A hydrate of sodium carbonate, Na[tex]_2[/tex]CO[tex]_3[/tex] has a mass of 4.31 g before heating. After heating, the mass of the anhydrous compound is found to be 3.22 g. Therefore, The mass of water in the original sample is 1.09g.
What is sodium carbonate?Sodium carbonate is an inorganic compound with the formula Na[tex]_2[/tex]CO[tex]_3[/tex], where x may range from 0 and 10. All forms are water-soluble, white, unscented salts that generate alkaline water solutions. It was historically made first from ash of plants grown in sodium-rich soil.
Before heating, a hydrates of sodium carbonate, Na[tex]_2[/tex]CO[tex]_3[/tex], does have a mass of 4.31 g. The weight of the anhydrous salt after heating is determined to be 3.22 g. The original sample contains 4.31-3.22 =1.09g of water.
Therefore, the mass of water in the original sample is 1.09g.
To learn more about sodium carbonate, here:
https://brainly.com/question/28236059
#SPJ9
Use the information in the table below to answer the question that follows:
If an electromagnetic wave traveled through each of the media (materials) above, which medium (material) is most likely a solid?
Material 1
Material 2
Material 3
Material 4
The medium (material) with the fastest electromagnetic wave speed, material 1, with a speed of 3.0 108 m/s, would be the one that is most likely a solid.
What types of waves can penetrate a solid?A P wave. The P wave, or main wave, is the initial type of body wave. It is the type of seismic wave that travels the fastest and arrives first at a seismic station.
A solid item can light waves flow through it?Some photons are absorbed by the atoms in some materials, including metal, preventing light from passing through. These substances are translucent. In different materials, like glass, the Since atoms are unable to absorb photons, light travels through them. These substances are translucent.
To know more about electromagnetic visit:-
https://brainly.com/question/12369229
#SPJ1
For the Kuhn segment of many polymers, (b/d) ≈ 2–3. Polystyrene is known to have a Kuhn length b = 0.7 nm and a θ-temperature of 34.5 ◦C in cyclohexane. (i) At a temperature of T = 80 ◦C, does cyclohexane act as a good solvent or an athermal solvent? Justify your answer mathematically. (ii) What is the value of T above which the system is athermal? Given the boiling point of cyclohexane, is this accessible under standard conditions (P = 1 atm)?
5. For the Kuhn segment of many polymers, (b/d)≈ 2-3. Polystyrene is known to have a Kuhn length b=0.7 nm and a 6-temperature of 34.5 °C in cyclohexane.
(i) At a temperature of T = 80 °C, does cyclohexane act as a good solvent or an athermal solvent? Justify your answer mathematically.
(ii) What is the value of T above which the system is athermal? Given the boiling point of cyclohexane, is this accessible under standard conditions (P=1 atm)?
(i) Cyclohexane acts as a good solvent at a temperature of T = 80 °C because it is above the θ-temperature of 34.5 °C.(ii) The value of T above which the system is athermal is the θ-temperature, which is 34.5 °C for polystyrene in cyclohexane.
i) In a good solvent, the polymer coils expand and the polymer-solvent interactions are stronger than the polymer-polymer interactions.
Therefore, Cyclohexane acts as a good solvent at a temperature of T = 80 °C because it is above the θ-temperature of 34.5 °C.
This can be mathematically justified by the Flory-Huggins equation: χ = (V1/RT)(ΔH - TΔS)
where χ is the Flory-Huggins interaction parameter, V1 is the molar volume of the solvent, R is the gas constant, T is the temperature, ΔH is the enthalpy of mixing, and ΔS is the entropy of mixing.
At temperatures above the θ-temperature, χ is negative, indicating that the polymer-solvent interactions are stronger than the polymer-polymer interactions and the solvent is a good solvent.
(ii) The value of T above which the system is athermal is the θ-temperature, which is 34.5 °C for polystyrene in cyclohexane.
Above this temperature, the polymer-solvent interactions are stronger than the polymer-polymer interactions and the solvent is a good solvent.
The boiling point of cyclohexane is 80.7 °C, so this temperature is accessible under standard conditions (P=1 atm).
To know more about solvents, refer here:
https://brainly.com/question/30452436#
#SPJ11
consider the reaction below involving the combustion of hydrogen gas: 2h2(g) o2(g) 2h2o(g) what will be the volume of water vapor produced when 8 grams of h2 reacts at stp?
Quick chemical reaction between a material and oxygen that results in the generation of heat and light.
What is combustion?
Combustion is a chemical process that often involves the presence of oxygen and produces heat and light in the form of flames. Because of the nature of the chemical reaction and the fact that more energy is produced than can be released into the surrounding medium, the rate or speed at which the reactants combine is high. As a result, the temperature of the reactants is increased, accelerating the process even more.
A lit match is a common illustration of a combustion process. A flame is produced when a match is struck because friction warms the head to a temperature where the chemicals react and produce more heat than can be released into the atmosphere.
To know more about combustion, check the link below:
https://brainly.com/question/10458605
#SPJ4
Find the mode of the following number of boxes of graduated cylinders that were ordered for each lab of a college science department.
5,13,13,3,5,9,13,5,5,6
The mode is the value that appears most frequently in the data set. In this case, the value of 5 appears most frequently, occurring 4 times. Therefore, the mode of the number of boxes of graduated cylinders that were ordered for each lab of a college science department is 5.
The mode is a statistical measure that represents the value that appears most frequently in a data set. It is a useful measure of central tendency, especially when dealing with nominal or categorical data. The mode can be easily found by identifying the value with the highest frequency in the data set. In some cases, a data set may have multiple modes if there are two or more values with the same highest frequency.
learn more about mode here:
https://brainly.com/question/28566521
#SPJ4
Which statement about cells and sugar is true?
Answer:
There are many statements that can be made about cells and sugar, but here are three possible options with one true statement:
All cells require sugar to function properly.
Sugar is harmful to cells and should be avoided.
Cells can store excess sugar as fat.
Explanation:
The true statement is: "All cells require sugar to function properly."
Consider a gas sample inside of a container. Which of the following changes will decrease the pressure of the gas? Select all that apply.
-Decrease the volume of the gas while keeping moles of gas and temperature constant.
-Remove moles of gas from the container while keeping volume and temperature constant.
-Increase the temperature of the gas while keeping volume and moles of gas constant.
-Add more moles of gas to the container while keeping volume and temperature constant.
-Expand the volume of the gas while keeping moles of gas and temperature constant.
-Decrease the temperature of the gas while keeping volume and moles of gas constant.
-Expand the volume of the gas while keeping moles of gas and temperature constant.
-Decrease the temperature of the gas while keeping volume and moles of gas constant.
How do we decrease the gas pressure?When the volume of a gas increases, the pressure decreases, as long as the temperature remains constant. This is known as Boyle's law. Therefore, one way to decrease gas pressure is to increase the volume of the container that holds the gas.
As the temperature of a gas decreases, its pressure also decreases, as long as the volume remains constant. This is known as Charles's law. Therefore, one way to decrease gas pressure is to cool the gas down.
Learn more about gas pressure:https://brainly.com/question/18124975
#SPJ1
Which one of the following correctly ranks the compounds in order of lowest enthalpy of vaporization to highest enthalpy of vaporization based only in intermolecular forces?
A) CH₃NH₂ < CH₃SH < CH₃CH₃
B) CH₃NH₂ < CH₃CH₃ < CH₃SH
C) CH₃CH₃ < CH₃SH < CH₃NH₂
D) CH₃SH < CH₃NH₂ < CH₃CH₃
Rank of the given compounds in order of lowest to highest enthalpy of vaporization as follows CH₃NH₂ < CH₃SH < CH₃CH₃.
The enthalpy of vaporization of a substance is related to the strength of its intermolecular forces. Substances with weaker intermolecular forces tend to have lower enthalpies of vaporization, as they require less energy to overcome those forces and vaporize.
In this order, the compounds have increasing strength of intermolecular forces. Methanethiol (CH₃SH) has stronger intermolecular forces than methylamine (CH₃NH₂), and both of these have stronger intermolecular forces than propane (CH₃CH₃).
This is because CH₃NH₂ and CH₃SH can form hydrogen bonds between molecules, while CH₃CH₃ can only experience weaker London dispersion forces.
Hence, the correct option is A.
To know more about vaporization here
https://brainly.com/question/486624
#SPJ4
Determine the van't Hoff factor for each of the following compounds. For ionic compounds, assume complete dissociation into cations and anions. CsCI ___C10Hg ___Na3PO4 ___
For ionic compounds, assume complete dissociation into cations and anions. CsCI,C10Hg,Na3PO4, are mentioned below.
What is compounds ?
A compound combines one or more additional substances to form a new product. The combination of two substances or elements is equal to the mass ratio for making that product. It is attached firmly, and they have equal in all ways to form a combination. The elements both are bonded together. Each compound has its chemical structure; if it breaks, it can either split into two atoms or molecules or in a single. Different types of compounds are present.
What is ionic compound ?
An ion with a positive charge is a cation, whereas one with a negative charge is an anion.
It is equal to the numbers of ions that form when an ionic compound dissolves.
if i>1, the molecules are said to be dissociated.
if i=1, the molecules have neither associated nor dissociated.
if i<1, the molecules have associated.
CsCl
vant hoff factor i= 2
C₁₀H₈
vant hoff factor i= 1
Na₃Po₄
vant hoff factor i= 3+1= 4.
Therefore, For ionic compounds, assume complete dissociation into cations and anions. CsCI,C10Hg,Na3PO4, are mentioned above.
Learn more about compounds from the given link.
https://brainly.com/question/14782984
#SPJ1
Is hydrogen found in a natural abundance
Yes, hydrogen found in a natural abundance, hydrogen is easily the most abundant element in the universe.
Why is hydrogen the most abundant in nature?Hydrogen the most abundant in nature because hydrogen is the simplest element in the universe, with only one proton and one electron ,it is the only element without a neutron.
The element hydrogen is by far the most abundant in the universe. It can be found in the sun and most stars, and the planet Jupiter is mostly made up of hydrogen. Water is the most abundant form of hydrogen on Earth.
Thus, hydrogen found in a natural abundance.
To learn more about the hydrogen, follow the link;
https://brainly.com/question/28937951
#SPJ9
identify the kind(s) of intermolecular forces that would occur between the solute and solvent in an isopropyl alcohol (which is polar and contains an oh o h group) solution.
Isopropyl alcohol (C3H8O) is a polar molecule due to the presence of an OH group. The types of intermolecular forces that would occur between the solute (isopropyl alcohol) and the solvent depend on the nature of the solvent. In general, polar solutes dissolve in polar solvents, and the intermolecular forces that occur are:
Hydrogen bonding: Isopropyl alcohol can form hydrogen bonds with other polar molecules, including water or other alcohols. Hydrogen bonds occur between the hydrogen atom of the OH group in isopropyl alcohol and the lone pair of electrons on the oxygen atom of the other molecule.
Dipole-dipole interactions: Isopropyl alcohol can also experience dipole-dipole interactions with other polar molecules. Dipole-dipole interactions occur when the positive end of one polar molecule is attracted to the negative end of another polar molecule due to their partial charges.
In summary, the intermolecular forces that would occur between isopropyl alcohol and a polar solvent, such as water or another alcohol, are hydrogen bonding and dipole-dipole interactions.
For more questions like Intermolecular forces visit the link below:
https://brainly.com/question/14744021
#SPJ4
a flask contain 0.4 moles of iron ion how many moles of Mno-4 ions must be added using a burrette to oxidize all iron ion of the ion
Permanganate ion that should be added is 0.08 moles. Based on calculation, 0.08 moles of MnO4- ions can oxidize all the iron ions in the flask.
ExplanationGiven:
Reaction between iron ion with MnO₄⁻:Therefore:
[tex]\begin{array}{ll}\sf n~MnO_4^- &\sf = \dfrac{coef. ~MnO_4^-}{coef. ~Fe^{2+}}\times n~Fe^{2+}~in\\\\&\sf =\dfrac{1}{5}\times 0.4\\\\&\sf = 0.04~moles.\end{array}[/tex]
Learn more about other moles calculation on:
https://brainly.com/question/15356425
fill in the blank. if dissociation of mgcl2 in water were 100%, the van`t hoff factor would be___; however, for real solutions the van`t hoff factor for mgcl2 is (greater than, less than) this value.
If dissociation of mgcl2 in water were 100%, the van`t hoff factor would be 3 (three); however, for real solutions the van`t hoff factor for mgcl2 is (greater than, less than) this value.
MgCl2 dissociates into three ions when it dissolves in water, giving it a theoretical van't Hoff factor of 3. The van't Hoff factor for MgCl2 is normally tested at a value of no more than 2.7.
The van't hoff factor for magnesium chloride is 3. The letter I stands for the Van't Hoff factor. One magnesium cation and two chloride ions make up the last three ions formed when magnesium chloride separates. Consequently, the magnesium chloride van't hoff factor is equal to 3.
A solute's impact on associated properties, such as osmotic pressure, relative vapor pressure reduction, boiling-point elevation, and freezing-point depression, is measured by the van 't Hoff factor i.
To know about the van't hoff factor
https://brainly.com/question/21854669
#SPJ4
Select the correct units for the rate constant in a reaction with the following rate law if concentration is measured in atmospheres and time in seconds:
Rate = k[H2]2
The unit for the rate constant of a second order reaction is [tex]L mol ^{-1} s^{-1}[/tex] . Option d is the correct answer.
Second order reactions can be defined as chemical reactions wherein the sum of the exponents in the corresponding rate law of the chemical reaction is equal to two. The rate of such a reaction can be written either as r = k[A]2, or as r = k[A][B].
The unit for the rate constant of a second order reaction is [tex]L mol ^{-1} s^{-1}[/tex] .
For a second order reaction, rate=k[A]^2.
[tex]mol L^{-1} s^{-1} = k (molL^{-1})^2[/tex]
k = [tex]L mol ^{-1} s^{-1}[/tex] .
To know more about the second order reaction, here
brainly.com/question/12446045
#SPJ4
--The complete question is, What is the unit for the rate constant of a second order reaction?
a. s^-1
b. molL^-1
c. molL^-1s^-1
d. Lmol^-1s^-1
e. mol^2L^-2s^-2--
Read the following paragraph and answer the question. "Emest Cline is an American Screenwriter and author. Emest was born in 1972. He started his writing career in 1992
doing spoken word poetry. His best known works include "Dance Monkey Dance' and 'When I Was a Kid. He then moved to film, as the screenwriter of the film Fanboys. He then released one of the most entertaining novels of all time, Ready Player One. Today Cline is still working, writing for many projects." What is the main purpose of this
paragraph?
A. To teach a moral though metaphor
B. To persuade by sharing a perspective about a subject
C. To entertain the audience
The main purpose of the paragraph is to D. To provide information about the author Ernest Cline
What is an author's purpose?The goal or objective of a writer is their motivation for writing. An author may want to parody a condition, persuade the reader, inform the reader, or amuse the reader.
The primary motivation for an author's writing is that author's purpose. The three main goals are to entertain, convince, and inform. You can determine an author's purpose by using the straightforward technique shown below.
In this case, information was provided about the character.
Learn more about purpose on:
https://brainly.com/question/13087906
#SPJ1
What is the main purpose of this
paragraph?
A. To teach a moral though metaphor
B. To persuade by sharing a perspective about a subject
C. To entertain the audience
D. To provide information about the author Ernest Cline
questions/analysis: inhaled vs exhaled air. when we inhale, the air we breathe is comprised of a lot of different gases. for the purpose if this exercise, we are going to focus on oxygen gas, carbon dioxide and water vapor. when we exhale, the same 3 gases are present, but in different amounts. 1) using the internet, estimate the percent o2 and co2 in a breath of fresh air (inhaled air). using volume of the air in the balloon and the ideal gas law formula, calculate the number of moles of o2 and co2 as well as the number of grams of each gas. show all calculations clearly.
There are approximately 0.3392 grams of oxygen and 0.00088 grams of carbon dioxide in a single breath of fresh air.
What is Concentration?
In chemistry, concentration refers to the amount of a substance (solute) that is present in a given volume or mass of another substance (solvent). It is a measure of how much of a particular substance is present in a mixture, solution, or sample.
The concentration of gases in fresh air is approximately 21% oxygen, 0.04% carbon dioxide, and 1-2% water vapor.
To calculate the number of moles of oxygen and carbon dioxide in a breath of fresh air, we need to use the ideal gas law:
PV = nRT
where P is the pressure of the gas, V is its volume, n is the number of moles, R is the gas constant, and T is the temperature in Kelvin.
Let's assume that the volume of a single breath of fresh air is 0.5 L at room temperature (25°C or 298 K) and atmospheric pressure (1 atm). We can then use the ideal gas law to calculate the number of moles of oxygen and carbon dioxide:
For oxygen:
PV = nRT
n = PV/RT = (1 atm)(0.21)(0.5 L)/(0.08206 L·atm/mol·K)(298 K) = 0.0106 mol
For carbon dioxide:
PV = nRT
n = PV/RT = (1 atm)(0.0004)(0.5 L)/(0.08206 L·atm/mol·K)(298 K) = 0.00002 mol
So there are approximately 0.0106 moles of oxygen and 0.00002 moles of carbon dioxide in a single breath of fresh air.
To calculate the mass of each gas, we can use the molar mass of each gas:
Using the number of moles we calculated above, we can calculate the mass of each gas:
Mass of oxygen = number of moles x molar mass = 0.0106 mol x 32 g/mol = 0.3392 g
Mass of carbon dioxide = number of moles x molar mass = 0.00002 mol x 44 g/mol = 0.00088 g
So there are approximately 0.3392 grams of oxygen and 0.00088 grams of carbon dioxide in a single breath of fresh air.
It's worth noting that the concentration of gases in exhaled air can vary depending on a number of factors, including the individual's health status, activity level, and surrounding environment.
Learn more about Concentration from given link
https://brainly.com/question/17206790
#SPJ4
calculate molarity if 25.0 mL of 1.75M HCl diluted to 65.0 mL 
The molarity is 0.67 M
What is molarity?Molarity is a measure of concentration used in chemistry. It is defined as the number of moles of a solute dissolved in one liter of solution. The unit of molarity is moles per liter (mol/L) or sometimes expressed as M.
Molarity is a useful way to express the concentration of a solution because it is easy to measure the volume of a solution and the amount of solute dissolved in it.
Using the dilution formula;
C1V1= C2V2
C2 = C1V1/V2
= 1.75M * 25.0 mL/65.0 mL
= 0.67 M
Learn more about molarity:https://brainly.com/question/8732513
#SPJ1
Which of the following will decrease the rate of dissolution of a gas in a liquid?
a
increase pressure
b
decrease agitation
c
increase temperature
(30 points)
According to the forces of attraction , decreasing agitation will decrease the rate of dissolution of a gas in a liquid.
What are forces of attraction?Forces of attraction is a force by which atoms in a molecule combine. it is basically an attractive force in nature. It can act between an ion and an atom as well.It varies for different states of matter that is solids, liquids and gases.
The forces of attraction are maximum in solids as the molecules present in solid are tightly held while it is minimum in gases as the molecules are far apart . The forces of attraction in liquids is intermediate of solids and gases.
Learn more about forces of attraction,here:
https://brainly.com/question/9189639
#SPJ1
click reset. drag the whole (uncut) block of polystyrene onto the material investigation tray. record its mass and volume and calculate the density.
To find the density of the polystyrene block, you will need to follow the steps outlined in the question.
1. Click "Reset" to ensure that the material investigation tray is empty and ready to use.
2. Drag the whole (uncut) block of polystyrene onto the material investigation tray.
3. Record the mass of the polystyrene block. This can typically be found using a scale or balance.
4. Record the volume of the polystyrene block. This can be found by measuring the length, width, and height of the block and multiplying them together.
5. Calculate the density of the polystyrene block by dividing the mass by the volume.
The formula for density is:
Density = Mass/Volume
By following these steps, you will be able to find the density of the polystyrene block. Remember to be accurate in your measurements and calculations to ensure that your results are correct.
To know more about polystyrene block, refer here:
https://brainly.com/question/30965100#
#SPJ11
2CO + O2 2CO2
From the equation above, what volume of the product will be formed if 50 cm3 of carbon (II) oxide reacts with 30 cm
Answer:
24.2 cm3 of CO2 will be produced.
Explanation:
This equation is balanced, meaning that the number of atoms of each element is the same on both sides of the equation. To determine the volume of the product, CO2, formed from a reaction of 50 cm3 of CO and 30 cm3 of O2, we need to consider the stoichiometry of the reaction, which states the relative proportions of the reactants and products.
The balanced equation is:
2CO + O2 -> 2CO2
This means that 2 moles of CO react with 1 mole of O2 to produce 2 moles of CO2. To determine the volume of the CO2 produced, we need to know the number of moles of CO and O2.
Assuming that the volumes of CO and O2 are measured at the same temperature and pressure, we can use the ideal gas law to convert the volumes to moles:
n = PV/RT
where n is the number of moles, P is the pressure, V is the volume, R is the gas constant, and T is the temperature.
Let's use 50 cm3 of CO as an example:
n = (1 atm)(50 cm3) / (0.08206 L * atm / mol * K)(298 K) = 0.11 moles of CO
Similarly, we can calculate the number of moles of O2:
n = (1 atm)(30 cm3) / (0.08206 L * atm / mol * K)(298 K) = 0.06 moles of O2
Since the balanced equation states that 2 moles of CO react with 1 mole of O2, we can use the smaller number of moles, 0.06 moles of O2, to calculate the number of moles of CO2 produced:
0.06 moles of O2 * 2 moles of CO2 / 1 mole of O2 = 0.12 moles of CO2
Finally, we can convert the number of moles of CO2 to a volume using the ideal gas law:
V = nRT/P = (0.12 moles)(0.08206 L * atm / mol * K)(298 K) / (1 atm) = 24.2 cm3
So, if 50 cm3 of CO and 30 cm3 of O2 react, 24.2 cm3 of CO2 will be produced.
This question is based on the Subduction Zones topic in the Tsunami Initiation Animation. Click here to access it. 1st attempt The initiation of a tsunami by a stick-slip subduction zone is similar to the motion experienced by which type of fault?
The initiation of a tsunami by a stick-slip subduction zone is similar to the motion experienced by reverse fault.
A reversal fault experiences similar motion as a stick-slip subduction zone when it starts a tsunami. The majority of tsunamis are created by subduction zones, which result in earthquakes when two tectonic plates collide beneath the ocean and encourage the movement of overlapping water.
The energy that builds up as a result of the friction between the plates increases to the point where it may be extrapolated to the limit between the two plates. When a reverse failure occurs in this process, the movement experienced by a reverse failure is analogous to the start of a tsunami through a stick-slip subduction zone.
Learn more about reverse fault at https://brainly.com/question/2307144
#SPJ4
Which of the following would be considered to be supersaturated if 40g of solute were dissolved at 60ºC?
a
KCl
b
KClO3
c
NaCl
(30 points)
KCl would be considered to be supersaturated if 40g of solute were dissolved at 60ºC.
Option A is correct.
What is a supersaturated solution?A supersaturated solution is described as a solution that contains more than the average solvent that can be dissolved at a given temperature
At 60ºC, the solubility of KCl is about 42g/100mL of water. Therefore, since we have 40g of KCl that were dissolved in less than 100mL of water, the solution would be supersaturated.
In conclusion, supersaturation occurs with a solution when the concentration of a solute exceeds the concentration specified by the value of solubility at equilibrium.
Learn more about a supersaturated solution at: https://brainly.com/question/17592745
#SPJ1
or which of the following molecules would the intermolecular forces be influenced mainly by hydrogen bonding? BrF5 C2H5OH H2S CH3NH INFLUENCE OR NOT
The molecules that would have the intermolecular forces be influenced mainly by the hydrogen bonding is C₂H₅OH , CH₃NH₂.
The Hydrogen bonding is the special type of the dipole-dipole attraction between the molecules, but not the covalent bond to the hydrogen atom. It will results from the attractive force in between the hydrogen atom that are covalently bonded to the more electronegative atom such as the N, O, or F atom and the another very electronegative atom. The hydrogen bonding, is the interaction that involves a hydrogen atom that is located in between a pair of the other atoms having the high affinity for the electrons
Thus, C₂H₅OH , CH₃NH₂ both molecules influenced by the hydrogen bonding.
To learn more about hydrogen bonding here
https://brainly.com/question/12514139
#SPJ4
Draw a Newman projection along the C2 - C3 bond of the following conformation of 2,3-dimethyl butane, and calculate the total strain energy.
The total strain energy can be estimated by adding up the contributions from each type of strain. For the eclipsed conformation of 2,3-dimethylbutane, the total strain energy is approximately 3.8 kcal/mol.
To draw a Newman projection of 2,3-dimethylbutane along the C2-C3 bond, we need to imagine looking along that bond and represent the carbon atom that is closer to us as a point (•) and the carbon atom that is farther away as a circle (o). We then draw the substituents on each carbon as follows:
To calculate the total strain energy of this conformation, we need to consider the various types of strain that are present.
The main sources of strain in this conformation are:
Torsional strain: The eclipsed conformation of the C2-C3 bond creates torsional strain.
The dihedral angle between the two methyl groups is 0°, which means they are eclipsed and experience torsional strain.
Steric strain: The two methyl groups are close to each other and experience some degree of steric strain.
For more questions on Newman projection
https://brainly.com/question/13719268
#SPJ4
the negative electrons are in the outermost orbits and are involved in chemical reactions. they determine the chemical of an atom.
The negative electrons are in the outermost orbits and are involved in chemical reactions. they determine the chemical of an atom. (FALSE)
It should be valence electrons.
Definition of Valence ElectronsIn predicting a chemical reaction that will occur, it is necessary to take into account the number of electrons contained in an atom. In addition, valence electrons play a role in chemical bond formation reactions. Valence electrons are the outermost electrons in atoms which have the highest energy level and are involved in chemical bonds. Valence electrons are located farther from the nucleus of the atom, so that the electrons of one atom can be attracted more or less by the nucleus than the nuclei of other atoms.
An atom tends to be unreactive or stable (inert) so it is difficult to interact with other types of atoms when the valence electrons are fully filled, which resembles s2p6. Meanwhile, an atom tends to be reactive if there is an excess of one or two atoms resembling groups IA, IIA, and IIIA. However, there are also atoms that lack a few electrons, which are called more reactive, such as groups XVIA and XVIIA.
Petrucci R.H., Harwood W.S. and Herring F.G. in General Chemistry in 2002 states that:
" In the main group elements, valence electrons are defined as the electrons in the electron shell with the highest principal quantum number, n."
The number of valence electrons an atom has depends on its electron configuration.
Your question is incomplete but most probably your full question was:
Determine True/False! the negative electrons are in the outermost orbits and are involved in chemical reactions. they determine the chemical of an atom.
Learn more about Valence Electrons at
https://brainly.com/question/371590
#SPJ4
Question: (a) Use bond-dissociation enthalpies from Table 4-2 (page 203), calculate the heat of reaction for each step in the free-radical bromination of methane.
Br2 + CH4 -------(heat/light)----> Ch3Br + HBr
(b) Calculate the overall heat of reaction.
a.The heat of reaction for each step in the free-radical bromination of methane is kJ/mol = -138.8 kJ/mol.
b.The overall heat of reaction is -40.3 kJ/mol
(a) The heat of reaction for each step in the free-radical bromination of methane can be calculated using the bond-dissociation enthalpies from Table 4-2.
For the first step, the heat of reaction is equal to the sum of the bond-dissociation enthalpies of Br2 and CH4, which is -104.2 kJ/mol + -74.9 kJ/mol = -179.1 kJ/mol.
For the second step, the heat of reaction is equal to the sum of the bond-dissociation enthalpies of Ch3Br and HBr, which is -102.4 kJ/mol + -36.4 kJ/mol = -138.8 kJ/mol.
(b) The overall heat of reaction can be calculated by subtracting the heat of reaction for the second step from the heat of reaction for the first step. The total heat of reaction for the free-radical bromination of metha is calculated as follows: -179.1 kJ/mol - (-138.8 kJ/mol) = -40.3 kJ/mol.ne.
ledarn more about dissociation Refer:brainly.com/question/2224641
#SPJ4
ompound x is found to have a molar mass of 1000.7 g /mol. find the number of moles in 25.1085 g of x. make sure you include the right number of significant figures. answer
Number of moles = 0.0250839 mol (rounded to 7 significant figures) of compound X in 25.1085 g, we need to divide the given mass by the molar mass of X.
Using the given molar mass, we have calculated the number of moles of X in 25.1085 g to be 0.0250839 mol. We should round this value to the appropriate number of significant figures based on the given data. Since the mass is given to 7 significant figures.
Molar mass is the mass of one mole of a substance, usually expressed in units of grams per mole (g/mol). It is calculated by adding up the atomic masses of all the atoms in a molecule.
The molar mass of an element is equal to its atomic mass in grams per mole. For example, the molar mass of carbon is 12.01 g/mol, which is the atomic mass of carbon rounded to two decimal places.
Number of moles = Mass ÷ Molar mass
Number of moles = 25.1085 g ÷ 1000.7 g/mol
Number of moles = 0.0250839 mol
To know more about moles here
https://brainly.com/question/24748125
#SPJ4
Which of the following is the correct conversion factor (as written) required to convert a distance of 12 mi to feet, if 1 mi=5280 ft? Click the answer you think is right. - 1 mi/5280 ft - 1 mi x 5280 ft - 5280 ft/1 mi
The feet is a standard unit of measurement. It is mainly used to measure the length of a particular object. Here 12 mi is 63,360 feet. The correct option is B.
What is feet?The unit of measurement which is generally used to measure height, length and distance is defined as the feet. The foot is the singular form of feet. It is a non-metric measure unlike meters and centimeters which are metric.
Here 1 mi = 5280 ft
Then,
12 mi = 12 × 5280
= 63,360 feet
Thus the correct option is B.
To know more about feet, visit;
https://brainly.com/question/20961245
#SPJ1
FILL IN THE BLANK. A gas is ____ and assumes _____ of its container whereas a liquid is ____ and assumes _____ of its container.
A gas is compressible and assumes the volume and shape of its container whereas a liquid is not compressible and assumes the shape of a portion of its container.
What is compression?
The process of compression involves gradually reducing the system's volume while increasing pressure and temperature, with or without the possibility of heat transfer. Heat transmission may or may not be achieved during the expansion phase since volume steadily decreases as pressure and temperature fall.
The act, process, or outcome of compressing; the condition of being compressed. Compressing an internal combustion engine's fuel mixture is one example of compressing.
With each advance and retreat of the piston, a four-part cycle of compression takes place inside the cylinder (two strokes per cycle). Compression, discharge, expansion, and intake comprise the cycle's four functional components.
To know more about compression, check the link below:
https://brainly.com/question/7602497
#SPJ4
the reactions drawn show possible arrow pushing mechanisms. considering what you know about arrow pushing mechanisms, identify which show incorrect arrow pushing. select the incorrect mechanisms. x has a plus charge and is bonded to y, which is bonded to z, which has a negative charge and a lone pair. a curved arrow starts from the lone pair of z and points to x. the product is a 3 atom ring, with x bonded to y bonded to z, which is bonded to x. x is double bonded to y. a curved arrow starts from the pi bond and points to z, which has a plus charge. the product is x which has a plus charge and is bonded to y, which is bonded to z. x is bonded to y. a curved arrow starts from the bond and points to y. the products are x minus and y plus. x is bonded to y. a curved arrow starts from the bond and points to z, which has a plus charge. the product is x bonded to y bonded to z. x has a lone pair and negative charge and is bonded to y, which has a plus charge. a curved arrow starts from the lone pair and points to the bond. the product is a double bond between x and y.
The arrow pushing mechanisms shows the steps in the reaction.
What is the use of arrow pushing mechanisms in reactions?The question is incomplete but I can see that you want to know something about a reaction that uses an arrow pushing mechanisms to show the steps in the reaction.
Arrow pushing mechanisms are graphical representations used in organic chemistry to show the flow of electrons in a reaction. The arrow symbol is used to represent the movement of electrons from one molecule to another. This makes it easier for chemists to understand and predict the outcome of a reaction by showing the transfer of electrons between reactants and products.
The arrow pushing mechanism provides a step-by-step description of the reaction, starting from the reactants and showing the intermediate stages before reaching the final product. This makes it easier to identify and understand the individual steps involved in a reaction and how they are connected.
Learn more about arrow pushing mechanisms:https://brainly.com/question/28206831
#SPJ1
the rections above involve synthesis or reactions of alcohols and ethers. identify the mechanism by which they proceed from among the mechanisms listed. use the letters a - g for your answers.
There are several mechanisms that can be involved in the synthesis or reactions of alcohols and ethers, depending on the specific reaction and the type of alcohol or ether involved. Here are some common mechanisms that may be involved:
a. Nucleophilic substitution: This mechanism is often involved in the synthesis of ethers from alkyl halides or sulfonates. In this mechanism, a nucleophile attacks the electrophilic carbon of the alkyl halide or sulfonate, displacing the leaving group and forming a new carbon-oxygen bond. In the case of the Williamson ether synthesis, an alkoxide ion acts as the nucleophile and attacks the alkyl halide.
b. Dehydration: In the presence of acid catalysts, alcohols can undergo dehydration to form ethers. This mechanism involves the loss of a water molecule from two alcohol molecules and the formation of an ether linkage.
c. Acid-catalyzed cleavage: Ethers can be cleaved into two alcohol molecules using acid catalysts. This mechanism involves the protonation of the oxygen atom, followed by nucleophilic attack of water or alcohol.
d. Nucleophilic addition: Ethers can undergo nucleophilic addition reactions with strong acids such as HBr or HI to form alkyl halides and alcohols. This mechanism involves the protonation of the oxygen atom, followed by nucleophilic attack of the halide ion.
e. Oxidation: Primary alcohols can be oxidized to form ethers using oxidizing agents such as HIO4. This mechanism involves the oxidation of the alcohol to an aldehyde, which then reacts with another alcohol molecule to form the ether.
f. Acid-catalyzed transetherification: Ethers can react with alcohols in the presence of acid catalysts to form different ethers. This mechanism involves the protonation of one of the oxygen atoms, followed by nucleophilic attack of the alcohol on the other oxygen atom, leading to the formation of a new ether.
g. Acid-catalyzed dehydration of secondary alcohols: Secondary alcohols can undergo acid-catalyzed dehydration to form alkenes and ethers. This mechanism involves the loss of a water molecule from the alcohol, which can lead to the formation of an alkene or an ether depending on the reaction conditions.
To know more about ethers here
https://brainly.com/question/28047849
#SPJ4