a car weighs 3600 kg is traveling at 21.0 m/s. the driver doesn?t notice a red light and rear-ends another car at rest. both cars stick together and move with a speed of 9.0 m/s. what is the mass of the car that was at rest?

The time it takes for the ball to reach its maximum height is 745 milliseconds.

What is time?

Time is defined as a scalar quantity that describes the progression of events in the universe. It is often considered to be the fourth dimension of spacetime, along with the three dimensions of space. Time is closely related to the concepts of causality, or the relationship between cause and effect, and is considered to be a fundamental aspect of the physical universe.

To find the time it takes for the ball to reach its maximum height, we need to use the equation:

1/2 * a * t^2 + v * t + d = 0

where a is the acceleration due to gravity (-9.8 m/s^2), t is the time, v is the initial velocity (2.13 m/s), and d is the initial displacement (0 m, since the ball is thrown upward from the ground).

We know that the ball is thrown upward and reaches its maximum height, so it is subject to a constant acceleration due to gravity in the downward direction. Therefore, the acceleration is -9.8 m/s^2.

The time to reach the maximum height can be found by solving the above equation for t.

t = sqrt(-2*d/(a+v))

t = sqrt(-2*0/(-9.8+2.13))

t = sqrt(2*2.13/(9.8-2.13))

t = sqrt(4.26/7.67)

t = sqrt(0.555)

t = 0.745s

To get the time in milliseconds:

t = 0.745s * 1000ms/s = 745 ms

Therefore, the time it takes for the ball to reach its maximum height is 745 milliseconds.

To learn more about time from the given link:

https://brainly.com/question/26046491

#SPJ4

(a) The potential energy of the system to the conservative force acting on the particle, with Ui=0:

(b) From (a), U(2.00m)=2A–2.67B, and U(3.00m)=4.5A–9B.

ΔU=(4.5A−9B)−(2A−2.67B)=2.5A−6.33B

(c) For the entire system of which this particle is a member, this work is internal work and equal to the negative of the change in potential energy of the system: ΔK=−ΔU=−2.5A+6.33B.

To learn more about kinetic energy refer to:

https://brainly.com/question/8101588

#SPJ4

The value of T when a particle is at rest is 0. The velocity of the particle at t=0 is zero because the particle is in rest position and did not moving at any of the instance or travelling at an uniform speed through out the whole journey or yet did not start from the source point.

Velocity is the rate of change of velocity. At any point on a trajectory, the magnitude of the velocity is given by the rate of change of velocity in both magnitude and direction. Velocity of the body that we can consider is the increasing value of the velocity of any object at a constant rate and that of we can calculate. Hence by the primary information that we have we can formerly consider that the velocity which is acting on the particle at t=0 is zero because the particle is in rest position and did not moving at any of the instance or travelling at an uniform speed through out the whole journey or yet did not start from the source point and the value of T when a particle is at rest is zero.

Learn more about Velocity:

brainly.com/question/18084516

#SPJ4

  The correct definition of minerals is 'nutrients that strengthen bones and teeth, help keep the blood healthy, and keep the heart and other organs working properly'

 Minerals and vitamins are essential micronutrients that the body uses to carry out its normal functions. Minerals can be obtained from foods (or artificially), these micronutrients have fundamental roles in growth, fluid balance, bone health, and different physiological processes.  Some of the most important minerals include calcium, iron, phosphorous, fluoride, selenium, sodium, copper, iodine, and zinc.

It states that the force F acting on a body is equal to the mass m of the body multiplied by the acceleration an of its center of mass, or F = ma.

The fundamental equation of motion in classical mechanics is F = ma.

Since gravity affects an object's vertical motion, while it moves, it is said to be in motion under gravity.

The force that pushes objects downward is called gravity. In reality, gravity draws things toward the centre of the Earth. Homogeneous acceleration is experienced by a body in free fall.

Motion. It is said that the body is moving at an accelerated rate. Therefore, if a body falls freely while being affected by gravity, its velocity will begin to increase at a rate of 9.8 m/s2.

When a body falls freely under the effect of gravity alone in a vacuum, potential energy continuously decreases and kinetic energy continuously increases; as a result, the conservative force acts on the body.

To learn more about motion of body refer to:

brainly.com/question/1157001

#SPJ4

This statement is True, the angular diameter of an object is inversely proportional to its distance from the observer.

Angular diameter is a measure of the apparent size of an object in the sky as seen from a given location. It is the angular distance between two opposite points on the visible surface of the object, usually measured in degrees or arcminutes. Angular diameter can be used to describe the apparent size of both small and large objects, such as planets, stars, galaxies, and clusters.

For example, the angular diameter of the Sun as seen from Earth is approximately 0.5 degrees, while the angular diameter of the Moon is approximately 0.5 degrees. Angular diameter can also be used to measure the apparent size of large-scale structures in the Universe, such as the distance between two galaxies in a galaxy cluster. The angular diameter of a galaxy cluster is typically measured in arcminutes or arcseconds. Angular diameter is a useful measure of the size of an object since it is independent of the distance between the observer and the object.

To learn more about Angular diameter visit here:

brainly.com/question/21776288

#SPJ4

On prevent the puppies from tearing down the board, Ginger must apply 32 N of force to the opposite side.

The total force acting on the system is equal to the acceleration of the center of mass times the system's total mass. When applied to an extended object, Newton's second law, F = ma, predicts the motion of a specific reference point for this object.

The vector sum of all forces acting on an object is known as the net force. In other words, the net force is the sum of all the forces, taking into mind that a force is a vector and that two forces that have the same magnitude but facing the opposite direction will cancel each other out.

To learn more about force visit:

brainly.com/question/13191643

#SPJ4

The distance between the force's line of action and the center of moments, also known as the moment arm or lever arm, is perpendicular. Force times distance equals moment.

A force's moment is determined by its magnitude and distance from the rotational axis. The strength of a force is measured by its moment around a point (the perpendicular distance of the line of action of the force from the point).

The distance from an axis to the line of action of a force is known as the moment arm (or lever arm) of a force system. In other words, the moment arm controls the torque's quality.

To know more about moment arm visit:-

https://brainly.com/question/14212503

#SPJ4

Answer:

A. The average kinetic energy decreased.

Explanation:

When an object gains heat, which is a form of energy, the atoms within the object would in turn gain energy in the form of kinetic energy. Similarly, as the temperature of an object decreases, in other words losing heat energy, the atoms within the object would lose kinetic energy as a result.

Thermal energy increases during melting.

When ice melts during melting, its temperature remains constant until all the ice turns into water. Then, heating of liquid water causes the molecules to vibrate faster and steadily increasing the temperature.

Thermal energy refers to the energy contained within a system that is responsible for its temperature. Heat is the flow of thermal energy. A branch of physics, thermodynamics, concerns with how heat is transferred among different systems.

An example of thermal energy is boiling water on a stove. When boiling water, thermal energy is produced when the atoms and molecules in a substance vibrate faster because of raising in temperature.

Learn more about thermal energy at: https://brainly.com/question/18989562

#SPJ4

Hormones are substances that communicate with your organs, skin, muscles, and other tissues through your blood to coordinate various bodily functions.

It serves as a sensory organ (touch, temperature detection), aids in temperature control, protects against mechanical, thermal, and physical injury as well as hazardous substances, prevents moisture loss, reduces the harmful effects of UV radiation, has an immune system that can detect diseases, etc.

The six primary functions of the skin are: protection, absorption, excretion, secretion, regulation, and sensation.

Our first line of defence against harmful chemicals, radiation, and poisons is our skin.

The outside world is kept at bay by a skin barrier. is the first line of defence against potentially harmful microbes.

To learn more about the main functions of the skin refer to:

brainly.com/question/306377

#SPJ4

Platform moves towards to west with a speed of v0/2 when the dog moves towards to east at a speed of v0, in accordance with the rule of conservation of momentum.

The speed at which an object's location changes in any direction. The distance travelled to the time needed to travel that distance is known as speed. Since speed only has a magnitude and no direction, it is a scalar quantity.

Acceleration is the method of changing a speed with which an object moves. If a substance's velocity does not change, it is not accelerating. Acceleration is a vector quantity.

To know more about Speed visit :

brainly.com/question/28224010

#SPJ4

A fish under water appears to be at a different depth than it actually is due to the refraction of light as it passes through the water.

When light travels through a medium with a different index of refraction, such as air to water, it bends, or refracts. This causes objects to appear displaced, or closer or farther away than they actually are. Because water has a higher refractive index than air, light bends more when it enters the water, causing objects, like fish, to appear closer to the surface than they actually are.

The result is that the fish will appear to be deeper in the water than it actually is.

To learn more about Refraction,

https://brainly.com/question/14760207

https://brainly.com/question/29734230

The acceleration due to gravity at the surface of Neptune is calculated to be 10.08 m/s².

Here, we can apply the concept of Newton for the definition of the gravity of a planet, for which he defines that this is proportional to the product of the mass of the planet by the universal gravitational constant, and inversely proportional to the square of the radius of the planet. Mathematically this can be described as

g = GM/r²

where,

G is universal gravitational constant

M is the mass of the planet

r is the radius of the planet

Given that,

Mass of the planet M = 1.025 × 10²⁶ kg

Diameter of the planet = 49532 km = 49532 × 10³ m

Radius of the planet = 24766 × 10³ m

After putting the values into the equation above, we have,

g = GM/r² = (6× 10⁻¹¹) (1.025 × 10²⁶)/(24.7 × 10⁶)² = (6.15 × 10¹⁵)/(24.7 × 10⁶)² = 10.08 m/s²

To know more about acceleration due to gravity:

https://brainly.com/question/14419196

#SPJ4

The angle (in degrees) of the water surface with the horizontal is 14.3 degrees

The angle of the water surface with the horizontal can be determined using the concept of the accelerations of gravity and centripetal force. The acceleration of gravity acts in the downward direction, and the centripetal force acts in the opposite direction of the acceleration. In this case, the horizontal acceleration of the tank is 2.45 m/s^2, which acts in the opposite direction of the gravitational acceleration.

The angle of the water surface with the horizontal can be found by taking the tangent of the ratio of the centripetal acceleration to the gravitational acceleration.

tan(theta) = (centripetal acceleration) / (gravitational acceleration)

tan(theta) = (2.45 m/s^2) / (9.8 m/s^2) = 0.25

Theta = 14.3 degrees

So the angle of the water surface with the horizontal is 14.3 degrees.

Learn more about fluid dynamics and motion here: https://brainly.com/question/4629227

#SPJ4

It would take approximately 0.45 seconds for a 17 m tall building to hit the ground.

What is distance?

Distance is the amount of space between two objects or points. It is measured in units such as meters, feet, or miles. Distance can also refer to the length of time it takes for something to happen, such as the distance between two events.

This is calculated by using the formula: time = (distance)/(gravity x 2). In this case, distance is 17m and gravity is 9.8 m/s2, so time = (17 m)/(9.8 m/s2 x 2) = 0.45 seconds.
Distance may also refer to the emotional or physical separation between two people or groups. Distance can be expressed as a physical, mental, or emotional concept.

To learn about more distance.

brainly.com/question/26550516

#SPJ1

The 2.00-kilogram object weighs 19.6 newtons on Earth, its weight on the Mars is 2.00 kg.

The mass is known as the amount of matter which is contained in a body.  It is a property which is consistent in a body regardless of the body's current location, gravitational pull and various other factors which exist.

Mass and weight are two separate quantities. Weight is computed as a product of mass and acceleration. Mass has a property to remain constant and it means that whether the object is on any planet, irrespective of that, it will be constant. The mass remains the same that is 2.00 kg.

Learn more about mass:

brainly.com/question/13040516

#SPJ4

The force required to raise the box up the ramp when the ramp is 12 meters long, the box is 4 meters and the box weighs 200 newtons is 653.33 N (7840/12)

To determine the force required to raise the box up the ramp, we can use the work-energy principle.

Work = Change in PE

W = PEf - PEi

where

W = work done (Joules)

PEf = final gravitational potential energy (Joules)

PEi = initial gravitational potential energy (Joules)

The gravitational potential energy of an object is given by the formula:

PE = mgh

where

m = mass of the object (200 N)

g = acceleration due to gravity (9.8 m/s^2)

h = height (4 meters)

We can find the change in potential energy as follows:

PEf = mgh = 200 x 9.8 x 4 = 7840 J

PEi = mgh = 200 x 9.8 x 0 = 0 J

So, the change in potential energy is 7840 J.

Now we can calculate the work done as:

W = PEf - PEi = 7840 - 0 = 7840 J

The work done is equal to the force exerted on the object multiplied by the distance it is moved:

W = F x d

7840 = F x 12

So, the force required to raise the box up the ramp is 653.33 N (7840/12)

Learn more about force from the given link.

https://brainly.in/question/23858054

#SPJ4

Our days would be a little bit shorter, and as a result, the sun would rise and set each day at later and later hours.

Another method to determine how long a day is is to time how long it takes a planet to complete one full spin. A sidereal day is what is being described here. On Earth, a sidereal day is almost exactly 23 hours and 56 minutes long. The sidereal day occurs after every 360-degree rotation of the Earth. It takes 23 hours, 56 minutes to do that. When Earth rotates slightly more and the sun is at the same location in the sky as it was 24 hours earlier, the solar day—the one that people count in the calendar—occurs.

To learn more about Earth refer to:

brainly.com/question/11902321

#SPJ4

The identical formula for the two angles is Asin(b),Asin(b).

The general word for interference effects involving edges or apertures is diffraction. In waves with longer wavelengths than those of light, diffraction is more common. Diffraction, for instance, is what causes sound to swell when it goes through a doorway or bend around corners. Diffraction causes water waves along a rocky coast to widen as they pass through the rocks. Usually, Fresnel and Fraunhofer diffraction regimes are distinguished.

Fresnel diffraction is the regime in which the diffracted waves are observed relatively close to the site of the diffraction (in comparison to the size of the item causing the diffraction). Working with Fresnel diffraction is typically very challenging. The Fraunhofer diffraction regime is the more manageable of the two.

angle 1 = asin(λb),

angle 2 = asin(−λb)

Learn more about angles visit: brainly.com/question/28293784

#SPJ4

The tension in the string can be found by using the equation for centripetal force. which is equal to 150.

This equation states that the centripetal force (Fc) is equal to the mass of the object (m) multiplied by the square of the velocity (v) and divided by the radius (r). Therefore,

Fc = m x v²/r.

In this case, the centripetal force is equal to the tension in the string, so the tension in the string (T) can be found by rearranging the centripetal force equation to

T = m x v²/r.

Substituting in the given values for mass (m) and radius (r) gives

T = 0.304 kg x (2.83 m/s)²/0.44 m

T= 150N

Therefore the tension of the string is 150N

Learn more about tension:

https://brainly.com/question/24994188

#SPJ4

Fortunately, even those who have the most severe instances of GBS eventually recover. Some people will still have some weakness when they recover.

The peripheral nervous system, or the network of nerves outside the brain and spinal cord, is mistakenly attacked by the body's immune system in the rare neurological illness known as Guillain-Barré syndrome (GBS). A person with GBS may experience anything from a very mild case with transient weakness to a nearly fatal paralysis that prevents them from breathing on their own.

Anyone can develop Guillain-Barré syndrome. Both sexes are equally prone to the illness, which can affect anyone at any age (although it tends to affect adults and elderly persons more frequently). One in 100,000 people are thought to be affected with GBS each year.

Learn more about system here-

https://brainly.com/question/11938296

#SPJ4

The required mass of the object with an acceleration of 10 m/s² and a force of 10 newtons to accelerate it is 1 kg.

From Newton's second's law of motion, force is described in equation form as, F = m × a

where, m is mass

a is acceleration

Given that,

Acceleration of an object = 10 m/s²

Force needed to accelerate the object = 10 N

Object's mass = ?

From the above equation, making mass as the subject, we have,

F = m × a

m = F/a = 10/10 = 1 kg

Thus, the required object's mass is calculated to be 1 kg.

To know more about mass:

https://brainly.com/question/13401016

#SPJ4

When labor is done, energy is transferred from the agent to the object, resulting in a change in the motion of the object (more specifically, a change in the object's kinetic energy).

Energy cannot be generated or destroyed, but it may be moved from one form to another. Energy may be altered in a variety of ways, such as when potential energy becomes kinetic energy or when one thing moves another.

Thermal energy is related to a system's internal energy because of its temperature. When a substance is heated, its temperature rises because its molecules begin to move faster, gaining thermal energy through heat transfer. Conduction, convection, and radiation are the three methods through which thermal energy is transferred.

Learn more about  energy to visit this link

https://brainly.com/question/1932868

#SPJ4

The work done during this period will be 1875 J. It will be positive if the body is displaced in the same direction of the force.

Work done can be defined as the product of applied force and the distance through which the body is displaced where the force is applied.

The value of work can be zero, positive and negative. It depends on the direction of the body displaced.

Data given in the question is;

Let F be the average force applied by the worker

D is the displacement = 15 m

The average force is ;

[tex]F_{avg=\frac{F1+F2}{2}[/tex]

[tex]F_{avg=\frac{210+40}{2}\\[/tex]

[tex]F_{avg=125 J[/tex]

The work done by the worker will be:

W=Fd

W=125x15

W=1875 J

Hence the work done during this period will be 1875 J.

To learn more about the work done:

brainly.com/question/3902440

#SPJ4

A visual representation of speed. It can also be used to denote speed. Without taking into account orientation, this is the rate of distance covered in a given amount of time.

The speed and direction of a particle's motion are both considered to be the particle's velocity. The distance travelled as well as the direction it is veering.

While velocity refers to both the speed and direction of an object's motion, speed is only the rate at which an object moves along a path over time. In other words, velocity is a vector, but on the other hand speed is a scalar value.

We know that velocity is a vector quantity since it has both a magnitude and a direction. However, speed just has a magnitude and no direction, therefore it.

To learn more about speed visit:

brainly.com/question/7359669

#SPJ4

The minimum-size copper equipment grounding conductor required for the circuit is 1/0 kcmil.

Learn more about conductors here:

https://brainly.com/question/492289

#SPJ4

The definition of constant velocity is the speed of a moving object that doesn't change over time. The system travelling at a constant speed is subject to zero net acceleration.

In contrast to instantaneous velocity, which is determined by slope of tangent line, average speed is defined as the shift in location (or displacement) during the course of transit.

Speed is the measure of velocity in magnitude. As a result, it is impossible to have two objects moving at the same velocity. The right response is therefore option A.

To know more about constant velocity visit :

https://brainly.com/question/2088385

#SPJ4

In 1957, Sputnik I was propelled into orbit around the planet. Its speed when it was at its perigee was was approximately 7.935 x 10^3 m/s.

The speed of an object in orbit around Earth can be calculated using the vis-viva equation:

v = sqrt(GM/(r))

where v is the velocity of the object, G is the gravitational constant, M is the mass of the Earth, and r is the distance of the object from the center of the Earth.

Given the perigee distance of 6.41 x 10^6 m and the mass of the Earth being 5.972 x 10^24 kg, the velocity of Sputnik I at its perigee would be:

v = sqrt((6.67 x 10^-11 N*(m^2)/(kg^2) * (5.972 x 10^24 kg)) / (6.41 x 10^6 m))

v = 7.935 x 10^3 m/s

So, the speed of Sputnik I when it was at its perigee was approximately 7.935 x 10^3 m/s.

To know more about speed please refer: https://brainly.com/question/13608672

#SPJ4

Answer:

True

Explanation:

In the definition of weight, W = mg, the mass m refers to an inertial mass.