Answer:60mph means it runs every minute.
Explanation: because it makes sense.
Answer:
2640 ft, or 1/2 mile
Explanation:
Recognizing that 30 s = 0.5 min, we can convert the units like this.
distance = speed × time
distance = (60 mi/h) × (1 h/(60 min)) ×(0.5 min) = 0.5 mi
In feet, that is ...
(5280 ft/mi)(0.5 mi) = 2640 ft
A cheetah runs 1/2 mile, or 2640 feet in 30 s.
Student 1 lifts a box with a force of 500 N and sets it on a tabletop 1. 2 m high. Student 2 pushes an identical box up a 5 m ramp from the floor to the top of the same table. Which student did the MOST work?.
The student 2 did the MOST work because he pushed the box to a greater height.
The given parameters:
Force applied by Student 1 = 500 NHeight of table for student 1 = 1.2 mHeight of ramp for student 2 = 5 mThe work done by student 1 is calculated as follows;
Work = P.E = mgh
P.E = 1.2mg
The work done by the student 2 is calculated as;
P.E = 5mg
where;
m is the mass of the boxThus, we can conclude that the student 2 did the MOST work.
Learn more about work done here: https://brainly.com/question/8119756
train travels 1/4of its total distance over half of its time with a constant velocity of 5m/s. calculate the average velocity
Let D be the total distance (say in meters) traveled by the train and T the time (say in seconds) it takes to do so. (Assume the train moves in a straight line in only one direction.) Then the average velocity of the train as it covers this distance is
v (ave) = D/T
We're told the train can traverse a distance of D/4 in a matter of T/2 seconds if it moves at a speed of 5 m/s. This means
D/4 = (5 m/s) (T/2)
⇒ 5 m/s = 1/2 D/T
⇒ v (ave) = D/T = 10 m/s
What will happen if the two plungers are pressed together firmly? Explain your answer.
Answer:
This air being forced out causing the air pressure inside to be much lower than that on the outside. As higher air pressure always pushes, it keeps the two plungers together.
Hope that helps. x
When the mass of the cylinder increased from 3. 0 kg to 6. 0 kg, what happened to the amount of heat generated in the system? It decreased by a factor of 3. It decreased by a factor of 2. It increased by a factor of 2. It increased by a factor of 3.
When the mass of the cylinder increases from 3. 0 kg to 6. 0 kg, the amount of heat generated in the system increases by a factor of 2.
The given parameters:
Initial mass of the cylinder, m₁ = 3.0 kgFinal mass of the cylinder, m₂ = 6.0 kgThe amount of heat generated in the system is calculated as follows;
Q = mcΔT
where;
m is the massc is the specific heat capacityΔT is the change in temperatureIf we keep every other parameters constant and change the mass from 3.0 kg to 6.0 kg, the increase in the heat generated is calculated as follows;
[tex]Q_1 = 3c \Delta T\\\\Q_2 = 6c\Delta T\\\\Q_2 = 2(3c \Delta T)\\\\Q_2 = 2Q_1[/tex]
Thus, when the mass of the cylinder increases from 3. 0 kg to 6. 0 kg, the amount of heat generated in the system increases by a factor of 2.
Learn more about heat capacity here: https://brainly.com/question/16559442
Which is a possible food chain in the ocean from start to finish?
a.phytoplankton, zooplankton, small fish, large fish, large shark
b.phytoplankton, large shark, zooplankton, large fish, small fish
c.large shark, large fish, small fish, zooplankton, phytoplankton
d.zooplankton, phytoplankton, large fish, small fish, large shark
Answer:
a.phytoplankton, zooplankton, small fish, large fish, large shark
Explanation:
The bottom level of the ocean's food chain is made up of one-celled organisms called phytoplankton. These tiny organisms are microscopic. They are so small they cannot be seen without a microscope. Billions of phytoplankton live in the upper part of the ocean. They take in the sun's light.
Phytoplankton, or plant plankton, is the first link in the food chain in the ocean. They require sunlight for photosynthesis, which they must perform. They therefore reside higher up in the shallow sunlight. Furthermore, they transform themselves into an ocean animal that can eat the “food” from the sun. Thus, option A is correct.
What food chain in the ocean from start to finish?One-celled organisms known as phytoplankton make up the base of the ocean's food chain. These microscopic organisms are quite small. Without a microscope, they are invisible due to their small size. In the upper ocean, there are billions of phytoplanktons. They absorb the light from the sun.
Aquatic food webs are built on phytoplankton and algae. They are consumed by zooplankton, tiny fish, and crustaceans, which are the main consumers. Fish, tiny sharks, corals, and baleen whales all devour the primary consumers after them.
Therefore, phytoplankton, zooplankton, small fish, large fish, large shark is a possible food chain in the ocean from start to finish.
Learn more about ocean here:
https://brainly.com/question/29360503
#SPJ2
how is the thermal efficiency of a heat engine defined?
The distance-time graph for a vehicle standing on a road side will be
Answer:
hi
Explanation:
could you please upload ur image
nitrogen dioxide is a major component of smog which type of chemical reaction creates this product?
a. synthesis reaction
b. replacement reactions
c. combustion reactions
d. decomposition reaction
Answer:
A.synrhesis reaction
#carryonlearning
If the forces acting on an object at rest are ______,the object will remain at rest.
Answer:
friction. or gravity both ofbthem .....................
..
[tex] \huge{ \mathrm{question \hookleftarrow}}[/tex]
Calculate equivalent resistance of two resistors R1 and R2 in parallel where,
[tex] \sf R_ 1 = (6 \pm0.2 )\: \: ohms[/tex]
[tex] \sf R_ 2 = (3 \pm0.1 )\: \: ohms[/tex]
[tex]it \: was \: helpful \: to \: you[/tex]
# be careful#
How is the independent variable affected by the dependent variable
Answer:
A dependent variable is a variable that is tested in an experiment. An independent variable is that can be modified. Depending on what you are testing, the dependent variable will change accordingly to the dependent variable.
- I'm reading this back and it doesn't make much sense, if you want me to reword this I can
Is it raining anywhere else because it is about to start pouring where I live
Current Forecast is:
Sunny with a temp of 67 deg F, as of rn there is no clouds in the sky
Location, Oklahoma USA in the NE corner
how to calculate kinetic energy given mass and velocity
In classical mechanics, kinetic energy (KE) is equal to half of an object's mass (1/2*m) multiplied by the velocity squared. For example, if a an object with a mass of 10 kg (m = 10 kg) is moving at a velocity of 5 meters per second (v = 5 m/s), the kinetic energy is equal to 125 Joules, or (1/2 * 10 kg) * 5 m/s2.
4 What type of circuit is described by each of the following statements?
Answer series or parallel
a All components are connected end-to-end.
b. The current in the circuit divides so that some flows through one component
and the rest through another component
Two lamps are connected side by side so that each lights brightly
d The current has the same valur everywhere in the circuit
C
What is the difference between folk dance and ballroom dance
Answer:
folk dancing is old music and ball room is young dancing
Given that 1 pound is equal to 4.45 newton’s what is the weight of a 500N child in pounds?
Answer:
112.36 pounds
Explanation:
Since 1 pound = 4.45 Newtons, a 500N child in pounds = 500÷4.45 = 112.36 pounds (approximately).
What is the monthly cost of using a 750 W refrigerator that runs for 8 hours every day, if the cost per kWh is $0.23?
Answer:
Assuming there are 28 days in each month,
750W = 0.75kW
Cost of electric bill = 0.75 × 8 × 28 × $0.23
= $38.64
how to determine my slope in physics graph
Answer:
Determine the coordinates of two points on the line. Calculate the difference between these two locations' y-coordinates (rise). Calculate the x-coordinate difference between these two places (run). Divide the y-coordinate difference by the x-coordinate difference (rise/run or slope).
Two gravitational forces act on a
given object. How do you determine the total gravita-
tional force acting on the object?
Answer:
Explanation:
Depends on the location of the two forces. If they are aligned on the same side of the object, you would simply add.
X -----------F1 -------F2
X is the object. F1 and F2 are both masses which create a gravitational force. They both are the form of Fx = G * m1 * m2 / r^2. The total force is F1 + F2
If they are are on either side of the object, you subtract.
F1 ---------X ---------F2
Fx = F1 - F2
Any other location of F1 and F2 is much more complicated by the use of trigonometry.
Help plz I don’t know it
Answer:
2. thermal insulator. 3. convection current. 4. conduction. 5. thermal conductor. 6. radiation.
Explanation:hope this helps you.
Which of the balls will exert the smallest force on object A?Why
One ball of mass 0.600kg travelling 9.00m/s to the right collides head on elastically with a second ball of mass 0.300kg travelling 8.00m/s to the left.what are their velocities after collisions?
Let m₁ and v₁ denote the mass and initial velocity of the first ball, and m₂ and v₂ the same quantities for the second ball. Momentum is conserved throughout the collision, so
m₁ v₁ + m₂ v₂ = m₁ v₁' + m₂ v₂'
where v₁' and v₂' are the balls' respective velocities after the collision.
Kinetic energy is also conserved, so
1/2 m₁ v₁² + 1/2 m₂ v₂² = 1/2 m₁ (v₁')² + 1/2 m₂ (v₂')²
or
m₁ v₁² + m₂ v₂² = m₁ (v₁')² + m₂ (v₂')²
From the momentum equation, we have
(0.600 kg) (9.00 m/s) + (0.300 kg) (-8.00 m/s) = (0.600 kg) v₁' + (0.300 kg) v₂'
which simplifies to
10.0 m/s = 2 v₁' + v₂'
so that
v₂' = 10.0 m/s - 2 v₁'
From the energy equation, we have
(0.600 kg) (9.00 m/s)² + (0.300 kg) (-8.00 m/s)² = (0.600 kg) (v₁')² + (0.300 kg) (v₂')²
which simplifies to
67.8 J = (0.600 kg) (v₁')² + (0.300 kg) (v₂')²
or
226 m²/s² = 2 (v₁')² + (v₂')²
Substituting v₂' yields
226 m²/s² = 2 (v₁')² + (10.0 m/s - 2 v₁')²
which simplifies to
3 (v₁')² - (20.0 m/s) v₁' - 63.0 m²/s² = 0
Solving for v₁' using the quadratic formula gives two solutions,
v₁' ≈ -2.33 m/s or v₁' = 9.00 m/s
but the second solution corresponds to the initial conditions, so we omit that one.
Then the second ball has velocity
v₂' = 10.0 m/s - 2 (-2.33 m/s)
v₂' ≈ 14.7 m/s
When dribbling a ball, the ______________ should control the direction and downward motion of the ball.
Answer:
gravity
Explanation:
keeps the ball down on the surface
When dribbling a ball, the gravity should control the direction and downward motion of the ball.
What is projectile motion?When a particle is hurled obliquely near the surface of the earth, it travels along a curved path while accelerating continuously in the direction of the planet's centre (we assume the particle stays close to the surface of the globe). Such a particle's motion is known as projectile motion, and its route is referred to as a projectile.
Two distinct rectilinear motions occur simultaneously in a projectile motion:
Uniform velocity along the x-axis is what causes the particle to move horizontally (ahead).Uniform acceleration along the y-axis is what causes the particle to move vertically (downwards).When a ball is sent into the air at a certain speed, the only force acting on it is the acceleration caused by gravity (g).
Learn more about projectile motion here:
https://brainly.com/question/11049671
#SPJ2
can you fit all the planets between earth and moon
Answer: No, planets of our solar system, with or without Pluto, cannot fit within the mean lunar distance. An additional 3,500 km is needed to squeeze in Neptune
Which statement accurately describes how the acceleration of an object in free fall changes?
O A. It accelerates downward at a constant rate.
O
B. It accelerates downward at an increasing rate.
C. It accelerates downward at an irregular rate.
D. It accelerates downward at a decreasing rate.
Answer: A
Explanation: An object in free fall only is affected by gravity, so the acceleration is 9.8 m/s²
Please help me answer this! ANSWER IN SCENTENCE FORMAT!!! :
Two factors that affect climate patterns on Earth are the tilt of Earth on its axis and the topography of Earth. Describe how these two factors affect the climate patterns of Earth.
Answer:
If you are saying How much does the tilt of the Earth affect the climate
This varies between a tilt of 22.1 and 24.5 degrees over a period of about 41,000 years. This trend not only affects the average temperature of the earth, but also how prominent the seasons are. Procession is a wobble in the earth's axis.
why we use light-years in space verses other units of distance?
Answer:
The light year is used to measure distances in space because the distances are so big that a large unit of distance is required.
> what are the four states of matter? how are they defined?
Answer:
In physics, a state of matter is one of the distinct forms in which matter can exist. Four states of matter are observable in everyday life: solid, liquid, gas, and plasma.
...
To From Gas
Solid Deposition
Liquid Condensation
Plasma Ionization
Pravat exerts a force of 30 N to lift a bag of groceries 0. 5 m. How much work did Pravat do on the bag? Note : Work = Force x Distance 0 J 15 J 30 J 60 J.
Answer:
15 JExplanation:
The work done by an object can be found by using the formula
workdone = force × distance
From the question we have
workdone = 30 × 0.5 = 15
We have the final answer as
15 JHope this helps you
The amount of work done by Pravat if he exerts a force of 30 N to lift a bag of groceries 0.5m is 15J.
WORK DONE:The work done by a body can be calculated by multiplying the force exerted by the distance moved. That is;
Work done = force (F) × distance (m)
According to this question, Pravat exerts a force of 30N to lift a bag of groceries 0.5 m. The work done is calculated as follows:
Work done = 30N × 0.5m
Work done = 15J
Therefore, the amount of work done by Pravat if he exerts a force of 30 N to lift a bag of groceries 0.5m is 15J.
Learn more about work done at: https://brainly.com/question/8119756?referrer=searchResults
A bus accelerates away from the bus stop at 2.5 m/s2
.
The total mass of the bus and passengers is 14 000 kg.
Calculate the resultant force needed to accelerate the bus and passengers.
help pls my brain is not working
Explanation:
F=k.g m\s2
=2.5 m\s2 14000k.g
= 35000N