a book with a mass of 0.25 kg is lifted 2 m onto a bookshelf. how much gravitational potential energy does it gain? ( g = 10 N/kg)​

Therefore, entropy is the measure of the disorder of a system.

To learn more about entropy refer to:

https://brainly.com/question/6677611

#SPJ4

A man is pushing a baby stroller. Compared to the magnitude of the force exerted on the stroller by the man, the magnitude of the force exerted on the man by the stroller is the same.

From Newton's third law of motion, the force exerted on the stroller by the man is same as the force exerted on the man by the stroller but is in the opposite direction.

Thus, the magnitude of the force exerted on the stroller by the man and the magnitude of the force exerted on the man by the stroller is same but in opposite direction.

To know more about force:

https://brainly.com/question/19657173

#SPJ4

In order to hit the target, the archer should aim the arrow so that it follows a parabolic trajectory.

The archer should aim the arrow slightly higher than the target, so that the arrow will arc downward and reach the target. Additionally, the archer should take into account other factors such as wind speed and direction, as these can affect the trajectory of the arrow.

The parabolic trajectory is a curve created when an object is thrown or shot in the air at an angle, then follows the path of a parabola. The parabolic trajectory allows for the object to travel in an arc and reach a certain distance, such as a target.

Learn more about parabolic trajectory:

https://brainly.com/question/28958414

#SPJ4

The radio wave's wavelength is 1.0 m. A waveform signal that is carried in space or down a wire has a wavelength, which is the separation between two identical places (adjacent crests) in the consecutive cycles.

The following formula was used to determine the frequency:

radio wave speed, c = radio wave frequency / radio wave length

c = f x λ

Because a radio wave is an electromagnetic wave and travels at the same speed as light, its speed, c = 3 x 108 m/s, is equal to the speed of light in this case.

When the formula

3 x 108= f x 1.0

f = 3 x 108/1

f = 3 x 108 Hz is used,

Radio waves therefore have a frequency of 3 x 108 Hz.

To know more about wavelength visit:-

https://brainly.com/question/13533093

#SPJ1

A jumbo jet can fly its whole length in 20 seconds at a certain speed and has a 284-foot length. The big jet taxied completely past a 710-foot-long hangar in 70 seconds while travelling at the same speed.

In physics, you can get average speed by dividing the total distance travelled by the total time needed to travel that distance. Speed is the rate of change in an object's position, expressed in metres per second. The rate at which an object travels a distance is considered its speed. High speed describes an object that is travelling quickly.

P should represent the plane's length in feet.

20p = (710+p)/20p = 14200+20p 50p = 14200 p = 284ft

Learn more about speed here

https://brainly.com/question/28224010

#SPJ4

The complex impedance of the 100 mH inductance when a voltage vL(t) = 10cos(2000πt) is applied to it is: j200Ω.

What is inductance?

Inductance is a property of an electrical component that describes the ability of the component to store energy in a magnetic field when electric current passes through it.

Inductance is measured in units of henrys (H). When current flows through a component with inductance, it creates a magnetic field around the component that resists changes to the current. This resistance to changes in current is called inductive reactance and is measured in units of ohms.

The complex impedance of an inductor is given by Z = jωL, where ω is the angular frequency and L is the inductance.
Therefore, the complex impedance of the 100 mH inductance when a voltage vL(t) = 10cos(2000πt) is applied to it is:
Z = j(2000π) (100 x 10-3) = j(2π) (100 x 10-3) = j200Ω

To learn about more inductance

https://brainly.com/question/7138348

#SPJ4

Accenture can assist its clients in being more sustainable thanks to the myNav. By making it easier to create cloud solutions that lower carbon emissions by rearranging manufacturing facilities such that carbon emissions can be calculated with ease.

by establishing new corporate efforts to lower transportation expenses and by establishing new rules for the disposal of out-of-date technology.

​reduces the expense of transportation

establishes sustainable guidelines for disposing of outdated technology.

myNav Green Cloud Advisor assists businesses in developing cloud solutions that cut carbon emissions and create a platform for ethical innovation. Green Cloud Advisor starts by establishing a baseline for the energy usage, compute needs, and sustainability objectives of current data centers.

To learn more about myNav Accenture from given link

https://brainly.com/question/30090589

#SPJ4

Salt dissolves in water to form saltwater. This kind of change is regarded as a chemical change.

A physical change is a kind of change in which only the physical properties of matter change. In a physical change, neither the composition nor the chemical nature of matter is changed.

A chemical change involves a chemical process that results in the production of new substances. When you dissolve salt in water the sodium chloride dissociates in Na+ and Cl- ions which can be written in the form of a chemical reaction as,

NaCl →  Na+(aq) + Cl-(aq)

Thus, dissolving salt in water is an example of a chemical change.

To know more about chemical change:

https://brainly.com/question/2496486

#SPJ4

The rate at which an object's position changes when observed from a specific point of view and when measured against a specific unit of time is known as its velocity.

Velocity is the direction at which an object is moving and serves as a measure of the rate at which its position is changing as seen from a specific point of view and as measured by a specific unit of time (for example, 60 km/h northbound).

By dividing the amount of time it took the object to go a certain distance by the overall distance, one can calculate the object's initial velocity. V is the velocity, d is the distance, and t is the time in the equation V = d/t.

An object's velocity can alter depending on whether it moves faster or slower or in a different direction. An object can move faster, slower, or remain stationary by being pushed or pulled in one direction or the other. Or to put it another way, a thing moves because of a force. Gravity and friction both act as sorts of forces that affect how an object moves.

Therefore, the correct answers are:

a) 75 m/s

b) 1.4 x 103m/s2

c) 2.8 x 103N

d) 75 m/s tangential object flight.

To learn more about velocity refer to:

https://brainly.com/question/25749514

#SPJ1

Answer:

 In places of hot climate, it is advised that the outer walls of house be painted white because white color does not absorb any heat radiation from the sun which keep inside cool even if there is hot climate outside the house.

The correct option is C. β-sheet type of protein secondary structure does the structure shown here (Figure 1) represent.

A shape is an arrangement and organization of interrelated elements in a fabric item or gadget, or the item or system so prepared. material systems encompass guy-made items consisting of homes and machines and natural items which include organic organisms, minerals, and chemical compounds. abstract structures consist of statistics structures in pc science and musical shape.

Sorts of the shape include a hierarchy (a cascade of one-to-many relationships), a network providing many-to-many links, or a lattice presenting connections among additives that can be pals in space.

Built structures are widely divided by using their various design approaches and requirements, into classes together with constructing systems, architectural structures, civil engineering structures, and mechanical structures.

To learn more about Structure visit here:

brainly.com/question/10730450

#SPJ4

Complete Question:

What type of protein secondary structure does the structure is shown here (Figure 1) represent?

A). α-helix

B). α-sheet

C). β- helix

D). β-sheet

E). γ turn

In the past eight years, there has been a 3% annual drop in the prevalence of stunting among Indian tribal children under the age of five.

To determine the predictors of stunting and severe stunting among tribal children, as well as to suggest potential policy and program implications, cross-sectional data from 1000 children (287 tribal and 713 non-tribal) aged 0-23 months from Odisha's Rapid Survey of Children (RSOC, 2014) were analyzed. The findings indicate that birth order and maternal illiteracy are significant predictors of childhood stunting, and that maternal age at marriage and at birth was less than 18 years old and less than 20 years old, respectively, for severe stunting. Basic factors such as poverty and maternal ages of 20 years at the time of the first birth and 18 years at marriage were found to predict severe stunting in tribal children.

Learn more about cross-sectional here-

https://brainly.com/question/14077757

#SPJ4

Dynamic stretching is typically recommended for individuals preparing for physical activity.

Dynamic stretching involves movements that gradually increase in range of motion and muscle length, such as arm swings, leg swings, and torso twists.

These exercises help to improve flexibility, range of motion, and muscular coordination, as well as increase blood flow to the muscles to prepare them for activity. Static stretching is best done after the activity to help reduce muscle soreness and keep the muscles flexible.

Learn more about Dynamic stretching:

https://brainly.com/question/1484910

#SPJ4

The above prompt is related to Interplanetary Science or Astronomy.

1) The diagram that best represents the appearance of the Moon at position P 'When viewed from the Earth is Option A.

2) The factor that most likely caused the difference in the apparent size of the Moon in photographs A and B is: "The distance from the Earth to the Moon changed." (Option D).

The study of planets and other objects in our solar system is known as interplanetary science. Telescopes, satellites, and other technologies are used by scientists to understand more about these objects and how they developed and evolved through time.

It also entails researching the possibility of life on other planets and moons, as well as learning about the solar system's past and future.

Learn more about Interplanetary Science:
https://brainly.com/question/858650
#SPJ1

The first one is based on the fundamental definition of velocity that employs the widely used velocity equation.

The second approach determines the amount of velocity change brought on by acceleration over a given period of time.

Finally, the average velocity formula is used in the third section of the velocity calculator, which may be helpful if you need to examine trips with varying speeds across different distances.

According to the definition of velocity, it is the rate at which an object's position changes over time. Consideration of body motion is one of the fundamental ideas in classical mechanics.

Therefore, The first one is based on the fundamental definition of velocity that employs the widely used velocity equation.

To learn more about Velocity, refer to the link:

https://brainly.com/question/18084516

#SPJ1

It is a passive stretch if it depends on an outside force. Stretches that are passive and static are a fantastic technique to increase flexibility and can also be utilised to cool down.

Passive stretching, which is called a static stretch, is a technique in which you remain calm and do not add to the range of motion. Static stretching involves stretching all the way to the end and holding the stretch. An external force, like a partner, is instead produced by an external force.

This stretching technique relies on a prop, accessory, or partner to help increase the stretch, thus you aren't actively assisting in extending your range of motion. Passive stretches improve flexibility while reducing muscle soreness and tiredness after a workout.

Stretching with movement is known as dynamic stretching. It stretches the muscles by using the muscles themselves. The usual "static" stretching is not like this.

To learn more about static stretching refer to:

https://brainly.com/question/10238897

#SPJ4

The mass of the pilot flying a small plane is 75.74 kg.

Centripetal acceleration is a characteristic of an object's motion along a circular path. Centripetal acceleration applies to any item travelling in a circle with an acceleration vector pointing in the direction of the circle's center.

Speed of the small plane: v = 130 m/s.

Radius of circular path: r = 400 meter.

Hence, centripetal acceleration: a = v²/r = (130)²/400  m/s² = 42.25 m/s²

Required force: F = 3200 N.

Hence, from Newton's 2nd law of motion:

The pilot's mass  = force/acceleration

= 3200/42.25 kg

= 75.74 kg.

Learn centripetal acceleration here:

https://brainly.com/question/14465119

#SPJ1

The increasing axon diameter increase the conduction velocity conduction in resistance capacitance because of the possibility of smooth movement of electrons in the capacitor and the smooth flow of charges in it that supports the electric current to flow in a smooth manner.

Capacitor is a body which is used to store the electricity in it and we can use it in the time when we need it in the circuit. also we can use the capacitor in the jumping the charge and electricity from the spark gap in the circuit to attain a good height and velocity as we needed it. by this information we can primarily consider that the increasing axon diameter increase the conduction velocity conduction in resistance capacitance because of the possibility of smooth movement of electrons in the capacitor and the smooth flow of charges in it that supports the electric current to flow in a smooth manner.

Learn more about capacitance:

brainly.com/question/12644355

#SPJ4

Add the x- and y-component squared values together, then take the square root of the result to determine the force's magnitude.

The distance between a vector's starting point P and ending point Q is its magnitude. The magnitude of PQ is represented symbolically as | PQ |. The Distance Formula can be used to determine a vector's magnitude if its start and end points' coordinates are known. We must add together all the forces acting on the item in the x and y directions in order to calculate the net gravitational force. The square root of the sum of the squares of these two values is then used to calculate.

Learn more about gravitational here-

https://brainly.com/question/3009841

#SPJ4

Based on the graph;

The work done by friction as the block travels from x =-0.04 to x = −0.02 m is 0.01 J.

The force exerted on the block by the spring at x = −0.02 m is 1 N.

The stiffness of a spring is indicated by the spring constant, k. For various springs and materials, it varies. The stiffer the spring is and the harder it is to stretch, the larger the spring constant. The spring constant is a measure of the spring's stiffness.

The force exerted by a spring of spring constant, k is given below as follows:

F = - kx.

where;

Learn more about spring constant at: https://brainly.com/question/23885190

#SPJ1

The relationship between mass thermal energy transfer kinetic energy and temperature is: When the temperature of an object raises, the average kinetic energy of its particles raises. When the average kinetic energy of its particles raises, the object's thermal energy raises.

The thermal energy in a substance is the whole kinetic energy of all the particles in the substance. If we warm a substance or object, as each particle speeds up, the average speed of the particles (temperature) raises, and accordingly the total speed (kinetic energy) of the particles (thermal energy).

The total of heat transferred is also directly proportional to the mass. To make an equivalent temperature change in a doubled mass, we need to add twice the heat.

Learn more about thermal energy at: https://brainly.com/question/18989562

#SPJ4

The object travelled 63 meters at 9m/s for 7 seconds.

The length of the trajectory taken between the initial and final positions of the moving body is the distance traveled.

To calculate the distance traveled by an object traveling horizontally off a cliff, you can use the formula:

d = v * t

where d is the distance traveled, v is the velocity (9 m/s), and t is the time (7 seconds).

By substituting the given values into the formula, we get:

d = 9 * 7 = 63 meters

So, the object traveled 63 meters horizontally before it hit the ground after being launched off the cliff at 9 m/s for 7 seconds.

To know more about distance, visit:

brainly.com/question/13034462

#SPJ1

The net force acting on the box, and the frictional force acting backward is 25 N

Here,

mass ,m = 12 Kg

F1 = 49 N

a = 2 m/s^2

Using the second law of motion

net force on the particle = m * a

net force on the particle = 12 * 2

the net force on the particle = 24 N

let the frictional force is f

F1 - f = Fnet

49 - f = 24

f = 25 N

The vector sum of all forces acting on an object is known as the net force. As a result of the fact that a force is a vector and that two forces with identical magnitudes and opposing directions cancel each other out, the net force is the sum of all the forces, or put another way, the net force is the sum of all the forces.

to know more about net force here:

brainly.com/question/29261584

#SPJ4

Man must exert energy to ascend the steps. No, you can't get to the top right away. (When explaining, use the analogy of an electron to represent a man.)

You can ascend stairs with the aid of stored muscular energy, and in this case, you obtain potential energy since you gain height while doing so.

None of the voids between the orbits may be occupied by the electron. The rungs of a ladder serve as a commonplace illustration of the Bohr model. You can only be on certain rungs of a ladder as you climb or descend it; you cannot be in the spaces between the rungs. Man must exert energy to ascend the steps. No, you can't get to the top right away. (When explaining, use the analogy of an electron to represent a man.)

Learn more about energy here-

https://brainly.com/question/24284560

#SPJ4

The magnitude of the centripetal acceleration of the car is 0.0034 km/sec².

Centripetal acceleration is the acceleration of an object moving in a circular path. It is directed towards the center of the circle and is responsible for the change in direction of the object's velocity.

The magnitude of the centripetal acceleration of an object moving in a circle is given by the formula:

a = v² / r

where a is the centripetal acceleration, v is the velocity of the object, and r is the radius of the circle.

Given that the car goes once around the track in 320 s, we can calculate its velocity by using the formula:

v = d / t

where d is the distance traveled and t is the time.

d = 2pir = 2pi3.0 km = 18.849 km

t = 320 sec

so the velocity of the car is v = 18.849 km / 320 sec = 0.059 km/sec.

We can now use the formula to find the centripetal acceleration of the car

a = v² / r = (0.059 km/sec)²/ 3.0 km = 0.0034 km/sec²

Hence, the magnitude of the centripetal acceleration of the car is 0.0034 km/sec².

To learn more about centripetal acceleration from the given link:

https://brainly.com/question/14465119

#SPJ4

The wave pulses always travel in the same direction. Each pulse differs significantly in terms of amplitude. Va = vb = vc as a result.

Pulses come in a wide variety of sizes and forms and are just dried seeds from legumes. The four most popular pulses—beans, chickpeas, lentils, and peas—and some of its variants will be described, illustrated, and given common names in this book.

The edible seed of a legume plant is known as a pulse. Peas, lentils, and beans are examples of pulses. As an illustration, a pea pod is a legume, while the pea within is a pulse.

The fastest and slowest waves should be calculated. The three scenarios in the illustration each illustrate a different amplitude of the wave with the same string.

Consequently, va = vb = vc.

Learn more about pulses visit: brainly.com/question/3521932

#SPJ4

The given statement is false. Due of their athleticism and muscular bodies, exceptional athletes like LeBron James or Michael Jordan transcend the laws of physics.

Laws of Physics are by their very nature statements of facts that have been inferred and developed from empirical data. Simply said, physical laws are a technique of categorizing how the world behaves when it comes to "functioning."

When an object interacts with another object, it experiences a push or pull known as a force. Every time two objects come into contact, a force is applied to each one of them.  Actual forces can only be created by interaction.

Learn more about law of physics from the given link.

https://brainly.com/question/24468880

#SPJ4

According to the question the rotational kinetic energy of a 12-kg motorcycle wheel is 809.14 J

The SI unit for rotational kinetic energy is the joule (J). The rotating kinetic energy formula has a similar structure to a translational kinetic energy equation. Kinetic energy is created by spinning objects around an axis. This type of energy is influenced by the object's mass, weight, and center of mass angle with respect to the axis.

Given data -

Mass = 12-kg

Angular velocity (ω) -120rad/s

inner radius = 0.280 m

outer radius = 0.330 m.

By using the formula

I = ½*M (r1² + r2²)

I = ½ *(12) * (0.2802 + 0.3302)

I = 1.1238 Kgm2

K.E = ½*Iω2

K.E = ½ * (1.1238)*(120)2

K.E = 809.14 J

To know more about rotational kinetic energy visit :-

https://brainly.com/question/30079962

#SPJ4

The correct answer to the given question is -6.944 * 10^-28 Joules

a. To find the electron's initial speed, we can use the conservation of energy. The initial kinetic energy of the electron must equal the final potential energy of the electron at its closest approach to the sphere.

Ki = 1/2 * me * v^2

v = sqrt(2Ki/me)

Ki = qe * V = (1.6 x 10^-19 C) * (-4.4 x 10^-9 C) = -6.944 x 10^-28 J

b. At the point where the speed of the electron is half of its initial value, the kinetic energy of the electron is half of its initial value. Therefore,

Ki/2 = 1/2 * me * (v/2)^2

we can solve for the distance from the surface of the sphere using the same equation as in part a, and substituting Ki/2 and v/2 for Ki and v respectively

c. The acceleration of the electron at its turning point can be found using the equation for centripetal acceleration:

a = v^2/r

where a is the acceleration, v is the speed of the electron, and r is the distance of the electron from the center of the sphere at its closest approach. We can use the value of v from part a and the distance from part b to find the acceleration.

Read more about Kinetic Energy from:

https://brainly.com/question/26472013

#SPJ4

The average angular acceleration has a value of 0.74 rad/s2.

Applying a force tangential to the rim and in the direction of the instantaneous velocity of the piece of the rim you are applying the force to will most likely increase the angular speed. Reversing the direction of the force will slow down the angular speed.

(rad/s)/s or rad/s2 are the units of angular acceleration. If rises, is a positive number. is negative if it decreases. Remember that the positive direction is counterclockwise and the negative direction is clockwise.

F = m r α . τ=mr2α. τ = m r 2 α

initial rotaton speed=10rad/s

final speed=6.3rad/s

time=5sec.

α=(10-6.3)/5 =.74rad/s

To know more about angular acceleration visit:-

https://brainly.com/question/14769426

#SPJ4