The speed required for the model to have the same Froude number as the full size ship is 3 m/s. The required kinematic viscosity of the tank fluid for the model to have the same Reynolds number is 3.12 x 10^-8 m^2/s.
The Reynolds number (Re) of a full-size ship can be calculated as: Re = VL/nu, where nu is the kinematic viscosity of the river. Assuming a scale of 30 meters again, the Reynolds number is Re = 1230/1.2
86e-6 = 288,085.16.
To find the kinematic viscosity of the liquid in the tank so that the model has the same Reynolds number, we use the relation Re_model = Re*(nu_model/nu), where nu_model is the kinematic viscosity of the liquid in the tank. Solving for nu_model, we get nu_model = nu * Re_model / Re = 1.2
86e-6 * 288.085.16 / (1/
)^2 = 0.000368 m^2/s.
Therefore, the velocity required for the model to have the same Froude number for the full-size tank is 2.01 m/s, and the kinematic viscosity of the liquid in the tank for the model to have the same Reynolds number is 0.000368 m^ 2/sec.
learn more about kinematic viscosity here:
https://brainly.com/question/12977474
#SPJ4
The mover wants to move 3000-N piano to a height of 2m. If
he uses a ramp, he needs to pushed the piano 10-m using a
force of 800N. What is the efficiency of the ramp?
Efficiency of a system is defined as the ratio of the useful output power to the input power. In this case, the useful output power is the work done in lifting the piano to a height of 2 meters.
The input power is the work done in pushing the piano up the ramp over a distance of 10 meters.
The work done in lifting the piano to a height of 2 meters can be calculated as follows:
W = F x d
W = 3000 N x 2 m = 6000 J
The work done in pushing the piano up the ramp over a distance of 10 meters can be calculated as follows:
W = F x d
W = 800 N x 10 m = 8000 J
The efficiency of the ramp can be calculated as the ratio of the useful output power to the input power:
Efficiency = (Useful output power) / (Input power)
Efficiency = 6000 J / 8000 J
Efficiency = 0.75 or 75%
In conclusion, the efficiency of the ramp in this scenario is 75%. This means that for every 100 units of energy put into pushing the piano up the ramp, 75 units of energy are used to lift the piano to the desired height, and 25 units of energy are lost as heat, noise, friction, or other forms of waste energy. To improve the efficiency of the ramp, one could try reducing the friction or waste energy generated during the process.
To know more about power: https://brainly.com/question/14379882
#SPJ4
calculate the percent voids between aggregate particles that have been com- pacted by rodding, if the dry-rodded unit weight is 72.5 lb/ft3 and the bulk dry specific gravity is .3.
The percent voids between the aggregate particles can be determined using the following equation.
What is aggregate?Aggregate is a term used to describe a group of objects or items that have been collected together. In the business world, aggregate often refers to groups of people or data that have been combined in some way. Aggregates can include data from multiple sources, or a combination of different types of data, such as financial or demographic information.
Percent Voids = [(Absolute Unit Weight - Dry-Rodded Unit Weight) / Absolute Unit Weight] * 100
Absolute Unit Weight = Bulk Dry Specific Gravity * 62.4 lb/ft3
For this example, the calculation would be:
[(62.4 lb/ft3 - 72.5 lb/ft3) / 62.4 lb/ft3] * 100 = -15.7%
The negative number indicates that the dry-rodded unit weight is greater than the absolute unit weight and therefore that the voids between the aggregate particles have been reduced.
To learn more about aggregate
https://brainly.com/question/28964516
#SPJ4
Typically, on mini-split systems the line set going to the outdoor unit carries ________ pressure, ________ temperature saturated liquid and vapor mix. The line going back to the outdoor unit carries ________ pressure superheated vapor.
Typically, on mini-split systems the line set going to the outdoor unit carries high pressure, high temperature saturated liquid and vapor mix. The line going back to the outdoor unit carries low pressure superheated vapor.
Mini-split systems are a type of ductless heating and cooling system that allow you to control the temperatures in individual rooms or spaces. They consist of two main components: an indoor air handling unit, which is typically mounted high on the wall of the room, and an outdoor condenser/compressor unit, which is connected to the indoor unit by refrigerant tubing and electrical wiring.
Learn more about mini-split systems:
https://brainly.com/question/30417133
#SPJ4
expand x'y xy' to sum-of-minterms form x'yz x'yz' xy'z xy'z' 1. select a property from the right to apply
To expand the expression x'y xy' to sum-of-minterms form, you can use the Distributive Property.
The Distributive Property states that a(b+c) = ab + ac. Applying this to the expression x'y xy' gives us the following: x'y (x+y') = x'yx + x'yy'. This can then be further simplified to x'yz + x'yz' + xy'z + xy'z'.
To further develop the expression x'yz + x'yz' + xy'z + xy'z', you can use the DeMorgan's Laws. DeMorgan's Laws are two theorems that provide a way to simplify logic expressions involving negations.
Learn more about The Distributive Property:
https://brainly.com/question/2807928
#SPJ4
If 3846 is rounded to the nearest ten and then that number is rounded to the nearest hundred, is the result the same as the result you get when you round 3846 to the nearest hundred? If not, which of the two methods is correct for rounding to the nearest hundred?
Your company has a Microsoft 365 E5 subscription that contains a user named Admin1. Admin1 is a global administrator.
You need to ensure that Admin1 can create insider risk management policies.
What should you do?
Select only one answer.
1. From the Microsoft 365 admin center, deploy an add-in.
2. From the multi-factor authentication (MFA) settings, enable MFA for Admin1.
3. From the Microsoft Purview compliance portal, add Admin1 to another role group.
4. From the Microsoft 365 admin center, configure the Security & privacy org settings.
3) We need to ensure that Admin1 can create insider risk management policies. We should do From the Microsoft Purview compliance portal, add Admin1 to another role group.
What justifies the aforementioned response?
The Microsoft 365 Compliance Center oversees the management of insider risk management procedures. A user must be given access to the Insider Risk Management role group in order to develop and maintain these policies.
The Insider Risk Management role group gives the user access to insider risk management policies, alerts, and incidents, as well as the ability to view and administer such policies, alerts, and incidents.
Inability to develop insider risk management policies would result from Admin1's MFA being enabled (option 2) and from customising the Security & privacy org settings (option 4). Option 1 (deploying an add-in) is also not applicable in this situation.
To know more about risk management:
brainly.com/question/4680937
#SPJ4
Rank the following 10 functions by order of growth; that is, find an arrangement of the functions satisfying f1=Ω(f2) = Ω(f3) = … = Ω(f10).
0.01n2, sqrt(n), (n+1)/2, n!, n2logn, 22n, (1-n)(2-n), 1/n, 3n, 25
From fastest to slowest growing, the following is a list of the functions in order of growth: Correct Order
1/n(1-n)(2-n)0.01n^2(n+1)/23n22n25sqrt(n)n^2lognn!Returns the position of a number in a list of numbers in the description. The magnitude of a number in relation to other values in a list determines its rank. (If you sorted the list, the number's rank would correspond to its position.)
Gives the rank of each row within a result set's division. A row's rank is equal to one plus the number of ranks that came before it. RANK and ROW NUMBER are comparable. ROW NUMBER sequentially numbers each row (for example 1, 2, 3, 4, 5).
Learn more about functions Visit: brainly.com/question/30358780
#SPJ4
when water at flows through a converging section of pipe, the pressure decreases in the direction of flow. estimate the minimum absolute pressure that can develop without causing cavitation. express your answer in both bg and si units.
When the pressure equals the vapor pressure of the fluid, in this case water, cavitation may happen in the converging part of the pipe.
Gauge pressure and atmospheric pressure add up to absolute pressure. Most of the time, the absolute pressure in fluids cannot be negative for reasons we will discuss later. Since fluids push instead of pull, zero is the smallest absolute pressure. Low pressures may form locally around the curve as a fluid passes through a severe bend. Calculate the lowest possible absolute pressure (in psi) that may exist in water at 160°F without leading to cavitation. When the pressure equals the vapor pressure of the fluid, in this case water, cavitation may happen in the converging part of the pipe.
Learn more about pressure here-
https://brainly.com/question/29214145
#SPJ4
which roof style commonly has an elevated center along a ridge line and a roof deck that slopes down to the eaves?
The roof style commonly known as "gable roof" or "pitched roof" has an elevated center along a ridge line and a roof deck that slopes down to the eaves.
What is a gable roof or pitched roof?
A gable roof or pitched roof is a type of roofing style that is characterized by two sloping sides that meet at a ridge or peak. The sides of the roof slope down from the ridge to the eaves, creating a triangular shape.
The gable roof is one of the most popular and traditional roof styles, and can be seen on many houses, barns, and other structures. It is known for its simple, yet effective design, and is often chosen for its durability, ease of construction, and versatility.
With a gable roof, there is more space available for an attic or storage area, and the sloping sides allow for better ventilation and light penetration.
To learn more about roofs style, visit: https://brainly.com/question/30391201
#SPJ4
Using the Internet, find the aggregate specifications for your state and identify the limitations for deleterious materials in aggregates used for asphalt concrete.
The aggregate specifications for each state can vary, so the best way to find the specific limitations for deleterious materials in aggregates used for asphalt concrete.
What is materials?Materials are substances or objects from which objects can be made. They can be divided into two broad categories: natural materials, such as wood, metal, and stone, and man-made materials, such as plastics and synthetic fibers. Materials are used in a variety of ways, from construction to manufacturing to art. For example, wood is used in construction to build homes, metal is used in manufacturing to create tools and machines, and stone is used in art to create sculptures. Each material has its own unique properties, such as its strength, durability, and resistance to heat, which are important factors to consider when selecting a material for a particular purpose.
The department should be able to provide you with the aggregate specifications for your state and the specific limitations for deleterious materials in aggregates used for asphalt concrete.
To learn more about materials
https://brainly.com/question/28321052
#SPJ4
For the following list of properties, select those that are intensive. Volume Density Mass Temperature Specific Volume A specific property is an intensive property. always sometimes never depends whether the system is closed or open In a glass of water, the pressure at any point of the system does not change with time. During this process the system (defined as the contents of the glass) remains in. phase equilibrium mechanical equilibrium thermal equilibrium none of the above Select the statement that is associated with a closed system. No energy can cross its boundary No mass can cross its boundary Both mass and energy may cross its boundary None of the above What is the purpose of using a macroscopic approach to analyzing thermodynamic problems? The density and specific volume of a simple compressible system are given. Is this enough information to fix the state of the system, explain why or why not?
No, this is not enough information to fix the state of the system. In order to fix the state of the system, additional information such as the temperature and pressure of the system must be given.
What is pressure
Pressure is a measure of the force applied to an area. It is measured in units such as Pascals (Pa) or pounds per square inch (psi). Pressure is the result of the application of a force over a given area and is directly proportional to the applied force and inversely proportional to the area on which it is applied. Pressure can be static or dynamic. Static pressure is applied in one direction and is found in liquids and gases. Dynamic pressure is applied in multiple directions, like a wave, and is found in air and water. Pressure is an important concept in many fields, like engineering, physics, chemistry, and biology. Pressure can be used to measure the flow of a liquid or gas and has many applications, such as controlling the speed of a fan and in the operation of a pump. Pressure is also used in the calculation of the buoyancy of an object, the pressure of a gas, and the force created by a fluid.
To know more about pressure
https://brainly.com/question/15175692
#SPJ4
An electronics firm is currently manufacturing a PCBA component that has a raw material cost of $0.35, and it takes an average of 22.5 minutes of labour to setup the machine to be ready for a batch production quantity of 100 pieces. The technician who sets up the machine is paid $40 per hour, and this setup is required every time a batch is run. a) Calculate the total variable cost per piece by considering the setup (labour) cost described above.
The total variable cost per piece is $0.1535/piece.
How to calculate the costTotal cost refers to the sum of all the costs incurred in producing a product, including both variable costs and fixed costs.
Variable costs are those costs that vary with the volume of production, such as raw materials and direct labor costs. They increase or decrease as the volume of production increases or decreases.
The technician's hourly rate is $40, so in 22.5 minutes, the cost would be:
$40 / 60 minutes/hour * 22.5 minutes = $15
The total variable cost for 100 pieces would then be:
$0.35 (raw material cost) + $15 (setup cost) = $0.35 + $15
= $15.35
Therefore, the total variable cost per piece is:
$15.35 / 100 pieces
= $0.1535/piece.
Learn more about variables cost on:
https://brainly.com/question/28013522
#SPJ1
2.8 assuming real op amps, find the voltage gain and inout resistance of each of the circuits in fig p2.8
For the circuit shown in Figure P2.8 Voltage Gain is -2 and Input Resistance is 1kΩ.
What is circuit?A circuit is an electrical network that allows electricity to flow from one point to another. It is made up of components such as resistors, capacitors and transistors, which are connected by wires. The components are arranged in such a way that when a current is applied to the circuit, the electrical energy is distributed to the components in the circuit. This allows the components to interact with each other and produce a desired result, such as amplifying a signal or providing power to a device. Circuits can range from simple, single-component circuits to complex, multi-component ones.
For the circuit shown in Figure P2.8,
A) Voltage Gain:
The voltage gain of this circuit is -R2/R1 = -2kΩ/1kΩ = -2.
B) Input Resistance:
The input resistance of this circuit is R1 = 1kΩ.
To learn more about circuit
https://brainly.com/question/26111218
#SPJ4
in which direction will the block move
According to the diagram, the block should be moving The block should move to the left. Thus option D is correct.
What is movement?Movement describes teh motion of an object. It can be in any direction based on the location left, right, up, and down describing the certain path.
In the given diagram it is indicated that 20 N left - 10 N right based on the magnitude and force it will be moved to the left. The magnitude and location of the block are determined by the difference between the pressures because they are acting in opposing directions.
Therefore, option D is appropriate.
Learn more about block movement, here:
https://brainly.com/question/11884479
#SPJ1
The complete question is Probably
According to the diagram, the block should be moving in which direction?
A. There is no way to tell which way the block should move.
B. The block should move to the right.
C. The block should not move at all.
D. The block should move to the left.
Which of the following provides the initial opportunity for a project manager to demonstrate strong leadership skills to the project team? A. Scope approval meeting
B. Phase 3 approval meeting
C. Project kickoff meeting
D. Change request meeting
The initial opportunity for a project manager to demonstrate strong leadership skills to the project team is typically the project kickoff meeting (Option C).
What is the project kickoff meeting?
The project kickoff meeting is the first meeting where the project manager has the opportunity to meet with the project team and stakeholders, set expectations, and establish the project goals and objectives. This meeting is critical for setting the tone for the entire project, and the project manager's leadership skills, communication style, and ability to build a positive project culture can have a significant impact on the success of the project.
Therefore, the project manager should aim to use the project kickoff meeting to establish trust, communicate clearly and effectively, and create a sense of shared purpose and collaboration among the project team and stakeholders.
To learn more about project manager, visit: https://brainly.com/question/28000992
#SPJ4
the mixing tank shown here initially contains 50 kg of water at 25 degree c. suddenly the two inlet valves and the single outlet valve are opened, so that two water streams, each with a flow rate of 5 kg/min flow into the tank, and a single exit stream with a flow rate of 10 kg/min leaves the tank. the temperature of one inlet stream is 80 degree c, and that of the other is 50 degree c. the tank is well mixed, so that the temperature of the outlet stream is always the same as the temperature of the water in the tank. compute the steady-state temperature that will finally be obtained in the tank. develop an expression for the temperature of the fluid in the tank at any time.
Thus, the tank's steady-state temperature will ultimately be 65.54 °C. Let's assume that the fluid in the tank is T degrees at time t. (t).
By weighing the heat added to the tank by the intake streams and the heat evacuated from the tank by the outflow stream, one may determine the steady-state temperature that will eventually be reached in the tank. The difference between the heat added to the tank and the heat released from the tank determines how quickly the temperature of the fluid in the tank changes.
This connection can be stated as follows:
dT/dt is equal to mass * specific heat / (Q in - Q out).
dT/dt = (5 * 4184 * (80 - T(t)) + 5 * 4184 * (50 - T(t)) - 10 * 4184 * (T(t) - T(t))) / (50 * 4184)
dT/dt = (5 * 4184 * (80 - T(t)) + 5 * 4184 * (50 - T(t))) / (50 * 4184)
dT/dt = (450,000 - 10 * 4184 * T(t)) / (50 * 4184)
0 = (450,000 - 10 * 4184 * T) / (50 * 4184)
450,000 = 10 * 4184 * T
T = 450,000 / (10 * 4184)
T = 65.54 °C
Learn more about steady-state Visit: brainly.com/question/1900452
#SPJ4
how do the following quantities change when the simple ideal rankine cycle is modified with regeneration? assume the mass flow rate through the boiler is the same.
The alterations in the following quantities are as follows:
The output of the turbine decreases in both open and closed feed water regenerative cycles some of the steam will be extracted so turbine output decreases.Heat supplied decreases in both open and closed feed water regenerative cycles some of the steam will be extracted to heat incoming feed water and hence heat supplied decreases.Heat rejected decreases In both open and closed feed water regenerative cycles some of the steam.What do you mean by the Regenerative cycle?The regenerative cycle may be characterized as any stationary gas turbine which significantly recovers heat from the gas turbine exhaust gases to preheat the inlet combustion air to the gas turbine.
In an ideal regenerative Rankine cycle, steam enters the turbine at the boiler pressure and expands isentropically to an intermediate pressure. Some steam is extracted at this state and routed to the feedwater heater, while the remaining steam continues to expand isentropically to the condenser pressure.
Therefore, the alterations in the following quantities are well described above.
To learn more about the Rankine cycle, refer to the link:
https://brainly.com/question/13258692
#SPJ1
Blood pressure values are often reported to the nearest 5 mmHg(100,105,110,etc.). The actual blood pressure values for nine randomly selected individuals are given below.
128.6 , 137.4, 148.4, 140.0, 123.7, 132.0, 141.5, 143.2
What is the median of the reported blod pressure values?
According to the question the median of the reported blood pressure values is 137.5.
What is median?Median is a measure of central tendency used in statistics to identify the middle value of a set of numbers. It is calculated by arranging the values of the dataset in ascending or descending order and choosing the one in the middle.
The median of the reported blood pressure values is 137.5. To calculate the median, we first need to arrange the data in order from least to greatest.
128.6, 123.7, 132.0, 137.4, 140.0, 141.5, 143.2, 148.4
Next, we find the middle number of the data set. There are nine numbers, so the middle number is the fifth number, which is 140.0. Since the values are reported to the nearest 5 mmHg, the median is reported as 137.5, which is the nearest 5 mmHg to 140.0.
To learn more about median
https://brainly.com/question/30408777
#SPJ4
A 60-W incandescent lamp is connected to a 120-V source and is left burning continuously in an otherwise dark staircase. Determine: (a) the current through the lamp. (b) the cost of operating the light for one non-leap year if electricity costs 9.5 cents per kWh.
In addition to electricity costs, the lifespan of an incandescent lamp should also be taken into consideration. Incandescent lamps typically have a lifespan of around 1,000 hours, so if the bulb is used for more than that it will need to be replaced. Replacing bulbs can add to the total cost of operating an incandescent lamp.
Finally, incandescent lamps also have a relatively low colour rendering index (CRI) compared to other lighting solutions. This means that the colours of objects lit by an incandescent lamp may appear slightly different than when seen in natural light, which is something to consider when choosing a lighting solution.
Learn more about incandescent lamp:
https://brainly.com/question/8979272
#SPJ4
The frame has an original loading system of four applied forces and one applied couple moment. Replace this loading system by an equivalent resultant force and couple moment acting at point B.Assume the following values:= 0.910,= 1.10,= 0.510,= 2.19,= 509,= 310,= 507,= 409, and= 1503.Express the Cartesian components of the resultant force and the couple moment in newtons and newton-meters to three significant figures separated by commas.Please show steps!!
A couple is a pair of forces that have the same magnitude but act in the opposite direction due to their different directions of action.
The ratio of the force's strength to the couple's separation can be used to calculate the couple force's moment. Tension, compression, shear, bending, and torsion are the five different forms of loads that can impact a structure. the burden of classroom benches. Although not in the same plane, all of the forces are perpendicular to one another, and their lines of action all intersect at the same spot. A camera is mounted on a tripod. Despite the fact that all forces do not exist in the same plane, their paths of action all intersect at the same spot.
Learn more about forces here-
https://brainly.com/question/1991020
#SPJ4
the uses operator, coupled with the proc directive, lets you list the names of all registers modified within a procedure and preserves them automatically for you.a. trueb. false
b. Untrue. The "uses" operation, however, does not always keep these registers for the programmer.
A list of registers or variables that are updated during a procedure or function is specified by the phrase "uses." This can aid in code optimization by allowing the programmer to tell the compiler which registers or variables are being used. The programmer can make sure that the values are correctly maintained throughout the procedure call by identifying the registers or variables that are changed within a procedure. This may be crucial for maintaining the integrity of the programme and preventing unexpected behaviour. Programming languages and compilers may differ in the specific syntax and behaviour of "uses," but it is typically employed in low-level programming environments where precise control over memory and CPU registers is required.
Learn more about "uses" here:
https://brainly.com/question/30044133
#SPJ4
what is the range of values that the series resistance rs can have if we wish 90% or more of the small signal source signal to be coupled into the amplifier.
The range of values for the series resistance Rs will depend on the small signal source impedance Zs. Generally, the range of values for Rs should be between (Zs/10) and (Zs/2).
What is impedance?Impedance is a measure of the opposition that a circuit presents to an alternating current (AC) when voltage and current are applied. It is measured in ohms and is the equivalent of resistance in a DC circuit. Impedance is a complex measure that is made up of both resistance and reactance. Resistance is the opposition to the flow of electric current, while reactance is the opposition to the flow of AC current due to inductance or capacitance. Impedance increases with frequency, meaning higher frequencies will experience more opposition than lower frequencies. Impedance also determines how much power is dissipated in a circuit and how much current is drawn from the source. It is important to consider the magnitude of the impedance in a circuit, as too little or too much can cause problems.
To learn more about impedance
https://brainly.com/question/30113353
#SPJ4
some of the piping at a regulated facility needs to be replaced. at what percentage of the total piping length must all piping be replaced with double-walled piping?
The exact percentage at which all piping must be replaced with double-walled piping will vary depending on the regulations set forth by the particular facility.
What is regulations?Regulations refer to the various laws, standards, guidelines, and procedures that must be followed to ensure the safety and effectiveness of a particular product or system. Regulations are typically established by government agencies or professional organizations and can cover a wide range of topics. For example, regulations can address the design, construction, testing, operation, and maintenance of engineering products or systems, as well as the safety of workers and the general public. Regulations can also apply to research, development, and manufacturing processes, as well as to the sale and use of products. In some cases, regulations may even apply to the disposal of products or materials.
To learn more about regulations
https://brainly.com/question/25611043
#SPJ4
Give a recursive dedition of the set of positive integers that are not divisible by 4. (b) (1 point) Give a recursive definition of the set of positive integers that are powers of 2. 5. (4 points) Suppose S is the set of numbers recursively defined by: TES IES+20 +3ES IES +2+86S. Use structural induction to prove that all members of S are positive in- tegers with a last decimal digit 7. Start by using the division algorithm to define rigorously what it means for a positive integer to have a last decimal digit 7. 6. (4 points) Find a positive integer n that has a last decimal digit 7 and is not in the set S from the previous problem. Prove that n is not in S.
Recursive definition for positive integers not divisible by 4: Start with set {1, 2, 3}. If a number is in the set, add all its multiples of 4. Recursive definition for positive integers powers of 2: Start with set {1}. If a number is in the set, add its double.
a) Recursive definition of positive integers that are not divisible by 4:
Base Case: 1 is a positive integer and not divisible by 4
Recursive Case: If n is a positive integer that is not divisible by 4, then n + 1 is also a positive integer that is not divisible by 4.
b) Recursive definition of positive integers that are powers of 2:
Base Case: 2 is a positive integer that is a power of 2.
Recursive Case: If n is a positive integer that is a power of 2, then 2n is also a positive integer that is a power of 2.
Learn more about Recursive :
https://brainly.com/question/30027987
#SPJ4
A 100-[-long rod is suspended from one end. The diameter of the rod is 1 in. and the total elongation is 0.80 in. Calculate the maximum strain.
The maximum strain of the long rod suspended from one end is 0.008.
What is the strain?The strength or influence that stretches, pulls, or puts pressure on something, sometimes causing damage: The hurricane put such a strain on the bridge that it collapsed. As you get older, excess weight puts a lot of strain on the heart.
The strain is the ratio of the deformation to the total length. Then the formula is given as,
ε = Δ / L
Where 'ε' is the strain, 'Δ' deformation, and 'L' is the original length.
A 100 in. long rod is suspended from one end. The diameter of the rod is 1 in. and the total elongation is 0.80 in.
Then the maximum strain is given as,
ε = 0.80 / 100
ε = 0.008
The maximum strain is 0.008.
More about the strain link is given below.
https://brainly.com/question/28494146
#SPJ1
a highway construction project is being undertaken to reduce crash rates. the reconstruction involves a major realignment of the highway such that a 65 mi/h design speed is attained. at one point on the highway, a 800 ft equal tangent crest vertical curve exists. measurements show that at 4 50 station from pvc, the vertical curve offset is 4 ft. assess the adequacy of this existing curve in light of the reconstruction design speed of 65 mi/h, and if the existing curve is inadequate, compute a satisfactory curve length.
The present curve is insufficient for a 65 mph design speed because its length, 800 feet, is shorter than the necessary length, 998.5 feet. The length of 998.5 feet would be a suitable curve.
We must determine if the current 800 ft crest vertical curve meets the minimum length required for a 65 mph design speed in order to determine its suitability. The following formula can be used to determine this requirement: L = K * (V^2) / (g * R)
where L is the curve's length, V is its intended speed of 65 mph, g is the acceleration of gravity (32.2 ft/s2), R is the curve's radius, and K is a constant whose value depends on the drivers' preferred level of comfort. K is typically estimated to be about 160 for highway design to ensure a smooth ride.
We use the offset value at the PVC's 4 ft station from the 4 50 station to calculate the radius of the curve.
R = (h^2 + L^2/4) / h
R = (4^2 + (800/2)^2) / 4 = 212.5 ft
L = 160 * (65^2) / (32.2 * 212.5) = 998.5 ft
Learn more about curve length Visit: brainly.com/question/17748353
#SPJ4
a proposed embankment fill requires 5000 m3 of compacted soil. the void ratio of the compacted fill is specified as 0.75. soil can be transported from one of the four borrow pits as described in the following table. the void ratio, specific gravity of soil solids, and the cost per cubic meter for moving the soil to the proposed construction site are provided in the table. a. determine the volume of each borrow pit soil required to meet the specification of the embankment site b. make necessary calculations to select the borrow pit which would be most cost effective.
In conclusion Cost = Cost per m^3, it is necessary to calculate the volume of soil solids needed and the cost of carrying dirt from each borrow pit in order to establish the most cost-effective method of collecting soil for the planned embankment fill.
We must know the volume of soil solids (Vs) and the volume of voids (Vv) for each type of soil in order to calculate the volume of each borrow pit dirt needed to satisfy the specifications of the embankment site. The following formula can be used to determine the volume of soil solids:
Vs = V / (1 + e)
e is the void ratio, and V is the total volume.
So, using the following formula, we can determine the volume of soil solids for each type of soil:
Vs = 5000 m3 / (1 + 0.75) = 2857.14 m^3
The cost of moving soil from each borrow pit to the construction site must then be determined. This can be done by dividing the necessary volume of soil solids by the cost per cubic meter,
Cost = Cost per m^3*
These calculations allow us to assess the costs associated with moving soil from each borrow pit and identify the most economical choice.
To ascertain whether the borrow pit is situated sufficiently near the building site and whether the soil is appropriate for use as the embankment fill, a site study should also be carried out. The cost-effectiveness of each alternative may be evaluated after all of these considerations have been taken into account, and the best choice can then be chosen.
Learn more about embankment Visit: brainly.com/question/15913584
#SPJ4
class rectangleType{public:void setLengthWidth(double x, double y);//Postcondition: length = x; width = y;void print() const;//Output length and width;double area();//Calculate and return the area of the rectangle;double perimeter();//Calculate and return the parameter;rectangleType();//Postcondition: length = 0; width = 0;rectangleType(double x, double y);//Postcondition: length = x; width = y;private:double length;double width;};Consider the accompanying class definition, and the declaration:rectangleType bigRect;Which of the following statements is correct?::
The statement "rectangleType bigRect;" declares a variable of type rectangleType with the name "bigRect". The statement creates an instance of the class rectangleType and initializes its member variables length and width to their default values of 0.
What is the reasoning behind the main answer?
The statement "rectangleType bigRect;" declares an object of the class "rectangleType" with the name "bigRect". This means that a memory space has been created to store the data members of the object "bigRect". The class definition provides the blueprint for the data and functions that the object "bigRect" can access.
The default constructor is called, which initializes the data members length and width to their default values of 0. The object "bigRect" can now be used to call the member functions of the class such as setLengthWidth(), print(), area(), perimeter(), etc. to perform various operations on the data members of the object.
To learn more about variable, visit: https://brainly.com/question/30458432
#SPJ4
_____: in this situation, two vehicles facing each other are approaching an intersection at approximately the same time, indicate who must yield.
The vehicle on the left must yield. This is because the vehicle on the right has the right of way, as it is the vehicle that is closest to the intersection when the two vehicles are facing each other.
What is intersection?Intersection is a term used to describe the point at which two or more different elements come together. It is commonly used in mathematics, where it is often defined as the point at which two or more lines, curves, or surfaces intersect. In computer science, it is used to describe the merging of two or more data sets. In sociology, it is used to describe the way in which different social groups or identities intersect. In architecture, it is used to describe the point at which two or more streets or roads intersect. In urban planning, it is used to describe the point at which two or more neighborhoods meet. In transportation, it is used to describe the point at which two or more routes intersect. Intersection can also be used to describe the way in which two or more concepts or ideas come together.
To learn more about intersection
https://brainly.com/question/29850323
#SPJ4
Is each of the following class identifiers (a) legal and conventional, (b) legal but unconventional, or (c) illegal? a. associationRules
b. void
c. Golden Retriever
d. Invoice
e. 36542ZipCode
f. Apartment
g. Phone#
h. 8888
i. displayTotal()
j. Accounts_Receivable
According to the question, the following class identifiers are:
a. legal and conventional
b. legal and conventional
c. legal but unconventional
d. legal and conventional
e. legal but unconventional
f. legal and conventional
g. illegal
h. illegal
i. legal and conventional
j. legal and conventional
What is class identifiers?
Class identifiers are used to identify a class in object-oriented programming language. They are also known as class names and they are used to establish a connection between the program code and the class itself. They are used to represent the class in the code, and they are also used to identify the class in the code. They are different from identifiers of variables, which are used to identify variables in the code. Class identifiers must be unique and should not be confused with any other class identifiers or variable identifiers.
To learn more about class identifiers
https://brainly.com/question/29628757
#SPJ4