Answer:
S2 = 60 RPM.
Explanation:
Given the following data;
Gear ratio = 40/24 (T2 = 40 and T1 = 24).
Speed of driving gear = 100 RPM
To find the speed of the driven gear;
Mathematically, gear ratio in terms of speed (RPM) is given by this formula;
[tex] S_{1} * T_{1} = S_{2} * T_{2} [/tex]
Where;
S1 represents the speed of the driver gear.S2 represents the speed of the driven gear.T1 represents the number of teeth of the driver gear.T2 represents the number of teeth of the driven gear.Substituting into the equation, we have;
[tex] 100 * 24 = S_{2} * 40[/tex]
[tex] 2400 = 40S_{2} [/tex]
[tex] S2 = \frac {2400}{40} [/tex]
S2 = 60 RPM.
Therefore, the speed of the driven gear is 60 revolutions per minute.
The cylinder should always be securely held in an upright position
Compressed gas cylinders shall be secured in an upright position at all times except, if necessary, for short periods of time while cylinders are actually being hoisted or carried.
Why do gas cylinders need to be upright?All gas cylinders must be stored upright and restrained with safety chains or other secure devices, as stated in AS4332-2004 - The storage and handling of gases in cylinders.
Acetylene cylinders should be stored upright in order to avoid the gas from separating from the acetone. All compressed gas cylinders, whether filled, half filled, or empty, must comply with the standard.
The cylinders are designed exclusively for use in the gas phase, which emerges when the cylinder is held upright. Liquid leakage occurs when the cylinder is used horizontally, which has negative effects. Gas cylinders should never be used horizontally. They might leak, which might be extremely dangerous.
To learn more about upright position refer to:
https://brainly.com/question/14400427
#SPJ1
Drivers Education Unit 3
What is the relationship between weather conditions, human-perception time, vehicle-reaction time, and dangerous traffic situations? What can the driver do to make sure he or she is prepared to allow for such situations?
The relationship between weather conditions, human-perception time, vehicle-reaction time, and dangerous traffic situations is known to be one that is interwoven as one cannot do without the other.
What are the factors that affect perception reaction time?A lot of factors have been seen to affect reaction times, such as age, gender, physical fitness and others.
Hence, The relationship between weather conditions, human-perception time, vehicle-reaction time, and dangerous traffic situations is known to be one that is interwoven as one cannot do without the other.
The driver need to be sensitive to make sure he or she is prepared to allow for such situations.
Learn more about weather conditions from
https://brainly.com/question/17922964
#SPJ1
Summarize key
points from each
paragraph
READING Customer Service
Learning Seed: Communicating with Customers
What Makes Good Customer Service?
When you work in a retail store, what services are you offering? You
may think that your employer is paying you to prepare food, stock
shelves or tidy up the sales floor, but those aren't the real reasons.
Your employer is paying you to serve the needs of his or her
customers. Without good customer service, the customers would
disappear, and without customers, the business would fail. How you
treat the customers has a big impact on how well the store succeeds.
So what makes good customer service? The main ingredient is trying
to understand the customer. Understanding what a customer wants,
doesn't want, and how he or she wants to be treated are the keys to
having happy customers. There are many components to good
customer service, but in the end they all come down to the same goal:
understanding your customers.
Successful (And Not-So-Successful) Interactions What are the key points?
Answer:
what are is ethiopia cultural ?
What is the difference between traditional heavy timber frame construction and post-and-beam framing?
However, the way the various components are joined makes post and beam building different from timber frame construction: Wood joinery and infrequently steel components are used in timber framing. Metal fasteners and connectors are used in post and beam structures.
What kind of traditional timber framing is most prevalent?By far the most prevalent type of surviving timber-framed construction is post and truss (see below right). The purlin roof is used in this design. Each cross frame contains structural connections between the roof and wall components. Like in box-framed construction, the tie beams are part of the cross frames.
What is the alternative term for post and beam architecture?Terminology used nowadays. The phrase "post-and-beam" is frequently used in a fairly broad sense, but the term "timber frame" is used to describe a particular subset of structures—those that are built using wood.
To know more about connectors visit:-
https://brainly.com/question/13605839
#SPJ1
construct a plain scale 30mm =10mm and 50mm long to read to one mm
follow these steps:
Start by cutting a strip of paper or cardstock to a length of 50mm. This will be the base of your scale.
On the left side of the strip, mark a point at the 0mm mark, this will be the starting point of your scale.
Using a ruler, mark off 10mm increments to the right. You will have a total of 5 marks (10mm, 20mm, 30mm, 40mm, and 50mm)
At the 30mm mark, mark a point that is 3mm to the right of the 30mm mark, this will be the end of your scale.
Lastly, use a ruler to divide each 10mm segment into 1mm increments. You will have a total of 30mm on your scale that can be read to 1mm.
Your scale should look like this:
0mm | 10mm | 20mm | 30mm | 30.3mm | 40mm | 50mm
It's important to note that this a plain scale and it does not have any graduation marks on it, it is intended to be used as a reference to measure the length of an object and compare it with the scale.
Which statement describes why genetic engineering is a new field?
Genetic engineering may involve adding a gene from one species to an organism from a different species to produce a desired trait.
Which statement describes why genetic engineering is a new field?Genetic engineering has been used in research and business to produce cancer treatments, brewing yeasts, genetically altered plants and animals, among other things.
Genetic engineering, often known as genetic alteration, is a technique that modifies an organism's DNA using technology developed in labs. This could entail altering a single base pair (A-T or C-G), erasing a section of DNA, or incorporating new DNA.
For instance, transferring a gene from one species to an organism from a different species in genetic engineering may result in the desired characteristic. Genetic engineering has been used in research and business to produce cancer treatments, brewing yeasts, genetically altered plants and animals, among other things.
To learn more about Genetic engineering refer to:
https://brainly.com/question/2780091
#SPJ1
HELP ME QUICKLY PLEASE
What should you do after you have received feedback about your project?
A. Add three images
B. Revise it and make changes
C. Submit it to the instructor
D. Write the first draft
Answer: B
Explanation:
You should revise it and make changes according to the feedback you recieve.
What’s the answer to this I don’t understand
Answer:
Electrons are the negatively charged particles of atom. Electrons are extremely small compared to all of the other parts of the atom. So, the negative green particles of this atom are the electrons.
Explanation:
Hope it helps:)
Why is technology influence in music good?
Which article of the NEC describes the proper placement of outlets in this type of room? Also, based on the given load what type of outlets are needed for this room?
The Article of the NEC that describes the proper placement of outlets in rooms is the Article 210.
What is NEC?
NEC is the short or acronym for National Electric Code.
For example, with regard to Receptacles, section (210-21(b)) of the Article 100 indicates that a "Receptacle" is a contact device provided at an outlet for the connecting of an attachment plug.
The terms "receptacle" and "receptacles" occur often in the National Electrical Code (NEC).
Learn more about NEC at;
https://brainly.com/question/14507799
#SPJ1
9. What is the setting-down machine used for?
In order to get ready for the double sewing machine, the Setting Down Machine seals the flanged seam that was created using the Burring Machine.
What is meant by Setting Down Machine ?For the Double Seaming Machine, the Setting Down Machine completes the flanged seam that was created with the Burring Machine.
An adjustable and spring-loaded axel on the crank and two gear-shaped disc dies arranged at a 90-degree angle are features of this hand-operated device. a rounded, knurled mounting hole for mounting in a cast iron stand is located at the bottom of the frame.
The first American patents for devices created by Eli Parsons and Calvin Whiting to carry out part of the tinsmith's duties were granted at the start of the nineteenth century. The two had an agreement with Seth Peck of Stonington, Connecticut, around 1810, who produced and continuously enhanced the devices before buying the patents from Parsons and Whiting. Peck also built and developed the machines. This practical tool, known as a "setting-down machine," was used to firmly put down the folded edge of a piece of tin.
To learn more about setting-down machine refer to:
https://brainly.com/question/17193473
#SPJ1
How can you determine the driver & driven gears in a gear train?
The driver gear is the gear that provides the power to turn the other gears in the gear train, while the driven gear is the gear that is turned by the driver gear.
How to identify the driver?One way to determine the driver and driven gears is to identify the gear that is connected to the power source, such as a motor or engine, as this gear would be the driver.
The gear(s) connected to this gear and turning as a result is the driven gear.
Another way is to observe the direction of rotation of the gears, the gear that is rotating clockwise is the driver and the gear which is rotating anticlockwise is the driven gear.
Read more about gear trains here:
https://brainly.com/question/21513540
#SPJ1
duties of school principal
The duties of school principal are those responsibilities or obligation he must carry out for proper management of the school. Some of the duties are as follows:
Supervision of instructionSupervision of Curriculum Development and ImprovementSupervision of curricula rand Co-curricular ActivitiesSupervision of School HostelWhat is school administration?School administration can simply be defined as process which involves the management of all the school operations and activities.
Learn more about school administration:
https://brainly.com/question/24243635
#SPJ1
Here are three displacements, each in meters: d₁ = 7.61 +2.5) - 3.4k, d₂ = - 1.01 + 2.0 + 3.0k, and d3 = 4.01 +3.0 +2.0k. What is 7 = d₁ - d₂ + d3 ((a), (b) and (c) for î, j and k components respectively)? (d) What is the angle between 7 and the positive z axis? (e) What is the component of d along the direction of d2? (f) What is the component of d, that is perpendicular to the direction of d2 and in the plane of d, and d₂? 1
Answer:
a) The i-component of 7 is (7.61 + 2.5) - 3.4k = 7.61 + 2.5 - 3.4k
b) The j-component of 7 is -1.01 + 2.0 + 3.0k = -1.01 + 2.0 + 3.0k
c) The k-component of 7 is 4.01 + 3.0 + 2.0k = 4.01 + 3.0 + 2.0k
d) To find the angle between 7 and the positive z-axis, we need the dot product of 7 and the unit vector along the positive z-axis (0,0,1). The dot product is given by:
(7.61 + 2.5 - 3.4k)(0) + (-1.01 + 2.0 + 3.0k)(0) + (4.01 + 3.0 + 2.0k)(1)
And the angle between 7 and the positive z-axis is given by the following formula:
cos(theta) = (7.dot.unit_vector_z_axis) / (||7||.||unit_vector_z_axis||)
e) To find the component of d along the direction of d2, we need to find the projection of d on d2. The projection is given by the dot product of d and d2 divided by the square of the magnitude of d2.
f) The component of d that is perpendicular to the direction of d2 and in the plane of d and d2 is given by the vector subtracting the component of d along the direction of d2 from the original vector d
a) The i-component of 7 is (7.61 + 2.5) - 3.4k = 7.61 + 2.5 - 3.4k
b) The j-component of 7 is -1.01 + 2.0 + 3.0k = -1.01 + 2.0 + 3.0k
c) The k-component of 7 is 4.01 + 3.0 + 2.0k = 4.01 + 3.0 + 2.0k
d) To find the angle between 7 and the positive z-axis, we need the dot product of 7 and the unit vector along the positive z-axis (0,0,1). The dot product is given by:
(7.61 + 2.5 - 3.4k)(0) + (-1.01 + 2.0 + 3.0k)(0) + (4.01 + 3.0 + 2.0k)(1)
And the angle between 7 and the positive z-axis is given by the following formula:
cos(theta) = (7.dot.unit_vector_z_axis) / (||7||.||unit_vector_z_axis||)
e) To find the component of d along the direction of d2, we need to find the projection of d on d2. The projection is given by the dot product of d and d2 divided by the square of the magnitude of d2.
f) The component of d that is perpendicular to the direction of d2 and in the plane of d and d2 is given by the vector subtracting the component of d along the direction of d2 from the original vector d
Learn more about perpendicular
https://brainly.com/question/18271653
#SPJ1
When a component uses less than one or two volts for operation, it is _____.
When a component uses less than one or two volts for operation, it is Low
What is a volt?In the International System of Units, the volt is the unit of electric potential, electric potential difference, and electromotive force. It is named after Alessandro Volta, an Italian scientist.
Voltage is the force exerted by the power source of an electrical circuit to move charged electrons (current) through a conducting loop, allowing them to do work such as lighting a lamp. In a nutshell, voltage equals pressure and is measured in volts (V).
Learn more about Volt:
https://brainly.com/question/28675147?
#SPJ1
What's the conducting element
between the two ferrules called?
Wire ferrules is the conducting element
between the two ferrules
What are elctrical wire ferrules?An electric wire ferrules are metal tubes which are usually crimped over stranded wire to secure the strands within a screw terminal.
The three major types of wire ferrules are as follows:
Insulated, Non-Insulated Twin InsulatedIn conclusion, wires ferrules is the conducting element between the two ferrules
Learn more about metallic wire elements:
https://brainly.com/question/9222909
#SPJ1
What is the purpose of this block?
list add value
to end
A. To insert the first value in an array
B. To remove the last value from an array
C. To change a value at a certain index.
D. To add a value to the end of an array
The purpose of a block to add a value to the end of an array.
What is the function that adds an element to the end of an array?The push() is known to be often used to add an element to the end of your array.
The end() function is known to be one that transmit the internal pointer to, and also the outputs, the last factor in the array.
A null or zero value is known to be that which marks the end of an array and it is said to be the very equivalent of the null char for any kind of string
Hence, in the above scenario, The purpose of a block to add a value to the end of an array.
Therefore, option D is correct.
Learn more about array from
https://brainly.com/question/24275089
#SPJ1
Answer: The answers is C. To change a value at a certain index
I just took the test
Research and find out whether any laws or guidelines exist for robotics. Describe these guidelines.
Answer:
1.A robot may not injure a human being or, through inaction, allow a human being to come to harm.
2.A robot must obey the orders given it by human beings except where such orders would conflict with the First Law.
3.A robot must protect its own existence as long as such protection does not conflict with the First or Second Laws.
Explanation:
what car do you think it is
Answer:
Benz
Explanation:
because it looks like it
What is the difference between chronic and acute effects when talking about toxins?
A single, brief encounter causes acute poisoning. Effects frequently manifest fast and can be reversed. Repeated exposure over a lengthy period of time leads to chronic toxicity.
What distinguishes a toxin's acute effects from its long-term effects?Chronic exposure is a word for prolonged exposure. Both might have an impact on health. Acute exposure refers to a brief encounter with a substance. It could linger for a short while or several hours.
What distinguishes an acute toxicity test from a chronic toxicity test?Acute toxicity tests are quick assessments of the results of exposure to substances at relatively high concentrations. Testing measuring the effects of exposure to relatively lower, less dangerous amounts over a longer period of time are known as chronic toxicity tests.
To know more about acute effects visit:-
https://brainly.com/question/14325364
#SPJ1
What is the wiring machine used for?
A wiring system is a network of wires that links various accessories for the distribution of electrical energy from the supplier metre board to a number of electrical energy-consuming devices.
What is a wiring system?Winding the linear object on a particular workpiece is the automatic wire coiling machine's primary task. The automatic wire coiling equipment is more widely used in daily life and by numerous manufacturers.
A wiring system is a network of wires that connects various accessories for the distribution of electrical energy from the supplier metre board to a range of electrical energy-consuming devices including lamps, fans, and other household appliances via regulating and safety devices.
It is also known as a pull drawing machine while drawing wire. The production of machinery, the processing of metals, petrochemicals, the manufacture of plastics, bamboo and wood products, wire and cable, and other industries all use wire drawing machines, which are common mechanical devices used in industrial applications.
To learn more about wiring machine refer to:
https://brainly.com/question/2587643
#SPJ1
A first class lever has a 180 lb. FR and 30 lb. effort force. The lever’s FE is located 6 ft from the fulcrum. What is the actual mechanical advantage of the system?
Answer:6
Explanation: To calculate the actual mechanical advantage (AMA) of a first-class lever, we use the following formula:
AMA = load/effort
In this case, we know that the load (FR) is 180 lb and the effort (FE) is 30 lb. So we can plug these values into the formula:
AMA = 180 lb / 30 lb
AMA = 6
So the actual mechanical advantage of the system is 6, meaning that for every 1 lb of effort applied, the load moves 6 lbs.
The load distance is given as 6 ft, but it is not used to calculate the AMA in this case. The AMA is calculated only from the ratio of load and effort forces.
Name the views 1-4, of the VEX 5 Clawbot shown in the picture below
Select the Vision Sensor Configure button in VEXcode V5 after you've connected. Then choose the Freeze button while something is in front of the Vision Sensor. Drag a bounding box around the selected image on the screen. Afterward, pick one of the seven signature slots.
What are the top 5 parts of robots?Manipulators, End Effectors, Feedback Devices, Controllers, and Locomotive Devices are an industrial robot's primary components.
What are the 5 sensor categories?Smart sensors come in a variety of forms, but the ones that are most frequently used include level sensors, electric current sensors, humidity sensors, pressure sensors, temperature sensors, proximity sensors, heat sensors, flow sensors, and fluid velocity sensors.
To know more about VEX visit:-
https://brainly.com/question/26709985
#SPJ1
Can someone help here’s a picture
Answer:
6--b
7--a
8--c
9--f
10--d
Explanation:
6. Miter saw/circular blade with perimeter teeth (b.wood/metal sheet)
7. Miter saw/circular blade with 60+ teeth. (a.ceramic tile)
8. Circular saw/circular blade with abrasive. (c. fine cuts on expensive molding)
9. Reciprocating saw/straight blade, bimetal. (f. solid metal)
10. Circular saw/circular blade with grinding edge, dry. (d. demolition having old nails)
About circular sawA circular saw is a type of cutting tool in the form of a chainsaw with a round and serrated saw blade. With this type of saw, cutting wood becomes easier. Not only that, Circular Saw is also often chosen because of the practicality of its use. In addition, this circular saw is also very practical to remove. So if the saw blade is dull, then you can easily remove it to be sharpened again, or replaced with a new one.
Learn more about circular saw at
https://brainly.com/question/17157503
#SPJ1
How do you determine which beam formula to use?
Deflection is often determined by taking the double integral of the Bending Moment Equation, M(x), and dividing it by EI (Young's Modulus x Moment of Inertia).
How do you use beam deflection formula?Deflection is often determined by taking the double integral of the Bending Moment Equation, M(x), and dividing it by EI (Young's Modulus x Moment of Inertia).The size-determining steps are:determine the live load per foot of the beam as well as the total load.The kind of load you are supporting, please specify (roof snow, non snow or floor). Choose the required span.To the values shown in the tables, compare the total load and live load figures.The required member will be mentioned with its thickness and depth.A structural beam's stress and deflection are measured using a beam calculation when a specific load is applied to the beam.Another factor utilized in beam calculations is the force per unit length, which depends on the type of load.To learn more about Beam deflection refer
https://brainly.com/question/13507665
#SPJ1
what are the inputs and outputs of a sailboat?
Answer:
sailing ships were the primary means of maritime trade and transportation; exploration across the seas and oceans was reliant on sail for anything other than the shortest distances. Naval power in this period used sail to varying degrees depending on the current technology, culminating in the gun-armed sailing warships of the Age of Sail.Think of a situation in the not-too-distant future in which an autonomous robot, for example a factory manufacturing robot or a self-driving car, through some unfortunate coincidental combination of circumstances accidentally causes a human serious injury or even death. In a case such as this, who should be held responsible for the crime and damages? Can the developer or team of developers who wrote the code justifiably be held responsible? Is it simply considered a mechanical malfunction and nobody is held responsible, but the machine is destroyed?
I feel that the developer or team of developers who built the code should not be held accountable; rather, the organization that approved its use should be held accountable.
What exactly is self-driving technology?A self-driving car is also known as an autonomous car or simply a driverless car because it is a vehicle that uses sensors, cameras, and artificial intelligence (AI) in its operations.
Therefore, Notably, in the preceding case, I feel that the developer or team of developers who built the code should not be held accountable; rather, the organization that approved its use should be held accountable.
To learn more about the autonomous robot, refer to the link:
https://brainly.com/question/24187446
#SPJ1
A b c or d?????? Please help
Answer:
Explanation:
D Stationary measurement
Social Media is a website or online channel that enables users to exchange online generated content.
True or false
Answer:
False
Explanation:
It's not all online-generated content.
Social Media is a website or online channel that enables users to exchange online generated content, is the false statement.
What is Social Media?Websites and programs that emphasize collaboration, sharing of content, engagement, and community-based feedback are collectively referred to as social media. Social media is used by people to connect and communicate with their friends, family, and other communities.
Although there are other methods to categorize social media, the six main categories are social networking, bookmarking, social news, media sharing, microblogging, and online discussion forums.
Social media is used by billions of people worldwide to connect and share information. Social media gives you the personal freedom to interact with loved ones, learn new things, explore new interests, and be entertained.
Thus, it is the false statement.
For more information about social Media, click here:
https://brainly.com/question/29616595
#SPJ2
How can you tell if you need to solve the problem as if the effort is applied at the axle or applied at the wheel if not stated in the problem?
When an axle is exerted, the force on the system decreases while the torque on the axle increases as a result of the effort, which results in
In science, what exactly is a force?
In science, "force" refers to a certain concept. It is quite acceptable to refer to a force of this level as a push or a pull. It's incorrect to say that an object "has in it" or "contains" a force. A force is experienced by one thing from another. The concept of a force makes no distinction between living creatures and inanimate objects. Force is defined as a push or pull that causes the body it is acting on to accelerate. The unit of force in the SI is the Newton.
Know more about increases Visit:
https://brainly.com/question/9895771
#SPJ1