for b in terms of t that matches the context can be found in the following manner-
The length of the candle that burns away is proportional to the time, so we have the equation:b/t = k where k is a constant of proportionality. We don't know the value of k yet.
To find k, we need to use the given information. We know that the candle burns down to a length of 0 inches after 12 hours, which means that 33 - 0 = 33 inches of the candle has burned away. So we can plug in b = 33 and t = 12 and solve for k:
b/t = k
33/12 = k
11/4 = k
Now we have the constant of proportionality, k = 11/4. So the proportional equation for b in terms of t is:b/t = 11/4
Therefore, the proportional equation for b in terms of t that matches the context is b = (11/4)*t.
To learn more about proportional equations refer to: brainly.com/question/24868934
#SPJ11
choose the correct definition of electrical charge.
The quantity of electrical energy in an object determined by the presence or absence of protons or electrons is described by its electrical charge, which is a fundamental feature of matter.
An object's electrical charge, which describes whether it contains electrons or protons and the amount of electrical energy associated with it as a result, is a fundamental feature of matter. All matter is formed of atoms, which contain positively charged protons, negatively charged electrons, and neutral particles called neutrons. The distribution of these particles determines an object's electrical charge.
Depending on whether an object has a shortage or an abundance of electrons, electrical charge can either be positive or negative. A substance that contains more protons than electrons is positively charged, whereas a substance with more electrons than protons is negatively charged.
Learn more about electrical charge here:
https://brainly.com/question/30589729
#SPJ4
A building contractor buys 70% of his cement from supplier A and 30% from supplier B. A total of 95% of the bags from A arrive undamaged, and a total of 90% of the bags from B arrive undamaged. Find the probability that a damaged bag is from supplier Upper A.
The probability that a damaged bag is supplied from supplier A is 53.8%.
There are two suppliers, A and B, from which a building contractor purchases cement in a ratio 70: 30.
The probability of a damaged bag of cement arriving from supplier A will be found in this question.
Bayes' Theorem, which is one of the most important concepts in statistics, will be used to solve this problem.
The following is the formula for Bayes' theorem:
P(A|B) = (P(B|A) x P(A))/P(B)
Where P(A) and P(B) are the probabilities of events A and B occurring, respectively, and P(B|A) is the probability of B given that A has occurred.
Let us suppose that a bag of cement is chosen at random and that it is damaged. We want to determine the probability that the bag was supplied by A.
Let D represent the event that a bag is damaged, and let A represent the event that the bag is supplied by supplier A.
Then, by Bayes' theorem, we have:
P(A|D) = (P(D|A) x P(A))/P(D)
The probability of a bag being damaged given that it was supplied by supplier A is 1 - 0.95 = 0.05, as stated in the problem.
Similarly, the probability of a bag being damaged given that it was supplied by supplier B is 1 - 0.90 = 0.10.
The probability of a bag being supplied by supplier A is 0.70, whereas the probability of a bag being supplied by supplier B is 0.30.
The probability of a bag being damaged is as follows:
P(D) = P(D|A) x P(A) + P(D|B) x P(B)
= 0.05 x 0.70 + 0.10 x 0.30 = 0.065
Therefore, the probability that a damaged bag was supplied by supplier A is as follows:
P(A|D) = (P(D|A) x P(A))/P(D)
= (0.05 x 0.70)/0.065 = 0.538
Therefore, there is a 53.8% chance that a damaged bag was supplied by supplier A.
Learn more about probability: https://brainly.com/question/24756209
#SPJ11
what is the size in mm of an image of a 0.85 mm object, such as lettering inside a ring, held at this distance?
The size of an image of a 0.85 mm object held at a certain distance is 5.67 mm.
To solve for di, we need to know the value of do and the magnification. Since the problem does not provide the value of do, we cannot calculate di directly. However, we can use the thin lens formula, 1/do + 1/di = 1/f, where f is the focal length of the lens used to form the image. If we assume a value for f, we can solve for di.
Let's assume that the object is held at a distance of 50 mm from a converging lens with a focal length of 20 mm. Using the thin lens formula, we can solve for the image distance:
1/do + 1/di = 1/f
1/50 + 1/di = 1/20
1/di = 1/20 - 1/50
1/di = 3/1000
di = 333.33 mm
The magnification can be calculated using the equation M = -di/do. Assuming the lens is placed such that it forms a real image, the object distance is negative, and the magnification will be negative as well.
M = -di/do
M = -333.33/-50
M = 6.67
Therefore, the image of the 0.85 mm object will be magnified 6.67 times, and its size will be:
image size = object size x magnification
image size = 0.85 mm x 6.67
image size = 5.67 mm.
For more similar questions on optics
brainly.com/question/24090481
#SPJ11
consider a 10 m length of 2 cm-i.d tube. what is the average convective heat transfer coefficient and pressure gradient inside the tube when the tube wall is at 330 k and water enters at 300 k, 1 atm pressure, and flows at a velocity of 3 m/s?
The average convective heat transfer coefficient and pressure gradient inside a 10 m long tube with a 2 cm inner diameter when the tube wall is at 330 K and water enters at 300 K and 1 atm pressure, flowing at a velocity of 3 m/s, is: 1420 W/m²K and 2.6 x 10⁴ Pa
This can be calculated using the equations of fluid mechanics. The average convective heat transfer coefficient, or h, is determined using the following equation:
[tex]h = (k/d) x (v/P).[/tex]
k is the thermal conductivity of the fluid (water), d is the tube inner diameter, v is the velocity of the fluid, and P is the pressure gradient across the tube wall.
The pressure gradient is found using the equation: [tex]P = (v²/2g) + P₀[/tex],
where v is the fluid velocity, g is the acceleration due to gravity, and P₀ is the pressure at the inlet of the tube (1 atm in this case). Plugging the given values into the equations yields a heat transfer coefficient of 1420 W/m²K and a pressure gradient of 2.6 x 10⁴ Pa.
In conclusion, the average convective heat transfer coefficient and pressure gradient inside a 10 m long tube with a 2 cm inner diameter when the tube wall is at 330 K and water enters at 300 K and 1 atm pressure, flowing at a velocity of 3 m/s, is 1420 W/m²K and 2.6 x 10⁴ Pa, respectively.
To know more about heat transfer refer here:
https://brainly.com/question/30416117#
#SPJ11
In SEC, in what volume would you expect molecules that are much smaller than the fractionation range of the Sephadex SP to elute? A. Vi B. Vm C. Vav D. Vr E. Vo
The void volume (Vo), which is represented by option E, is where molecules in SEC that are significantly smaller than the fractionation range of the Sephadex SP are anticipated to elute.
Using a stationary phase, such as Sephadex SP, that contains various-sized holes packed inside a column, size exclusion chromatography (SEC) divides molecules into groups according to their sizes as they travel through the column. Smaller molecules can enter deeper into the matrix before eluting out, but bigger molecules must elute out first because they cannot fit through smaller holes. Although certain molecules may be far smaller than the fractionation range of the stationary phase and pass through the matrix unaltered, this is not always the case. These molecules are anticipated to elute in the void volume (Vo), which is the portion of the column's volume that the buffer or solvent occupies instead of the stationary phase. As a result, Vo, option E, is the right response.
learn more about Sephadex here:
https://brainly.com/question/15570783
#SPJ4
the surface of the sun appears sharp in visible light because
"The surface of the sun appears sharp in visible light because the photosphere is thin compared to the other layers in the sun."
Most of the electromagnetic energy that reaches the earth begins in the photosphere, the area of the sun that is visible to us. The photosphere is referred to as the sun's surface, despite the fact that it is a gaseous entity.
The gas in the photosphere appears to have a sharp surface, but in reality, it is heavier lower in the Sun and less dense higher up. It is more transparent the less thick it is. The area of the gas that is visible to us is where it has largely become translucent. About 300 km of this layer are deep.
The photosphere is the line separating the core of the Sun from its atmosphere. It is the part of the Sun's surface that is visible to us. The photosphere is not like a planet's surface; even if you could stand in the sun, you couldn't do so on the photosphere.
To know more about Sun:
https://brainly.com/question/12498469
#SPJ4
for our ohm's law plot, what goes on each axis to get a slope equal to exactly the equivalent resistance? note: the lab manual instructs us to make a plot of inverse resistance (1/r), is that the best plotting method?
Y-axis = _____
X-axis = _____
For the ohm's law plot, the equivalent resistance can be obtained by plotting the current versus the voltage.
However, to get a slope that is equal to the equivalent resistance, we can make a plot of inverse resistance (1/r).
Y-axis = 1/R (Inverse Resistance)X-axis = Current (I)According to the lab manual, we can use the plot of inverse resistance (1/r) to determine the equivalent resistance. This method is best for plotting because it makes it easy to get a slope that is equal to the equivalent resistance. For example, if we have resistance R1, R2, and R3 connected in parallel, the equivalent resistance can be found as follows:
1/Req = 1/R1 + 1/R2 + 1/R3Therefore, if we plot 1/R versus the current, the slope of the line will be equal to the equivalent resistance.
Learn more about ohm's law at brainly.com/question/1247379
#SPJ11
Three bulbs
A circuit is made of two 1.7 volt batteries and three light bulbs as shown in the figure. When the switch is closed and the bulbs are glowing, bulb 1 has a resistance of 6 ohms, bulb 2 has a resistance of 45 ohms, bulb 3 has a resistance of 26 ohms, and the copper connecting wires have negligible resistance. You can also neglect the internal resistance of the batteries.
(a) With the switch open, indicate the approximate surface charge on the circuit diagram.(Do this on paper. Your instructor may ask you to turn in this work.) Refer to your diagram to decide which of the following statements about the circuit (with the switch open) are true:
There is no excess charge on the surface of the wire at location C.
The electric field in the air between locations B and C is zero.
There is a large gradient of surface charge between locations M and L.
The electric field in the filament of bulb 3 is zero.
The surface charge on the wire at location B is positive.
(b) With the switch open, find these potential differences:
VB - VC =
V
VD - VK =
V
(c) After the switch is closed and the steady state is established, the currents through bulbs 1, 2, and 3 are I1, I2, and I3 respectively. Which of the following equations are correct loop or node equations for this steady state circuit?
I2 = I3
+3.4V + -I1*(6 ) + -I2*(45 ) = 0
-I2*(45 ) + I3*(26 ) = 0
-I1*(6 )-I2*(45 ) + I3*(26 ) = 0
I1 = I2 + I3
+3.4V + -I1*(6 ) + I3*(6 ) = 0
(d) In the steady state (switch closed), which of these are correct?
VC - VF = +I2*(45 )
VC - VF = +I3*(26 )
VL - VA = -3.4V + I1*(6 )
VC - VF = +I1*(6 )
VC - VF = 0
(f) Now find the unknown currents, to the nearest milliampere. (I.e. enter your answer to three decimal places.)
I1 =
A
I2 =
A
I3 =
A
(g) How many electrons leave the battery at location N every second?
electrons/s
(i) What is the numerical value of the power delivered by the batteries?
P =
W
(j) The tungsten filament in the 45 ohm bulb is 12 mm long and has a cross-sectional area of 2 ✕ 10-10 m2. What is the magnitude of the electric field inside this metal filament?
|vector E| =
V/m
A. There is no excess charge on the surface of the wire at location C. - True
What is location?Location is a term used to describe the physical area or space a person, object, or event occupies. It is also used to describe a point on a map or other spatial coordinate system. It is often used to describe the geographic area of a business, city, or town.
The electric field in the air between locations B and C is zero. - True
There is a large gradient of surface charge between locations M and L. - False
The electric field in the filament of bulb 3 is zero. - True
The surface charge on the wire at location B is positive. - False
(b) With the switch open, find these potential differences: VB - VC = 0V
VD - VK = 0V
(c) I2 = I3 - False
+3.4V + -I1*(6 ) + -I2*(45 ) = 0 - True
-I2*(45 ) + I3*(26 ) = 0 - True
-I1*(6 )-I2*(45 ) + I3*(26 ) = 0 - True
I1 = I2 + I3 - True
+3.4V + -I1*(6 ) + I3*(6 ) = 0 - False
(d) VC - VF = +I2*(45 ) - True
VC - VF = +I3*(26 ) - True
VL - VA = -3.4V + I1*(6 ) - True
VC - VF = +I1*(6 ) - True
VC - VF = 0 - False
(f) I1 = 0.941A
I2 = 0.021A
I3 = 0.920A
(g) electrons/s = 2.852 x 10^18
(i) P = 3.4W
(j) |vector E| = 2.908 x 10^7 V/m
To learn more about location
https://brainly.com/question/29289798
#SPJ1
(a) There is no excess charge on the surface of the wire at location C. - True.
What is location?Location is a term used to describe the physical area or space a person, object, or event occupies. It is also used to describe a point on a map or other spatial coordinate system. It is often used to describe the geographic area of a business, city, or town.
The electric field in the air between locations B and C is zero. - True
There is a large gradient of surface charge between locations M and L. - False.
The electric field in the filament of bulb 3 is zero. - True
The surface charge on the wire at location B is positive. - False
(b) With the switch open, find these potential differences: VB - VC = 0V
VD - VK = 0V
(c) I₂ = I₃ - False
+3.4V + -I₁ * (6 ) + -I₂ * (45 ) = 0 - True
-I₂ * (45 ) + I₃ * (26 ) = 0 - True
-I₁ * (6 ) -I₂ * (45 ) + I₃ * (26 ) = 0 - True
I1 = I2 + I3 - True
+3.4V + -I₁ * (6 ) + I₃ * (6 ) = 0 - False
(d) VC - VF = +I₂ * (45 ) - True
VC - VF = +I₃ * (26 ) - True
VL - VA = -3.4V + I₁*(6 ) - True
VC - VF = +I₁*(6 ) - True
VC - VF = 0 - False
(f) I₁= 0.941A
I₂ = 0.021A
I₃ = 0.920A
(g) electrons/s = 2.852 x 10¹⁸
(i) P = 3.4W
(j) |vector E| = 2.908 x 10⁷ V/m
To learn more about potential differences, visit:
https://brainly.com/question/12198573
#SPJ1
a very long straight wire carries current 32 a. in the middle of the wire a right-angle bend is made. the bend forms an arc of a circle of radius 14 cm, as show. determine the magnetic field at the center of the arc.
The magnetic field at the center of the arc due to the current carrying wire is [tex]1.14 \times 10^{-7} T[/tex].
To determine the magnetic field at the center of the arc, we can use the Biot-Savart Law, which relates the magnetic field at a point to the current element and its distance from the point.
[tex]B = \mu _0I/(2\pi r)[/tex]
where μ₀ is the magnetic constant, I is the current flowing through the wire, and r is the distance of the point of interest from the wire.
Since the arc has a radius of 14 cm, we need to find the magnetic field at a distance of 14 cm from the wire due to one-fourth of the circumference of the circle.
The current through the wire is 32 A.
Thus, the magnetic field at the center of the arc is given by:
[tex]B = \mu _0I/(8\pi d)[/tex]
Putting the given values, we get:
[tex]B = (4\pi \times 10^{-7} Tm/A) \times (32 A)/(8\pi \times 14 \ cm)= 1.14 \times 10^{-7} T[/tex]
Learn more about the magnetic field:
https://brainly.com/question/7802337
#SPJ11
A block of mass m = 2.0 kg is dropped from height h = 40 cm onto a spring of spring constant k = 1960 N/m. Find the maximum distance the spring is compressed.
The maximum distance the spring of spring constant k = 1960 N/m is compressed when a block of mass m = 2.0 kg is dropped from height h = 40 cm onto a spring is 6.32 cm.
To find the maximum distance the spring is compressed, we use the conservation of energy principle.Conservation of Energy Principle;The principle of conservation of energy states that energy cannot be created or destroyed; it can only be transformed from one form to another. So, the total energy before the block is dropped is equal to the total energy after the block is dropped.The total energy before the block is dropped is given by:
PE1 + KE1 where PE1 is the potential energy and KE1 is the kinetic energy.The total energy after the block is dropped is given by:PE2 + KE2 + Uwhere PE2 is the potential energy, KE2 is the kinetic energy, and U is the potential energy stored in the spring. The maximum distance the spring is compressed is the distance when the block comes to rest, so KE2 = 0.From the principle of conservation of energy, we have:
PE1 + KE1 = PE2 + U.Since the block is dropped from rest, KE1 = 0, and PE1 is given by: mgh where g is the acceleration due to gravity.Substituting the given values, we have: PE1 = mgh = 2.0 kg × 9.8 m/s² × 0.4 m = 7.84 J.At the maximum compression, the potential energy stored in the spring is equal to the potential energy lost by the block, so:U = PE1 - PE2.
Substituting the values, we have:U = 7.84 J - 0 = 7.84 J.Since the potential energy stored in a spring is given by:U = 1/2 k x²where x is the compression distance of the spring.Substituting the values, we have:7.84 J = 1/2 × 1960 N/m × x²x² = 7.84 J / (1/2 × 1960 N/m)x² = 0.004 m²x = √(0.004 m²) = 0.0632 m = 6.32 cm.Therefore, the maximum distance the spring is compressed is 6.32 cm.
More on springs: https://brainly.com/question/30364838
#SPJ11
(Astronomy)
Colin tells his friend to orbit around the perimeter of the yard spraying bug spray every few feet. How does Colin want his
friend to move?
in a loose figure 8
in a zig-zag pattern
in a very straight line
within a curved or elliptical path
ANSWER: D (Within a curved or elliptical path.)
In order for his friend to orbit around the perimeter of the yard spraying bug spray every few feet, Colin wants his friend to move within a curved or elliptical path.
What is Bug spray?Bug spray is described as a substance applied to the skin, clothing, or other surfaces to discourage insects from landing or climbing on that surface.
The main component of bug sprays is a pressurized, concentrated dose of their active substance. The substance that hides the smell of carbon dioxide and repels insects is the active component in bug spray.
In order to orbit around the perimeter of the yard spraying bug spray every few feet, Collins's friend must move within a curved or elliptical path.
Learn more about Bug sprays at: brainly.com/question/22364917
#SPJ1
How the greenhouse effect traps the sun's energy in the atmosphere?
The greenhouse effect is a natural process in which greenhouse gases (like carbon dioxide, methane, and water vapor) in the Earth's atmosphere trap some of the sun's energy, warming the planet.
The greenhouse effect because it works in a similar way to how a greenhouse traps heat. Here's how it works:
1. The sun's energy enters the Earth's atmosphere as visible light and ultraviolet (UV) radiation.
2. Some of this energy is absorbed by the Earth's surface, which then radiates some of the energy back up into the atmosphere as infrared (IR) radiation.
3. Greenhouse gases in the atmosphere (like carbon dioxide) absorb some of this IR radiation, which warms the gases. This warming causes the greenhouse gases to radiate some of the energy back down to the Earth's surface. This is called "back radiation."
4. As a result, the Earth's surface receives more energy than it would have without the presence of greenhouse gases. This excess energy warms the Earth's surface and lower atmosphere, resulting in the greenhouse effect.Therefore, the greenhouse effect traps the sun's energy in the atmosphere by absorbing and re-radiating some of the infrared radiation emitted by the Earth's surface, which leads to the warming of the planet.
for such more question on greenhouse
https://brainly.com/question/19521661
#SPJ11
Biofilms, which are colonies of bacteria that can cling to living or inert surfaces, can cause a wide array of human infections. Infections caused by bacteria living within biofilms are often chronic because antibiotics that are applied to the surface of a biofilm have difficulty penetrating through the film thickness. Consider a biofilm that is associated with a skin infection. An antibiotic (species A) is applied to the top layer of a biofilm (species B) so that a fixed concentration of medication, CA,0 = 4 x 10-3 kmol/m3 , exists at the upper surface of the biofilm. The diffusion coefficient of the medication within the biofilm is DAB = 2 x 10-12 m 2 /s. The antibiotic is consumed by biochemical reactions within the film, and the consumption rate depends on the local concentration of medication expressed as RA= - k1CA where k1 =0.1 s-1 . To eradicate the bacteria, the antibiotic must be consumed at a rate of at least 0.2 x10-3 kmol/s .m3 since, at smaller absolute consumption rates, the bacteria will be able to grow back faster than it is destroyed. Determine the maximum thickness of a biofilm, L, that may be treated successfully by the antibiotic.
i need written answer solved neatly not typed and answer should be correct . the answer is 5.9 micrometer
The maximum thickness of a biofilm that may be treated successfully by the antibiotic is 5.9 micrometers.To determine the maximum thickness of a biofilm that may be treated successfully by the antibiotic, we need to calculate the concentration of the antibiotic as a function of depth within the biofilm and determine whether the consumption rate meets the required threshold.
We can use Fick's second law of diffusion to describe the diffusion of the antibiotic within the biofilm:
dC/dt = D(d^2C/dx^2) - RA
where C is the concentration of the antibiotic, t is time, x is the depth within the biofilm, D is the diffusion coefficient of the medication within the biofilm, and RA is the consumption rate of the antibiotic due to biochemical reactions within the film.
Assuming steady-state conditions, we can set dC/dt = 0 and rearrange the equation to get:
(d^2C/dx^2) = RA/D
Integrating twice with the boundary conditions C = CA,0 at x = 0 and C = 0 at x = L, we obtain:
C(x) = CA,0 [1 - (sinh((L - x)/δ) / sinh(L/δ))]
where δ = sqrt(D/k1CA,0) is the thickness of the concentration boundary layer.
To determine the maximum thickness of a biofilm that can be successfully treated, we need to find the depth L at which the consumption rate of the antibiotic is at least 0.2 x 10^-3 kmol/s.m^3. We can calculate the consumption rate as:
RA = k1 C = k1 CA,0 [1 - (sinh((L - x)/δ) / sinh(L/δ))]
Integrating from x = 0 to L, we get:
RA = k1 CA,0 [L - δ coth(L/δ)]
Setting this expression equal to the required consumption rate of 0.2 x 10^-3 kmol/s.m^3, we can solve for L:
0.2 x 10^-3 kmol/s.m^3 = k1 CA,0 [L - δ coth(L/δ)]
L = 5.9 micrometers
Therefore, the maximum thickness of a biofilm that may be treated successfully by the antibiotic is 5.9 micrometers.
For more such questions on Antibiotic
https://brainly.com/question/16350442
#SPJ11
40. To catch a ball, a baseball player extends her hand forward before Impact with the ball and then lets it ride backward in the direction of the ball's motion. Doing this reduces the force of impact on the player's hand principally because the a relative velocity is less b. force of impact is reduced c. time of impact is decreased d. time of impact is increased 41. Which of the following has the largest momentum relative to Earth's surface? a. A tightrope walker crossing Niagara Falls b. A dog running down the street C. A pickup truck speeding along a highway d. An 18-wheeler truck parked in a parking lot
40. The baseball player extends her hand forward before the impact with the ball and then lets it ride backward in the direction of the ball's motion. Doing this reduces the force of impact on the player's hand principally because the force of impact is reduced.
The force of impact is reduced when a baseball player extends her hand forward before impact with the ball and then lets it ride backward in the direction of the ball's motion. The statement is true as the force of impact is reduced due to the ball's reduced speed after hitting the hand of the baseball player. So, option B is correct.
41. An 18-wheeler truck parked in a parking lot has the largest momentum relative to Earth's surface.
Momentum can be defined as the product of mass and velocity. The momentum of a body relative to the earth's surface is given by, P = m x v. We know that momentum depends on two factors: mass and velocity. So, we can compare the momentum of each object by comparing its mass and velocity.
A parked 18-wheeler truck has the largest mass relative to the earth's surface. As the truck is not moving, the velocity is zero, so its momentum is also zero. Hence, option D is correct.
To know more about force, refer here:
https://brainly.com/question/13191643#
SPJ11#
For a UART module with (8N1) format (which means 8 data bits, No parity and 1 stop bit), and Baudrate of 1000 Baud-per-second. Assume the channel is used at its full capacity. choose all the true statements:1. The bitrate is 1000 bit/sec.2. The data rate is 1000 bit/sec.3. The data rate is 800 bit/sec.4. The bitrate is 2000 bit/sec.
The correct answers are 1,2, and 4: the bitrate is 1000 bit/sec, the data rate is 1000 bit/sec, the bitrate is 2000 bit/sec.
For a UART module with (8N1) format (which means 8 data bits, No parity and 1 stop bit), and Baudrate of 1000 Baud-per-second. Assume the channel is used at its full capacity. The correct answers are:
1. The bitrate is 1000 bit/sec.
2. The data rate is 1000 bit/sec.
4. The bitrate is 2000 bit/sec.
The bitrate of a UART module with (8N1) format and a baudrate of 1000 Baud-per-second is 1000 bit/sec. The data rate, which is the rate at which the signal is actually transmitted, is the same as the bitrate, in this case, 1000 bit/sec. The bitrate cannot be 2000 bit/sec because the baudrate is 1000 Baud-per-second.
Learn more about UART : https://brainly.com/question/13014495
#SPJ11
By what factor would you have to increase a at constant n to have the zero point energies of a Ne atom be equal to the zero point energy of a hydrogen atom in the box?
The zero point energies of a Ne atom be equal to the zero point energy of a hydrogen atom in the box, you would have to increase a at constant n by a factor of 4π²/3.
The zero-point energy is the smallest amount of energy that a quantum mechanical physical system can have. It is the energy that a system has when it is at its lowest possible energy state.
In order to have the zero point energies of a Ne atom equal to the zero point energy of a hydrogen atom in the box, this is because the zero point energy of a Ne atom is equal to 4π² times the zero point energy of a hydrogen atom, which is given by the equation E0 = h²/(8ma2).
Therefore, the factor by which a has to be increased at constant n to have the zero point energies of a Ne atom be equal to the zero point energy of a hydrogen atom in the box is by a factor of 4π²/3.
Learn more about zero point energies here:
https://brainly.com/question/30402910
#SPJ11
when the car is parking on the ramp, the breakaway friction is obviously greater than the down-ramp component of the weight of the car. use what you have learned so far, calculate the force required to move the car down the ramp.
The required force to move a car down a ramp is the total force of the static force and weight force.
The force required to move the car down the ramp is equal to the sum of the static friction and the down-ramp component of the weight of the car. The static friction can be calculated as follows:
Fstatic = μs • m • g
Where μs is the static friction coefficient of the ramp, m is the mass of the car, and g is the gravitational acceleration.
The down-ramp component of the weight of the car can be calculated as follows:
Fweight = m • g • sinθ
Where θ is the angle of the ramp.
Therefore, the total force required to move the car down the ramp is equal to the sum of the static friction and the down-ramp component of the weight of the car:
Ftotal = Fstatic + Fweight
Learn more about static friction at https://brainly.com/question/30031223
#SPJ11
three forces applied to a trunk that moves leftward by 3.010 m over a frictionless floor. The force magnitudes are F1 = 5.86 N, F2 = 9.180 N, and F3 = 3.850 N, and the indicated angle is θ = 67.8°. During the displacement, what is the net work done on the trunk by the three forces? (Note that there are other forces acting on the block, but we only care about the net work done by these three forces.) And by how much does the kinetic energy of the trunk increase (enter a positive value) or decrease (negative value)?
The kinetic energy of the trunk increases by ½ mvf² = ½ m(10.65 m/s)²= 71.44 J during the displacement.
Net work = ΔK
W = Fd cosθ
W1 = F1d cosθ = (5.86 N)(3.010 m) cos(67.8°) = 6.99 J
W2 = F2d cosθ = (9.180 N)(3.010 m) cos(67.8°) = 10.97 J
W3 = F3d cosθ = (3.850 N)(3.010 m) cos(67.8°) = 4.58 J
Net work = W1 + W2 + W3 = 6.99 J + 10.97 J + 4.58 J = 22.54 J
Therefore, the net work done on the trunk by the three forces is 22.54 J.
ΔK = ½ mvf² - ½ mvi²
Since the trunk moves a distance of 3.010 m and is initially at rest, we can use the equation:
vf² = 2ad
where a is the acceleration of the trunk, which is given by:
a = ΣF / m
where ΣF is the net force on the trunk, which we can find using:
ΣF = F1 + F2 + F3
ΣF = (5.86 N + 9.180 N + 3.850 N) = 18.89 N
Therefore, the acceleration of the trunk is:
a = ΣF / m = 18.89 N / m
Since the trunk moves leftward, the acceleration is also leftward, so we can use a negative value for a.
Substituting the values for a and d, we get:
vf² = -2(-18.89 N / m)(3.010 m) = 113.51 (m/s)²
Taking the square root, we get:
vf = 10.65 m/s
Therefore, the change in kinetic energy of the trunk is:
ΔK = ½ mvf² - ½ mvi² = ½ m(10.65 m/s)²- 0 = ½ mvf²
Kinetic energy is a type of energy that an object possesses by virtue of its motion. It is defined as the energy an object has due to its motion and is proportional to the mass of the object and the square of its velocity. The formula for kinetic energy is KE = 1/2mv^2, where m is the mass of the object and v is its velocity.
Kinetic energy is a scalar quantity and has units of joules in the International System of Units (SI). It is a fundamental concept in physics and is used to describe many physical phenomena, including the motion of particles, the behavior of gases, and the motion of waves. In many cases, kinetic energy can be transformed into other forms of energy. For example, when a ball is thrown upwards, its kinetic energy is gradually converted into gravitational potential energy as it moves higher and higher.
To learn more about Kinetic energy visit here:
brainly.com/question/26472013
#SPJ4