Answer: The type of solvent that should be dried with calcium chloride is esters while magnesium sulfate is diethyl ether
Explanation:
Drying agents are mainly hygroscopic substances that has the ability to absorb water on exposure to the atmosphere but not enough to form solutions. They are used in desiccators. Examples of drying agents include:
--> CALCIUM CHLORIDE: This is a compound of calcium that is found in soil water and sea water. It is prepared by the action of dilute hydrochloric acid on calcium trioxocarbonate(IV). The anhydrous salt is used in drying a wide variety of solvent including esters.
--> MAGNESIUM SULFATE: This is a slightly acidic drying agent. It works well in solvents like diethyl ether. It is a fast drying agent because it comes as a fine powder with a large surface area.
Determine whether methylcyclohexane contains a chiral center. _____ How many different substituents do you count at atom
Answer:
methylcyclohexane does not possess a chiral center
Explanation:
A molecule is said to possess a chiral center if one or more of the atoms in the molecule is bonded to four different atoms or groups.
If we look at methylcyclohexane, none of the carbon atoms in the molecule is bonded to four different atoms or groups hence the molecule contains no chiral centers and will not exhibit optical isomerism.
So, methylcyclohexane has a plane of symmetry thus it is an achiral molecule.
300.0 mL of a 0.335 M solution of NaI is diluted to 700.0 mL. What is the new concentration of the solution?
Answer: The new concentration of the solution is 0.143 M.
Explanation:
Given: [tex]V_{1}[/tex] = 300.0 mL, [tex]M_{1}[/tex] = 0.335 M
[tex]V_{2}[/tex] = 700.0 mL, [tex]M_{2}[/tex] = ?
Formula used is as follows.
[tex]M_{1}V_{1} = M_{2}V_{2}[/tex]
Substitute values into the above formula as follows.
[tex]M_{1}V_{1} = M_{2}V_{2}\\0.335 M \times 300.0 mL = M_{2} \times 700.0 mL\\M_{2} = 0.143 M[/tex]
Thus, we can conclude that the new concentration of the solution is 0.143 M.
Where do reactions in a solid
generally take place?
A. All throughout the solid
B. At the center of the solid.
C. Only on opposite sides of the solid
due to repelling forces.
D. On the surface of the solid.
Answer:
A
Explanation:
because solid stick together like magnetic and can feel every vibration
Answer:D
Explanation: on the surface of a solid
Nickel + oxygen = nickel oxide. What is the balanced redox reaction?
Answer:
This is an oxidation-reduction (redox) reaction:
2 Ni0 - 4 e- → 2 NiII
(oxidation)
2 O0 + 4 e- → 2 O-II
(reduction)
Ni is a reducing agent, O2 is an oxidizing agent.
Name the following aldehyde PLEASE PLEASE HELP
Answer:
Explanation:
Answer is D 2,5-dimethylheptanal
You should accern the lowest possible number close to the parent name
which selection is an example of an electrolyte
a. potassium iodide in water
b. sucrose in water
c. pentane in octane
d. methanol in water
Answer:
i believe its A, potassium iodide in water
Explanation:
what is the molar masses for C8H10N2O4
Answer:
198.2 g/mol
Explanation:
C = 12.01 g/mol
H = 1.01 g/mol
N = 14.01 g/mol
O = 16.00 g/mol
(12.01 x 8) + (10 x 1.01) + (14.01 x 2) + (16.00 x 4) = 198.12 g/mol
Identify the statements that correctly describe the saturation temperature of a solution.
A. Any temperature at which the solution is liquid.
B. Any temperature at which all of the compound is solid.
C. The temperature at which solid begins to appear from a cooled solution.
D. The temperature at which the Ksp value can be calculated.
Write the number of sig. fig. in four numbers given in the sentence below. An (one) octopus has 8 legs. 13 octopi have 104 legs.
Give four answers.
A. Infinity, Infinity, Infinity, Infinity
B. 1, 1, 2, 3
C. Infinity, Infinity, 2, 3
D. No answer text provided.
Answer:
1, 1, 2, 3
Explanation:
The numbers 1 and 8 both have 1 sig. fig.
The number 13 has 2 sig. figs.
The number 104 has 3 sig. figs.
In some sheep, the presence of horns is produced by an autosomal allele that is dominant in males and recessive in females.A horned female is crossed with a hornless male. One of the resulting F1 females is crossed with a hornless male. What proportion of the male and female progeny from this cross will have horns?(5 marks)
Answer:
1/2 f1 will cross
Explanation:
answer it
An electron-dot structure is a convenient method of representing
A. The complete electron configuration of the atom.
B. all electrons of the atom.
C. valence electrons of an atom.
D. core electrons of an atom.
Answer:
all electrons of the atom
PLEASE HELP FAST!!
Which of the following ions is formed when an acid is dissolved in a solution?
H+
O−
OH−
SO42+
Answer:
H+
Explanation:
acid produce H+ when it is dissolved in a solution
Predict the products of below reaction, and whether the solution at equilibrium will be acidic, basic, or neutral.
N2O5 + 3H2O → __________
Answer: The product of the given reaction is [tex]HNO_{3}[/tex] and the solution at equilibrium will be acidic.
Explanation:
When two or more chemical substances react together then it forms new substances and these new substances are called products.
For example, [tex]3N_{2}O_{5} + 3H_{2}O \rightarrow 6HNO_{3}[/tex]
This shows that nitric acid [tex](HNO_{3})[/tex] is the product formed and it is an acidic substance.
Hence, the solution at equilibrium will be acidic in nature.
Thus, we can conclude that the product of the given reaction is [tex]HNO_{3}[/tex] and the solution at equilibrium will be acidic.
In an exothermic chemical reaction:____.
A. The mass of the products is greater than the mass of the reactants.
B. The mass of the products is less then the mass of the reactants.
C. Heat is released as the reaction proceeds.
D. Heat is absorbed as the reaction proceeds.
Answer:
C
Explanation:
Think of 'exo' as exit and 'thermic' as relating to thermal energy/ heat. Thus, an exothermic release thermal energy as the reaction proceeds.
In an exothermic reaction, the total energy of the products is lesser than that of the reactants and ΔH (change in energy) is less than zero.
When heat is absorbed as the reaction proceeds, the chemical reaction is an endothermic reaction.
Rank each of the following gases in order of increasing urms assuming equivalent amounts and all gases are at the same temperature and pressure where 1 has the lowest urms and 4 has the highest urms.
a. Gas 1 : H2S
b. Gas: He
c. Gas 3: NF3
d. Gas 4: H2O
The Urms refers to the root mean square speed of the gas. The order of increasing Urms for the gases shown in the question; NF3 < H2S < H2O < He.
What is the Urms?The Urms refers to the root mean square speed of the gas. This is ultimately dependent on the relative molecular mass of the gases when they are maintained at the same temperature.
Now, let us look at the order of increasing Urms for the gases shown in the question; NF3 < H2S < H2O < He.
Learnmore about Urms: https://brainly.com/question/365923
which of the following is not an instance of benefit in from gases ?
1) filling thermometers
2) inflating tyres
3) in LP gas cylinders
4) in pressure cookers
Answer:
1) filling thermometers
Explanation:
thermometers are filled with liquid mercury
According to the kinetic-molecular theory, gas molecules have
ANSWER:
Part
A. Less energy than molecules of a solid.
B. strong interactions between molecules.
C. little distance between molecule
D. weak interactions between molecules.
Answer:
The choose ( D )
weak interactions between molecules.
Answer:
Explanation:
el a
(URGENT!) Which of these graphs best models the waves in the four locations?
(100 points)
i can not understand the question. There seems to be missing info
Para formar bronce, se mezclan 150g de cobre a 1100°C y 35g de estaño a 560°C. Determine la temperatura final del sistema.
Dato: Ce Cu: 0,093 cal/gºC; Ce Sn: 0,060 cal/gºC
Answer:
[tex]T_F=1029\ºC[/tex]
Explanation:
¡Hola!
En este caso, dada la información, es posible determinar que la temperatura del sistema estará entre 560 °C y 1100 °C, por lo tanto, se hará necesario establecer la suma de la energía del cobre y del estaño como cero:
[tex]Q_{Cu}+Q_{Sn}=0[/tex]
Así, podremos escribir esta ecuación en términos de masas, calores específicos y temperaturas como sigue:
[tex]m_{Cu}C_{Cu}(T_F-T_{Cu})+m_{Sn}C_{Sn}(T_F-T_{Sn})=0[/tex]
Con el fin de resolver para la temperature final:
[tex]T_F=\frac{m_{Cu}C_{Cu}T_{Cu}+m_{Sn}C_{Sn}T_{Sn}}{m_{Cu}C_{Cu}+m_{Sn}C_{Sn}}[/tex]
Así, reemplazamos las variables conocidas como se muestra a continuación:
[tex]T_F=\frac{150g*0.093cal/g\ºC*1100\°C+35g*0.060cal/g\ºC*560\°C}{150g*0.093cal/g\ºC+35g*0.060cal/g\ºC}\\\\T_F=1029\ºC[/tex]
¡Saludos!
HELP ME PLEASE!!!!!!
I WANT IT AS PARAGRAPHHHHH NOT POINT AND ANSWER THIS TWO QUESTIONS AS 1 PARAGRAPH
One of the lab safety rules being violated is that Jodi doesn't have her hair tied up. She should have her hair tied up. Having her long hair not tied up or away from her face is a safety hazard. Jodi is also not wearing glasses, which is essential when working with chemicals. One of the Bunsen Burners aren't being used but it's on, which is a fire hazard.
Answer:
Jodi should wear her hair up to avoid a mishap, such as lighting her hair on fire. Then, instead of using a fire extinguisher on Jodi, Kimberly should use a fire blanket to prevent additional damage. Mac is preoccupied with a second flame and maybe Jodi without her safety goggles?
I mix together 50.0 mL of 0.100 M NaIO3, 50.00 mL of 0.100 M NaOH, and 10.0 mL of 0.100 M HIO3. What is the pH of the mixture
Answer:
pH = 12.66
Explanation:
The HIO3 reacts with NaOH as follows:
HIO3 + NaOH → H2O + NaIO3
The moles of HIO3 and NaOH added are:
Moles HIO3:
0.0100L * (0.100mol / L) = 0.00100 moles HIO3
Moles NaOH:
0.05000L * (0.100mol / L) = 0.00500 moles NaOH
As moles NaOH > Moles HIO3, the moles of NaOH that remain are:
0.00500mol - 0.00100mol = 0.00400 moles NaOH.
After the reaction you will have only NaOH and NaIO3. As NaIO3 is a salt, the pH of the solution is determined by only NaOH. Its concentration is:
Moles NaOH: 0.00500 moles NaOH
Volume: 50.0mL + 50.0mL + 10.0mL = 110.0mL = 0.110L
Molarity: 0.0455M NaOH = [OH-]
pOH = -log [OH-] = 1.34
pH = 14 - pOH
pH = 12.66pH is the measure of the hydrogen or the hydronium ion in an aqueous solution. The pH of the mixture containing sodium hydroxide is 12.66.
What is pH?pH is the potential of the hydrogen and is given as a negative log of the hydrogen concentration in the aqueous solution.
The balanced chemical reaction can be shown as:
[tex]\rm HIO_{3} + NaOH \rightarrow H_{2}O + NaIO_{3}[/tex]
Moles of iodic acid are calculated as:
[tex]\begin{aligned} \rm moles &= \rm molarity \times volume\\\\&= 0.100 \;\rm M \times 0.0100 \;\rm L \\\\&= 0.00100\;\rm moles\end{aligned}[/tex]
Moles of sodium hydroxide are calculated as:
[tex]\begin{aligned} \rm moles &= \rm molarity \times volume\\\\&= 0.100 \;\rm M \times 0.05000 \;\rm L \\\\&= 0.00500\;\rm moles\end{aligned}[/tex]
The remaining moles of sodium hydroxide are 0.00500mol - 0.00100mol = 0.00400 moles.
The pH of the mixture will be determined by sodium hydroxide, as sodium iodate is a salt.
The molar concentration of sodium hydroxide is calculated as:
[tex]\begin{aligned} \rm M &= \rm \dfrac{moles}{volume}\\\\&= \dfrac{0.00500}{0.110}\\\\&= 0.0455 \;\rm M\end{aligned}[/tex]
pH is calculated as:
[tex]\begin{aligned} \rm pOH &= \rm -log[OH^{-}] = 1.34\\\\\rm pH &= \rm 14 - pOH\\\\\rm pH &= 12.66\end{aligned}[/tex]
Therefore, 12.66 is the pH of the mixture.
Learn more about pH here:
https://brainly.com/question/13539106
Suppose you perform a titration of an unknown weak acid solution. You start with 4.00 mL of the weak acid and find that it takes 14.2 mL of 0.0500 M NaOH to reach the equivalence point. What is the concentration of the unknown weak acid solution
Answer:
0.1775 M
Explanation:
The reaction that takes place is:
HA + NaOH → NaA + H₂OWhere HA is the unknown weak acid.
At the equivalence point all HA moles are converted by NaOH. First we calculate how many NaOH moles reacted, using the given concentration and volume:
0.0500 M NaOH * 14.2 mL = 0.71 mmol NaOHThat means that in 4.00 mL of the weak acid solution, there were 0.71 weak acid mmoles. With that in mind we can now calculate the concentration:
0.71 mmol HA / 4.00 mL = 0.1775 M1. Calculate the number of moles of aluminum, sulfur, and oxygen atoms in 8.00 moles of aluminum sulfate, Al2(SO4)3. 2. Calculate the number of moles of magnesium, chlorine, and oxygen atoms in 6.10 moles of magnesium perchlorate, (Mg(CIO4)2.3. A sample of propane, C3H8, contains 13.8 moles of carbon atoms. How many total moles of atoms does the sample contain?4. A rare gold coin (24 karat, or 100% gold) has a mass of 25.54 g. How many atoms of gold are present in this coin?
Answer:
1) 16.0 moles Al
24.0 moles S
96.0 moles O
2)In 6.10 moles magnesium perchlorate, (Mg(CIO4)2 we have:
6.10 moles Mg
12.2 moles Cl
48.8 moles O
3)4.6 moles of propane (total) contains 13.8 moles of carbon and 36.8 moles of hydrogen atoms
4)The gold coin contains 7.8 *10^22 atoms
Explanation:
Step 1: Data given
Number of moles of aluminum sulfate, Al2(SO4)3 = 8.00 moles
Step 2: Calculate the number of moles
In 1 mol of aluminum sulfate, Al2(SO4)3 we have:
2 moles of Al
3 moles of S
12 moles of O
This means that in 8.00 moles of aluminum sulfate, Al2(SO4)3 we have:
2*8.00 = 16.0 moles Al
3*8.00 = 24.0 moles S
12*8 = 96.0 moles O
2. Calculate the number of moles of magnesium, chlorine, and oxygen atoms in 6.10 moles of magnesium perchlorate, (Mg(CIO4)2
1 mol of magnesium perchlorate, (Mg(CIO4)2 has:
1 Mol of Mg
2 moles of Cl
8 moles of O
In 6.10 moles magnesium perchlorate, (Mg(CIO4)2 we have:
1 * 6.10 moles = 6.10 moles Mg
2*6.10 = 12.2 moles Cl
8*6.10 = 48.8 moles O
3. A sample of propane, C3H8, contains 13.8 moles of carbon atoms. How many total moles of atoms does the sample contain?
In 1 mol of propane, C3H8 we have:
3 moles of C and 8 moles of H
This means if we have 13.8 moles of carbon, we have 13.8/3 = 4.6 moles of propane, C3H8 and 4.6 *8 = 36.8 moles of H
So 4.6 moles of propane contains 13.8 moles of carbon and 36.8 moles of hydrogen atoms
4. A rare gold coin (24 karat, or 100% gold) has a mass of 25.54 g. How many atoms of gold are present in this coin?
Calculate moles of gold:
Moles = mass of gold / molar mass gold
Moles = 25.54 grams / 196.97 g/mol
Moles = 0.1297 moles
Calculate atoms:
Number of atoms = moles * number of Avogadro
0.1297 * 6.022 *10^23 = 7.8 *10^22 atoms
The gold coin contains 7.8 *10^22 atoms
Senario: 2 years ago, a fruit was smuggled into California on a plane from an exotic, far away land. The homeowner saw that the fruit had maggots and tossed it into the backyard, hoping the seed would grow. The larvae hatched out and moved throughout the area. This fictitious insect will destroy fruit and has the possibility of spreading disease killing the trees. The insect consumes plants in the Prunus species of stone fruits? Look up the plant genus Prunus.
Discussion: The insect has spread over a large area of Southern California, discovered at UC Riverside. What steps would you do to control or eradicate the destructive exotic insect?
PLZ HELP THX WITH COLLEGE LEVEL EXPERICENCE
Answer:
The best existing methods of control—artemisinin-based drug treatment and insect control with chemical sprays and treated bednets—can reduce the burden of disease substantially, and can even eliminate the disease in some regions,
hope this will help you more
You have been sent a sample of aspirin to analyse for impurities. Describe how you could
determine if the sample is pure aspirin or not using your knowledge of chemistry.
Answer:
The aspirin could be determined if pure or not by testing it with FeCI3 (aq)
The sample of aspirin can be tested for it's purity by treating it with compound of ferric chloride.
What is a compound?Compound is defined as a chemical substance made up of identical molecules containing atoms from more than one type of chemical element.
Molecule consisting atoms of only one element is not called compound.It is transformed into new substances during chemical reactions. There are four major types of compounds depending on chemical bonding present in them.They are:
1)Molecular compounds where in atoms are joined by covalent bonds.
2) ionic compounds where atoms are joined by ionic bond.
3)Inter-metallic compounds where atoms are held by metallic bonds
4) co-ordination complexes where atoms are held by co-ordinate bonds.
They have a unique chemical structure held together by chemical bonds Compounds have different properties as those of elements because when a compound is formed the properties of the substance are totally altered.
Learn more about compounds,here:
https://brainly.com/question/13516179
#SPJ6
A buffer is prepared containing 0.75 M NH3 and 0.20 M NH4 . Calculate the pH of the buffer using the Kb for NH3. g
Answer:
pH=8.676
Explanation:
Given:
0.75 M [tex]NH_{3}[/tex]
0.20 M [tex]NH_{4}[/tex]
The objective is to calculate the pH of the buffer using the kb for [tex]NH_3[/tex]
Formula used:
[tex]pOH=pka+log\frac{[salt]}{[base]}\\[/tex]
pH=14-pOH
Solution:
On substituting salt=0.75 and base=0.20 in the formula
[tex]pOH=-log(1.77*10^{-5})+log\frac{0.75}{0.20}\\ =4.75+0.5740\\ =5.324[/tex]
pH=14-pOH
On substituting the pOH value in the above expression,
pH=14-5.324
Therefore,
pH=8.676
What is the phase of water at 0.25 atm and 0°C?
Water
(liquid)
Pressure (atm)
0.5-
0.25
Ice
(solid)
Water vapor
(gas)
0
000
Temperature (°C)
O A. Gas
O B. Solid and gas
O C. Solid and liquid
D. Solid
Water is in the solid phase at 0.25 atm and 0°C.
In what phase is water at 25?A pressure of 50 kPa and a temperature of 50 °C correspond to the “water” region—here, water exists only as a liquid. At 25 kPa and 200 °C, water exists only in the gaseous state.
What phase is water in at 0 C?Under standard atmospheric conditions, water exists as a liquid. But if we lower the temperature below 0 degrees Celsius, or 32 degrees Fahrenheit, water changes its phase into a solid called ice.
Learn more about the solid phase here https://brainly.com/question/13396621
#SPJ2
When we react a weak acid with a strong base of equal amounts and concentration, the component of the reaction that will have the greatest effect on the pH of the solution is: Select the correct answer below:_________
a. the reactant acid
b. the reactant base
c. the conjugate acid of the strong base
d. the conjugate base of the weak acid
Answer:
d. the conjugate base of the weak acid
Explanation:
The strong base (BOH) is completely dissociated in water:
BOH → B⁺ + OH⁻
The resulting conjugate acid (OH⁻) is a weak acid, so it remains in solution as OH⁻ ions.
By other hand, the weak acid (HA) is only slightly dissociated in water:
HA ⇄ H⁺ + A⁻
The resulting conjugate base (A⁻) is a weak base. Thus, it reacts with H⁺ ions from water to form HA, increasing the concentration of OH⁻ ions in the solution.
Therefore, the resulting solution will have a pH > 7 (basic).
Excluding any secondary chemical reactions,
which would be more effective as an antifreeze; a
solution containing
Select one:
25m CH3OH
the combination of 25m CH3OH and 25m
KCI.
O 25m KCI.
O
none of these
Answer:
Excluding any secondary chemical reactions,
which would be more effective as an antifreeze; a
solution containing
Select one:
25m CH3OH
the combination of 25m CH3OH and 25m
KCI.
25m KCI.
Explanation:
Antifreeze is the one that reduces the freezing point of a solvent further and will not allow the solvent to freeze.
Among the given options, the correct option is:
25 m CH3OH and 25m KCl.
Since, KOH is a strong electrolyte and dissociates into two ions.
So, the freezing point of solvent decreases further.
Which observation provided Albert Einstein the clue that he needed to explain the photoelectric effect?
Answer:
Einstein realized that the energy in electrons was caused by the frequency of light and not the intensity of light. This made him realize that he needed to explain the photoelectric effect.
Explanation:
Einstein realized that the photoelectric effect was a system that should be studied and explained in more depth, when he saw how the energy of electrons behaved in the presence of light. He saw that this energy depends entirely on the frequency of light and not on the intensity of light. From this observation, he realized that the photoelectric effect was essential for the production of an electric energy system, through light energy, such as solar energy.
It is important to note that the photoelectric effect refers to the ejection of electrons on a light surface that comes into contact with a light source.