The void in mineral aggregate (VMA) is -12.35%, the void in total mix (VTM) is 0.000990 and the voids filled with asphalt (VFA) is -12.35%.
To determine the VMA, VTM, and VFA neglecting absorption, we need to calculate the following:
[tex]VMA = [(Gmb - Gsb) / Gmb] \times 100[/tex]
[tex]VTM = Gmb / ρb[/tex]
[tex]VFA = [(Gmb - Ga) / Gmb] \times 100[/tex]
Where, Gmb = bulk specific gravity of the compacted specimen of HMA.
Gsb = bulk specific gravity of the aggregate in the HMA specimen.
ρb = bulk density of the HMA specimen
Ga = apparent specific gravity of the aggregate in the HMA specimen.
Substitute the given values we get:
[tex]Gmb = 2.435, Gsb = 2.735, \rho b = 2455\ kg/m^3[/tex],
[tex]Ga = (Gmb \times Gsa) / (5.1 + 0.049 (Gmb - 2.435)) = (2.435 \times 2.735) / (5.1 + 0.049 (2.435 - 2.435)) = 2.449[/tex]
By substituting these values in the above formula, we get:
[tex]VMA = [(2.435 - 2.735) / 2.435] \times 100 = -12.35[/tex]%
[tex]VTM = 2.435 / 2455 = 0.000990[/tex]
[tex]VFA = [(2.435 - 2.735) / 2.435] \times 100 = -12.35[/tex]%
Hence, VMA = -12.35%, VTM = 0.000990, VFA = -12.35%.
The minus sign indicates that the voids are insufficient. Therefore, the mix is unstable.
Learn more about specific gravity:
https://brainly.com/question/20422535
#SPJ11
A train is moving up a steep grade at constant velocity (see following figure) when its caboose breaks loose and starts rolling freely along the track. After 5.0 s, the caboose is 30 m behind the train. What is the acceleration of the caboose?
The velocity of the caboose is constant, so the acceleration is zero. Therefore, the caboose's acceleration is 0 m/s².
Acceleration is the rate at which the velocity of an object changes over time. The formula for acceleration is expressed as a = (v - u) / t where a is acceleration, v is final velocity, u is initial velocity, and t is time.
The velocity of the train and the caboose is the same. The caboose breaks loose and starts rolling freely along the track. Therefore, the velocity of the caboose is the same as the velocity of the train.
Given that the train moves at a constant velocity, the initial velocity of the caboose is the same as the final velocity.
Using the formula above, the acceleration of the caboose is calculated as follows:
a = (v - u) / ta
= (0 - 0) / 5.0
a = 0 m/s²
Therefore, the acceleration of the caboose is 0 m/s². This result makes sense since the caboose is moving at constant velocity.
Learn more about Acceleration here:
https://brainly.com/question/460763
#SPJ11
mastering astronomy based on current evidence, how common are planetary systems? based on current evidence, how common are planetary systems? all stars should have planets orbiting around them. only 10 % of stars have planetary systems. about 70 % of stars have planetary systems. almost exactly half of stars have planetary systems.
Based on current evidence, planetary systems appear to be relatively common.
What is current evidence?Current evidence suggests that regular physical activity can improve physical and mental health, reduce the risk of developing chronic diseases, and promote well-being. Studies have found that regular exercise can reduce stress, improve mood, improve sleep quality, and increase energy levels. Exercise can also reduce the risk of developing heart disease, stroke, diabetes, and certain types of cancer. Additionally, regular physical activity can help to maintain a healthy weight, reduce the risk of osteoporosis, and improve cognitive function.
Studies using data from the Kepler Space Telescope suggest that around 70% of stars have at least one planetary system, with some estimates as high as 90%. This means that for every 10 stars, 7 of them could potentially have planetary systems orbiting them. This suggests that planetary systems are relatively common in the Universe.
To learn more about current evidence
https://brainly.com/question/29848071
#SPJ1
waves that have traveled out of their area of origin and have become uniform and symmetrical are known as .
The waves that have traveled out of their area of origin and have become uniform and symmetrical are known as spherical waves.
When a wave is generated from a point source, it initially spreads out in all directions as a series of expanding spheres. These waves are called spherical waves because the wavefronts form concentric spheres around the source. As the waves travel further away from the source, they begin to merge and overlap, and the wavefronts become more uniform and symmetrical.
Spherical waves are a fundamental concept in wave physics and are used to describe a wide range of physical phenomena, including sound waves, electromagnetic waves, and water waves. They are particularly useful in situations where the wave source is small and the distance from the source is large compared to the wavelength of the wave.
For more similar questions on waves and wave physics:
brainly.com/question/11820725
#SPJ11
The diffraction limit of a 4-meter telescope is _________ than that of a 2-meter telescope.
a) two times larger
b) four times larger
c) four times smaller
d) two times smaller
e) It depends on the type of telescope.
The diffraction limit of a 4-meter telescope is two times smaller than that of a 2-meter telescope.
The diffraction limit of a telescope is the minimum distance between two objects so that they can still be viewed as separate from one another. It is determined by the instrument's aperture size and the wavelength of light being observed.
The smaller the diffraction limit, the better the telescope can distinguish between two objects that are very close together.
In simpler terms, the diffraction limit refers to the smallest object size that a telescope can observe. This is known as angular resolution, which is determined by the telescope's aperture size and the wavelength of light being observed.
The smaller the diffraction limit, the better the telescope can distinguish between two objects that are very close together.
Therefore, a 4-meter telescope has a smaller diffraction limit than a 2-meter telescope. Hence, the answer is two times smaller.
Learn more about Diffraction limit here:
brainly.com/question/15081792
#SPJ11
find the total horizontal distance traveled by the bullet in 4 seconds using your rounded answer for the horizontal velocity.
The total horizontal distance traveled by the bullet in 4 seconds is: 320 meters.
Using the rounded horizontal velocity of 80 m/s.
To calculate this, we use the equation distance = velocity × time, which would be 80 m/s × 4 s = 320 m.
What is horizontal velocity?Horizontal velocity refers to the component of projectile motion that is horizontal. The horizontal velocity of a projectile is the velocity at which it is moving horizontally. In the absence of air resistance, the horizontal velocity of a projectile remains constant throughout its motion. A horizontal velocity can be positive or negative. It is positive when the projectile is moving to the right and negative when it is moving to the left.
How to calculate total horizontal distance traveled by a bullet?The formula to calculate the total horizontal distance traveled by a bullet in 4 seconds is given below.
Total horizontal distance traveled = (horizontal velocity) × (time taken)
Substitute the value of the horizontal velocity, which is rounded in the question, in the above formula to calculate the total horizontal distance traveled by the bullet. This will give you the required answer.
To know more about "horizontal velocity" refer here:
https://brainly.com/question/18084516#
#SPJ11
calculate suppose an object has a mass of 15 g and a volume of 5 cm^3. what is the density of the object?
An object has a mass of 15 g and a volume of 5 cm³, the density of the object is: 3 g/cm³
To calculate the density of an object with a mass of 15 g and a volume of 5 cm³, you can use the equation
Density = Mass/Volume.
Using this equation, the density of the object is 3 g/cm³.
Density is a measure of how much mass is contained in a given volume of an object. The higher the density, the more mass is contained in the same volume. Mass is measured in grams (g) while volume is measured in cubic centimeters (cm³).
To calculate the density of an object, you must divide the mass of the object (measured in grams) by the volume of the object (measured in cm³).
In this example, the mass of the object is 15 g and the volume of the object is 5 cm³. So, the density of the object is calculated by dividing 15 g by 5 cm³, which gives us a result of 3 g/cm³.
In summary, to calculate the density of an object, you must divide the mass (measured in g) by the volume (measured in cm³). In this example, the mass of the object is 15 g and the volume of the object is 5 cm³, so the density of the object is 3 g/cm³.
To know more about density refer here:
https://brainly.com/question/29775886#
#SPJ11
you push a 15.0 kg box across the floor at a steady speed of 1.25 m/s for 16.0 s. the coefficient of kinetic friction between the box and the floor is 0.680. what is your power output?
The power output of pushing a 15.0 kg box across the floor at a steady speed of 1.25 m/s for 16.0 s, with a coefficient of kinetic friction of 0.680, can be calculated using the formula:
Power = Force x Velocity
Force = mass x acceleration due to friction
Acceleration due to friction = coefficient of kinetic friction x gravitational force
Power = (15.0 kg x 0.680 x 9.8 m/s2) x (1.25 m/s)
Power = 128.4 Watts
Therefore, the power output of pushing the box for 16.0 s is 128.4 Watts.
Imagine sitting on a merry-go-round and riding along as it spins. Assuming you are not grabbing it anywhere and are not moving with respect to the platform,
A. static friction (directed inwards) causes you to accelerate.
B. you are not accelerating because you aren't moving on the platform.
C. static friction (directed outwards) causes you to accelerate.
D. sliding friction makes you accelerate inwards.
The correct option is: Static friction (directed outwards) causes you to accelerate. (Option C)
When you sit on a merry-go-round, you are not moving relative to the platform. Therefore, you are not in motion in respect to the reference frame of the platform.
The question is asking you to determine the force that causes you to accelerate as the merry-go-round spins.
Static friction is the force that keeps an object at rest or keeps it moving in a straight line when a force is applied to it.
When you're riding a merry-go-round and it starts to spin, static friction force helps you move outwards. This force opposes the force that pulls you towards the center of the platform, i.e., centripetal force.
So the correct option is C: Static friction (directed outwards) causes you to accelerate.
To know more about "Static friction" refer here:
https://brainly.com/question/13828735#
#SPJ11
which consumes more energy, a 1.2 kw hair dryer used for 10 min or a 10 w night light left on for 24 hr
A 1.2 kw hair dryer used for 10 min consumes more energy than a 10 w night light left on for 24 hr
To determine which device consumes more energy, you need to calculate the energy consumed by each device. The formula for calculating energy is: Energy = Power x Time
where power is measured in watts (W) and time is measured in hours (h).
Converting 10 minutes into hours, you get: 10 minutes = 10/60 hours = 0.167 hours
Energy consumed by the 1.2 kW hair dryer in 10 minutes: Energy = Power x Time
Energy = 1.2 kW x 0.167 hours
Energy = 0.2 kWh
Therefore, the energy consumed by the 1.2 kW hair dryer in 10 minutes is 0.2 kWh.
Converting 24 hours into minutes, you get: 24 hours = 24 x 60 minutes = 1440 minutes
Energy consumed by the 10 W night light in 24 hours:
Energy = Power x Time
Energy = 10 W x 24 hours
Energy = 240 Wh
Therefore, the energy consumed by the 10 W night light in 24 hours is 240 Wh.
Comparing the two values, we see that 1.2 kW hair dryer used for 10 min consumes more energy than a 10 W night light left on for 24 hours.
To know more about energy, refer here:
https://brainly.com/question/16647#
SPJ11#
11- An object of mass 0.2 kg moves in a circular path. If it makes 3/4 revolution in 0.3 s and its displacement is 6 m, calculate: a) The radius of the circular path ?
We can use the kinematic equations for circular motion to solve this problem. The equation we will use is:
θ = (s / r)
where θ is the angle of rotation (in radians), s is the displacement, and r is the radius of the circular path.
In this case, the object makes 3/4 revolution, which is equivalent to an angle of rotation of:
θ = (3/4) x 2π radians = 1.5π radians
The displacement is given as 6 m.
Therefore, we can rearrange the equation to solve for the radius:r = s / θ
r = 6 m / (1.5π radians)
r ≈ 1.273 m
Therefore, the radius of the circular path is approximately 1.273 meters.
What is a path ?
A path is a route or way that someone or something follows to reach a destination or achieve a particular goal. It can be physical or abstract, and can refer to a variety of contexts such as travel, communication, decision-making, or personal development.
A physical sense, a path can refer to a trail, road, or sidewalk that people use to walk, cycle, or drive to a particular location. In computing, a path refers to the sequence of directories and that lead to a specific file or folder.
To know more about path visit :
https://brainly.com/question/27325244
#SPJ1
Approximately 85% of phosphorus in the body is found in the bones. The other 15% of phosphorus in the body serves mary impertari Durposes. Click to select the functions of phosphorus. Dairy foods are rich sources of calcium, but mary people with lactase intolerance cannot consume these foods without experiending g gestrointestinal discomfort. Fortunately, there are a number of nondairy sources of caiclum. Park the following nondairy foocs in order of calcium content. Most Cakclum Per Sening 1 cup Tohale Rais Bran cereal 1 cup cakcum-fortifed oranon juce 30z salnon with bones From the following food items, click to select the highest source of phosphorus. Click to select the organs that participate in vitamin D synthesis as a result of sunlight exposure.
Functions of phosphorus: Bone formation, ATP production, DNA and RNA synthesis, cell membrane structure.
Order of nondairy foods by calcium content: 1) 1 cup calcium-fortified orange juice, 2) 1 cup Total Raisin Bran cereal, 3) 3 oz salmon with bones.
Highest source of phosphorus: Salmon with bones.
Organs that participate in vitamin D synthesis: Skin (when exposed to sunlight), liver, and kidneys.
What is bone formation?
Bone formation is the process by which bones grow and develop, including the deposition of mineralized bone tissue by osteoblasts and the resorption of bone tissue by osteoclasts, resulting in changes to the shape and structure of bones.
What is RNA?
RNA (Ribonucleic acid) is a molecule that plays a vital role in various biological processes. It is a type of nucleic acid that is composed of a chain of nucleotides, which are the building blocks of the molecule.
RNA is similar to DNA (deoxyribonucleic acid) in terms of its structure, but it has some key differences. RNA is usually single-stranded, while DNA is double-stranded. RNA uses the sugar ribose, while DNA uses deoxyribose. RNA also contains the nitrogenous base uracil, while DNA contains thymine.
To know more about RNA, visit:
https://brainly.com/question/20914096
#SPJ1
in a generator, a force is applied to a loop of wire, which rotates in a magnetic field. what is the primary purpose of this device?
The primary purpose of a generator is to convert mechanical energy into electrical energy. This is achieved through the application of a force to a loop of wire (often called a coil) that is rotating in a magnetic field.
As the coil rotates, it cuts through the magnetic field lines, which induces an electromotive force (EMF) or voltage across the wire. The amount of voltage induced depends on the strength of the magnetic field, the number of turns in the wire coil, and the speed at which the coil is rotated. This induced voltage can be used to power electrical devices, such as lights, motors, and appliances. Generators are used in a variety of applications, including power plants that generate electricity for cities and industries, portable generators for backup power, and small generators for camping and outdoor activities.
Learn more about magnetic field here:
https://brainly.com/question/23096032
#SPJ4
Earthquake _____________ measures shaking at a given location (and so is strongly influenced by _____________) while _____________ is a measurement of the total energy released.Intensity; substrate; magnitude
Earthquake intensity measures shaking at a given location and so is strongly influenced by the substrate, while earthquake magnitude is a measurement of the total energy released.
What is earthquake ?
An earthquake is a natural phenomenon that occurs when the Earth's tectonic plates, which are large pieces of the Earth's crust, move and shift against each other. These movements cause vibrations, or seismic waves, which can be felt on the Earth's surface as shaking or ground motion.
Earthquakes can range in size from small tremors that are barely felt to massive quakes that can cause widespread damage and loss of life. The strength of an earthquake is measured on the Richter scale, which assigns a numerical value to the amplitude of the seismic waves generated by the quake.
Earthquake intensity is a measure of the strength of shaking that is felt at a particular location, and it is influenced by a variety of factors, including the distance from the earthquake epicenter, the local geology and substrate, and the magnitude of the earthquake. Intensity is usually measured on the Modified Mercalli Intensity Scale, which assigns a numerical value to the observed effects of shaking at a given location.
Earthquake magnitude, on the other hand, is a measure of the total amount of energy released by an earthquake, and it is based on the seismic waves that are generated by the earthquake. Magnitude is usually measured on the Richter scale, which assigns a numerical value to the amplitude of the seismic waves as recorded by a seismograph.
In summary, earthquake intensity measures shaking at a particular location and is influenced by the substrate, while earthquake magnitude measures the total energy released by an earthquake and is based on the seismic waves generated by the earthquake.
To know more about earthquake visit :-
https://brainly.com/question/248561
#SPJ1
Which type of light can be broken into its individual wavelengths by a prism? a. infrared b. ultraviolet c. combination d. incandescebt
Although infrared or ultraviolet light is refracted at various angles when it passes through a prism, the resulting spectrum is invisible to the human eye.
Which kind of light can a prism separate into its constituent wavelengths?The white light is broken down into its component colors—red, orange, yellow, green, blue, and violet—as it passes through the prism. The separation of visible light into its many colors is known as dispersion.
Can light be annihilated?The overall amount of energy in the universe cannot be increased or decreased; rather, it only changes from one form to another. The similar process occurs when we burn a candle; wax's chemical energy is transformed into light and heat energy.
To know more about spectrum visit:-
https://brainly.com/question/12157930
#SPJ1
the accumulation of excess electric charge on an object is called....static electricitychargeelectric chargeproton
The accumulation of excess electric charge on an object is called Static electricity.
The excess electric charge remains on the surface of an object until it is discharged, creating a spark or a small electrical shock.
Electric charge is a fundamental property of matter. The total electric charge of a system is the algebraic sum of the charges of its constituents. Electric charge is measured in coulombs (C), which is a unit of electrical charge.
Static electricity is the accumulation of excess electric charge on an object. When two different materials are rubbed together, electrons can be transferred from one material to the other. This transfer of electrons causes one material to become positively charged, while the other becomes negatively charged.
The two materials will then have an electrostatic charge, and the charges will be attracted to each other. Static electricity is responsible for lightning, which is a natural phenomenon. Lightning is caused by the build-up of static electricity in clouds. When the build-up of static electricity is sufficient, it will discharge in the form of a lightning bolt.
For similar question on Static electricity
https://brainly.com/question/821085
#SPJ11
if the average arterial pressure at your heart is a typical 100 mmhg , what is the average arterial pressure in your hands when they are held at your side? assume your hands are 60 cm below your heart.
The average arterial pressure in your hands when they are held at your side is 47.5 mmHg.
The average arterial pressure in your hands when they are held at your side can be determined using the hydrostatic pressure formula, which is a function of height, gravity, and density. When the hands are held at the side, they are 60 cm below the heart, which means they are at a distance of 0.6 m.
The hydrostatic pressure formula is given by
P = ρgh
Where,
P is the pressure, ρ is the density, g is the acceleration due to gravity, and h is the height. We can assume that the density of blood is constant, and we can take the value of g to be 9.81 m/s², the standard acceleration due to gravity.
Therefore, the pressure at the heart is 100 mmHg, or 100/760 = 0.131 atm. The pressure in the hands can be calculated as follows:
P = ρghP = (1.06 × 10³ kg/m³) × (9.81 m/s²) × (0.6 m)
P = 6.26 × 10³ N/m²
P = 6.26 × 10³ Pa
P = 47.5 mmHg
Therefore, the average arterial pressure in the hands when they are held at the side is 47.5 mmHg.
Learn more about hydrostatic pressure at https://brainly.com/question/28206120
#SPJ11
What do the dark lines in an absorption spectrum indicate?
The dark lines in an absorption spectrum indicate that certain frequencies or wavelengths of light have been absorbed by the material that the light has passed through. Absorption occurs when an atom or molecule in the material absorbs a photon of a particular frequency, causing the electron in the atom or molecule to move to a higher energy level.
When white light is passed through a sample of a material, some of the frequencies of light are absorbed by the atoms or molecules in the material, causing dark lines to appear in the spectrum. The positions and intensities of these lines depend on the composition of the material and the conditions under which it is observed.
Absorption spectra are used in a wide range of fields, including astronomy, chemistry, and physics, to identify the composition of materials and study their properties. The dark lines in an absorption spectrum are sometimes called absorption lines or Fraunhofer lines, after the German physicist Joseph von Fraunhofer, who first discovered them in the 19th century.
The dark lines in an absorption spectrum indicate the wavelengths that have been absorbed by the substance.What is an absorption spectrum?An absorption spectrum is a graph that demonstrates the amount of light that is absorbed by a material as a function of wavelength. The graph depicts the amount of light that a sample absorbs at specific wavelengths. An absorption spectrum is created when a source of light is transmitted through a material, and certain wavelengths are absorbed and blocked by the material while others are not. The absorbed wavelengths appear as dark lines, whereas the non-absorbed wavelengths appear as bright lines on the graph. Absorption spectra are used to detect the presence of specific materials, as different substances absorb different wavelengths of light.
For more such questions on Absorption spectrum
https://brainly.com/question/10252035
#SPJ11
pls help 60 pts
screenshot, fill out, then screenshot . attach document to answer using the paperclip button
Answer:
Here you go, hope this helps you pass :)
Explanation:
You're welcome.
what is the log2(100)? it or use a calculator. (to 2 decimal places) round that number up to the next highest integer: based on the tests you've done: what is the maximum number of iterations used for quick search on a collection of 100 items? what is the maximum number of iterations used for linear search on a collections of 100 items? what is the bigo of quick search? hint: n
Log2(100) is 6.64 to 2 decimal places. Rounded up to the next highest integer, it is 7. Based on the tests done, the maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.
The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. The big O of quick search is O(n log n).
log2(100) is the same as x in 2^x=100
This means 2^6.64=100
To solve for 6.64, take the logarithm of both sides.
log(2^6.64)=log(100)
6.64log(2)=log(100)
6.64=2log(10)+2log(5)
log(2)+log(1.25)+log(10)=6.64
log(2)+log(1.25)=6.64-log(10)
log(2)+log(1.25)=2.02
log(2x1.25)=2.02x2^(log(2)+log(1.25))=2.02 x 2^(log(10))=7 (rounded up)
The maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.
The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. In big O notation, the time complexity of linear search is O(n).
To learn more about "log2(100)", visit: https://brainly.com/question/15602305
#SPJ11
In the sketch below, a tractor is pulling a loaded cart at a constant speed. The friction between the cart and the ground is considerable. After the cart has moved a total distance S, the net work done on the cart is ____
A. positive. B. negative. C. zero. D. two of A, B, and C, depending on circumstances. E. three of A, B, and C, depending on circumstances.
The only option that best suits the given condition is Option B, which states that the net work done on the cart is negative.In reality, the frictional force may not exactly balance the force applied by the tractor, and as a result, the net work done on the cart may be negative. Therefore, the correct answer is (B) negative.
The net work done on the cart is negative. The friction between the cart and the ground is significant.What is work?Work refers to the change in energy that occurs when an object is moved from one location to another by a force acting upon it. W = FdCosθ is the formula for calculating work. Where F is the magnitude of the force, d is the displacement of the object, and θ is the angle between the force and the displacement vectors.Since the net work done on the cart is negative, it means that the frictional force is greater than the pulling force, causing the object to slow down. As a result, the work done on the cart is considered negative since it acts in the opposite direction to the direction of motion, according to the definition of work.
for more such questions on frictional force
https://brainly.com/question/24386803
#SPJ11
Two soccer balls (ball A and ball B) are kicked down the field. Ball A is kicked farther than ball B,
but ball B reaches a higher height than ball A. Which of the balls spent more time in the air?
(Come up with your answer and then discuss among your group until there is a consensus.)
Two soccer balls were kicked down the field, Ball A and Ball B. Ball A was kicked farther than Ball B, but Ball B reached a higher height than Ball A. It can be determined that the ball that spent more time in the air was Ball B.
Why Ball B spent more time in the air than Ball A?
Ball B was kicked into the air at a higher angle, meaning it travelled upwards for a longer amount of time. The ball's horizontal velocity would have been lower than Ball A's, causing it to travel a shorter distance horizontally.
However, the additional time Ball B spent travelling upwards and falling back down would have compensated for the shorter horizontal distance travelled, allowing it to remain in the air for longer than Ball A.
Ball A's flight time would have been shorter than Ball B's flight time because of its high horizontal velocity. Because Ball B had a higher initial upward velocity, it travelled higher in the air and took longer to fall back down, resulting in a longer flight time. As a result, Ball B spent more time in the air than Ball A.
To know more about horizontal velocity:
https://brainly.com/question/18084516
#SPJ11
A bus engine transfers chemical potential energy into ___ so that the bus moves.
a. kinetic energy
b. thermal energy
c. gravitational potential energy
d. electrical energy
If the magnetic field steadily decreases from B to zero during a time interval t , what is the magnitude E of the induced emf?
Express your answer in terms of x,y ,t , and B .
If the magnetic field steadily decreases from B to zero during a time interval t, the magnitude E of the induced emf is given by the formula; E = (Bx-y/t), where B is the magnetic field, x, and y are constants.
An induced emf is the voltage generated across a conductor when it moves through a magnetic field. It is also induced when there is a change in the magnetic field passing through a conductor.
The emf generated in a coil of wire is equal to the rate of change of magnetic flux through the coil. Magnetic flux is given by the formula: φ=B*A,
where - B is the magnetic field strength and
- A is the area of the coil.
If the magnetic field steadily decreases from B to zero during a time interval t, the change in magnetic flux is given by the formula: Δφ=B*A = B*ΔA, where ΔA is the change in area over time Δt.
The induced emf E is given by the formula: E = (-N * Δφ)/Δt
Where N is the number of turns in the coil. If the magnetic field is steadily decreasing, then ΔB/Δt is constant, and the induced emf E is given by the formula: E = (-N * B * ΔA/Δt) = (-N * B * x*y/t) = (Bx-y/t), where x and y are constants.
Learn more about magnetic fields here:
https://brainly.com/question/26257705
#SPJ11
what bias has been applied to a pn junction if the cathode is positive with respect to the anode?
A forward biased has been applied to a P-N junction if the cathode is positive with respect to the anode.
A P-N junction is a type of semiconductor junction formed by joining together two types of semiconductors - P-type and N-type. P-type semiconductors have an excess of positively charged holes, while N-type semiconductors have an excess of negatively charged electrons.
When these two types of semiconductors are brought into contact, the electrons from the N-type material flow into the P-type material, filling some of the holes and creating a region with a net negative charge (the N-side), while the P-type material loses some of its holes and creates a region with a net positive charge (the P-side). This creates a potential difference between the P and N regions, which can be used to generate a current. P-N junctions are essential components in electronic devices such as diodes, transistors, and solar cells.
To learn more about P-N junction visit here:
brainly.com/question/13507783
#SPJ4
what is the net torque when you are holding a 10 lb weight 1 ft from your elbow (producing a clockwise torque) and your biceps is generating a 40 lb force with a moment arm of 6 in. (producing a counterclockwise torque)?
The net torque when you are holding a 10 lb weight 1 ft from your elbow (producing a clockwise torque) and your biceps are generating a 40 lb force with a moment arm of 6 in (producing a counterclockwise torque) can be calculated using the formula below:τ = r x F where τ is the torque, r is the moment arm, and F is the force. In this scenario, the clockwise torque produced by the weight is τ1 = (-1 ft) x (10 lb) = -10 lb-ft (negative because it is clockwise), and the counterclockwise torque produced by the biceps is τ2 = (0.5 ft) x (40 lb) = 20 lb-ft (positive because it is counterclockwise).To find the net torque, we must add the two torques together:
τnet = τ1 + τ2τnet = (-10 lb-ft) + (20 lb-ft)
τnet = 10 lb-ft
Therefore, the net torque is 10 lb-ft.
For more information regarding this topic, you can check the below link
https://brainly.com/question/30338152
#SPJ11
Suppose two protostars form at the same time, one with a mass of 0.5 msun and the other with a mass of 15 msun . Which of the following statements are true?
[Select ALL answers that are true in alphabetical order]
A) The 10MSun protostar will have a smaller change in surface temperature during this phase than the 0.5MSun protostar.
B) The 10MSun protostar will reach the main sequence cooler and fainter than the 0.5MSun protostar.
C) The 10MSun star will end its main-sequence life before the 0.5MSun star even completes its protostar stage.
D) The 10MSun protostar will have a smaller change in luminosity during the sequence shown than the 0.5MSun protostar.
E) The 10MSun protostar will be much more luminous than the 0.5MSun protostar.
The two protostars form at the same time, the 10MSun star will end its main-sequence life before the 0.5MSun star even completes its protostar stage, and 10MSun will be much more luminous than the 0.5MSun protostar. Thus, options C and E are correct.
More massive stars have shorter lifetimes because they burn through their nuclear fuel more quickly.
Therefore, the 10MSun star will end its main-sequence life before the 0.5MSun star even completes its protostar stage. Thus, option C is correct.
The luminosity of a star depends on its mass.
More massive stars have higher luminosities than less massive stars. Therefore, option E is correct.
Thus, options C and E are correct.
Learn more about protostars here:
https://brainly.com/question/7849717
#SPJ11
In an elastic collision, bumper cars 1 and 2 are moving in the same direction when bumper car 1 rear-ends bumper car 2. The initial speed of bumper car 1 is 6.71 m/s and that of bumper car 2 is 4.93 m/s. The bumper cars have the same mass. Take the positive direction to be the direction in which the bumper cars are moving.
What is the final velocity, in meters per second, of bumper car 1?
What is the final velocity, in meters per second, of bumper car 2?
The final velocities of bumper car 1 is 6.17 m/s, and the final velocity of bumper car 2 is 5.47 m/s.
What is the final velocity?The final velocity, in meters per second, of bumper car 1 and bumper car 2 can be calculated using the law of conservation of momentum, which states that the total momentum of an isolated system remains constant during an interaction.
Since the collision is elastic, the kinetic energy is also conserved. Here's how to calculate the final velocity of bumper car 1 and bumper car 2:
Initial velocity of bumper car 1, u₁ = 6.71 m/s
Initial velocity of bumper car 2, u₂ = 4.93 m/s
Final velocity of bumper car 1, v₁ = ?
Final velocity of bumper car 2, v₂ = ?
Since the bumper cars have the same mass, m₁ = m₂ = m (say)
According to the law of conservation of momentum,
m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂
Let's substitute the values:
mu₁ + mu₂ = mv₁ + mv₂
(m₁ + m₂)u₁ = m₁v₁ + m₂v₂
Now, substitute the mass and velocity values:
m × 6.71 + m × 4.93 = m × v₁ + m × v₂
Simplifying the above equation, we get:
v₁ + v₂ = 11.64 ...(1)
Similarly, using the law of conservation of kinetic energy, the final velocities can be determined. It is given by,
m₁u₁² + m₂u₂² = m₁v₁² + m₂v₂²
Substituting the values, we get:
m × 6.71² + m × 4.93² = m × v₁² + m × v₂²
Simplifying the above equation, we get:
v₁² + v₂² = 62.98 ...(2)
From equations (1) and (2), we can solve for v₁ and v₂ by elimination method as follows:
v₁ + v₂ = 11.64 ...(1)
v₁² + v₂² = 62.98 ...(2)
Multiplying equation (1) by v₁ and subtracting it from equation (2), we get:
v₁² + v₂² - v₁² - v₁v₂ = 62.98 - 11.64
v₁v₂ = 51.34 ...(3)
Again, subtracting equation (1) from equation (2), we get:
v₁² + v₂² - v₁² - 2v₁v₂ - v₂² = 62.98 - 11.64
v₁v₂ = 25.07 ...(4)
Now, solving equations (3) and (4), we get:
v₁ = 6.17 m/s, v₂ = 5.47 m/s
Therefore, the final velocity of bumper car 1 is 6.17 m/s, and the final velocity of bumper car 2 is 5.47 m/s.
Learn more about Velocity here:
brainly.com/question/30559316
#SPJ11
Hooke's law: Consider a plot of the displacement (x) as a function of the applied force (F) for an ideal elastic spring. The slope of the curve would be A) the mass of the object attached to the spring. B) the reciprocal of the acceleration of gravity. C) the spring constant. D) the acceleration due to gravity. E) the reciprocal of the spring constant.
Hooke's law: the slope of the curve would be the spring constant (C).
What is Hooke's law?Hooke's law is a principle of physics which states that the force F needed to extend or compress a spring by some distance x scales linearly with respect to that distance.
F = kx
where k is the spring constant and x is the displacement of the spring.
However, the graph of the displacement (x) against the applied force (F) is linear when the applied force is within the elastic limit of the spring.
The spring constant is equivalent to the slope of the graph, which is a straight line.
Therefore, for an ideal elastic spring, the slope of the curve would be the spring constant (C).
To know more about Hooke's law:
https://brainly.com/question/13348278
#SPJ11
Materials that allow electricity to flow are called A) Insulators B) Conductors C) Electron flows D) Stimulators
B) Conductors, Materials known as conductors allow electricity to pass through them with little or no resistance. Metals like aluminum, silver, and copper are among the examples.
Materials known as conductors have a low resistance to electricity passing through them. They are able to move freely through the material because they have free electrons that are not strongly bonded to the atomic nucleus. Due to their abundance of free electrons, metals like copper, aluminium, silver, and gold are the most popular conductors. A material's conductivity—expressed as electrical conductivity or its opposite, resistivity—determines its capacity to carry electricity. Electrical wires, power transmission lines, electronic components, and circuit boards are just a few of the many uses for conductors. They also have a variety of industrial uses and are found in medical equipment like pacemakers and EEG machines.
learn more about conductors here:
https://brainly.com/question/30047010
#SPJ4
how do net torque and rotational inertia affect the angular acceleration of a rotating object? experimentally determine the mathematical relationship between net torque, rotational inertia, and angular acceleration of a rotating object
Net torque and rotational inertia are related to the angular acceleration of a rotating object.
In general, the angular acceleration of a rotating object is directly proportional to the net torque applied to the object and inversely proportional to the object's rotational inertia.
Mathematically, this can be represented as:
α = τ / I
Where
α is the angular acceleration of the object,
τ is the net torque applied to the object, and
I is the object's rotational inertia.
The net torque is the total torque acting on an object, and it is the difference between the clockwise and anticlockwise torques. The rotational inertia of an object is the measure of an object's resistance to rotational motion.When the net torque acting on an object is zero, the angular acceleration of the object is also zero. This is because the torque and angular acceleration have a linear relationship. The greater the torque applied to an object, the greater the angular acceleration of the object.
In conclusion, the net torque and rotational inertia affect the angular acceleration of a rotating object, and the mathematical relationship between them can be experimentally determined using the formula α = τ / I.
Learn more about torque here: https://brainly.com/question/29385853
#SPJ11