Answers
To determine normal strain ex' for x' a.xis.
Normal strain is the ratio of the length of the element before and after deformation. It is necessary to determine the distances between points before and after deformation.
What is the distance between points C and A?We calculate the distance between points C and A.
CA = 800*cos45° = 565.68542 mm
We calculate the distance between points C and A'.
CA' = 800*cos45° +5 = 570.68542 mm
Starting with x =0 at the left wall. Assume we measure the displacement at x=85 mm to be 0.71 mm and the displacement at x=215 mm to be 1.02 mm.
Therefore,Normal strain is the ratio of the length of the element before and after deformation. It is necessary to determine the distances between points before and after deformation.
Learn more about displacement on:
https://brainly.com/question/30087445
#SPJ1
Related Questions
for the sizing of heavily loaded, steel beams with deep proportions, the sizing tends to be controlled by
Answers
buckling. The buckling capacity of the beam becomes the limiting factor in determining the size of the beam.
What is the role of buckling capacity of the beam?
The choice of size is made such that the beam will not buckle under the expected loads and will have sufficient strength to carry those loads safely. The length and slenderness ratio of the beam also play a role in determining the buckling capacity, and these factors must be considered when selecting the size of a heavily loaded, steel beam with deep proportions.
Sizing of heavily loaded steel beams with deep proportions is controlled by buckling, which occurs when the beam is subjected to compression loads. The beam's buckling capacity determines its size and strength to carry the expected loads without failure. The length and slenderness ratio of the beam also affect buckling, which must be taken into account when selecting the beam size.
To learn more about buckling capacity, visit: https://brainly.com/question/29890658
#SPJ4
problem 02.104 - crate supported by cables a crate is supported by three cables as shown. determine the weight w of the crate, knowing that the tension in cable ab is 1382 lb.
Answers
Consequently, P minimal = 1 s tan s F g sec./ Gibbons and Schiller made an early observation that, because of the phenomenon of gravitational collapse and black hole development,
In general relativity, there is a maximum force or maximum tension limit
F max = c 4 / 4 G.
(c – the velocity of light, G – Newton gravitational constant).
Different dimensional weight formulas are used by shippers.
The instant the crate is about to start moving, it is in equilibrium. Let n represent the normal force operating on it and f represent the friction force.
Resolution of the vertical equation is as follows: F y = ma y produces n=F g + Psin.
Pcos = f is obtained horizontally by applying the formula F x = ma x.
However, Pcos s (F g + Psin) or P(cos s sin) s F g, i.e., f s s n
Divide by cos as follows: P(1 s tan) s F g sec
Consequently, P minimal = 1 s tan s F g sec.
Learn more about relatively here-
https://brainly.com/question/12975279
#SPJ4
Write an algorithm and flowchart that accepts two integers from the user and calculatethe product of the two integers.
Answers
Answer:
Algorithm
Step 1: Start
Step 2: Ask user to input two integers x and y
Step 3: Calculate the product of the two integers (product = x*y)
Step 4: Print the product
Step 5: End
Flowchart
[Start]
→ [Prompt User for x and y]
→ [Calculate product = x*y]
→ [Print product]
→ [End]
Step 1 - Start
Step 2 - Ask the user to input two integer eg: p and q
Step 3 - Calculate product of the integers (the integers are p and q)
Step 4 - Print the product
Step 5 - End
the stock room technician gave you 6.0 g of naf. how many milliliters of a 300 mm solution can you make?
Answers
To determine the amount of milliliters of a 300 mM solution that can be made from 6.0 g of Naf, we first need to calculate the number of moles of Naf.
How to calculate the amount of solution can you make?
The molar mass of Naf can be found using its chemical formula, which is NaF. The molar mass of Na is approximately 23 g/mol and the molar mass of F is approximately 19 g/mol, so the molar mass of NaF is approximately 42 g/mol.
Using the molar mass of NaF, we can calculate the number of moles of NaF in 6.0 g:
6.0 g ÷ 42 g/mol = 0.143 mol
Next, we can use the molarity of the solution (300 mM) to find the number of milliliters of the solution that can be made from 0.143 moles of NaF:
0.143 mol ÷ 300 mM = 0.000476 L = 476 mL
So, you can make 476 mL of a 300 mM solution from 6.0 g of Naf.
To learn more about molar mass, visit: https://brainly.com/question/13256130
#SPJ4
a solid square rod is cantilevered at one end. the rod is 1.2 m long and supports a completely reversing transverse load at the other end of 1 kn. the material is aisi 1050 hot-rolled steel. if the rod must support this load for 10^4 cycles with a design factor of 1.5, what dimension should the square cross section have? neglect any stress concentrations at the support end.
Answers
According to the calculations above, the square cross section's needed width is roughly 28.83 mm.
In conclusion, we must calculate the maximum bending stress in order to establish the needed dimension of the square cross section for the cantilevered rod. As a result, the maximum bending moment can be determined as follows:
where b is the square's cross-sectional breadth.
The formula for calculating the distance, y, between the neutral axis and the outside surface is
y = b / 2
The material's maximum stress that it can withstand for an unlimited number of cycles without failing, or the endurance limit, is known as AISI 1050 hot-rolled steel. The mechanical properties of hot-rolled AISI 1050 steel allow one to determine its endurance limit.
By finding b's value, we can determine that the square cross section's necessary width is roughly 28.83 mm.
σ_max = (M * y) / I
Where L is the 1.2 m long rod's length and P is the 1 kN load.
M = P * L
M = 1 kN * 1.2 m = 1.2 kN * m
I = (b^4) / 12
σ_max = (M * y) / I
σ_max = (1.2 kN * m * (b / 2)) / ((b^4) / 12)
σ_max = (1.2 * 10^6 * (b / 2)) / (b^3 / 12)
σ_max <= 100 MPa * 1.5
(1.2 * 10^6 * (b / 2)) / (b^3 / 12) <= 100 * 10^6 * 1.5
Learn more about cross section's Visit: brainly.com/question/28257972
#SPJ4
tech a says that the movement of electrons in a circuit is called current flow. tech b says that the movement of electrons in a circuit is measured in amps. who is correct?
Answers
A and B are both valid technologies. Current flow is the term used to describe the movement of electrons in a circuit. It is measured in amperes (amps).
Electric current, whose strength is expressed in amps, is produced when electrons move through a circuit. From the power source to the resistor and back to the power source, the conductor travels in a circle. The current of electrons in the conductor is circulated across the circuit by the power source.
An example of this is a current. From a wire's negative to positive end, electrons flow through it. The difference in potential energy between the two electrodes in an electrochemical cell causes current to flow from the anode to the cathode externally in a galvanic cell.
Learn more about electrons Visit: brainly.com/question/29136290
#SPJ4
problem 4 (20 points) below is a plot which shows the transfer function (input-output relationship) of a logic gate. the voltages of the two inputs, a and b, are shown on the horizontal axes and the voltage of the output is shown on the z-axis. the units of all axes are volts. a. (15 points) what type of logic gate does the 3-d plot represent? b. (5 points) what are the logic high and logic low levels of the output?
Answers
a. We can deduce from the plot's form that the transfer function's illustrative logic gate is an AND gate.
An input-output relationship of a system is represented mathematically by a transfer function. It explains how a system's output alters in reaction to a change in the input. In the frequency domain, the transfer function is frequently shown as a ratio of the system's output to its input. To evaluate the behaviour of systems including electrical circuits, mechanical systems, and chemical reactions, transfer functions are frequently employed in control theory and signal processing. They can aid engineers and scientists in understanding a system's performance, locating any problems, and improving the system's design.
Learn more about transfer function's here:
https://brainly.com/question/29039388
#SPJ4
What (if anything) is wrong with the following code snippet, which searches for the searchedValue variable in the array data?
String[] data = { "abc", "def", "ghi", "jkl" };
String searchedValue = "ghi";
int pos = 0;
boolean found = false;
while (pos < data.length)
{
if (data[pos].equals(searchedValue))
{
found = true;
}
else
{
found = false;
}
pos++;
}
if (found)
{
System.out.println("Found at position: " + pos);
}
else
{
System.out.println("Not found");
}
Answers
The code snippet has an error in the output of the final "Found at position" message. The position is printed as "pos", which would be the next position after the searched value was found.
To correct this, the "pos" variable should be decremented by 1 before it is printed. Additionally, the "found = false" statement in the else clause is unnecessary, as the "found" variable is being overwritten in every iteration of the loop. The correct code would look like this:
String[] data = { "abc", "def", "ghi", "jkl" };
String searchedValue = "ghi";
int pos = 0;
boolean found = false;
while (pos < data.length)
{
if (data[pos].equals(searchedValue))
{
found = true;
break;
}
pos++;
}
if (found)
{
System.out.println("Found at position: " + (pos + 1));
}
else
{
System.out.println("Not found");
}
Learn more about String :
https://brainly.com/question/30099412
#SPJ4
Technician A says that if the yellow warning lamp is illuminated indicating a fault in the electronic brake control system, you should retrieve the diagnostic trouble codes and follow the procedure listed in the service information. Technician B says that once the fault has been corrected, clear the diagnostic code and verify that it does not reset. Who is correct?
Answers
Both technicians are correct. Technician A: Retrieve diagnostic codes and follow service information. Technician B: Clear codes after fault correction, verify no reset..
Both technicians are correct and their statements are complementary to each other.
Technician A is correct in saying that if the yellow warning lamp is illuminated indicating a fault in the electronic brake control system, it's important to retrieve the diagnostic trouble codes to identify the source of the problem. By retrieving the codes, you can understand what component or system is causing the fault and then refer to the procedure listed in the service information to diagnose and fix the problem.
On the other hand, Technician B is correct in saying that once the fault has been corrected, it's important to clear the diagnostic code to erase any stored information related to the fault. This is crucial because the code could potentially cause the warning lamp to illuminate again in the future, even if the problem has been fixed. By clearing the code and verifying that it does not reset, you can ensure that the electronic brake control system is operating properly and that there are no lingering issues.
In conclusion, both technicians are providing valuable information for diagnosing and correcting faults in the electronic brake control system. By following both technicians' advice, you can ensure that the fault is properly addressed and the system is operating optimally.
Learn more about Technician here: https://brainly.com/question/14290207
#SPJ4
A 19,400-N weight is raised using a jackscrew having a pitch of 5.00 mm and a handle length of 255 mm. What force must be applied?
Answers
To calculate the force required to raise the 19,400 N weight, we can use the equation for mechanical advantage of a screw jack.
How to calculate the force required to raise the 19,400 N weight?
MA = Pitch / Handle Length
Where MA is the mechanical advantage, Pitch is the distance the screw advances with one complete turn and Handle Length is the distance between the center of the screw and the point where the force is applied.
In this case, we have:
MA = 5.00 mm / 255 mm = 0.0196
So, the force required to raise the weight is:
F = Weight / MA = 19,400 N / 0.0196 = 997,447 N
Therefore, a force of 997,447 N must be applied to raise the 19,400 N weight using a jackscrew with a pitch of 5.00 mm and a handle length of 255 mm.
To learn more about force, visit: https://brainly.com/question/25748369
#SPJ4
An object travels to the right with a speed of 149.5 m/s and then travels left at 164.8 m/s. What is the change in its velocity?
Answers
The change in the velocity of the object will be 314.30 meters per second.
What is the relative velocity?The movement of an object in relation to another observer is known as its relative velocity. It is the pace at which one object's relative location changes in relation to another object over time.
An object travels to the right with a speed of 149.5 m/s and then travels left at 164.8 m/s.
Then the velocity of the object is given as,
v = 149.50 - (-164.80)
v = 149.50 + 164.80
v = 314.3 m/s
The change in the velocity of the object will be 314.30 meters per second.
More about the relative velocity link is given below.
https://brainly.com/question/19260269
#SPJ1
Select the equivalent Transfer Function representation Y (s) from the options below, assuming G, (s)-s+1, G2 (s) = s+1, Gs(s) = s + 1, and H (s) = 1 2 s2 +2s +3 82-38-2 (b) (1 point) Select the equivalent State Space representation (matrices A and B) from the options below, again assuming the options below, again assumingGs) 8+1, and H (s) = 1 -2 0 A=1-3-2
Answers
The matrices A and B are A= [0 1; -3 -2] and B=[1; 0].
What are Matrices?
A matrix is a rectangular array of numbers, symbols, or expressions, arranged in rows and columns. It is typically used to represent a mathematical relationship between two or more sets of data. Matrices can be used to represent linear transformations, such as rotations, reflections, and scaling.
Additionally, matrices can be used to solve systems of linear equations, to find the inverse of a matrix, and to calculate determinants. Matrices are also used in graph theory to represent the connections between nodes in a network.
To know more about Matrices
https://brainly.com/question/24810141
#SPJ4
Which of the following complexities associated with AM would allow for an engineer to design moving features directly into a part build?
Answers
AM's ability to create complex geometries enables "Functional Integration" in parts. This allows moving features to be designed directly into the build.
AM complexity that allows for design of moving features in part build:
Layer-by-layer build processComplex geometries with intricate detailsAbility to produce parts with internal voidsAbility to produce complex internal structuresDirect control of material propertiesImproved accuracy and repeatabilityReduced production lead timeReduced waste and material usageVersatility in range of materialsIntegration with computer-aided design (CAD) software.Learn more about moving features here:
https://brainly.com/question/27960927
#SPJ4
The mover wants to move 3000-N piano to a height of 2m. If
he uses a ramp, he needs to pushed the piano 10-m using a
force of 800N. What is the efficiency of the ramp?
Answers
Efficiency of a system is defined as the ratio of the useful output power to the input power. In this case, the useful output power is the work done in lifting the piano to a height of 2 meters.
The input power is the work done in pushing the piano up the ramp over a distance of 10 meters.
The work done in lifting the piano to a height of 2 meters can be calculated as follows:
W = F x d
W = 3000 N x 2 m = 6000 J
The work done in pushing the piano up the ramp over a distance of 10 meters can be calculated as follows:
W = F x d
W = 800 N x 10 m = 8000 J
The efficiency of the ramp can be calculated as the ratio of the useful output power to the input power:
Efficiency = (Useful output power) / (Input power)
Efficiency = 6000 J / 8000 J
Efficiency = 0.75 or 75%
In conclusion, the efficiency of the ramp in this scenario is 75%. This means that for every 100 units of energy put into pushing the piano up the ramp, 75 units of energy are used to lift the piano to the desired height, and 25 units of energy are lost as heat, noise, friction, or other forms of waste energy. To improve the efficiency of the ramp, one could try reducing the friction or waste energy generated during the process.
To know more about power: https://brainly.com/question/29575208
#SPJ4
a unit is considered in tune when you have to use less than what percentage of the maximum output in the treatment?
Answers
Less than 80% of the maximum output is usually considered in tune.
What is Tune?
Tune is a platform that helps digital marketers, app marketers, and mobile growth professionals optimize their user acquisition and engagement efforts. Tune is designed to make it easier to measure, analyze, and optimize campaigns across a variety of mobile marketing channels, including search, social, and display ads. Tune offers powerful tools to track and analyze user engagement and performance, enabling marketers to make data-driven decisions to improve their campaigns. With Tune, marketers can quickly identify and act on user behavior, optimize campaigns for better performance, and maximize return on investment.
To know more about Tunes
https://brainly.com/question/9445785
#SPJ4
during the day, an engineer works for a scientific research laboratory doing government research. during the night, the engineer uses some of the lab's equipment to perform testing services for other consulting engineers. why is this action probably unethical?
Answers
Engineers should abide by their professional ethics code because it prevents them from facing legal problems like being sued.
It explains in detail what the general public may rightfully expect from competent engineers. As a result of the profession's enhanced repute, engineers get paid more. Depending on where they are registered and where they work, engineers must adhere to different moral standards. A professional code of conduct for engineers stipulates adherence to the highest moral standards. When carrying out their obligations as engineers, they must put the safety, health, and welfare of the public first. only offer services in the specialties they are knowledgeable about.
Learn more about engineers here-
https://brainly.com/question/18564178
#SPJ4
the top floor resident and the bottom floor resident are filling their bathtubs. assuming frictionless pipes and isothermal flow, which one will fill faster?
Answers
As the water travels in a frictionless and isothermal environment, it will not lose any energy and the bottom floor resident's bathtub will fill faster than the top floor resident's bathtub.
What is isothermal?Isothermal is a term used to describe a process in which the temperature remains constant. This is typically achieved by transferring heat energy between a system and its surroundings, or by having the system be in thermal equilibrium with its surroundings. In thermodynamics, an isothermal process is a process in which the temperature of the system remains constant. This is achieved by transferring heat energy between the system and its surroundings or by having the system be in thermal equilibrium with its surroundings. An example of an isothermal process is the Joule-Thomson effect, in which a gas expands and contracts isothermally as its pressure changes.
To learn more about isothermal
https://brainly.com/question/20721364
#SPJ4
What are the limiting dimensions (height, width, and length) for individual pieces of structural steel that can be shipped by trucks on highways with no difficulty or special permitting?
Answers
This depends on the type of truck and the regulations of the specific highway.
what is dimension
Dimensions are used to refer to the physical aspects or measurements of an object. They are typically expressed as length, width and height. Length is the measure of an object from end to end, width is the measure of an object from side to side and height is the measure of an object from top to bottom. Dimensions are used in a variety of fields such as engineering, architecture, art, mathematics and science. Knowing the dimensions of an object can help to calculate its area, volume, or weight. Dimensions are also used to compare the size of objects to each other.
To know more about dimension
https://brainly.com/question/28942977
#SPJ4
calculate the net work done on the satellite as it moves once around the orbital path. submit the final answer here and show your work in your dropbox submission.
Answers
To calculate the net work done on the satellite as it moves around the orbital path, you need to calculate the gravitational potential energy of the satellite at different points in the orbit. The change in gravitational potential energy is equal to the net work done on the satellite.
To calculate the gravitational potential energy, use the following formula:
GPE = mghwhere m is the mass of the satellite, g is the gravitational acceleration, and h is the height of the satellite above the centre of the Earth.
Once you have calculated the gravitational potential energy of the satellite at different points in the orbit, subtract the initial GPE from the final GPE to calculate the net work done on the satellite. Show your work in your Dropbox submission.
Learn more about net work:
https://brainly.com/question/8118353
#SPJ4
if the average normal stress in each of the 20-mm-diameter bars is not allowed to exceed 150 mpa, determine (a) the maximum force p that can be applie
Answers
The maximum force that can be applied to a 20-mm-diameter bar without exceeding the average normal stress of 150 MPa is approximately 0.063 N.
The maximum force that can be applied (P) to a 20-mm-diameter bar can be determined using the formula for normal stress:
σ = P/A,
where σ is the normal stress, P is the force, and A is the cross-sectional area. To find the maximum value of P, we need to find the cross-sectional area of the bar.
A = πr^2,
where r is the radius of the bar. Plugging in the values,
[tex]A = π * (0.02 m)^2 = 3.14 * 0.0004 m^2.[/tex]
Since the maximum normal stress is given as 150 MPa, we can use the equation to find the maximum force:
[tex]P = σ * A = 150 MPa * 3.14 * 0.0004 m^2 = 0.063 N[/tex].
So the maximum force that can be applied to a 20-mm-diameter bar in this case is approximately 0.063 N.
You can learn more about state of stress at
https://brainly.com/question/17037331
#SPJ4
Boxes A and B are connected to each end of a light vertical rope, as shown in the following figure. A constant upward force 90.0 N is applied to box A . Starting from rest, box B descends 12.0 m in 3.50 s . The tension in the rope connecting the two boxes is 34.0 N
Answers
The force acting on box B is calculated as 4.39 kg while the force acting on box A is calculated as 7.24 kg.
What is Upward Force?Upward force may be characterized as a type of force that is significantly exerted on an object wholly or partly immersed in a fluid. This upward force is also called Upthrust.
According to the question,
The upward force is = 90 N.
Box B was placed at a distance of s = 12.0 m.
Time is taken = 3.50 sec.
The tension in the rope connecting the two boxes is = 34.0 N.
The acceleration of the box B is calculated as follows:
s = ut + [tex]\frac{1}{2} at^2[/tex].12 = 0 × t + [tex]\frac{1}{2}[/tex] × a × [tex](3.50)^2[/tex].
5.775 [tex]s^2a[/tex] = 12 m.
a = 2.07 m/[tex]s^2[/tex].
The forces on the box B are:
[tex]M_2_g-T_2 = M_2_a[/tex]
[tex]M_2(g-a) = T_2[/tex]
[tex]M_2= \frac{T_2}{g-a}[/tex]
[tex]M_2 = \frac{34 N}{9.8-2.07}[/tex] = 34/7.73 = 4.39 kg.
The force acting on box A is calculated as follows:
[tex]T_2+M_1g-F= M_1a[/tex][tex]M_1(g-a)= F-T_2[/tex]
M1 = [tex]\frac{F-T_2}{g-a}[/tex] = [tex]\frac{90N -34N}{9.8-2.07}[/tex] = 56N/ 7.73 = 7.24 kg.
Therefore, the force acting on box B is calculated as 4.39 kg while the force acting on box A is calculated as 7.24 kg.
To learn more about Upward forces, refer to the link:
https://brainly.com/question/10119978
#SPJ1
determine the torque applied to the shaft of a car that transmits 275 hp and rotates at a rate of 3000 rpm.
Answers
The torque applied to the shaft of a car that transmits 275 hp and rotates at a rate of 3000 rpm is 481.92 lbf.ft
Why is it known as torque?As a twisting or turning force, torque typically causes objects to rotate around an axis, which could be the center of mass or a fixed point. Torque is simply a force's propensity to turn or twist in physics. Torque is a term that can be referred to using a variety of different terms, including moment and moment of force. The "moment arm" or "lever arm" can refer to the separation between the force application point and the axis of rotation.
Given:
Power transmitted, P = 275 hp
= 275 × 0.746 kv
=205.15 kw
N = 3000 rmp
P = TW
= P = t- 2πN / 60
= 205.15 × 10³ = T ×(2π ×3000)/60
T = 653.01 N-m
T = 653.01 × 0.225 × 3.28 lbf.ft
T= 481.92 lbf.ft
To learn more about torque, visit:
https://brainly.com/question/19865132
#SPJ4
if your application is composed of multiple modules (programs), which of the following program processing would you recommend?
Answers
It depends on the specific requirements of your application and the type of modules you are working with.
However, in general, there are several processing approaches that can be considered, including sequential processing, parallel processing, and distributed processing. Sequential processing involves executing the modules one after the other in a linear fashion. This approach is suitable for simple applications with a small number of modules. Parallel processing involves executing multiple modules simultaneously, which can speed up the overall processing time. This approach is suitable for applications with a large number of modules and high processing requirements. Distributed processing involves distributing the modules across multiple computers, with each computer executing its own set of modules. This approach can further improve processing speed and is suitable for very large applications with high processing requirements.
Learn more about applications :
https://brainly.com/question/28650148
#SPJ4
T/F bookmark question for later a very large percentage of knowledge based careers now require skills to design and build complex databases.
Answers
True. Database design and development are essential skills for many knowledge-based careers, such as software engineering, data science, and database administration.
What is data science?Data Science is a field that uses scientific methods, processes, algorithms and systems to extract knowledge and insights from data in various forms, both structured and unstructured. It is a multidisciplinary approach that combines statistics, mathematics, machine learning, computer science, and domain knowledge. Data Science uses predictive analytics to analyze large data sets to identify patterns, trends and correlations to uncover hidden insights and to make predictions and decisions. Data Science also includes data visualization, which is the graphical representation of data to aid in understanding and decision-making. Data Science is used in many industries to solve complex problems and to gain a competitive edge.
To learn more about data science
https://brainly.com/question/29555632
#SPJ4
an ideal step-up transformer with turn ratio 1:20 is supplied with an input power of 110 w. if the output voltage is 270 v, calculate the output power (in w) and input current (in a).
Answers
Therefore, the input current is 0.122 A, and the output power is 32.94 W.
Using the turn ratio and the input voltage, which can be obtained from the input power and input current, the step-up transformer's output voltage can be calculated. Ohm's Law can be used to compute the input current. Using the input power and input current, we will first determine the input voltage:
Input Voltage (V) * Input Current = Input Power (P) (I)
Input Voltage (V) is calculated as Input Power (P) / Input Current (I)
Making the following substitutions: Input Voltage (V) = 110 W / Input Current (I)
Next, we'll figure out the input current using the turn ratio:
Input Voltage (V) * Turn Ratio equals output voltage (V) (N)
Output voltage divided by input voltage equals turn ratio (N) (V)
Input Current (I) = Output Voltage (V) / (Turn Ratio (N) * Input Voltage (V)
= 20 * Input Voltage (V) * 270 V = Input Current (I)
The input current will then be determined by substituting the computed input voltage value:
= 20 * 110 W / Input Current (I) / Input Current (I) = 270 V
= 20 * 110 W / Input Current (I) = 270 V
Input Current (I) is equal to (20 * 110 W / 270 V * I).
Input Current (I) is equal to (270 V*I) / 2200 W.
= 0.222 A is the input current (I).
Output Voltage (V) * Output Current = Output Power (P) (I)
Power Output (P) = 270 V * Current Output (I)
Output Power (P) / Output Voltage equals Output Current (I) (V)
Output Power (P) / 270 V = Output Current (I)
Power Output (P) = 0.122 A * 270 V
Power Output (P) = 32.94 W
Therefore, the input current is 0.122 A, and the output power is 32.94 W.
Learn more about current Visit: brainly.com/question/24858512
#SPJ4
Identify the tactics design for manufacture uses for communicating and highlighting the needs and limitations that process capabilities impose on product design. (check all that apply) a. Designing all assembly tasks to come from one direction.
b. Eliminating the need for specialized tools.
c. Identifying the market share of product.
d. Reducing the total number of unique parts in a product.
e. Reducing the number of fasteners used.
Answers
The tactics design for manufacture uses for communicating and highlighting are:
d. Reducing the total number of unique parts in a product.
e. Reducing the number of fasteners used.
f. Documenting the process requirements and design constraints.
g. Exploring alternative construction techniques.
h. Exploring alternative materials.
What is tactics design?
Tactics design is the process of creating a plan of action to achieve a desired outcome. It involves creating a detailed strategy, which involves analyzing a situation, identifying objectives, developing a concept, and then deciding on the best course of action. Tactics design can be used in a number of different areas, such as marketing, military operations, business strategy, or software engineering. Tactics design involves an iterative process of testing, analyzing, and refining ideas to come up with the optimal solution.
To learn more about tactics design
https://brainly.com/question/30351890
#SPJ4
Complete Question
Identify the tactics design for manufacture uses for communicating and highlighting the needs and limitations that process capabilities impose on product design. (check all that apply) a. Designing all assembly tasks to come from one direction.
b. Eliminating the need for specialized tools.
c. Identifying the market share of product.
d. Reducing the total number of unique parts in a product.
e. Reducing the number of fasteners used.
f. Documenting the process requirements and design constraints.
g. Exploring alternative construction techniques.
h. Exploring alternative materials.
metal and dirt are not considered contaminants to oil. True/False ?
Answers
False; pollutants include things like metal and dirt. In other words, used oil must become contaminated as a result of being used in order to meet the EPA's criteria.
This part of the EPA definition covers pollutants and residues produced during the handling, storing, and processing of spent oil. The physical pollutants could be dirt, sawdust, or metal shavings. Air, water, gasoline, soot deposits, and debris like engine component wear particles are typical sources of oil pollution. Each one of these things can cause the engine lubricant to degrade. Any material present in the soil that is above normally occurring levels and endangers human health is referred to as a soil contamination. For instance, certain soils naturally contain arsenic. However, if someone uses particular pesticides to spray their yard, it could contaminate the soil.
Learn more about engine here-
https://brainly.com/question/27162243
#SPJ4
Express your answer in terms of the unit vectors i, j, and k. Use the 'vec' button to denote vectors in your answers. Express your answer using three significant figures.
Answers
OK, we're clear on the rules.
-- We'll be sure and express our answer in terms of the unit vectors i, j, and k,
-- We'll use the 'vec' button to denote vectors in our answers. And ...
-- We'll express our answer using three significant figures.
Now . . . . . What's the question ?
what is the process of figuring out how to ask a research question in measureable, testable ways.
Answers
1. Identify the research topic: Start by identifying the topic or research question you want to investigate. It is important to be clear and specific in your research question.
What is investigate?
Investigate is the process of researching and analyzing information in order to answer questions or solve problems. It is a systematic effort to uncover the facts and details of a certain issue or event. It involves the collection of data, the evaluation of sources, and the analysis of evidence.
2. Define the parameters: Once you have a research question, you will need to define the parameters of your research. This means you will need to determine the scope of the project, the timeframe, and the resources you will need to complete the project.
3. Brainstorm ideas: Brainstorm different ways to ask your research question and to approach the topic. Consider different perspectives, angles, and approaches.
4. Refine your research question: Once you have brainstormed, you will need to refine your research question. Make sure that the question is specific enough and is measureable and testable.
5. Consider the data collection methods: Consider the different data collection methods that could be used to answer your research question. This could include surveys, interviews, focus groups, experiments, or observational studies.
6. Plan the research: Once you have a refined research question and data collection method, you will need to plan the research. This includes considering the timeline, budget, and resources needed to conduct the research.
7. Execute the research: Finally, you will need to execute the research. This includes collecting the data, analyzing the data, and drawing conclusions from the data.
To learn more about investigate
https://brainly.com/question/21096265
#SPJ4
a fluid flows steadily through a circular pipe of uniform cross-sectional area as shown below. if the outlet density of the fluid decreases to 1/2 of its inlet value, what happens to the average fluid velocity?
Answers
The correct answer is What happens to the average fluid velocity if the fluid's density drops to % of its input value? A) Because it must be, the velocity won't change.
Mean fluid velocity: This parameter is designed to offer the rate of mass flow through the tube, which is the flow of a mass through a surface per unit time (Bergman et al., 2011), when multiplied by the fluid density and the tube's cross-sectional area: (8.11) The analysis of fluid flows using numerical solution techniques is known as computational fluid dynamics (CFD). You can examine intricate issues involving fluid-fluid, fluid-solid, or fluid-gas interaction using CFD. The fluid's flow rate, v, is expressed as a number of metres per second (m/s). The cross-sectional area of the pipe through which fluid is flowing is denoted by the letter A. Typically, it is measured in square metres (m2)
To learn more about fluid velocity click on the link below:
brainly.com/question/17010211
#SPJ4