during a physics experiment, helium gas is cooled to a temperature of 13.0 k at a pressure of 9.00×10−2 atm.

(a) The gauge pressure in the jar is equal to the pressure difference, so the gauge pressure in the jar is 27.4 kPa.

(b) The absolute pressure in the jar is 128.7 kPa.

(a) To find the gauge pressure in the jar, we need to use the relationship between the pressure difference and the height difference of the mercury in the manometer. The pressure difference between the jar and the atmosphere is equal to the difference in heights of the mercury columns. We can use the following formula:

ΔP = ρgh

where ΔP is the pressure difference, ρ is the density of the mercury, g is the acceleration due to gravity, and h is the height difference of the mercury columns.

In this case, the height difference is 20.6 cm, and the density of the mercury is 13.5 g/cm³. The acceleration due to gravity is 9.81 m/s². Converting the height to meters, we get:

h = 0.206 m

Substituting the values, we get:

ΔP = (13.5 g/cm³) × (9.81 m/s²) × (0.206 m) = 27.4 kPa

The gauge pressure in the jar is equal to the pressure difference, so the gauge pressure in the jar is 27.4 kPa.

(b) The absolute pressure in the jar is equal to the sum of the gauge pressure and the atmospheric pressure. The atmospheric pressure can be assumed to be 101.3 kPa (standard atmospheric pressure at sea level). Therefore, the absolute pressure in the jar is:

P = 101.3 kPa + 27.4 kPa = 128.7 kPa

To know more about gauge pressure, refer to the link below:

https://brainly.com/question/29341536#

#SPJ11

No, the electric current entering and leaving a bulb in a simple battery-and-bulb circuit is the same. The current remains constant throughout a series circuit. The bulb acts as a resistor, which impedes the flow of electrons, causing them to release energy in the form of light.

The rate at which energy is dissipated as light depends on the resistance of the bulb, but the current entering and leaving it is equal. Conservation of charge dictates that the amount of charge flowing into the bulb must be the same as the amount flowing out.

Learn more about circuit here:

https://brainly.com/question/12608516

#SPJ11

The source of electrons at Complex II (Succinate-Q-reductase) is: c. FADH₂ from the citric acid cycle

The citric acid cycle is a metabolic pathway that connects carbohydrate, fat, and protein metabolism. The reactions of the cycle are carried out by eight enzymes that completely oxidize acetate (a two carbon molecule), in the form of acetyl-CoA, into two molecules each of carbon dioxide and water.

During the citric acid cycle, FADH₂ is produced when succinate is converted to fumarate by succinate dehydrogenase. FADH₂ then donates its electrons to Complex II, which are then transferred to the electron transport chain. This process is not directly related to glycolysis or NADH production.

The correct answer is option c.FADH₂ from the citric acid cycle

To learn more about glycolysis https://brainly.com/question/1966268

#SPJ11

The resistances of the two copper wires can be compared using the formula R = ρ(L/A), where R is the resistance, ρ is the resistivity, L is the length, and A is the cross-sectional area. Since both wires have the same length and are made of copper, their lengths and resistivities are the same.

The cross-sectional area of a wire is proportional to the square of its diameter. Therefore, if one wire has twice the diameter of the other, it will have four times the cross-sectional area. This means that the thinner wire has a higher resistance than the thicker wire, because the thinner wire has less space for electrons to flow through.

Using the formula for resistance, we can see that the thinner wire will have four times the resistance of the thicker wire. Therefore, the answer is B: the thinner wire has four times the resistance of the thicker wire.
For the cross-sectional area, A = π(D/2)^2, where D is the diameter. The thicker wire has twice the diameter of the thinner wire, so the cross-sectional area of the thicker wire is (π(2D/2)^2) = 4π(D/2)^2.
Comparing the resistances: R1 = ρ(L/A1) for the thinner wire and R2 = ρ(L/A2) for the thicker wire. Dividing R1 by R2:
R1/R2 = (ρ(L/A1))/(ρ(L/A2)) = A2/A1 = (4π(D/2)^2)/(π(D/2)^2) = 4.
So, the thinner wire has four times the resistance of the thicker wire. The correct answer is B.

To know more about resistances visit:-

https://brainly.com/question/30799966

#SPJ11

1. Object distance > 40 cm from the lens (d). 2. Object distance < 40 cm but > 20 cm from the lens (c). 3. Object distance < 20 cm from the lens (a). 4 and 5. Object distance < 20 cm from the lens (b). 6. Object distance < 20 cm from the lens (a).


1. For the image to be larger than the object, the object distance should be greater than the focal length but less than twice the focal length ( option D).
2. For the image to be smaller than the object, the object distance should be between 20 cm and 40 cm ( option C).
3. For the image to be upright, the object distance should be less than the focal length (20 cm) ( option A).
4. For the image to be inverted, the object distance should be greater than the focal length (20 cm) ( option B).
5. For the image to be real, the object distance should be greater than the focal length (20 cm) ( option B).
6. For the image to be virtual, the object distance should be less than the focal length (20 cm) ( option A).

For more such questions on distance, click on:

https://brainly.com/question/26550516

#SPJ11

The size, orientation, and nature (real or virtual) of the image formed by a converging lens depend on the object distance relative to the focal length of the lens.

Based on observations in the lab with a converging lens of focal length 20 cm, the answers to the questions are: 1. The image will be larger than the object for object distances less than 20 cm from the lens (A). 2. The image will be smaller than the object for object distances greater than 20 cm from the lens (B). 3. The image will be upright for object distances less than 20 cm from the lens (A) and between 40 cm and 20 cm from the lens (C). 4. The image will be inverted for object distances greater than 20 cm from the lens (B) and between 40 cm and 20 cm from the lens (C). 5. The image will be real for object distances between 40 cm and 20 cm from the lens (C) and object distances greater than 40 cm from the lens (D). 6. The image will be virtual for object distances less than 20 cm from the lens (A).

Learn more about converging lens here :

https://brainly.com/question/28348284

#SPJ11

A hydrogen atom can be excited from the n = 2 state to the n = 6 state with a wavelength of around 3.65 x 10⁻¹⁵ m.

To calculate the frequency of light emitted from a hydrogen atom during a transition, we can use the Rydberg formula:

[tex]\frac{1}{\lambda} = R_H \left( \frac{1}{n_f^2} - \frac{1}{n_i^2} \right)[/tex]

where λ is the wavelength, R_H is the Rydberg constant for hydrogen (approximately 3.29 x 10¹⁵ Hz), [tex]n_f[/tex] is the final state, and [tex]n_i[/tex] is the initial state.

For the transition from n = 4 to n = 2, we have:

[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \, \text{Hz} \times \left(\frac{1}{2^2} - \frac{1}{4^2}\right)[/tex]

[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \, \text{Hz} \times \left(\frac{1}{4} - \frac{1}{16}\right)[/tex]

[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \, \text{Hz} \times \frac{3}{16}[/tex]

[tex]\frac{1}{\lambda}[/tex] = 1.21 x 10¹⁵ Hz

So, the frequency of light emitted during this transition is approximately 1.21 x 10¹⁵ Hz.

To calculate the energy difference [tex]Ef - Ei[/tex], we can use the formula:

ΔE = [tex]E_i[/tex] - [tex]E_f[/tex]

where ΔE is the energy difference, [tex]E_i[/tex] is the initial energy, and [tex]E_f[/tex] is the final energy.

The energy of a hydrogen atom in a given state can be calculated using the formula:

[tex]E = \frac{-13.6 \, \text{eV}}{n^2}[/tex]

For the transition from n = 7 to the ground state (n = 1), we have:

[tex]ΔE = \left(-\frac{13.6 \text{ eV}}{1^2}\right) - \left(-\frac{13.6 \text{ eV}}{7^2}\right)[/tex]

      = -13.6 eV + 0.271 eV

      = -13.329 eV

So, the energy difference [tex]Ef - Ei[/tex] is approximately -13.329 eV.

To calculate the wavelength of light that can excite a hydrogen atom from the n = 2 state to the n = 6 state, we can use the Rydberg formula as mentioned earlier:

[tex]\frac{1}{\lambda} = R_H \left( \frac{1}{n_f^2} - \frac{1}{n_i^2} \right)[/tex]

For this transition, we have:

[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \text{ Hz} \left( \frac{1}{6^2} - \frac{1}{2^2} \right)[/tex]

[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \text{ Hz} \left( \frac{1}{36} - \frac{1}{4} \right)[/tex]

[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \text{ Hz} \left( \frac{3}{36} \right)[/tex]

[tex]\frac{1}{\lambda}[/tex]= 2.74 x 10¹⁴ Hz

Now, we can calculate the wavelength:

[tex]\lambda = \frac{1}{2.74 \times 10^{14} \text{ Hz}}[/tex]

   = 3.65 x 10⁻¹⁵ m

So, the wavelength of light that can excite a hydrogen atom from the n = 2 state to the n = 6 state is approximately 3.65 x 10⁻¹⁵ m.

To know more about the wavelength of light refer here :

https://brainly.com/question/20462619#

#SPJ11

A mass is suspended from each end of a rod of unequal lengths. The rod is balanced horizontally by adjusting an unknown mass. Two cases are shown.

When a mass is suspended from each end of a rod of unequal lengths, the rod will not remain horizontal unless an unknown mass is suspended at a specific point on the rod. This point can be determined by balancing the rod horizontally. The position of the unknown mass can be calculated using the principle of moments, which states that the sum of the moments acting on an object must be equal to zero for it to be in equilibrium. In this case, the moments due to the masses on each end of the rod and the unknown mass must be equal and opposite. The position of the unknown mass can then be calculated using the formula m = (l1/l2) * M, where m is the unknown mass, l1 and l2 are the lengths of the rod on either side of the pivot point, and M is the mass on one end of the rod.

learn more about mass here:

https://brainly.com/question/18064917

#SPJ11

To estimate the percent increase in capacitance between using a distance d and reducing it to d + Δd, we can utilize the formula for capacitance of parallel plate capacitors:

C = εA/d

Where C is the capacitance, ε is the permittivity of the material between the plates, A is the area of the plates, and d is the distance between the plates.

To calculate the percent increase, we compare the capacitance for the initial distance (d) and the final distance (d + Δd).

Let's denote the initial capacitance as C1 and the final capacitance as C2. The percent increase in capacitance can be estimated using the following formula:

Percent Increase = ((C2 - C1) / C1) * 100

Now, if we reduce the distance from d to d + Δd, the new capacitance C2 can be calculated as:

C2 = εA / (d + Δd)

Substituting these values into the percent increase formula, we have:

Percent Increase = (((εA / (d + Δd)) - (εA / d)) / (εA / d)) * 100

Simplifying further, the formula becomes:

Percent Increase = (Δd / d) * 100

So, the percent increase in capacitance between using a distance d and reducing it to d + Δd is equal to (Δd / d) * 100.

Note that this is an estimation and assumes that the area of the plates and the permittivity of the material remain constant during the change in distance.

Learn more about **capacitance** and its relationship with distance in parallel plate capacitors here:

https://brainly.com/question/12119641?referrer=searchResults

#SPJ11

We can use the formula for the period of oscillation of a simple harmonic oscillator to find the frequency of vibration of the atoms in the KF crystal the spacing of adjacent atoms in a KF crystal is 0.266.

An oscillator is a physical system that undergoes periodic motion about an equilibrium position. The frequency of an oscillator is the number of cycles or oscillations it completes in one second and is typically measured in units of Hertz (Hz). The frequency of an oscillator depends on its physical properties, such as its mass and stiffness, and can be affected by external factors such as friction and driving forces. In the context of physics, oscillators are used to model a wide variety of physical phenomena, from simple mechanical systems like springs and pendulums to complex systems like atoms and molecules.

To know more about molecules visit :

https://brainly.com/question/19922822

#SPJ11

The approximate surface temperature of the star is 4143 K (3870.85 °C).

The peak wavelength of a star's spectrum gives an indication of its temperature through Wien's law, which states that the wavelength at which maximum radiation is emitted is inversely proportional to the temperature.

The formula for Wien's law is λmax = b/T, where λmax is the wavelength of maximum intensity, T is the temperature in Kelvin, and b is Wien's displacement constant, which is equal to 2.898 × [tex]10^{-3}[/tex] m⋅K.

To determine the surface temperature of the star, we need to convert the peak wavelength from the border between red and infrared light to meters. This is approximately 700 nm or 7 × [tex]10^{-7}[/tex] m. We can then use Wien's law to solve for the temperature:

λmax = b/T

T = b/λmax

T = 2.898 × [tex]10^{-3}[/tex] m⋅K / 7 × [tex]10^{-7}[/tex] m

T ≈ 4143 K

To convert Kelvin to Celsius, we subtract 273.15: T ≈ 4143 K - 273.15, T ≈ 3870.85 °C

Therefore, the approximate surface temperature of the star is 4143 K (3870.85 °C).

To know more about Wien's law, refer here:

https://brainly.com/question/28480860#

#SPJ11

The speed of the alpha particle when it is emitted is 1.4 x 10⁶ m/s.

According to conservation of momentum, the momentum of the system before the alpha particle is emitted must be equal to the momentum of the system after the alpha particle is emitted.

We can use the formula p = mv, where p is momentum, m is mass, and v is velocity. Initially, the momentum of the system is (222 u)(320 m/s), since the original nucleus is moving at 320 m/s.

After the alpha particle is emitted, the momentum of the system is (4.0 u)(v) + (218 u)(280 m/s), where v is the velocity of the alpha particle.

Setting these two expressions equal, we get (222 u)(320 m/s) = (4.0 u)(v) + (218 u)(280 m/s), and solving for v, we get v = (222 u)(320 m/s) - (218 u)(280 m/s) / (4.0 u) = 1.4 x 10⁶ m/s. The answer is expressed to one significant figure because the given values have one significant figure.

To know more about alpha particle, refer here:

https://brainly.com/question/24276675#

#SPJ11

a) The speed of the clay immediately before impact was 0.033 m/s. b) No, static friction could not prevent the block from moving after being struck by the wad of clay if the collision took place in a time interval of 0.100 s.

The initial momentum of the clay and the block is given by:

p = mv = (m₁ + m₂)v₁

After impact, the clay sticks to the block, so the final momentum is:

p' = (m₁ + m₂)v₂

By the law of conservation of momentum, we have:

p = p'

(m₁ + m₂)v₁ = (m₁ + m₂)v₂

v₁ = v₂

The final velocity of the block is given by:

v₂ = √(2umgd/(m₁ + m₂))

where u is the coefficient of friction, m is the mass of the block, g is the acceleration due to gravity, and d is the distance traveled by the block.

Substituting the given values, we get:

v₂ = √(20.6500.1109.817.50/(0.110 + 0.011))

v₂ = 3.01 m/s

Now, the initial momentum of the clay can be found by:

p = mv = (11.0 g)(v₁)

Converting the mass to kg and solving for vi, we get:

v₁ = p/(m₁)

= (0.011 kg)(v₂)

= 0.033 m/s

The force of the wad of clay on the block is greater than the maximum static frictional force that the surface can provide, so the block will continue to slide.

To know more about friction, here

https://brainly.com/question/28356847

#SPJ4

Therefore, the total transmitted intensity is 0.375I + 0.159I = 0.534I.

To find the transmitted intensity, we need to use Malus' Law which states that the intensity of light transmitted through a polarizer is proportional to the square of the cosine of the angle between the transmission axis of the polarizer and the polarization direction of the incident light.

For the first polaroid sheet, the transmitted intensity will be I/2 since it is unpolarized light and half of it will be blocked by the sheet.
For the second polaroid sheet, the transmission axis is perpendicular to the first sheet, so the angle between the transmission axis and the polarization direction of the incident light is 90 degrees. Therefore, the transmitted intensity will be 0.
For the third polaroid sheet, the transmission axis makes an angle of 30 degrees with the first sheet. The cosine of 30 degrees is 0.866, so the transmitted intensity will be (I/2) * (0.866)^2 = 0.375I.
For the fourth polaroid sheet, the transmission axis is perpendicular to the third sheet, so the transmitted intensity will be 0.
Finally, for the fifth polaroid sheet, the transmission axis makes an angle of 30 degrees with the third sheet. The cosine of 30 degrees is 0.866, so the transmitted intensity will be (0.375I) * (0.866)^2 = 0.159I.
Therefore, the total transmitted intensity is 0.375I + 0.159I = 0.534I.

To know more about intensity visit:-

https://brainly.com/question/15283903

#SPJ11

If an electron is moving in a horizontal straight line, it means that there is no force acting on it in the horizontal direction. However,

if there is a magnetic field present, it will exert a force on the moving electron in a direction perpendicular to both the velocity of the electron and the magnetic field.

The magnitude of this force is given by the equation F = Bqv, where F is the force, B is the magnitude of the magnetic field, q is the charge of the electron, and v is the velocity of the electron.

Since we know that the electron is moving in a straight line, we can assume that the force acting on it is balanced by some other force, such as the electrostatic force.

Therefore, we can set the magnitude of the magnetic force equal to the magnitude of the electrostatic force and solve for B.

Assuming the electron has a charge of e, and the electrostatic force is given by F = eqE, where E is the electric field, we can set the two forces equal to each other and get:

Bqv = eqE

Simplifying this equation, we get:

B = E(v/e)

Therefore, the magnitude of the magnetic field in terms of v and e is given by B = E(v/e). This equation shows that the magnitude of the magnetic field is proportional to

the electric field and the velocity of the electron, and inversely proportional to the charge of the electron.

To know more about electron refer here

https://brainly.com/question/12001116#

#SPJ11

The mass of hydrogen required by the fuel cell to run the gadget for 30 min is 2.78 grams.10 stacked cells are needed to generate 6.00 kW of power at the average voltage of the fuel cell of 0.60 V and current of 100 A.

Problem 1:

The mass of hydrogen required by a fuel cell can be calculated using the following formula:

mass = (I * t * n * M) / (2 * F)

Given:

I = 250 A (current)

t = 30 min = 1800 s (time)

n = 2 (number of electrons transferred per mole of hydrogen)

M = 2.01 g/mol (molar mass of hydrogen)

F = 96500 C/mol (Faraday constant)

Substituting these values into the formula, we get:

mass = (250 A * 1800 s * 2 * 2.01 g/mol) / (2 * 96500 C/mol)

mass = 2.78 g

Therefore, the mass of hydrogen required by the fuel cell to run the gadget for 30 min is 2.78 grams.

Problem 2:

The power generated by a fuel cell can be calculated using the following formula:

P = V * I

where P is the power (in watts), V is the voltage (in volts), and I is the current (in amperes).

Given:

P = 6.00 kW (power)

V = 0.60 V (voltage)

I = 100 A (current)

Substituting these values into the formula, we get:

P = V * I

6000 W = 0.60 V * 100 A

Solving for V, we get:

V = P / I

V = 6000 W / 100 A

V = 60 V

Therefore, the average voltage of the fuel cell is 60 V.

The number of stacked cells needed can be calculated using the following formula:

n = P / (V * I)

where n is the number of stacked cells, P is the power (in watts), V is the average voltage of the fuel cell (in volts), and I is the current (in amperes).

Substituting the given values, we get:

n = 6.00 kW / (60 V * 100 A)

n = 10

Therefore, 10 stacked cells are needed to generate 6.00 kW of power at the average voltage of the fuel cell of 0.60 V and current of 100 A.

Learn more about voltage here:

https://brainly.com/question/29445057

#SPJ11

It is a measure of the opposition that a capacitor provides to the flow of an alternating current. The value of capacitive reactance is inversely proportional to the frequency of the alternating current.

The ratio of the capacitive reactance of a typical clavus sample to that of verruca will depend on the frequency at which it is measured. At low frequencies, the capacitive reactance of both clavus and verruca will be similar

However, as the frequency increases, the capacitive reactance of the clavus sample will decrease at a faster rate compared to verruca. This is because the clavus sample is denser than verruca and has a higher dielectric constant.

To know more about alternating current visit:-

https://brainly.com/question/11673552
#SPJ11

The speed of sound is approximately 350.87 m/s on a day when a 1523 Hz frequency has a wavelength of 0.229 m.


The formula to calculate the speed of sound is v = fλ, where v is the speed of sound, f is the frequency, and λ is the wavelength.
Substituting the given values, we get:
v = 1523 Hz x 0.229 m = 348.47 m/s
However, the speed of sound varies with temperature, humidity, and air pressure. At standard temperature and pressure (STP), which is 0 °C and 1 atm, the speed of sound is 331.3 m/s. Assuming STP conditions, we can use the following formula to find the speed of sound:
v = 331.3 m/s x √(1 + (T/273.15))
where T is the temperature in Celsius. If we assume a temperature of 20 °C, we get:
v = 331.3 m/s x √(1 + (20/273.15)) = 350.87 m/s
Therefore, the speed of sound is approximately 350.87 m/s on a day when a 1523 Hz frequency has a wavelength of 0.229 m, assuming standard temperature and pressure conditions.

Learn more about sound here:

https://brainly.com/question/29707602

#SPJ11

To calculate the lift on a wing, we can use the following formula:

Lift = 1/2 x Density x Velocity^2 x Wing Area x Coefficient of Lift

Where:

- Density is the density of the air at the given altitude and temperature

- Velocity is the true airspeed in feet per second (fps)

First, we need to convert the given airspeed of 200 ktas (knots true airspeed) to fps:

200 ktas = 368.8 fps (at standard day conditions)

Next, we need to find the density of the air at an altitude of 5,000 ft on a standard day. According to the International Standard Atmosphere (ISA) model, the density at this altitude is approximately 0.0023769 slugs/ft^3.

Now we can plug in the values and solve for Lift:

Lift = 1/2 x 0.0023769 slugs/ft^3 x (368.8 fps)^2 x 150 ft^2 x 0.8

Lift = 14,632 pounds (rounded to the nearest pound)

Therefore, the lift on the wing is approximately 14,632 pounds.

To know more about density refer here

https://brainly.com/question/29775886#

#SPJ11

The ideal efficiency of the heat engine is 88.1%.

The ideal efficiency of a heat engine operating between two temperatures can be determined by using the Carnot cycle. The efficiency is given by the formula (Th - Tc)/Th, where Th is the temperature of the hot reservoir and Tc is the temperature of the cold reservoir.

In this case, Th = 227°C and Tc = 27°C. Therefore, the ideal efficiency of the heat engine can be calculated as (227 - 27)/227 = 0.881 or 88.1%. This means that the heat engine can convert 88.1% of the heat energy it receives into useful work. It is important to note that this is an ideal efficiency and real-world heat engines may have lower efficiencies due to factors such as friction, heat loss, and other inefficiencies in the system.

To know more about heat engine operating visit:

https://brainly.com/question/13144439

#SPJ11

The mass of a black hole is calculated based on its gravitational effects on surrounding objects.

By observing the orbits of stars and gas clouds around the black hole, scientists can determine its mass through the use of Kepler's laws of motion and Newton's law of gravitation.  By applying the principles of general relativity and Newton's law of universal gravitation, the mass of the black hole can be determined.

Additionally, the mass of a black hole can be estimated from the amount of radiation emitted by the matter falling into the black hole, known as accretion. Overall, calculating the mass of a black hole requires a combination of observational data and theoretical models.

Learn more about black hole here:

https://brainly.com/question/15702481

#SPJ11

The electron's speed when it reaches 721 volts is approximately 2.75 x [tex]10^6[/tex] m/s, considering the change in potential energy.


To find the speed of the electron when it reaches 721 volts, we must first consider the change in potential energy.

The initial potential energy is qV1, where q is the charge of an electron (1.6 x [tex]10^{-19[/tex] C) and V1 is the initial voltage (1211 V).

The final potential energy is qV2, with V2 being the final voltage (721 V). The change in potential energy (∆PE) is q(V1 - V2).
Next, we can use the conservation of energy principle: ∆PE = [tex]1/2mv^2[/tex], where m is the electron mass (9.11 x [tex]10^{-31[/tex] kg) and v is the velocity.

Solving for v, we find that the electron's speed is approximately 2.75 x [tex]10^6[/tex] m/s when it reaches 721 volts.

For more such questions on energy, click on:

https://brainly.com/question/13881533

#SPJ11

(a) The rate of heat conduction through the fur is 16,800 W.

(b)The animal needs to consume approximately 8.72 x 10^9 calories of food

(a)The rate of heat conduction through the fur can be found using the formula:

Q/Δt = kA(ΔT/d)

where Q/Δt is the rate of heat conduction, k is the thermal conductivity of the fur (assumed to be the same as air), A is the surface area, ΔT is the temperature difference between the skin and air, and d is the thickness of the fur.

Substituting the given values:

Q/Δt = (0.024 W/m·K)(1.40 m^2)(32.0°C - (-5.00°C))/(0.03 m)

Q/Δt = 16,800 W

(b)To replace the heat transfer through the fur in one day, the animal must consume an amount of food that provides the same amount of energy. The energy needed can be found using the formula:

Energy = power x time

where power is the rate of heat conduction found in part (a) and time is the number of seconds in one day:

Energy = (16,800 W)(24 hours)(60 min/hour)(60 s/min)

Energy = 3.65 x 10^10 J

Converting to food energy, 1 calorie (cal) = 4.184 J, so:

Food energy = (3.65 x 10^10 J)/(4.184 J/cal)

Food energy = 8.72 x 10^9 cal

To know more about rate of heat conduction refer here

https://brainly.com/question/20815787#

#SPJ11

a. The smallest value of 'a' for which there are two stable nuclei is 3.

In this case, the stable nuclei are tritium (Hydrogen-3) and Helium-3. Both of these isotopes have an atomic mass number (A) of 3, and they are considered stable under certain conditions.

b. For values of 'a' less than 3, there are no stable nuclei.

The nuclei with atomic mass numbers (A) of 1 and 2 are not considered stable, as they undergo decay or have a short half-life. For example, Hydrogen-1 (also known as a single proton) does not have any neutrons, and Deuterium (Hydrogen-2) is stable but often considered a special case due to its simplicity.

To know more about stable and unstable nuclei

brainly.com/question/31979217

#SPJ11

True. The molar enthalpy of fusion of solid ammonia is 5.65 kJ/mol, and the molar entropy of fusion is 28.9 J/K mol.

The molar enthalpy of fusion refers to the amount of energy required to change one mole of a substance from its solid phase to its liquid phase at a constant temperature and pressure. In the case of ammonia, this value is given as 5.65 kJ/mol. This means that it takes 5.65 kJ of energy to melt one mole of solid ammonia.

On the other hand, the molar entropy of fusion refers to the change in entropy (a measure of the randomness or disorder of a system) when one mole of a substance undergoes a phase transition from solid to liquid at a constant temperature and pressure. For ammonia, the molar entropy of fusion is 28.9 J/K mol, which means that the entropy of the system increases by 28.9 J/K for every mole of solid ammonia that melts.

To know more about entropy, click here;

https://brainly.com/question/13135498

#SPJ11

The particle's velocity at s = 7 m is approximately 3.16 m/s.

To find the particle's velocity at s = 7 m, we need to first integrate the acceleration function a(s) = 1/2s^(1/2) m/s² with respect to s. This will give us the velocity function v(s).

∫(1/2s^(1/2)) ds = (1/3)s^(3/2) + C

Now, we need to determine the integration constant C. We are given that v = 0 when s = 4 m. Let's use this information:

0 = (1/3)(4^(3/2)) + C
C = -8/3

The velocity function is then v(s) = (1/3)s^(3/2) - 8/3.

Now, we can find the velocity at s = 7 m:

v(7) = (1/3)(7^(3/2)) - 8/3 ≈ 3.16 m/s

So, the particle's velocity at s = 7 m is approximately 3.16 m/s.

Learn more about velocity here: https://brainly.com/question/25905661

#SPJ11

An example of a transverse wave is a light wave, while an example of a longitudinal wave is a sound wave.

In a transverse wave, like a light wave, the disturbance (vibrations) occurs perpendicular to the direction of wave propagation. For instance, when light travels through space, its electric and magnetic fields oscillate at right angles to the direction in which the wave is moving.

On the other hand, in a longitudinal wave, such as a sound wave, the disturbance (vibrations) occurs parallel to the direction of wave propagation. In the case of sound waves, the air particles move back and forth, compressing and rarefying in the same direction as the wave is traveling.

To summarize, a transverse wave example is a light wave with perpendicular disturbance, and a longitudinal wave example is a sound wave with parallel disturbance to the direction of wave propagation.

To know more about Transverse wave refer here :

https://brainly.com/question/14693510

#SPJ11

a) 50 ml of NaOH solution b) 100 ml of NaOH solution c) 150 ml of NaOH solution d) 200 ml of NaOH solution a) Before the equivalence point b) At the equivalence point c) After the equivalence point d) After the equivalence point

In this titration, the HCl solution is the analyte and NaOH solution is the titrant. At the equivalence point, the moles of HCl and NaOH react in a 1:1 ratio, meaning all the HCl has reacted with the NaOH added. Before the equivalence point, there is excess HCl, and after the equivalence point, there is excess NaOH. a) 50 ml of NaOH solution: At this point, not all of the HCl has reacted with the NaOH, and there is still HCl left in the solution. Therefore, this is before the equivalence point.

b) 100 ml of NaOH solution: This is the point where the moles of HCl and NaOH react in a 1:1 ratio, which is the equivalence point.

c) 150 ml of NaOH solution: At this point, all the HCl has reacted with the NaOH, and there is excess NaOH in the solution. Therefore, this is after the equivalence point.

d) 200 ml of NaOH solution: This is also after the equivalence point since all the HCl has already reacted with the NaOH, and there is excess NaOH in the solution.

learn more about solution here:

https://brainly.com/question/30620786

#SPJ11

A. Coulomb's law and Newton's law of gravitation are similar in that they both describe the forces between objects. However, they differ in the type of force they describe. Coulomb's law relates to the electrostatic force between charged particles, while Newton's law of gravitation describes the gravitational force between two objects with mass.

B. A coulomb of charge is equal to the charge possessed by approximately 6.24 x 10^18 electrons. This means that a single electron carries a charge of 1.6 x 10^-19 coulombs. C. The magnitude of the electrical force between charged particles decreases when the particles are moved farther apart. If the particles are moved twice as far apart, the magnitude of the force decreases by a factor of 4 (1/2^2). If the particles are moved three times as far apart, the magnitude of the force decreases by a factor of 9 (1/3^2). D. An electrically polarized object differs from an electrically charged object in that polarization refers to the redistribution of charges within a neutral object under the influence of an external electric field. In an electrically polarized object, the charges shift, resulting in a separation of positive and negative charges. However, the object as a whole remains neutral. In contrast, an electrically charged object has a net surplus or deficit of electrons, leading to an overall positive or negative charge.

learn more about Newton's here:

https://brainly.com/question/28443975

#SPJ11

The word intermolecular is made up of two parts - "inter" meaning between and "molecular" meaning relating to molecules. Intermolecular forces of attraction refer to the forces that exist between molecules.

These forces are responsible for the physical properties of substances such as their boiling and melting points. There are different types of intermolecular forces such as van der Waals forces, dipole-dipole forces, and hydrogen bonding. Van der Waals forces are the weakest and result from the temporary dipoles that occur in molecules. Dipole-dipole forces are stronger and result from the attraction between polar molecules. Hydrogen bonding is the strongest type of intermolecular force and occurs when hydrogen is bonded to a highly electronegative atom such as nitrogen, oxygen, or fluorine. This results in a strong dipole-dipole interaction between molecules.

Analyze the parts of the word "intermolecular" and define intermolecular forces of attraction.

The word "intermolecular" can be broken down into two parts:

1. "Inter" - This prefix means "between" or "among."
2. "Molecular" - This term refers to molecules, which are the smallest units of a substance that still retain its chemical properties.

When combined, "intermolecular" describes something that occurs between or among molecules.

Now let's define intermolecular forces of attraction:

Intermolecular forces of attraction are the forces that hold molecules together in a substance. These forces result from the attraction between opposite charges in the molecules, and they play a crucial role in determining the physical properties of substances, such as their boiling points, melting points, and density. Some common types of intermolecular forces include hydrogen bonding, dipole-dipole interactions, and London dispersion forces.

To know more about forces visit:

https://brainly.com/question/24215119

#SPJ11

Answer:

Use conservation of momentum

I ω = I1 ω1 + I2 ω2 =  I1 ω1         initially =   I1 ω1 since  ω2 = zero

I ω = a constant

(I1 + I2)  ω     is the final angular momentum

or (I1 + I2)  ω = I1 ω1