A 56 kg bungee jumper jumps off a bridge and undergoes simple harmonic motion. If the period of oscillation is 11.2 s, what is the spring constant of the bungee cord, assuming it has negligible mass compared to that of the jumper

To find the energy of a photon with a given wavelength, you can use the equation E = hc/λ, where E is the energy, h is Planck's constant, c is the speed of light, and λ is the wavelength.

Without knowing the specific wavelength provided in the question, it's not possible to calculate the energy in electron volts. However, as an example, let's assume the wavelength provided is 500 nm (nanometers). Using the equation E = hc /λ, we can calculate the energy as:

E = (6.626 x 10^-34 J s) x (2.998 x 10^8 m/s) / (500 x 10^-9 m)

E = 3.97 x 10^-19 J . To convert this energy to electron volts, we can use the conversion factor 1 eV = 1.602 x 10^-19 J:

E = (3.97 x 10^-19 J) / (1.602 x 10^-19 J/eV)

E = 2.48 eV

Therefore, a photon with a wavelength of 500 nm has an energy of 2.48 electron volts.

Learn more about energy  here;

https://brainly.com/question/31483568

#SPJ11

The work done on the canister by the 5.0 N force during this time is zero joules

Since the only force acting on the canister is in the xy plane, we can assume that the force is at some angle to the x-axis. Let's call this angle θ.

The work done by a force is given by the formula:

W = Fd cos(θ)

We can find the distance moved by the canister using its initial and final velocities. Since the acceleration is constant, we can use the kinematic equation: v_f^2 = v_i^2 + 2ad

where v_f is the final velocity, v_i is the initial velocity, a is the acceleration, and d is the distance moved.

Using the y-component of Newton's second law, we can find the acceleration: F_y = ma_y

5.0 N = (1.9 kg) a_y

a_y = 2.63 m/s^2

Using the kinematic equation, we can find the distance moved by the canister in the y-direction:

v_f^2 = v_i^2 + 2ad_y

(7.5 m/s)^2 = (5.5 m/s)^2 + 2(2.63 m/s^2) d_y

d_y = 1.35 m

Now we can find the work done on the canister:

W = Fd cos(θ)

W = (5.0 N)(1.35 m) cos(90°)

W = 0 J

Since the force is perpendicular to the direction of motion, the angle between the force and the direction of motion is 90 degrees and the cosine of 90 degrees is zero.

Learn more about  force here:

https://brainly.com/question/13191643

#SPJ11

The gravitational acceleration on planet X is about 0.405 times that of Earth's.

The period, T, of a simple pendulum is given by:

T = 2π√(L/g)

where L is the length of the pendulum and g is the gravitational acceleration. If we assume that the length of the pendulum remains constant between Earth and planet X, we can write:

T_X/T_Earth = √(g_Earth/g_X)

where T_X is the period on planet X and T_Earth is the period on Earth. We can substitute the given values to get:

1.530 s/2.243 s = √(g_Earth/g_X)

Squaring both sides of the equation, we get:

(g_Earth/g_X) = (2.243/1.530)^2 = 2.467

Therefore, the ratio of g_X/g_Earth is:

g_X/g_Earth = 1/g_Earth/g_X = 1/2.467 = 0.405

So the gravitational acceleration on planet X is about 0.405 times of Earth's.

To learn more about ratio, refer below:

https://brainly.com/question/31945112

#SPJ11

The slit separation is approximately 2.14 µm.

To find the slit separation, we can use the formula for double-slit interference:

sin(θ) = m * (λ / d)

where:
θ is the angle between the central maximum and the m-th dark fringe,
m is the order of the dark fringe (e.g., m = 1 for the first dark fringe),
λ is the wavelength of the light (450 nm),
d is the slit separation, and
tan(θ) ≈ y / L (small angle approximation).

In this case, we have:
y = 3.90 mm (distance between dark fringes),
L = 1.8 m (distance between the slits and the screen).

To find the angle θ, we use the small angle approximation:

tan(θ) = y / L
θ = arctan(y / L)

We also know that for dark fringes, m is an integer (1, 2, 3, ...), so we can use the formula for double-slit interference:

sin(θ) = m * (λ / d)

For the first dark fringe (m = 1), we have:

sin(arctan(y / L)) = λ / d

Now, we can solve for d:

d = λ / sin(arctan(y / L))

Plugging in the given values (λ = 450 nm, y = 3.90 mm, L = 1.8 m):

d = (450 nm) / sin(arctan(3.90 mm / 1.8 m))

After calculating, we get:

d ≈ 2.14 x 10^(-6) m or 2.14 µm

Learn more about double-slit interference here: https://brainly.com/question/29235908

#SPJ11

If an object has particles that are moving very slowly, the object's temperature is probably low.

Temperature is a macroscopic property that quantifies the average kinetic energy of particles within a system.

The kinetic energy of an individual particle is related to its speed, as kinetic energy (KE) is given by the equation KE = 1/2 * mv^2, where m is the mass of the particle and v is its velocity.

In a system with particles moving very slowly, it implies that the average speed of the particles is low. This low average speed translates to a lower average kinetic energy for the particles within the system.

Since temperature is a measure of the average kinetic energy, an object with particles moving slowly is likely to have a low temperature.

To understand this concept, consider a solid object at a low temperature. The particles in the object, such as atoms or molecules, have limited thermal energy and move slowly in a localized manner.

The individual particles vibrate or oscillate around their equilibrium positions, but their net displacement or overall motion is minimal.

As the temperature increases, the average kinetic energy of the particles also increases. This leads to more vigorous and rapid motion of the particles. In a gas, for example, higher temperatures result in faster random motion of the gas molecules.

Therefore, if an object has particles that are moving very slowly, it is an indication that the average kinetic energy and, consequently, the temperature of the object are low.

To learn more about kinetic, refer below:

https://brainly.com/question/26472013

#SPJ11

40 N is the usual force that the path at point B normally applies to the block. It is not necessary to understand the friction properties to calculate the normal force.

The block is travelling at a speed of 4 m/s in a circle with a radius of 1.5 m at point B. The net force in the radial direction is 0 since there is no acceleration in that direction. As a result, the path's normal force N is the only force acting on the block in the radial direction.

The normal force produces the centripetal force necessary to maintain the block's circular motion. As a result, the centripetal force and the normal force can be compared:

mv^2/r = N

where r is the radius of curvature, v is the speed of the block, and m is its mass. Inputting the values provided yields:

40 N is equal to N = (2 kg)(4 m/s)2/(1.5 m)

therefore the typical 40 N of force is applied to the block by the path at point B. The friction qualities need not be understood because we are just interested in the block's radial motion.

learn more about force here:

https://brainly.com/question/13191643

#SPJ11

To answer your question, we need to use the formula for the resonant frequency of an LC circuit, which is:  

f =n 1/(2π√(LC))  where f is the resonant frequency in Hertz, L is the inductance in Henrys, and C is the capacitance in Farads.

We want our circuit to radiate a wavelength of 4.5 m, which corresponds to a frequency of:

f = c/λ = 3 x 10^8 m/s / 4.5 m = 66.67 MHz
Now, we can rearrange the formula above to solve for L: L = 1/(4π^2f^2C)
Plugging in the values we have, we get:
L = 1/(4π^2 x (66.67 x 10^6)^2 x 2.4 x 10^-12) = 12.9 μH
So, an inductor of 12.9 μH should be used in series with the capacitor of 2.4 pF to form an oscillating circuit that will radiate a wavelength of 4.5 m.
it's important to note that LC circuits, or resonant circuits, are used in a variety of electronic applications, such as radio and TV broadcasting, wireless communication, and power conversion. These circuits rely on the interaction between an inductor and a capacitor to store and transfer energy between them, resulting in a resonant frequency that can be tuned to a specific value.

the resonant frequency is determined by the values of L and C in the circuit and is affected by the physical dimensions and materials of the components. In the case of your question, we calculated the value of inductance that, in combination with the given capacitor, would result in a resonant frequency that would radiate a specific wavelength. This is important in the context of antenna design, where the goal is to radiate electromagnetic waves of a specific frequency and wavelength for communication or sensing purposes. Overall, LC circuits and resonant circuits play an important role in modern electronics and are critical to many applications.

For more information on resonant frequency see:

https://brainly.com/question/13191113

#SPJ11

The excess charge across a typical cell membrane is about -7.5 picocoulombs.

The amount of excess charge (Q) in picocoulombs (pC) can be calculated using the equation:

Q = C × V

Where C is the capacitance of the membrane and V is the voltage across the membrane.

The capacitance of a typical cell membrane is about 1 µF/cm², which is equivalent to 10⁻⁶ F/cm² or 10⁻¹² F/Ų. Assuming the membrane has an area of 1 µm², the capacitance of the membrane can be calculated as:

C = 10⁻¹² F/Ų × (10⁻⁴ cm)² = 10⁻¹⁰ F

The voltage across the membrane is typically around -70 mV to -80 mV in resting conditions. Assuming a voltage of -75 mV, the excess charge (Q) can be calculated as:

Q = C × V = (10⁻¹⁰ F) × (-75 × 10⁻³ V) = -7.5 × 10⁻¹³ C

Converting to picocoulombs:

Q = -7.5 × 10⁻¹³ C × (10¹² pC/C) = -7.5 pC

Learn more about capacitance here:

https://brainly.com/question/28445252

#SPJ11

The spring constant of the spring is approximately 550.62 N/m when a 1.77 kg mass is attached to one end of a spring.

To find the spring constant (k), we'll need to use the given information and apply the formula for the potential energy stored in a spring:
Potential Energy (PE) = [tex]0.5 * k * (distance)^2[/tex]
First, let's convert the given distance (7.39 cm) to meters:
7.39 cm = 0.0739 m
We are given the total mechanical energy of the system (1.50 J) and since there's no mention of kinetic energy, we can assume that the entire energy is stored as potential energy in the spring. Therefore, we have:
[tex]1.50 J = 0.5 * k * (0.0739 m)^2[/tex]
Now, we'll solve for the spring constant (k):
[tex]1.50 J = 0.5 * k * 0.00546821 m^2[/tex]
To isolate k, divide both sides by ([tex]0.5 * 0.00546821 m^2[/tex]):
k = [tex]1.50 J / (0.5 * 0.00546821 m^2)[/tex]
k ≈ 550.62 N/m

To learn more about spring constant click here https://brainly.com/question/14159361

#SPJ11

Calculate the result in this equation: [tex]J = 15 A / (A_outer - A_inner)[/tex]and you'll find the current density in the wire. We need values to attain this.

To find the current density in the wire, we'll need to use the formula:

Current Density (J) = Current (I) / Cross-sectional Area (A)

First, we need to find the cross-sectional area of the hollow copper wire. We'll do this by finding the area of the outer circle and subtracting the area of the inner circle:

Outer radius (r_outer) = Outer diameter / 2 = 1.8 mm / 2 = 0.9 mm
Inner radius (r_inner) = Inner diameter / 2 = 1.1 mm / 2 = 0.55 mm

Area of outer circle (A_outer) =[tex]\pi  * r_(outer)^2 = \pi  * (0.9 mm)^2[/tex]
Area of inner circle (A_inner) =[tex]\pi  * r_(inner)^2 = \pi  * (0.55 mm)^2[/tex]
Cross-sectional Area (A) = A_outer - A_inner

Now, we'll calculate the current density:

J = I / A

Plug in the values:

J = 15 A / (A_outer - A_inner)

Calculate the result, and you'll find the current density in the wire.

Learn more about current here:

https://brainly.com/question/10174856

#SPJ11

The semimajor axis of the new planet orbiting a 2 MSun star with a 4-day period is approximately 0.05 AU.

The Doppler method allows astronomers to find the semimajor axis of an extrasolar planet's orbit by measuring its orbital period and the mass of the star it orbits.

For a new planet discovered orbiting a 2 MSun star with a period of 4 days, we can use the formula a = [[tex]P^2[/tex]G(M+M*)[tex]/4\pi ^2[/tex]][tex]^(^1^/^3^)[/tex], where P is the orbital period, G is the gravitational constant, M is the mass of the planet, and M* is the mass of the star.

Assuming the planet has a negligible mass compared to the star, we can simplify the formula to a = [(2MSun)(4 days)[tex]^2[/tex]G/4[tex]\pi ^2[/tex]]^(1/3), which yields a semimajor axis of approximately 0.05 AU.

This means the planet orbits its star at a distance of about 7.5 million km.

For more such questions on orbiting, click on:

https://brainly.com/question/28106901

#SPJ11

Net magnetic force on copper sheet at terminal velocity is zero.

The net magnetic force on the copper sheet at terminal velocity is zero.

This is because when an object reaches terminal velocity, the gravitational force is equal and opposite to the air resistance force.

In this case, the magnetic force on the copper sheet is proportional to the velocity of the sheet and the strength of the magnetic field.

As the sheet falls, the magnetic force increases until it reaches a point where it is equal and opposite to the gravitational force, and the sheet stops accelerating.

At this point, the net force on the sheet is zero and it continues to fall at a constant velocity of 2.0 m/s.

Therefore, the net magnetic force on the sheet after it reaches terminal velocity is zero.

For more such questions on velocity , click on:

https://brainly.com/question/80295

#SPJ11

The speed of the electromagnetic radiation in a vacuum for a radio wave with a frequency of 20.0 MHz is approximately 3.0 × 10^8 m/s.

To find the speed of the electromagnetic radiation in a vacuum for a radio wave with a frequency of 20.0 MHz, you can use the following formula:

Speed of Electromagnetic Radiation = Frequency × Wavelength

In this question, you are given the frequency (20.0 MHz) and you need to find the speed of the electromagnetic radiation in a vacuum. The speed of electromagnetic waves in a vacuum is constant, which is approximately 3.0 × 10^8 meters per second (m/s).

To find the wavelength, you can use the formula:
Wavelength = Speed of Electromagnetic Radiation / Frequency

Now, convert the frequency to Hz:
20.0 MHz = 20.0 × 10^6 Hz

Then, plug the values into the formula:
Wavelength = (3.0 × 10^8 m/s) / (20.0 × 10^6 Hz)
Wavelength ≈ 15 meters

Now that you have the wavelength, you can find the speed of the electromagnetic radiation in a vacuum using the formula:

Speed of Electromagnetic Radiation = Frequency × Wavelength
Speed of Electromagnetic Radiation ≈ (20.0 × 10^6 Hz) × 15 m
Speed of Electromagnetic Radiation ≈ 3.0 × 10^8 m/s

So, the speed of the electromagnetic radiation in a vacuum for a radio wave with a frequency of 20.0 MHz is approximately 3.0 × 10^8 m/s.

To learn more about electromagnetic radiation refer here:

https://brainly.com/question/10759891#

#SPJ11

Absorption of infrared (IR) radiation results in transitions among allowed vibrational motions in molecules.

Infrared spectroscopy is a powerful analytical technique that uses the interaction of molecules with IR radiation to identify and characterize chemical compounds.

When a molecule absorbs IR radiation, its vibrational energy increases, causing the bonds to stretch, bend, or twist. Each type of vibrational motion produces a characteristic pattern of absorption frequencies, which can be used to identify the functional groups present in the molecule.

The energy of the absorbed IR radiation is proportional to the frequency of the vibration, which in turn is related to the mass and stiffness of the atoms involved in the bond. Therefore, IR spectroscopy is a sensitive method to detect and quantify small changes in molecular structure, such as the presence of impurities, chemical reactions, and physical changes.

learn more about radiation here:

https://brainly.com/question/13934832

#SPJ11

An electron jump refers to the transition of an electron between different energy levels in an atom. Energy levels represent the specific amounts of energy that an electron can have within an atom.

When an electron transitions from a higher energy level to a lower one, it emits a photon, which is a particle of light. In the given question, an electron is currently in energy level 3. To emit the lowest energy photon, the electron must make a jump to the closest lower energy level. Among the provided options, the electron jump from energy level 3 to energy level 2 (3 → 2) is the transition that would emit the lowest energy photon.

This is because the energy of a photon is directly proportional to the difference in energy levels between the initial and final states of the electron. A smaller difference in energy levels results in a lower energy photon being emitted. In this case, the transition from energy level 3 to energy level 2 has the smallest difference, resulting in the emission of the lowest energy photon.

To know more about electrons

https://brainly.com/question/860094

#SPJ11

The people sitting next to their radios who are receiving the news announcement through radio waves will receive the news first since radio waves travel much faster than sound waves. Even though they are much farther away, the radio waves will reach them before the sound waves reach the people sitting across the newsroom.

Assuming that the transmission is instantaneously broadcasted through both radio and sound waves, the people sitting next to their radios who are 95 km away would receive the news first. This is because radio waves travel at a much faster speed and would reach their destination nearly instantaneously compared to sound waves, which would take approximately 28 seconds to travel 95 km.

On the other hand, the people sitting across the newsroom who are 4.0 m away from the newscaster would receive the news through sound waves. Sound waves travel much slower than radio waves, and it would take only approximately 0.012 seconds for the sound waves to travel 4.0 m to reach their ears. However, this time delay is negligible compared to the delay caused by the radio waves travel time.

In summary, the people sitting next to their radios 95 km away would receive the news first, followed by the people sitting across the newsroom who receive the news through sound waves.

Learn more about sound waves here:

https://brainly.com/question/21995826

#SPJ11

The vertex of the hyperbolic mirror is located at the point (0, -9.20), which is 9.20 units below the center of the mirror.

Let the distance between the center of the mirror and either focus be denoted by "f". Then, the equation of the hyperbola is given by:

[tex]x^2 / a^2 - y^2 / b^2 = 1[/tex]

where "a" is the distance between the vertex and the center of the mirror.

x = 13, y = 13

Also, we know that the light ray directed at focus A is reflected to focus B. Therefore, the distance between the mount and focus A is equal to the distance between focus B and the mount. This gives us:

[tex]\sqrt{(x - a)^2 + y^2) }= \sqrt{(x + a)^2 + y^2)}[/tex]

Squaring both sides and simplifying, we get:

[tex]a^2 = x^2 + y^2[/tex] / 4 = 338 / 4 = 84.5

Hence, the distance between the vertex and the center of the mirror is:

a = [tex]\sqrt{84.5}[/tex]

Learn more about  hyperbolic mirror here:

https://brainly.com/question/12919615

#SPJ11

To solve this problem, we need to understand the concept of buoyancy. When an object is immersed in a liquid, it experiences an upward force called buoyant force, which is equal to the weight of the displaced liquid. This means that the balance will register a lower weight when the object is immersed in a liquid compared to when it is in air.

In this case, the object weighs 30 N in air and 20 N in water, which means it is displacing 10 N of water. Using the density formula, we can find the density of the object:

Density = Mass/Volume

Since the mass of the object is constant, we can say that Density ∝ 1/Volume. This means that the volume of the object decreases when it is immersed in water, which makes sense because water is more dense than air.

Now, when the object is immersed in the other liquid, it displaces a different amount of liquid, which results in a weight of 24 N on the balance. Let's call the density of this unknown liquid "ρ".

Using the same formula as before, we can say that:

Density of object = Density of liquid x Volume of displaced liquid

The volume of displaced liquid can be found by taking the difference between the volumes of the object in air and in the liquid. We know that the object has the same volume in air and in the unknown liquid, so:

Volume of displaced liquid = Volume in air - Volume in water

Volume of displaced liquid = (30/10) - (20/10) = 1 m^3

Substituting this into the formula above, we get:

Density of object = ρ x 1

ρ = Density of object = 10 N/m^3

Therefore, the density of the unknown liquid is 10 N/m^3.

1. Determine the weight of the water and unknown liquid displaced by the object using the spring balance readings:
  - Weight of water displaced = 30 N (in air) - 20 N (in water) = 10 N
  - Weight of unknown liquid displaced = 30 N (in air) - 24 N (in unknown liquid) = 6 N

2. Calculate the volume of the object using the weight of water displaced and the density of water (1,000 kg/m³):
  - Volume = Weight of water displaced / (Density of water × Gravity)
  - Volume = 10 N / (1,000 kg/m³ × 9.81 m/s²) ≈ 0.00102 m³

3. Calculate the density of the unknown liquid using the weight of the unknown liquid displaced and the object's volume:
  - Density of unknown liquid = Weight of unknown liquid displaced / (Volume × Gravity)
  - Density of unknown liquid = 6 N / (0.00102 m³ × 9.81 m/s²) ≈ 610 kg/m³

So, the density of the unknown liquid is approximately 610 kg/m³.

For more information on buoyancy visit:

brainly.com/question/19168433

#SPJ11

A simple pendulum is suspended from the ceiling of an elevator. The elevator is accelerating upwards with acceleration a. The period of this pendulum, in terms of its length L, g and a is    [tex]2\pi \sqrt{\frac{L}{g+a}}[/tex].

The period of a simple pendulum is given by the formula:

T = [tex]2\pi \sqrt{\frac{L}{g}}[/tex]

where T is the period, L is the length of the pendulum, and g is the acceleration due to gravity.

In the case of the pendulum in an accelerating elevator, we need to consider the effective acceleration experienced by the pendulum. Since the elevator is accelerating upwards with acceleration a, the net acceleration acting on the pendulum will be the sum of the acceleration due to gravity (g) and the acceleration of the elevator (a).

Therefore, the effective acceleration (g') experienced by the pendulum can be calculated as:

g' = g + a.

Using this effective acceleration, the period of the pendulum in terms of L, g, and a becomes:

T = [tex]2\pi \sqrt{\frac{L}{g'}}[/tex] = [tex]2\pi \sqrt{\frac{L}{g+a}}[/tex]

So, the period of the pendulum in an accelerating elevator is given by [tex]2\pi \sqrt{\frac{L}{g+a}}[/tex].

Learn more about pendulum at: https://brainly.com/question/26449711

#SPJ11

The angle of refraction in the glass submerged in water is approximately 53.1°.

Using Snell's Law, which states that the product of the index of refraction and the sine of the angle of incidence (n1 × sinθ1) is equal to the product of the index of refraction and the sine of the angle of refraction (n2 × sinθ2), we can find the angle of refraction in glass.

In this case,
Index of refraction of water (n1) = 1.33
Index of refraction of glass (n2) = 1.5
Angle of incidence in water (θ1) = 60°

We want to find the angle of refraction in glass (θ2).

Using Snell's Law: n1 × sinθ1 = n2 × sinθ2
1.33 × sin(60°) = 1.5 × sinθ2

Now we solve for θ2:
sinθ2 = (1.33 × sin(60°)) / 1.5
sinθ2 ≈ 0.799

θ2 = arcsin(0.799)
θ2 ≈ 53.1°

So, the angle of refraction in glass is approximately 53.1°.

Learn more about Snell's Law here: https://brainly.com/question/28747393

#SPJ11

An aircraft's true airspeed (TAS) is affected by changes in the outside air temperature (OAT). When the OAT decreases, the air density increases, and this results in an increase in the aircraft's TAS. This is because as the air density increases, there are more air molecules available to create lift, and this reduces the amount of drag experienced by the aircraft.

In simple terms, if the aircraft is flying at a constant power setting and indicated altitude, and the OAT decreases, the TAS will increase. This means that the aircraft will cover more ground in a given amount of time, and the speedometer will indicate a higher speed.

It is essential for pilots to take into account changes in OAT when calculating their TAS, as this affects their fuel consumption, flight time, and overall performance. Understanding the relationship between OAT and TAS is crucial for safe and efficient flying.

Learn more about speedometer here:

https://brainly.com/question/29098798

#SPJ11

A 24 N force is applied to an object that moves 10. m in the SAME direction during the time that the force is applied.

The work done on an object is given by the formula

W = Fdcos(theta)

Where W is the work done, F is the applied force, d is the displacement of the object, and theta is the angle between the force and displacement vectors.

In this case, the force and displacement are in the same direction, so the angle between them is 0 degrees, and cos(0) = 1. Therefore, the work done is

W = Fdcos(theta) = 24 N * 10. m * cos(0) = 240 J

Hence, the work done to the object is 240 Joules.

To know more about force here

https://brainly.com/question/28773570

#SPJ1

the speed of the waves going past the pier is approximately 20.0 m/s.

The time it takes for a wave crest to move past a fixed point is known as the period of the wave, which is represented by the symbol T. The period is related to the frequency of the wave, which is the number of wave crests that pass a fixed point per unit time. The frequency is represented by the symbol f, and it is related to the period by the formula:

f = 1 / T

In this problem, the time it takes for the bobber to move from its highest point to its lowest point is given as 2.4 s. This time corresponds to the period of the wave, since it is the time it takes for one complete wave crest to pass the pier. Therefore, we can find the frequency of the wave using the formula above:

T = 2.4 s

f = 1 / T

= 1 / 2.4 s

= 0.4167 Hz

The distance between adjacent wave crests is given as 48 m. This distance is called the wavelength of the wave, which is represented by the symbol λ. The speed of the wave, represented by the symbol v, is related to the frequency and wavelength by the formula:

v = fλ

Substituting the values we found above, we get:

f = 0.4167 Hz

λ = 48 m

v = fλ

= 0.4167 Hz x 48 m

= 20.0 m/s

what is frequency?

Frequency refers to the number of occurrences of a repeating event per unit of time.

To know more about the  Frequency visit:

brainly.com/question/5102661

#SPJ11

According to Newton's law of universal gravitation, the force of gravity between two objects is proportional to their masses and inversely proportional to the square of their distance.

In this scenario, the force of gravity between the two rocks will be stronger on the side of the rock with higher mass, and weaker on the side of the rock with lower mass. Therefore, rock T will be pulled towards rock S with a stronger force than rock S is pulled towards rock T. As a result, rock T will accelerate faster towards rock S, and move faster than rock S. The actual speed of each rock will depend on their initial velocities and the strength of the gravitational force between them.

To know more about Newton's law of gravitation, click here:-

https://brainly.com/question/858421

#SPJ11

the new period of the system will be longer than the original period of 9.21 s.

we need to consider the relationship between the period of a pendulum and its length. The period of a pendulum is directly proportional to the square root of its length. When the performer stands up, the center of mass of the system is raised, increasing the length of the pendulum. This means that the period of the system will also increase.

We can use the formula for the period of a pendulum, T = 2π√(L/g), where T is the period, L is the length, and g is the acceleration due to gravity. We can rearrange this formula to solve for the new period:

T₂ = 2π√(L₂/g)

where L₂ is the new length of the pendulum after the performer stands up.

To find L₂, we need to add the distance that the center of mass was raised to the original length of the pendulum.

L₂ = L₁ + d

where L₁ is the original length of the pendulum and d is the distance that the center of mass was raised.

Substituting this into the formula for the new period, we get:

T₂ = 2π√((L₁ + d)/g)

We can now plug in the values given in the problem:

T₂ = 2π√((L₁ + 0.409 m)/9.81 m/s²)

T₂ = 2π√((L₁ + 0.0417)/1.00)

T₂ = 2π√(L₁ + 0.0417)

We don't have a numerical value for L₁, but we can see that the new period, T₂, will be longer than the original period, T₁.

when the performer stands up on the trapeze, the new period of the system will be longer than the original period of 9.21 s. This is because the center of mass of the system is raised, increasing the length of the pendulum and therefore its period.

To know more about mass visit:

https://brainly.com/question/19694949

#SPJ11

The answer is  1.08 km.

To find the distance travelled by the school bus, we can use the formula:

distance = speed x time

First, we need to convert the time of 3.5 minutes to hours. There are 60 minutes in an hour, so:

3.5 minutes ÷ 60 minutes/hour = 0.05833 hours

Now we can plug in the values:

distance = 18.5 km/h x 0.05833 hours

distance = 1.08 km

Therefore, the school bus travels a distance of 1.08 km to reach its first stop.

To find the distance the school bus travels at an average speed of 18.5 km/h for 3.5 minutes, follow these steps:

1. Convert the time (3.5 minutes) to hours: 3.5 minutes / 60 minutes per hour = 0.05833 hours
2. Use the formula for distance: Distance = Speed × Time
3. Plug in the values: Distance = 18.5 km/h × 0.05833 hours

The school bus's distance to its first stop is approximately 1.08 km.

to know more about average speed here:

brainly.com/question/12322912

#SPJ11

When the wavelength of the light in a double-slit experiment is increased, the interference pattern becomes more spread out.

In a double-slit experiment, light waves pass through two narrow slits and create an interference pattern on a screen behind the slits.

This pattern is created by the interference of the light waves, as they either add together constructively or cancel each other out destructively.

The distance between the slits and the screen, as well as the wavelength of the light, affects the spacing of the interference pattern.

When the wavelength of the light is increased, the spacing between the interference fringes becomes wider, causing the pattern to be more spread out.

Summary: Increasing the wavelength of light in a double-slit experiment leads to a more spread-out interference pattern on the screen behind the slits, due to the wider spacing between the interference fringes.

Learn more about wavelength click here:

https://brainly.com/question/10728818

#SPJ11

High-velocity stars are isolated stars that swing in and out of the plane of the galaxy at relatively high velocities with respect to the solar system. You would expect to find them in high-velocity stars predominantly in the halo of the galaxy

High-velocity stars are thought to originate from interactions between the Milky Way and other nearby dwarf galaxies or from gravitational interactions within globular clusters. These encounters can propel stars into eccentric orbits, causing them to travel through the galactic disk at high speeds. High-velocity stars can be classified into two main types: halo stars and runaway stars. Halo stars are typically old, metal-poor stars that have been part of the Milky Way's halo for a long time.

Runaway stars, on the other hand, are stars that have been ejected from their original location in the galactic disk due to various events such as supernovae or binary interactions. In both cases, high-velocity stars are fascinating objects for astronomers to study, as they provide valuable insights into the history and dynamics of our galaxy. So therefore you would expect to find high-velocity stars predominantly in the halo of the galaxy, as they are isolated stars that move in and out of the galactic plane at relatively high velocities compared to the solar system.

To learn more about Milky Way here:

https://brainly.com/question/30714548

#SPJ11

The cosmic microwave background is redshifted in the direction of Earth's motion (option a).

The cosmic microwave background is a faint radiation that fills the entire universe and is believed to be the afterglow of the Big Bang.

It has been found to be redshifted, meaning that its wavelengths have been stretched, in the direction of Earth's motion.

This effect is caused by the Doppler shift, which is the change in frequency or wavelength of a wave when the source or observer is moving relative to the other.

The cosmic microwave background has been mapped in detail by satellites such as the Cosmic Background Explorer and the Planck satellite, providing important information about the early universe, the formation of galaxies, and the nature of dark matter and dark energy.

Thus, the correct choice is (a) redshifted in respect to how the Earth is moving.

For more such questions on motion, click on:

https://brainly.com/question/26083484

#SPJ11

The star is actually a binary star system. A binary star system consists of two stars that orbit around a common center of mass. These stars are gravitationally bound to each other and are often referred to as a binary star or a double star.

A binary star system is a system of two stars that are gravitationally bound to each other, orbiting around a common center of mass. These stars can be of similar or different sizes, and can have various distances and periods of revolution.

The study of binary star systems is important in astrophysics, as they provide a means to measure the masses of stars, which is a crucial parameter for understanding their evolution. By observing the period and shape of the stars' orbits, astronomers can determine their masses and infer other properties, such as their radii and luminosities.Binary star systems can also interact in various ways, such as through mass transfer or merging, which can lead to the formation of exotic objects such as neutron stars or black holes.

To learn more about Binary star system visit here:

brainly.com/question/18415534

#SPJ4