Calculate the inductance of an lc circuit that oscillates at 120 hz when the capacitance is 8.00 f.

Answers

Answer 1

An LC circuit is a circuit that consists of an inductor (L) and a capacitor (C) connected in parallel or in series. In an LC circuit, the energy is transferred back and forth between the inductor  inductance of the LC circuit is approximately 2.64 × [tex]10^{-4} H.[/tex]

The frequency of oscillation is given by: f = 1 / (2π√(LC)) where f is the frequency in hertz (Hz), L is the inductance in henrys (H), and C is the capacitance in farads (F).

We are given the frequency f = 120 Hz and the capacitance C = 8.00 F. We can rearrange the above formula to solve for the inductance L:

[tex]L = (1 / (4π^2f^2C))\\L = (1 / (4π^2(120 Hz)^2(8.00 F)))\\L = 2.64 × 10^-4 H[/tex]

Therefore, the inductance of the LC circuit is approximately 2.64 × 10^-4 H.

Know more about capacitance here:

https://brainly.com/question/31871398

#SPJ11


Related Questions

Jordyn places a balloon near some paper scraps, but nothing happens. After Jordyn
rubs the balloon against her shirt, the paper scraps start sticking to the balloon.
Jordyn's teacher notes that there is now an electric force between the balloon and
the paper.
What could have happened when the balloon was rubbed on Jordyn's shirt to cause
this electric force?
The balloon has gained a net electric charge.
The balloon has lost its net electric charge.
The net electric charge of the balloon did not change.

Answers

A balloon absorbs electrons from a wool fabric when it is rubbed against it, leaving the balloon with a negative charge and the wool with a positive charge.

Is there static electricity in a balloon?

Electrons from the atoms and molecules in your hair migrate to the balloon when you brush it against your head. The balloon acquires a negative charge thanks to the negative charge of electrons, but your hair retains a positive charge.

Electrons migrate from the hair or wool to the balloon when the balloon is rubbed against it. The balloon picks up a net negative charge because electrons have a negative charge. The can rolls because the positive charges in the can are drawn to the negative charges in the balloon.

learn more about static electricity refer

https://brainly.com/question/18562731

#SPJ1

A car accelerates uniformly from rest and
reaches a speed of 13.9 m/s in 3.7 s. The
diameter of a tire is 85.1 cm.
Find the number of revolutions the tire
makes during this motion, assuming no slipping.
Answer in units of rev.

Answers

The number of revolutions  of the tire during the motion is 10 revolutions.

What is the number of revolutions of the tire?

The number of revolutions  of the tire during the motion is calculated from the distance travelled by the tire.

The total distance travelled by the tire during the motion is calculated as follows;

s = t ( u + v ) / 2

where;

u is the initial speed of the carv is the final speed of the cart is the time of motion

s = 3.7 x ( 13.9 + 0 ) / 2

s = 25.72 m

The number of revolutions of the tire is calculated as follows;

N ( 2πr ) = 25.71

where;

r is the radius of the tire

N = ( 25.71 ) / ( 2π x 0.4255 )

N = 9.6 ≈ 10 rev

Learn more about number of revolutions here: https://brainly.com/question/20700248

#SPJ1

Alternative energy sources like solar and wind power _______. A. Are always available b. Are only replenished with human intervention c. Are renewable d. Are more versatile than fossil fuels please select the best answer from the choices provided a b c d.

Answers

Alternative energy sources like solar and wind power are always available option A is the correct answer.

How many different kinds of alternative energy are there?

In addition to the seven energy sources mentioned above, other alternative energy sources include geothermal energy, wave energy, hydroelectric energy, solar thermal energy, and even space solar energy. Geothermal energy is generated within the earth and is used, unlike wave and hydroelectric energy uses the power of water.

Does solar power have a finite or infinite supply?

There will never be a shortage or shortage of solar energy because it is one of the cleanest and most plentiful renewable resources. Every person on the planet might theoretically have access to energy for a year with just one hour of sunlight shining on the earth's atmosphere.

To know more about Alternate energy visit

brainly.com/question/3758506

#SPJ4

You throw rocks repeatedly into a lake and make waves. If you throw rocks more frequently, what happens to the waves? Why?

Answers

If you throw rocks more frequently into a lake, the waves will become more frequent and closer together. This is because throwing the rocks more frequently increases the rate of disturbance in the water, leading to more waves being created.

What is the rocks  distance about?

As you throw rocks more frequently into the lake, the water molecules in the lake will be disturbed more often and at a faster rate.

These disturbances create waves on the surface of the water, which are essentially the transfer of energy through the water molecules. When the rocks are thrown more frequently, more energy is added to the lake at a faster rate, which results in more waves being created.

Due to the above, the distance between the waves will decrease and the amplitude of the waves will likely be the same. This is due to the fact that the rate of disturbance is increased and therefore more energy is added to the system and the waves are created more frequently.

Learn more about rocks from

https://brainly.com/question/398139

#SPJ1

A 0.2 kg ball is caught in a 0.5 kg glove. The ball had been moving at 8.0 m/s and it required 5.0 N of force to stop it. What was the force on the glove?

Answers

The force on the glove is 12.8 N.

Solving for the  force on the glove:

The force on the glove is equal to the impulse (change in momentum) experienced by the ball divided by the time over which the force was applied.

Impulse = force x time

              = 5.0 N x (1/8.0 m/s)

Impulse = 0.625 Ns

The change in momentum of the ball ΔP is

ΔP =  m x v

where,

m = is  the mass of the ball

v= its velocity

Momentum = mass x velocity

                   = 0.2 kg x 8.0 m/s

Momentum= 1.6 kg m/s

The force on the glove is equal to the change in momentum divided by the time over which the force was applied:

Force = change in momentum/time

           = 1.6 kg m/s

               (1/8.0 m/s)

Force = 12.8 N

Learn more about momentum and force on

https://brainly.com/question/29021338

#SPJ1

Leilani has struggled with body distortion for a while. She is so unhappy with how she imagines that she looks that she does not even want to leave
the house or hang out with her friends. In fact, if she can avoid being in public, she does. She just wants to stay in her room. What is the BEST
description of the effect that her body distortion is having?
A. dyslexia
B. anorexia
C. depression
D. suppression

Answers

The BEST description of the effect that her body distortion is having is (C) depression.

What is depression?

Depression is a mental health disorder characterized by a persistent feeling of sadness, hopelessness, and loss of interest in activities. People with depression may experience changes in sleep, appetite, energy level, and concentration. Additionally, they may experience feelings of guilt, worthlessness, and helplessness. Symptoms of depression can range from mild to severe and can include physical symptoms such as fatigue, headaches, and stomachaches. Psychotherapy, medication, and dietary changes were available treatments for depression. With the right support and treatment, individuals can lead a healthy and fulfilling life.

To learn more about depression
https://brainly.com/question/10045613
#SPJ1

Dipole-dipole forces are considered the most important forces in polar substances because the London dispersion forces

Answers

They are attractive forces between two permanent dipoles, or two induced dipoles.

What is dipoles?

A dipole is a type of electrical charge consisting of two equal and oppositely charged poles, or points of charge. The two poles are usually represented by a positive and negative sign. Dipoles are commonly found in molecules, atoms, and other types of particles, and are responsible for many of the physical and chemical interactions we observe in nature. Dipoles can also be created artificially with electrical equipment, such as in the case of an electric dipole antenna, which is used to transmit or receive radio signals. In a dipole, the two charges attract each other, which creates a field of force between them. The strength of this field depends on the distance between the two charges. Dipoles also exist in a magnetic form, in which the two poles have opposite magnetic poles and create a magnetic field.

This type of intermolecular force is a type of Van der Waals force and is much stronger than the London dispersion forces. They are responsible for most of the physical properties of polar substances, such as boiling points, melting points, and solubility.

To learn more about dipoles
https://brainly.com/question/14553213
#SPJ4

1. write true or false

Centrifuge works on centripetal force
b. separating funnel is used to separate blood cells from blood samples
c. Rotors are used in physical separation of a solid and a liquid.
d. Centrifuge is used to separate suspended particles from suspension
e. Milk and water are separated by using separating funnel
f. The role of condenser is connected to hot water supply

Answers

Answer:

a

true

true

true

true

true

true

true

p
4. Which of the following statements is not accurate regarding identifying factors on the health pyramid?
All three sides of the health triangle affect each other.
Personal actions are categorized on the health pyramid by the intended purpose of the initial actions.
Physical health is the base of the triangle and is the most important part of the health triangle.
Working out a gym would be categorized in the physical health category.

Answers

Pyramid collision, recommendations are made specifically for each person depending on their age, gender, and amount of physical activity. The consumption of cereals,  milk, veggies, fruit, and oils are the main.

A health impact pyramid: what is it?

The Health Benefit Pyramid is a diagram that shows the many levels of impact that can come from interventions in public health. Attempts to deal with the social determinants that potentially affect your health are at the bottom of the pyramid, suggesting interventions with the highest potential impact. Housing, financial stability, public safety, jobs, education, and the environment are a few examples of these. The broader determinants of health are these.

What are the four primary categories of factors that affect health?

Numerous variables affect health, including These circumstances are referred to as social determinants, which are the socioeconomic factors that influence life expectancy and quality of life and support health. Examples of these factors include accommodation, education, access to food, and transportation. Too frequently, people lack control over their ability to access these resources that influence their health.

To know more about collision visit :

brainly.com/question/4322828

#SPJ1

Can someone write 2-3 sentences about waves. (Transversal waves, Wavelength, Longitudinal waves.)

Answers

The answers include the following below:

Transversal waves - This is the type of wave whose oscillations are perpendicular to the direction of the wave's advance.Wavelength - This is the distance between corresponding points of two consecutive waves.Longitudinal waves - This is the type of wave in which the vibration of the particles takes place in the same direction as that of the wave.

What is a Wave?

This is referred to as the propagation of disturbances from place to place in a regular and organized way and there are different types of waves.

An example is the longitudinal wave which has the vibration of the particles takes place in the same direction as that of the wave.

Read more about Wave here https://brainly.com/question/25699025

#SPJ1

1. Benefits of Renewable Energy?
2. Renewable Energy Today?
3. Using Biomass as an Energy Source?

Answers

Answer:

1.Benefits of Renewable Energy Use

Less global warming.

Improved public health.

Inexhaustible energy.

Jobs and other economic benefits.

Stable energy prices.

2.Hydroelectric generation at scale dates back more than a century, and is still our largest renewable source – excluding traditional biomass, it still accounts for more than 60% of renewable generation

3.Biomass can be burned to create heat (direct), converted into electricity (direct), or processed into biofuel (indirect). Biomass can be burned by thermal conversion and used for energy

Which object(s) formed last in our solar system?the sunthe solar nebulathe inner planetsthe planetesimals.

Answers

The planetesimals, which are small bodies that eventually formed into larger objects such as planets, are believed to have formed last in our solar system.

Our solar system formed around 4.6 billion years ago from a cloud of gas and dust, known as the solar nebula. The sun formed first from the dense, hot center of the nebula. As the sun formed, it began to emit heat and radiation, which caused the remaining gas and dust to begin to condense and form into small objects known as planetesimals.

As these planetesimals collided and merged, they grew larger and larger, eventually forming the inner planets, such as Mercury, Venus, Earth, and Mars. The outer planets, such as Jupiter and Saturn, also formed from the collision and merger of planetesimals, but they formed later in the process.

To learn more about planetesimals visit: https://brainly.com/question/10337322

#SPJ4

Your question seems incomplete, but I assume the question was:

"Which object(s) formed last in our solar system?

the sun

the solar nebula

the inner planets

the planetesimals."

Which is defined as the statement that answers the scientific problem based on the results of the experiment?

Answers

Conclusion statement defines the answer of a scientific problem based on the result of the experiment.

A scientific problem is solved by the scientific methods. A scientific method is the step-by-step approach to a conclusion of the problem. It may include the following steps.

Observation: It is the first step of the method. It is based on that how do you see the problem.

Hypothesis: It is the result you think that you will get.

Prediction: It is based on your scientific knowledge. If our hypothesis is correct than our prediction will also be true.

Experiment: It is the system or mechanism designed by you to test your hypothesis.

Conclusion: It is the final result based on the experiment of the method. This statement tells you whether your hypothesis is true or not.

To know more about Conclusion, here

https://brainly.com/question/78686  

#SPJ4

hat conditions are necessary for a partial solar eclipse? what conditions are necessary for a partial solar eclipse? first or third quarter moon at a node new moon on ecliptic, with us in the penumbral shadow full moon at apogee full moon on equator, with us in the umbral shadow new moon at perigee

Answers

Answer:

An eclipse of the sun must occur at a "new" moon - when the moon is between the earth and the sun.

The word penumbra refers to a "partial" eclipse as opposed to umbra which refers to total eclipse.

A partial eclipse must include both terms - "new" and "penumbra"

When reggie stepped up to the plate and hit a 0. 150-kg fast ball traveling at 36. 0 m/s, the impact caused the ball to leave his bat with a velocity of 45. 0 m/s in the opposite direction. If the impact lasted for 0. 002 s, what force did reggie exert on the baseball?.

Answers

When reggie stepped up to the plate and hit a 0. 150-kg fast ball traveling at 36. 0 m/s, the impact caused the ball to leave his bat with a velocity of 45. 0 m/s in the opposite direction. If the impact lasted for 0. 002 s, the force did reggie exert on the baseball is 6075 N.

The force can be calculate as follows:

assuming that the ultimate direction of motion is positive and the starting direction of motion before to impact is negative.

m = 0.15 kg, or the mass of the ball being struck

v0 is the ball's pre-impact initial velocity and is equal to 36 m/s.

45 m/s is the ball's final speed after impact, or v.

Time of Impact: 0.0020 seconds

Reggie's force on the ball was F.

Incorporating impulse-change into the momentum equation

F t = m (v - v₀)

F (0.0020) = (0.15) (45 - (- 36))

F = 6075 N

Learn more about force at https://brainly.com/question/13976717

#SPJ4

A 12 kg sled slides down a hill and collides inelastically with an 8 kg block at rest at the bottom of the hill (the sled and block stick together). There is no friction on the hill but the coefficient of friction on the flat ground is µ = .75. The sled and block slide for 2.5 meters along the flat ground before stopping. Calculate the following:
1. What is the frictional force between the sled & block (stuck together) and the flat
ground?

Answers

Answer:

To calculate the frictional force between the sled & block (stuck together) and the flat ground, we can use the equation:

friction = friction coefficient * normal force

The normal force is equal to the gravitational force acting on the combined mass of the sled and block, which is 12 kg + 8 kg = 20 kg. The gravitational force is equal to the mass multiplied by the acceleration due to gravity (g = 9.8 m/s^2).

So the normal force = 20 kg * 9.8 m/s^2 = 196 N

The coefficient of friction (µ) is given as 0.75. So the frictional force is:

friction = 0.75 * 196 N = 147 N

So the frictional force between the sled & block (stuck together) and the flat ground is 147 N.

Note that in calculating the normal force, we are assuming that the sled and block are moving as a single unit and therefore the force is acting on their combined mass. Also the force is calculated on the basis of friction coefficient which is given as 0.75

Answer:

Explanation:

The frictional force between the sled and block (stuck together) and the flat ground can be calculated using the formula:

friction = coefficient of friction * normal force

The normal force is the force exerted on an object perpendicular to the surface it is in contact with, and it can be calculated by using the weight of the object (mg). In this case, the weight of the sled and block (stuck together) is 12 kg + 8 kg = 20 kg. So, the normal force is 20 kg * 9.8 m/s^2 = 196 N.

Using the coefficient of friction provided (µ = .75), we can calculate the frictional force as:

friction = .75 * 196 N = 147 N.

So, the frictional force between the sled and block (stuck together) and the flat ground is 147 N.

2. A barista uses the expression 4.25v + 2.65g to calculate her profit when she sells v, ven
and g, grande, beverages. What is the barista's profit, in dollars, when she sells 36 venti an
44 grande beverages?

Answers

It’s a I just took the test

Man pushes a shopping cart to the right with 93 N of force and travel 23 m to tge right how much work is done on shopping cart ?

Answers

Go 54 N travel I took test

What happens when a falling object reaches terminal velocity?
it slows down.
it stops accelerating
It speeds up
it hits the ground and stops.

2. How does a falling object’s surface area affect calculations of terminal velocity?
The greater the objects surface area, the more air resistance it encounters
The greater the objects surface area, the greater the air density
Surface area does not affect an object’s terminal velocity
The greater the object’s surface area, the greater it’s terminal velocity

Answers

When the object reaches the terminal velocity the object stops accelerating. Option B

The greater the objects surface area, the more air resistance it encounters. Option A

What is the terminal velocity?

Terminal velocity is the maximum velocity an object reaches when falling through a fluid, such as air, due to the balance of gravitational force and fluid drag.

Surface area affects terminal velocity because a larger surface area results in greater fluid drag force, which slows the object's descent. A smaller surface area results in less fluid drag and a higher terminal velocity.

Learn more about terminal velocity:https://brainly.com/question/2654450

#SPJ1

What was the hypothesis of Gregor Mendel?

Answers

The Hypothesis of Gregor Mendel are:

Pairs of distinct physical components are responsible for determining each characteristic (now called genes).During the process of gamete creation, gene pairs become physically distinct from one another (Law of Segregation).There is a possibility of having two, three, or even more variants of a gene (alleles).Sometimes one allele, which is referred to as the dominant allele, can hide the expression of the other allele, which is referred to as the recessive allele.Organisms that are capable of true breeding have two copies of the same allele (homozygotes), while hybrids have two copies of alleles that are different (heterozygotes).Chance plays a role in deciding which of two members of a pair of genes will be included in a gamete (Law of Independent Assortment).

GREGOR MENDEL IMPACT

Mendel's work with his signature peas led to the description of the rules of heredity and the invention of the phrases dominant, recessive, and discrete factor (Orel 1984), which predated the concept of gene (Pisum sativum).

Working with pea plants, Gregor Mendel uncovered the rules of heredity. He reasoned that genes must exist in pairs since each child receives a set of DNA from both parents. Mendel observed how qualities from both parents may show up in offspring, and how they would be passed down as either dominant or recessive.

Learn more about Gregor Mendel here:

https://brainly.com/question/11343026

#SPJ4

How does weathering and erosion work together to shape the earth

Answers

Answer:

is d

Explanation:

how does resistance change with charge density?

Answers

The resistance would increase when the charge density increases.

What is the resistance?

We have to note that when we talk about the resistance, we mean the opposition that is offered to the flow of current in the circuit. Let it be known that the resistance would be seen to increase as the charge density is increasing. The reason why this is going to occur is that we are going to have a lot of charges that are migrating at the same time and as such the rate of the movement of the charges or their speed would be slowed down.

If on the other hand, we see that the charge density is low, we are going to have less charges and they are going to move more freely and the resistance or the opposition to the movement of the charges would be lower.

Learn more about resistance:https://brainly.com/question/11431009

#SPJ1

A hollow steel tube with an inside diameter of 100mm must carry a tensile load of 400 kn.

Answers

The outer diameter of a hollow steel tube when the stress is limited to 120 MN/m² is  119.35 mm

Axial stress refers to the stress induced in a loaded member along the longitudinal or axial member direction. Calculated mathematically from the ratio of the axial or longitudinal force to the cross-sectional area of ​​the member.

Using the expressions for the axial stress and rated load, the cross-sectional area of ​​the tube can be determined. Substituting the values ​​for the cross-sectional area of ​​the tube and the inside diameter of the tube in the expression for the cross-sectional area of ​​a hollow cylinder yields the outside diameter of the tube.

                                σ = F/A

The formula for calculating the cross-sectional area of ​​a hollow cylinder.

A = π/4(D² – d²)

Here, the inside and outside diameters of a hollow cylinder are d and D.

Step 1

Determine the cross-sectional area of ​​tube (A) using the axial stress expression:

σ = F/A

Here, the axial stress limit is σ = 120 MN/m2 and the tensile load is F = 400 kN

σ = F/A

120 x 10³KN/1 MN = 400 kN/A

A = (400 kN) ÷ (120 x 10³ kN/m²)

A = 3333.33 mm²

Substitute the values ​​for the cross-sectional area of ​​the cylinder and the inside diameter of the cylinder in the equation for the cross-sectional area of ​​the hollow cylinder to calculate the outside diameter of the cylinder.

A = 3333.33 mm²

d = 100 mm

A = π/4(D² – d²)

3333.33 mm² = π/4(D² – 100²)

D² =[tex]\sqrt{ 14244.128}[/tex]

D = 119.35 mm

So, the outside diameter of the hollow is 119.35 mm.

Complete the questions is:

A hollow steel tube with an inside diameter of 100 millimeters must carry a tensile load of 400 kN. What is the outside diameter of the tube if the stress is limited to 120 MN/m²?

Learn more about the axial stress at https://brainly.com/question/7013119

#SPJ4

A lens produces a real image of a real object.
a) Is the image inverted or upright?
b) Is the lens diverging or converging?
c) Is the image enlarged or reduced in size?
d) If two convex lenses identical in size and shape aremanufactured from glass with two different indices of refraction,would the focal length of the lens with the greater index ofrefraction (lens 1) be larger or smaller than that of the otherlens (lens 2)?

Answers

The image is inverted, the lens is converging, the image is enlarged in size, the focal length of the lens with the greater index of refraction(lens 1) will be smaller than that of the other lens(lens 2).

A real image is that which can be obtained on the screen whereas a virtual image cannot be. A concave lens always produces virtual image whereas a convex lens can produce both real and virtual image. So the lens is convex lens which is also called converging lens. A converging lens always produces enlarged or the same size image but never produce smaller image. So the image will be enlarged in size.

The refractive index of a glass is the measure of light bending ability of it. Greater the refractive index more will be the bending of a light ray. So, if two convex lenses identical in size and shape are manufactured from glass with two different indices of refraction, the focal length of the lens with greater refractive index would be smaller.

To know more about focal length, here

https://brainly.com/question/29870264

#SPJ4

Ethan is 1. 85 meters tall. At 10 a. M. , he measures the length of a tree's shadow to be 28. 45 meters. He stands 24. 3 meters away from the tree, so that the tip of his shadow meets the tip of the tree's shadow. Find the height of the tree to the nearest hundredth of a meter.

Answers

Ethan is 1. 85 meters tall. At 10 a. M. , he measures the length of a tree's shadow to be 28. 45 meters. He stands 24. 3 meters away from the tree, so that the tip of his shadow meets the tip of the tree's shadow.  the height of the tree to the nearest hundredth of a meter is 12.68  meters

As a result, using the definition of proportion,

Tree: ethan = ethan shadow: Tree shadow

If you replace all the values, you get;

x / 1.85 = 28.45 / (28.45 - 24.3)

x / 1.85 = 28.45 / 4.15

x = 1.85*28.45 / 4.15

x = 12.68 m (rounded)

Consequently, the tree's height will be;

12.68  meters

Your question is incomplete but most probably your full question attached below

Learn more about height at https://brainly.com/question/26417592

#SPJ4

Who deals with the cosmos order?

Answers

Answer: Cosmology

Explanation:

Instructions for finding a buried treasure include the following: Go 779.7 paces at 288◦ , turn to 132◦ and walk 266 paces, then travel 115 paces at 75◦ . Find the magnitude of the resultant displacement from the starting point. Answer in units of paces. Answer in units of paces

Answers

Answer :

after this all u can write this

5) Calculate the moment caused by a 2 kg mass placed at a distance of 0.5 m to the left of the pivot. Is this
moment clockwise, or anti-clockwise? (2 marks)

Answers

The moment caused by the 2 kg mass placed at a distance of 0.5 m to the left of the pivot is 1 kg m. This moment is anticlockwise.

What is moment ?

Moment is a physical parameter equal to the product of the distance or displacement and another physical quantity such as mass, force etc.

For a mass of 2 kg and distance of 0.5 m the moment is  :

moment = mass × distance

= 2 × 0.5 = 1 kg m

If we are taking the moment of force, then it the product of the distance and force acting on the body is taken.

force = mg

F =  2 kg × 9.8 m/s² = 19.6 N

then moment of force = 19.6 N × 0.5 m = 9.8 N

The moment from left to right in direction is anticlockwise.

Find more on moment:

https://brainly.com/question/16755013

#SPJ1

How to calculate the energy tranformed from the water in the kettle to the urrounding in 2 hour i 4600 J when the ma i 0. 50kg heat capacity i 4200 J/kg and initial temperature i 100°

Answers

The energy transformed from the water in the kettle to the surrounding water loses 4200 J/kg °C * 0.5 kg = 2100 J/°C.

As it's lost 46,200 J in total (regardless of the time it took for this to happen), it must have reduced in temperature by 22 degrees. Assuming 100°C initially, temperature of water in kettle is now 78°C.

The purpose of this experiment is to determine the specific heat of two metal blocks. In one of these measurements you will also investigate the use of Newton's Law of Cooling to calculate a cooling correction. The units of specific heat in SI are J / kg ˚C.

When a body of mass M at temperature T1  receives an amount of heat (or energy) Q, its temperature may increase from T1 to T2. The heat capacity C of a body is the amount of heat required to raise its temperature by one (Kelvin) degree.

To know more about energy transformed here

https://brainly.com/question/26547865

#SPJ4

What’s the first step you should take wen working to create a work life balance

Answers

The steps to achieve a work-life balance, one should manage their time well, establish limits, pay attention to their health, and enjoy their work.

How can one balance work and life?

The state of equilibrium where a person equally priorities the responsibilities of their career and their personal life is known as work-life balance. Because both are significant, neither should be ignored. Common causes of a bad work-life balance include the following: expanded obligations at work. putting in more hours.

How do employees respond to work-life balance?

An ACAS analysis on work-life balance and flexible working shown how a poor balance can cause absences, poor productivity, and stress. Strict regulations, an excessive workload, a hostile work environment, deadline pressure, and a lack of job security are some organisational variables that interfere with work-life balance.

Learn more about work-life balance here:

brainly.com/question/6842966

#SPJ1

Other Questions
In ABC , point D lies on AC , point E lies on BC , and DEAB . Why do you think We Wear the Mask is the title of the poem? What human activity contributes to air pollution construction reforestation? Write the inequality represented on each graph. Use n for the variable. If a chromosomal segment is turned around 180, the chromosomal mutation is termed a(n)- translocation.- duplication.- deletion.- inversion.- monosomy. Solve r-4 Explain why the initial value of any function of the form f(x) = a(bx) is equal to a How much interest will Hannah earn in four years if she deposit $630 in a savings account at 6.5% simple interest? What is a good example of dramatic irony? explain the role of participation as a key element of marketing. Find the value of 7u +6 given that 3u-8=4.simplify your answer as much as possible. What is the additive inverse of _2 3? Evan and Jeremy are identical twins. Evan is very athletic and plays multiple sports. Jeremy is more into video games and spends most of the day indoors. How will their water needs differ? Below you are given a partial Excel output based on a sample of 25 observations. Coefficients Standard Error Intercept 145 29 x1 20 5 x2 18 6 x3 4 4 The estimated regression equation is _____. a. y = 0 + 1x1 + 2x2 + 3x3 + b. E(y) = 0 + 1x1 + 2x2 + 3x3 c. = 29 + 5x1 + 6x2 + 4x3 d. = 145 + 20x1 18x2 + 4x3 If f(x) = 2 + | x-3 | for all x, then the value of the derivative f'(x) at x = 3 is. 1) Which of the following relations are functions? How is language acquired Which quotation supports the idea that the narrator is discouraged about his own actions with his watch ? Appliance World places a markup on a washer/dryer combination of $295.00, which is 35%based on cost. Find the cost, then the selling price. What is the selling price of the washer/dryer? $1,098.74 $1,137.86 $1,032.19 $1,059.43 In what ways did Joseph Pulitzer and William Randolph Hearst contribute to the creation of mass culture? Their newspapers publicized the economic inequalities of the Gilded Age. Their newspapers made widespread advertising possible. Their newspapers were filled with sensational stories designed to get the widest possible readership. Their newspapers focused primarily on accurately reporting the news.