An electron-positron pair is produced by a 2.50 MeV photon. What is the kinetic energy of the positron if the kinetic energy of the electron is 0.739
MeV?
Use the following Joules-to-electron-Volts conversion 1eV = 1.602 × 10-19 J.
The rest mass of an electron is 9.11 Å~10−31 kg

We can solve this problem includes continuity of fluid flow and the Bernoulli's equation. The speed of water in the nozzle is approximately 5.2 m/s. The pressure in the nozzle is approximately 0.8 atm or 80.9 kPa. The pressure in the nozzle is approximately 0.8 atm or 80.9 kPa.

a)

Using the principle of continuity of fluid flow, the product of the cross-sectional area of the hose and the speed of water in the hose is equal to the product of the cross-sectional area of the nozzle and the speed of water in the nozzle.

Mathematically, we can write:

A₁V₁ = A₂V₂

where A₁ and V₁ are the cross-sectional area and speed of water in the hose, respectively, and A₂ and V₂ are the cross-sectional area and speed of water in the nozzle, respectively.

Substituting the given values, we get:

([tex]\frac{\pi }{4}[/tex]) ₓ (0.016 m)²ₓ (1.3 m/s) = ([tex]\frac{\pi }{4}[/tex])ₓ (0.0064 m)²V₂

Solving for V₂, we get:

V₂ = ([tex]\frac{0.016^{2} }{0.0064^{2} }[/tex]) × (1.3 m/s) = 5.2 m/s

Therefore, the speed of water in the nozzle is approximately 5.2 m/s.

b)

Using Bernoulli's equation, the sum of the pressure, kinetic energy, and potential energy per unit volume of a fluid at any point in the fluid is constant. Assuming that the height of the hose and the nozzle is the same, we can neglect the potential energy terms and write:

P₁ +  [tex]\frac{1}{2}[/tex]ρV₁² = P₂ +  [tex]\frac{1}{2}[/tex]ρV₂²

where P₁ and V₁ are the pressure and speed of water in the hose, respectively, ρ is the density of water, and P₂ and V₂ are the pressure and speed of water in the nozzle, respectively.

Substituting the given values, we get:

(1.5 atm) × (101.3 kPa/atm) +  [tex]\frac{1}{2}[/tex](1000 kg/m³) × (1.3 m/s)² = P₂ +  [tex]\frac{1}{2}[/tex] ₓ (1000 kg/m³) × (5.2 m/s)²

Solving for P₂, we get:

P₂  = (1.5 atm) × (101.3 kPa/atm) + [tex]\frac{1}{2}[/tex] ₓ (1000 kg/m³) × (1.3 m/s)² - [tex]\frac{1}{2}[/tex] × (1000 kg/m³) × (5.2 m/s)² =  0.8 atm or 80.9 kPa

P₂ = 151.95 + 650 - 2600

Therefore, the pressure in the nozzle is approximately 0.8 atm or 80.9 kPa.

To know more about continuity of fluid

https://brainly.com/question/30267328

#SPJ4

The astrometric method of finding planets works by observing the precise movement of a star caused by the gravitational forces of a planet.

This method involves measuring the position of a star over time and detecting any small shifts or wobbles in its movement. These shifts are caused by the gravitational pull of an orbiting planet, which causes the star to move slightly back and forth in space. By carefully measuring the position of the star relative to the background stars over a period of time, astronomers can detect these subtle movements and infer the presence of an orbiting planet. This method is particularly effective for detecting massive planets that orbit far from their host stars.

Learn more about gravitational here :

https://brainly.com/question/3009841

#SPJ11

The periglacial process that causes vertical movement of soil and rocks is frost heaving. Frost heaving occurs when water in the soil freezes and expands, exerting pressure on the surrounding materials.

This expansion can uplift or raise the soil and rocks, leading to vertical movement. The repeated cycles of freezing and thawing result in the gradual displacement of particles, causing the surface to become uneven. Frost heaving is particularly common in cold regions where the ground experiences freezing temperatures and adequate moisture is present. It plays a significant role in shaping the landscape and influencing the formation of features like frost mounds and frost boils.

learn more about vertical here:

https://brainly.com/question/30116773

#SPJ11

Yes, the magnetic flux through the loop is changing.

The metal loop is pulled through a uniform magnetic field, the magnetic field lines passing through the loop are changing. This causes a change in the magnetic flux through the loop, which is defined as the product of the magnetic field strength and the area of the loop perpendicular to the field lines. As the loop moves, the area perpendicular to the magnetic field lines changes, resulting in a change in magnetic flux.

"The metal loop is being pulled through a uniform magnetic field. Is the magnetic flux through the loop changing?"

The magnetic flux through the metal loop is changing when it is being pulled through a uniform magnetic field. Magnetic flux (Φ) is the measure of the magnetic field (B) passing through a given surface area (A) and is given by the equation Φ = B*A*cos(θ), where θ is the angle between the magnetic field and the area vector.

As the loop is pulled through the magnetic field, the orientation and/or the area of the loop exposed to the magnetic field may change, which in turn changes the magnetic flux through the loop.

Learn more about magnetic field here,

https://brainly.com/question/14411049

#SPJ11

The total vapour pressure of a solution is 110mmHg which is calculated using Raoult's law. The mole fraction of substance A is given as 0.35, and the vapour pressures of pure A and B are given as 87 mmHg and 122 mmHg.

According to Raoult's law, the partial pressure of a component in a solution is proportional to its mole fraction. The mole fraction of substance A is 0.35, which means that it constitutes 35% of the solution. Therefore, the contribution of substance A to the total vapour pressure is 0.35 times its vapour pressure, which is 0.35 * 87 mmHg = 30.45 mmHg.

Similarly, the contribution of substance B can be calculated as 0.65 times its vapour pressure, which is 0.65 * 122 mmHg = 79.3 mmHg.

To find the total vapour pressure, we add the partial pressures of A and B: 30.45 mmHg + 79.3 mmHg = 109.75 mmHg.

Rounding this value to the nearest whole number, we get 110 mmHg. Therefore, the correct answer is option a) 110 mmHg.

Learn more about Raoult's law here:

https://brainly.com/question/28304759

#SPJ11

The boy's mass can be determined by applying the law of conservation of momentum. The mass of the skateboard is given as 2.0 kg, and the jug of water has a mass of 8.0 kg.

The jug is thrown forward with a speed of 3.0 m/s relative to the ground, while the boy and skateboard move in the opposite direction at 0.60 m/s. To find the boy's mass, we can use the equation:

[tex]\[(m_{\text{{boy}}} + m_{\text{{skateboard}}}) \cdot v_{\text{{boy}}} = m_{\text{{jug}}} \cdot v_{\text{{jug}}}\][/tex]

where [tex]\(m_{\text{{boy}}}\)[/tex] is the boy's mass, [tex]\(m_{\text{{skateboard}}}\)[/tex] is the skateboard's mass, [tex]\(v_{\text{{boy}}}\)[/tex] is the boy's velocity, [tex]\(m_{\text{{jug}}}\)[/tex] is the jug's mass, and [tex]\(v_{\text{{jug}}}\)[/tex] is the jug's velocity.

Rearranging the equation to solve for [tex]\(m_{\text{{boy}}}\)[/tex], we have:

[tex]\[m_{\text{{boy}}} = \frac{{m_{\text{{jug}}} \cdot v_{\text{{jug}}}}}{{v_{\text{{boy}}}}} - m_{\text{{skateboard}}}\][/tex]

Substituting the given values, we get:

[tex]\[m_{\text{{boy}}} = \frac{{8.0 \, \text{{kg}} \cdot 3.0 \, \text{{m/s}}}}{{0.60 \, \text{{m/s}}}} - 2.0 \, \text{{kg}}\][/tex]

Simplifying the equation, we find:

[tex]\[m_{\text{{boy}}} = 38 \, \text{{kg}}\][/tex]

Therefore, the boy's mass is 38 kg.

To learn more about momentum refer:

https://brainly.com/question/1042017

#SPJ11

Real-world efficiencies are generally very high, in the 90 percent range. This statement is generally false.

While efficiencies in some industries can reach the high 90s, this is not the case across the board. The efficiency of a system refers to the ratio of useful work done by the system to the energy that is supplied to it. It is usually expressed as a percentage. An efficiency of 100% would mean that all the energy put into the system is used to perform useful work, with no losses. In reality, it is impossible to achieve 100% efficiency because some energy will always be lost to friction, heat, or other inefficiencies.In some industries, such as power generation, the efficiency of the system can be very high, typically around 60-70% for fossil fuel plants and up to 90% for combined cycle gas turbine plants. However, in other industries, such as transportation, efficiencies can be much lower. For example, the efficiency of a gasoline engine is typically only around 20-25%.In conclusion, while some industries can achieve very high efficiencies, it is not accurate to say that real-world efficiencies are generally in the 90 percent range. The efficiency of a system depends on many factors, including the design of the system, the operating conditions, and the nature of the energy source.

learn more about turbine Refer: https://brainly.com/question/31624271

#SPJ11

The bigger fragments in gel electrophoresis are predicted to go the shortest distance from the well. This is due to the fact that gel electrophoresis divides DNA or other biomolecules according to their charge and size.

An electric field is spread over the gel matrix during electrophoresis. DNA molecules that are negatively charged move in the direction of the positive electrode. The gel matrix nevertheless functions as a molecular sieve, restricting the flow of bigger molecules more so than smaller ones.

Larger pieces move slower than smaller fragments because they encounter more resistance as they move through the gel matrix. As a result, they move closer to the positive electrode from the well than smaller fragments do because they can move through the gel's pores more readily.

To know more about gel electrophoresis, here

brainly.com/question/30051368

#SPJ4

The answer is the net heat transfer for the system is -6000 kJ.



We can use the first law of thermodynamics to solve this problem. The first law states that the change in internal energy of a system is equal to the heat added to the system minus the work done by the system. In this case, we can assume that the refrigerator is an isolated system, so there is no work done.

First, we need to convert the energy consumption from kW h to kJ. 1 kW h is equal to 3600 kJ (1 kW = 1000 W, and 1 hour = 3600 seconds), so the energy consumption is 3600 kJ.

Now we can use the first law to find the heat transfer. We know that the internal energy of the system dropped by 5000 kJ, so:

ΔU = Q - W
-5000 kJ = Q - 0
Q = -5000 kJ

The negative sign indicates that heat was lost from the system. We also know that the energy consumption was 3600 kJ, so:

net heat transfer = heat lost - energy consumption
net heat transfer = -5000 kJ - 3600 kJ
net heat transfer = -8600 kJ

However, the question asks for the net heat transfer, which is the heat transfer in one direction minus the heat transfer in the other direction. Since heat only transferred out of the system in this case, the net heat transfer is simply the negative of the heat lost:

net heat transfer = -(-5000 kJ)
net heat transfer = 5000 kJ

But we need the answer in joules, not kilojoules. 1 kJ = 1000 J, so the net heat transfer is:

net heat transfer = 5000 kJ * 1000 J/kJ
net heat transfer = 5,000,000 J

Finally, we need to convert from joules to kilojoules, since the answer is in kW h:

net heat transfer = 5,000,000 J / 1000 J/kJ
net heat transfer = 5000 kJ

Therefore, the net heat transfer for the system is -6000 kJ.

To know more about thermodynamics visit:

brainly.com/question/1368306

#SPJ11

Volcanic eruptions can have significant impacts on the availability of resources by disrupting the sunlight from reaching producers, By decreasing the thickness of soil, By causing more heavy rains to erode topsoil, By causing the surface of the Earth to be warmer than usual.

know more about Volcanic eruptions here:

https://brainly.com/question/20151104

#SPJ8

The correct answer is b. distance that a force acts, as it accurately describes the concept of work. The other options (a, c, and d) are not accurate descriptions of the relationship between impulse and work.

Impulse is defined as the change in momentum of an object and is calculated by multiplying the force applied to an object by the time interval over which the force is applied. It is directly related to the time duration of the force acting on an object. On the other hand, work is defined as the product of the force applied to an object and the distance over which the force is applied. It is a measure of the energy transferred to or from an object by the force.

Based on this understanding, the correct answer is B. distance that a force acts. The incorrect answers and their reasons:

Learn more about impulse: https://brainly.com/question/30395939

#SPJ11

The tension in the string when the rock is totally immersed in a liquid with density 750 kg/m^3 can be found using Archimedes' principle, which states that the buoyant force on an object submerged in a fluid is equal to the weight of the fluid displaced by the object.

The weight of the rock in air is given by W = mg, where m is the mass of the rock and g is the acceleration due to gravity. Using the density formula, we can find the mass of the rock as m = ρV, where ρ is the density of the rock and V is its volume. Since the tension of the rock remains constant, we can write:

Force (Fb) can be calculated using the formula: Fb = V * ρL * g, where V is the volume of the rock, ρL is the density of the liquid, and g is the acceleration due to gravity (approximately 9.81 m/s²).

To know more about tension visit :-

https://brainly.com/question/15543867

#SPJ11

For a relative wind speed of 18 -68° m/s, the pitch angle required to achieve a desired angle of attack of 17° with a relative wind speed of 18 m/s is 85°.

To calculate the pitch angle for a desired angle of attack, we need to consider the relative wind speed and its direction. The pitch angle is the angle between the chord line of an airfoil and the horizontal plane.

Given:

Relative wind speed: 18 m/s

Relative wind direction: -68°

Desired angle of attack: 17°

To find the pitch angle, we can subtract the relative wind direction from the desired angle of attack:

Pitch angle = Desired angle of attack - Relative wind direction

Pitch angle = 17° - (-68°)

Simplifying the expression:

Pitch angle = 17° + 68°

Pitch angle = 85°

For more such information on: speed

https://brainly.com/question/30249508

#SPJ11

The mean free path in the gas is given by the formula: mean free path = (k * T) / (sqrt(2) * pi * d^2 * P), where k is Boltzmann's constant, T is the temperature in Kelvin, d is the diameter of a helium atom.

P is the pressure in atm. The diameter of a helium atom is approximately 2.4 Ångstroms.

The rms speed of the atoms is given by the formula: rms speed = sqrt((3 * k * T) / (m)), where k is Boltzmann's constant, T is the temperature in Kelvin, and m is the mass of a helium atom.

The average energy per atom is given by the formula: average energy per atom = (3/2) * k * T, where k is Boltzmann's constant and T is the temperature in Kelvin.

The mean free path is the average distance an atom travels between collisions. It depends on the temperature, pressure, and size of the atoms.

The rms speed is the square root of the average of the squared speeds of the atoms. It gives an indication of the magnitude of the velocities of the atoms.

The average energy per atom is the average kinetic energy of the atoms in the gas. It depends only on the temperature and is proportional to the absolute temperature.

learn more about atom here:

https://brainly.com/question/1566330

#SPJ11

i.) A water molecule has a dispersion equal to 1.

ii.) The smallest silicon particle consisting of a silicon atom and its nearest neighbors has a dispersion of 4/5.

i.) In a water molecule (H₂O), there are 3 atoms in total, which are 2 hydrogen atoms and 1 oxygen atom. All of these atoms are on the surface of the molecule. Therefore, the dispersion of a water molecule is:

Number of surface atoms / Total number of atoms = 3/3 = 1

ii.) For the smallest silicon particle consisting of a silicon atom and its nearest neighbors, let's assume it forms a tetrahedron with one silicon atom at the center and four silicon atoms as its nearest neighbors. In this case, there are 5 atoms in total, and only the 4 atoms on the vertices are on the surface. The dispersion of this silicon particle is:

Number of surface atoms / Total number of atoms = 4/5

So, the dispersion for the water molecule is 1, and for the smallest silicon particle, it is 4/5.

Learn more about dispersion here: https://brainly.com/question/14263432

#SPJ11

A circuit consists of a 100 ohm resistor and a 150 nf capacitor wired in series and connected to a 6 v battery. The maximum charge the capacitor can store is 900 microcoulombs.

To find the maximum charge stored in the capacitor, we need to use the formula Q=CV, where Q is the charge stored, C is the capacitance and V is the voltage across the capacitor.

Since the capacitor and resistor are wired in series, the voltage across the capacitor is the same as the battery voltage of 6 V. The capacitance is given as 150 nf (nano farads), which is equivalent to 0.15 microfarads (μF). Plugging in these values, we get Q=0.15μF x 6V = 0.9μC (microcoulombs). Therefore, the maximum charge the capacitor can store is 900 microcoulombs.

Learn more about capacitor here:

https://brainly.com/question/17176550

#SPJ11

The total moment of inertia of the four blades of the typical helicopter is approximately 269.5 kg · m^2.To calculate the total moment of inertia, we need to use the formula: kinetic energy = (1/2) * moment of inertia * (angular velocity)^2.

We are given the kinetic energy and the angular velocity, so we can rearrange the formula to solve for the moment of inertia.

First, we need to convert the rotational speed from revolutions per minute (rpm) to radians per second (rad/s). We know that 1 revolution is equal to 2π radians, so:
360 rpm = (360/60) rev/s = 6 rev/s = 6 * 2π rad/s = 12π rad/s

Now, we can substitute the values into the formula:
4.65 * 10^5 J = (1/2) * moment of inertia * (12π)^

Simplifying, we get:
moment of inertia = (2 * 4.65 * 10^5 J) / (144π^2) = 269.5 kg · m^2 (rounded to one decimal place)

Therefore, the total moment of inertia of the four blades of the typical helicopter is approximately 269.5 kg · m^2.

For more question on inertia

https://brainly.com/question/20734058

#SPJ11

In this scenario, a typical helicopter with four blades rotates at 360 rpm and has a kinetic energy of 4.65 105 j.The total moment of inertia of the helicopter blades is 0.0345 kg · m2.
 

Moment of inertia refers to the resistance of an object to changes in its rotational motion. It is affected by both the mass and the distribution of that mass. In the case of the helicopter blades, we can assume that they have a uniform distribution of mass since they are designed to rotate evenly.
To calculate the moment of inertia, we can use the formula I = KE/(w^2) where I is the moment of inertia, KE is the kinetic energy, and w is the angular velocity. In this case, we are given the KE and the w (360 rpm = 37.7 rad/s). Plugging these values into the formula, we get I = 4.65 105 j / (37.7 rad/s)^2 = 0.0345 kg · m2.

Therefore, the total moment of inertia of the helicopter blades is 0.0345 kg · m2.

To learn more about Inertia click here:brainly.com/question/3268780

#SPJ11

All these energy generation methods share the common feature of using mechanical energy to rotate a turbine or generator, which then converts this mechanical energy into electrical energy. The electricity produced is then transferred through wires for consumption.

In HydroElectric power generation, water is used to drive a turbine, which in turn rotates a generator to create electricity. Similarly, a Bicycle Dynamo utilizes the rider's pedaling motion to rotate a small generator, producing electrical energy. Wind power generation relies on wind to turn the blades of a wind turbine, which then spins a generator to create electricity. Finally, Magnetic power generation uses the force of magnets to spin a generator, converting mechanical energy into electricity.

Despite the different sources of mechanical energy, all these methods ultimately rely on the principle of electromagnetic induction. When a conductor (usually a coil of wire) rotates in a magnetic field, a current is induced in the wire. This process of electromagnetic induction is the key similarity between these diverse methods of generating electricity. The generated electricity then flows through wires, powering electrical devices and contributing to the electrical grid.

To know more about electromagnetic induction, click here;

https://brainly.com/question/13369951

#SPJ11

(a) In order to find the width of a single slit that produces its first minimum at 60.0º for 600-nm light, you can proceed as under d sinθ = mλ, where d is the width of the slit, θ is the angle of the first minimum (60.0º), m is the order of the minimum (1), and λ is the wavelength of the light (600 nm).

d = mλ / sinθ.
d = (1)(600 nm) / sin(60.0º) = 692 nm.
(b) To find the wavelength of light that has its first minimum at 62.0º, we can use the same formula: d sinθ = mλ.

λ = d sinθ / m.

λ = (692 nm) sin(62.0º) / (1) = 558 nm.

Read more about Single slit.

https://brainly.com/question/30890401

#SPJ11

The ratio of strength to mass scales like 1/L for a cubical critter of length L. This means that as the length of the critter increases, the ratio of its strength to mass decreases.

This scaling can be used to explain why the leg bones of large ungulates (e.g. water buffalos) have larger ratios than the leg bones of smaller ungulates (e.g. gazelles). Since water buffalos are larger in size than gazelles, their leg bones need to be stronger to support their weight. Therefore, their leg bones have a larger ratio of strength to mass compared to the leg bones of smaller ungulates.

Thus, the ratio of strength to mass scales like 1/L for a cubical critter of length L, and this scaling can be used to explain why the leg bones of large ungulates have larger ratios than the leg bones of smaller ungulates.

To know more about cubical critter, click here

https://brainly.com/question/17102388

#SPJ11

The work done by the force is approximately -12.1 J.

The work done by a constant force is given by the equation W = F . d, where F is the force vector, d is the displacement vector, and "." represents the dot product. The displacement of the particle is given by the vector r, so we can calculate the work done as follows:

W = F . d = (3.39i + 4.72j) N . (1.85i - 2.51j) m

= (3.39 x 1.85 + 4.72 x (-2.51)) J

= -12.1 J (to two decimal places)

The speed of the particle at position r can be calculated using the conservation of energy principle. Since no external work is done on the system (i.e., the net work is zero), the initial kinetic energy of the particle is equal to its final kinetic energy plus its change in potential energy. We can solve for the final speed as follows:

Initial kinetic energy = 1/2 mv^2 = 1/2 x 3.51 kg x (4.51 m/s)^2 = 35.8 J

Final kinetic energy = 1/2 mv^2 (where v is the final speed)

Change in potential energy = -W = 12.1 J (from above)

Therefore, 35.8 J = 1/2 x 3.51 kg x v^2 + 12.1 J, which gives v = 5.17 m/s (to two decimal places).

The change in potential energy of the system is equal to the negative of the work done by the force, so it is approximately 12.1 J (as calculated above).

To know more about kinetic energy, click here:

https://brainly.com/question/26472013

#SPJ11

(a) 64.7° is the acceptance angle (in degrees) for the oil immersion objective

(b) 30° is the acceptance angle (in degrees) for the air immersion objective.

Part (a): The acceptance angle for the oil immersion objective can be calculated using the formula α1 = sin⁻¹(NA1/n), where NA1 is the numerical aperture of the objective and n is the refractive index of the medium between the specimen and the objective. Here, NA1 = 1.40 and n = 1.51 (refractive index of oil). Substituting these values, we get α1 = sin⁻¹(1.40/1.51) = 64.7°.
Part (b): The acceptance angle for the air immersion objective can be calculated using the formula α2 = sin⁻¹(NA2/n), where NA2 is the numerical aperture of the objective and n is the refractive index of the medium between the specimen and the objective. Here, NA2 = 0.5 and n = 1 (refractive index of air). Substituting these values, we get α2 = sin⁻¹(0.5/1) = 30°.
In summary, the acceptance angle for the oil immersion objective is 64.7°, while the acceptance angle for the air immersion objective is 30°. This difference in acceptance angle is due to the fact that oil has a higher refractive index than air, which allows for greater light refraction and therefore a larger acceptance angle.

To know more about immersion visit:

brainly.com/question/29306517

#SPJ11

It is not possible to conclusively determine whether object A or object B is a conductor or insulator. A charged object can be either a conductor or an insulator, as both can hold a charge. Similarly, an uncharged object could also be a conductor or insulator, as its current state does not provide enough information about its material properties.

To determine whether object A or object B is a conductor or an insulator, additional information about the materials they are made of is needed. If object A is made of a metal, it is likely a conductor, while if it is made of a non-metal, it may be an insulator. Similarly, if object B is made of a metal, it is likely a conductor, while if it is made of a non-metal, it may be an insulator.

In summary, the fact that object A is charged and object B is uncharged does not provide enough information to determine whether either object is a conductor or an insulator. Additional information about the materials they are made of is needed to make this determination.

To know more about insulator visit:-

https://brainly.com/question/26588963

#SPJ11

The initial element X is not provided, we cannot determine the specific final nucleus (atomic mass and atomic number) after the sequence of decays (beta-plus, gamma, and alpha decay).

In nuclear decay processes, the initial element undergoes transformations resulting in the formation of a final nucleus with different atomic mass and atomic number. The sequence mentioned involves beta-plus decay, followed by gamma decay, and finally alpha decay. However, without knowing the initial element, it is not possible to determine the specific final nucleus.

The outcome of each decay depends on the properties of the starting element. Beta-plus decay involves the emission of a positron and a neutrino, gamma decay involves the emission of a gamma ray photon, and alpha decay involves the emission of an alpha particle. The combination of these decays alters the atomic mass and atomic number of the nucleus, leading to the formation of a new element. To provide a precise answer, the identity of the initial element is required.

Learn more about Nuclear decays

brainly.com/question/21114779

#SPJ11

Answer:The value of the capacitor in a low-pass RC filter with a crossover frequency of 1100 Hz and a 130 ohm resistor can be calculated using the formula:

C = 1/(2π × f × R)

Where C is the capacitance in Farads, f is the crossover frequency in Hertz, and R is the resistance in ohms.

Substituting the given values in the formula, we get:

C = 1/(2π × 1100 × 130) = 1.037 × 10^(-6) F

Converting the answer to microfarads, we get:

C = 1.037 μF

Therefore, the value of the capacitor in the low-pass RC filter is 1.037 microfarads.

Learn more about RC filters and their applications in electronics.

https://brainly.com/question/31327507?referrer=searchResults

#SPJ11

Answer:

Angular acceleration: approximately [tex]1.225\; {\rm s^{-2}}[/tex].

The wheel stopped after approximately [tex]11.4\; {\rm s}[/tex].

(Assuming that the angular acceleration of the wheel is constant.)

Explanation:

Rearrange the following equation to find the angular acceleration of this wheel:

[tex]2\, a\, x = v^{2} - u^{2}[/tex],

Where:

In this question, it is given that [tex]x = 80[/tex] and [tex]u = 14\; {\rm s^{-1}}[/tex]. Additionally, [tex]v = 0\; {\rm s^{-1}}[/tex] since the wheel has stopped rotating. Rearrange the equation to find [tex]a[/tex]:

[tex]\begin{aligned}a &= \frac{v^{2} - u^{2}}{2\, x} \\ &= \frac{(0)^{2} - (14)^{2}}{2\, (80)}\; {\rm s^{-2}} \\ &= 1.225\; {\rm s^{-2}}\end{aligned}[/tex].

Divide the change in angular velocity [tex](v - u)[/tex] by angular acceleration to find the time required:

[tex]\begin{aligned} t &= \frac{v- u}{a} \\ &= \frac{0 - 14}{(-1.225)}\; {\rm s} \\ &\approx 11.4\; {\rm s}\end{aligned}[/tex].

The image is located at 21.8 cm from the lens and its height is 0.29 cm.

To find the position of the image, we can use the thin lens equation:

1/f = 1/d₀ + 1/dᵢ

where, f is the focal length of the lens,

           d₀ is the object distance, and,

           dᵢ is the image distance.

We can solve for dᵢ, as:

1/dᵢ = 1/f - 1/d₀

dᵢ = 1 / (1/f - 1/d₀)

Substituting the values, d₀ = -75 cm and f = 30 cm, we get:

dᵢ = 1 / (1/30 cm - 1/-75 cm) = 21.8 cm

So the image is located 21.8 cm from the lens.

To calculate the height, we can use the magnification equation:

m = -dᵢ / d₀

where m is the magnification.

Putting the values, we get:

m = -21.8 cm / -75 cm = 0.29

This tells us that the image is smaller than the object, since the magnification is less than 1.

Now,

m = hᵢ / h₀

where h₀ is the height of the object and hᵢ is the height of the image. Putting in the values, we get:

0.29 = hᵢ / 1.0 cm

hᵢ = 0.29 cm

Learn more about magnification here

brainly.com/question/20368024

#SPJ4

Given that water is 2000 m deep, all three waves will be travelling at same speed, as the depth of water is significant enough to make the speed of the wave independent of the wavelength. Therefore, option C, "All move at the same speed," is the correct answer.

The speed of a wave in a medium is dependent on the properties of the medium, such as its density and elasticity. In general, waves with longer wavelengths will travel faster in a given medium than those with shorter wavelengths.

In the case of water waves, the speed is also dependent on the depth of the water. As the depth of the water increases, the speed of the wave increases as well. This is because the deeper water has a higher density and greater elasticity, which allows for faster propagation of the wave.

It is important to note that the speed of the waves would not be the same if the depth of the water was not significant enough to make the speed independent of the wavelength. In shallower water, the longer wavelength waves would travel faster than the shorter wavelength waves. option C, is the correct answer.

Know more about wavelength here:

https://brainly.com/question/4112024

#SPJ11

The centroid y of the homogeneous solid formed by revolving the shaded area about the y-axis can be located using principles of calculus and geometry.

To locate the centroid y, we need to find the geometric center of the solid formed by rotating the shaded area around the y-axis. The centroid represents the balance point of the solid and is calculated using integral calculus.

To determine the centroid, we can divide the solid into infinitesimally thin slices along the y-axis. Each slice has a certain thickness and an associated differential volume element.

By integrating the product of the differential volume element and its corresponding y-coordinate over the entire solid, we can find the total moment about the y-axis.

Next, we divide this moment by the total volume of the solid to obtain the y-coordinate of the centroid. The centroid y is given by the equation [tex]y = (1/V) * ∫(y*dV),[/tex] where V represents the volume of the solid and the integral is taken over the entire solid.

By evaluating this integral and performing the necessary calculations, we can determine the centroid y of the solid formed by revolving the shaded area about the y-axis.

Learn more about rotational symmetry

brainly.com/question/29044130

#SPJ11

The angular acceleration of the ultracentrifuge is 921.7 radians per second square.

The ultracentrifuge accelerates from rest to 9.85×10^5 rpm in 1.87 min. We need to convert the rpm to radians per second in order to find the angular acceleration.

1 rpm = (2π/60) radians per second

So, 9.85×10^5 rpm = (2π/60) * 9.85×10^5 radians per second = 103,257 radians per second

The time taken is 1.87 min, which is 112.2 seconds.

Using the formula for angular acceleration:

angular acceleration = (final angular velocity - initial angular velocity) / time

The initial angular velocity is 0 (starting from rest).

angular acceleration = (103257 radians per second - 0 radians per second) / 112.2 seconds

angular acceleration = 921.7 radians per second squared

To know more about the angular acceleration, click here,

https://brainly.com/question/29428475

#SPJ11