The possible wavelengths of standing waves on a string of length L are given by the formula: λ = 2L/n, where n is an integer (1, 2, 3, ...) (a) The longest wavelength occurs when n = 1, so:
λ1 = 2L/1 = 2(120 cm) = 240 cm
(b) The second longest wavelength occurs when n = 2, so:
λ2 = 2L/2 = 2(120 cm)/2 = 120 cm
(c) The third longest wavelength occurs when n = 3, so:
λ3 = 2L/3 = 2(120 cm)/3 ≈ 80 cm
(d) The standing wave patterns for the three wavelengths can be sketched as follows:
For λ1, there is one antinode in the center and two nodes at the ends of the string.
For λ2, there are two antinodes symmetrically placed along the string and one node at the center.
For λ3, there are three antinodes symmetrically placed along the string and two nodes at the ends.
Learn more about wavelength here:
https://brainly.com/question/31143857
#SPJ11
One force of 97 pounds and one force of 55 pounds act on a body at the same point so that the resultant force is 113 pounds. Find the angle between the resultant and the smaller force, to the nearest 10th of a degree.
The angle between the resultant force and the smaller force is approximately 46.1 degrees.
To solve this problem, we will use the Law of Cosines, which states that in any triangle, c^2 = a^2 + b^2 - 2ab*cos(C), where a, b, and c are the sides of the triangle, and C is the angle opposite side c.
In this case, the sides of the triangle are the two forces and the resultant force: a = 55 pounds, b = 97 pounds, and c = 113 pounds. We need to find the angle C between the resultant force and the smaller force (side a).
1. Substitute the given values into the Law of Cosines formula: 113^2 = 55^2 + 97^2 - 2*55*97*cos(C).
2. Calculate the values: 12769 = 3025 + 9409 - 10670*cos(C).
3. Subtract the constants: 335 = 10670*cos(C).
4. Divide by 10670: cos(C) = 335/10670 ≈ 0.0314.
5. Find the inverse cosine: C ≈ acos(0.0314) ≈ 46.1 degrees.
So, the angle between the resultant force and the smaller force is approximately 46.1 degrees.
Learn more about force here:
https://brainly.com/question/13191643
#SPJ11
Analysis:
Find the velocity of both carts before and after the collision in each trial.
Calculate the impulse experienced by both carts. Compare the values – what does this mean?
Calculate the change in the momentum using both the velocities and impulse.
Assess whether momentum was conserved.
Was kinetic energy conserved?
If the extra weight is placed on the red cart instead, how does this change the velocities before and after the collision?
The analysis involves calculating the velocity and impulse for both carts before and after the collision, assessing momentum and kinetic energy conservation, and comparing the results with and without extra weight on the carts.
The analysis involves calculating the velocities of the carts before and after the collision in each trial, as well as the impulse experienced by both carts. By comparing the impulse values, one can determine which cart experienced the greater force during the collision. The change in momentum can then be calculated using both the velocities and impulse, and the conservation of momentum can be assessed. If the kinetic energy is conserved, the sum of the kinetic energies of the carts before the collision should be equal to the sum of the kinetic energies after the collision. Finally, if the extra weight is placed on the red cart instead of the blue cart, this will change the velocities before and after the collision as well as the forces experienced by each cart.
Learn more about velocities here:
https://brainly.com/question/17127206
#SPJ11
Write an expression that relates the maximum stretch of the spring to the mass on the spring. What in the expression can be measured and what is constant
The expression relating maximum stretch to mass on the spring is x=Fmax/k
The maximum stretch of a spring can be related to the mass on the spring using Hooke's Law, which states that the force exerted on a spring is proportional to the displacement of the spring.
The expression for this law is F=kx, where F is the force exerted on the spring, x is the displacement of the spring, and k is the spring constant. This expression can be rearranged to solve for x, giving x=F/k.
The maximum stretch of the spring can be measured as the displacement x when the force exerted on the spring is equal to its maximum value.
The mass on the spring is constant and does not affect the expression, as it only affects the force exerted on the spring, which is already accounted for in Hooke's Law..
To learn more about : mass
https://brainly.com/question/86444
#SPJ11
What new process was added to our theory of planet formation to explain these surprising extrasolar planets? condensation evaporation disk formation migration
The correct option is D, The process that was added to our theory of planet formation to explain the surprising extrasolar planets is migration.
A planet is a celestial body that orbits around a star, is spherical in shape due to its own gravity, and has cleared its orbit of other debris. The eight planets in our solar system are Mercury, Venus, Earth, Mars, Jupiter, Saturn, Uranus, and Neptune.
Planets are formed from the same gas and dust that surrounds a young star, called a protoplanetary disk. Over time, this material comes together due to gravitational attraction and forms into larger and larger bodies, eventually creating planets. Planets can have various features such as atmospheres, moons, and rings. They also have different characteristics such as size, composition, and temperature, which can affect their ability to support life.
To learn more about Planet visit here:
brainly.com/question/15268075
#SPJ4
A light bulb is connected to a battery and to a coil. The light bulb is visibly lit. An iron core is first rapidly thrust into the coil, then rapidly withdrawn These 2 actions will temporarily
The two actions of rapidly thrusting and withdrawing the iron core into the coil will temporarily change the brightness of the light bulb.
When an iron core is rapidly inserted into the coil, it increases the magnetic flux within the coil. According to Faraday's Law of Electromagnetic Induction, this change in magnetic flux induces an electromotive force (EMF) in the coil, which affects the current flowing through the circuit. When the iron core is rapidly withdrawn, the magnetic flux decreases, again inducing an EMF in the coil. This changing current causes the brightness of the light bulb to fluctuate temporarily.
Rapidly inserting and withdrawing an iron core into a coil connected to a light bulb and battery will cause temporary changes in the light bulb's brightness due to the induced electromotive force in the coil as a result of the changing magnetic flux.
To know more about Faraday's Law of Electromagnetic Induction, visit:
https://brainly.com/question/13369951
#SPJ11
The thrusting and withdrawal of an iron core into a coil will temporarily increase and then decrease the magnetic field in the coil.
What is Thrust?
Thrust is a force that pushes an object forward, typically in the opposite direction to the one in which gas or liquid is being expelled. It is commonly associated with engines, such as those used in aircraft, rockets, and ships, where the expulsion of gases or liquids creates a reaction force that propels the vehicle or object in the opposite direction.
The iron core enhances the magnetic field by increasing the magnetic flux in the coil. When the core is withdrawn, the magnetic field collapses due to the induced electromotive force in the coil.
The thrusting and withdrawal of the iron core is a demonstration of electromagnetic induction, which is the basis of many electrical devices, including generators and transformers.
Learn more about Thrust from the given link
https://brainly.com/question/28807314
#SPJ4
What is the direction of net ocean current motion for the entire column of water affected by the Coriolis force for a location
A location's net ocean current motion is 90 degrees to the right of the location's predominant wind direction.
This is brought on by the Coriolis force, which causes moving objects in the Northern Hemisphere to be deflected to the right and in the Southern Hemisphere to the left. The Earth's rotation produces the Coriolis force, which deflects the direction of moving things like ocean currents. In the Northern Hemisphere, the deflection is to the right, while in the Southern Hemisphere, it is to the left. Because the wind propels the surface currents, which are subsequently deflected by the Coriolis force, the direction of net ocean current motion at a site is 90 degrees to the right of the direction of the prevailing wind. Large-scale ocean circulation patterns, including the Antarctic Circumpolar Current in the Southern Ocean and the Gulf Stream in the North Atlantic, are created as a result.
learn more about motion here:
https://brainly.com/question/22810476
#SPJ11
Galaxies all formed at the same time, long ago. If you observe two galaxies at different distances from you, the more distant one will... Group of answer choices actually be younger. appear the same age. appear younger. appear older. actually be older.
Galaxies all formed at the same time, long ago. If we observe two galaxies at different distances from us, the more distant galaxy will actually be older.
When we observe objects in space, we are looking back in time due to the finite speed of light. Light from distant objects takes time to reach us, so the farther away an object is, the longer it takes for its light to reach us.
In the context of galaxies, if two galaxies formed at the same time in the past, the one that is farther away will appear older because we are seeing it as it was when the light left the galaxy in the past. The light from the more distant galaxy has travelled a greater distance and taken more time to reach us, so we see it as it existed further back in time.
Therefore, the more distant galaxy will appear older when observed from Earth.
Learn more about galaxies at: https://brainly.com/question/1241789
#SPJ11
two loops are sitting next to each other in the same plane. The current I1 in loop 1 is increasing. What is the direction of the induced current in loop 2?A. The same direction as I1B. The opposite direction as I1C. There is no induced current
When the current I1 in loop 1 is increasing, an induced current is generated in loop 2 according to Faraday's law of electromagnetic induction. The direction of the induced current in loop 2 can be determined using Lenz's law,
which states that the induced current flows in a direction that opposes the change in the magnetic field that produced it.
In this case, the increasing current I1 in loop 1 produces a magnetic field around the loop, which passes through loop 2. To oppose this change in the magnetic field passing through loop 2, an induced current is generated in loop 2 that produces a magnetic field that opposes the magnetic field produced by loop 1.
Using the right-hand rule for electromagnetic induction, we can determine that the induced current in loop 2 will flow in the opposite direction to the current in loop 1. Therefore, the correct answer is:
B. The opposite direction as I1.
Learn more about current here:
https://brainly.com/question/13076734
#SPJ11
A force acts on a potato as it moves along the x-axis from the origin to 4.5 m. How much work is done by the force on the potato of 3.44 N/m3
The work done by the force on the potato as it moves along the x-axis from the origin to 4.5 m is 15.48 Nm
To calculate the work done by the force on the potato, we need to use the following formula:
Work = Force × Distance × cos(θ)
"Force" refers to the force acting on the potato, "Distance" represents the displacement of the potato along the x-axis, and "θ" is the angle between the force and the displacement.
In this case, the force acting on the potato is 3.44 N/m³, and the potato moves a distance of 4.5 m along the x-axis. Since the force is acting in the same direction as the displacement, the angle (θ) between them is 0 degrees. Therefore, cos(0) = 1.
Now, let's plug in the given values into the formula:
Work = (3.44 N/m³) × (4.5 m) × cos(0)
Work = (3.44 N/m³) × (4.5 m) × 1
By calculating, we find that the work done by the force on the potato is:
Work = 15.48 Nm
So, the work done by the force on the potato as it moves along the x-axis from the origin to 4.5 m is 15.48 Nm.
To know more about force visit
https://brainly.com/question/13191643
#SPJ11
A stone is dropped off a cliff and is in free fall. Every second that the stone is falling, its acceleration _______. View Available Hint(s)for Part A is increasing and its speed are constant is constant but its velocity is increasing is decreasing
The stone's acceleration is constant but its velocity is increasing.
When the stone is dropped off a cliff and is in free fall, it experiences a constant acceleration due to gravity.
This means that every second that the stone is falling, its acceleration is the same.
However, the stone's speed is not constant because it is increasing due to the acceleration.
The stone's velocity, which is its speed and direction, is also changing because it is moving in a downward direction. As the stone falls, it gains more velocity and its speed increases, but its direction remains the same.
Therefore, the correct answer is that the stone's acceleration is constant but its velocity is increasing.
For more such questions on acceleration , click on:
https://brainly.com/question/460763
#SPJ11
Two charges separated by one meter exert 1-N forces on each other. If the charges are pushed to 1/4 meter separation, the force on each charge will be
The force on each charge when they are pushed to 1/4 meter separation is 16 N.
F = (k[tex]q_1q_2[/tex])/r²
the charges are separated by one meter and exert 1-N forces on each other, we can use Coulomb's law to find the charges:
1 N = (9x[tex]10^{9[/tex]Nm²/C²) * [tex]q_1[/tex] * [tex]q_2[/tex]/ (1 m)²
Simplifying, we get:
[tex]q_1[/tex]* [tex]q_2[/tex]= 1/9x[tex]10^{9[/tex] C²
If the charges are pushed to 1/4 meter separation, we can use Coulomb's law again to find the new force on each charge:
F = (k[tex]q_1q_2[/tex])/r²
F = (9x[tex]10^{9[/tex]Nm²/C²) * [tex]q_1[/tex] * [tex]q_2[/tex]/ (1/4 m)²²
F = 16 * (9x[tex]10^{9[/tex] Nm²/C²) * [tex]q_1[/tex]* [tex]q_2[/tex]
Substituting [tex]q_1[/tex]*[tex]q_2[/tex] = 1/9x[tex]10^{9[/tex] C², we get:
F = 16 N
A charge is a fundamental property of matter that describes the interaction between particles through electromagnetic force. All matter is made up of atoms, which contain positively charged protons, negatively charged electrons, and neutral neutrons. The charge of a particle is measured in Coulombs (C).
Like charges repel each other, while opposite charges attract. This is known as Coulomb's Law, which states that the force between two charged particles is proportional to the product of their charges and inversely proportional to the distance between them. The charge can be transferred from one object to another through various processes such as friction, conduction, and induction. When charge is transferred, it is conserved, meaning the total charge of a closed system remains constant.
To learn more about Charge visit here:
brainly.com/question/11944606
#SPJ4
When the bug that is creating waves swims in the direction of the waves, how does the speed of the wave some distance away in front of the bug compare with the speed of the wave created by a stationary bug
When a bug creates waves while swimming, the speed of the wave some distance away in front of the bug is slower compared to the speed of the wave created by a stationary bug. This is because the bug is swimming in the direction of the waves, adding its own speed to the speed of the waves, making them appear to be slower.
The bug is essentially catching up to its own waves, causing them to bunch up in front of it, resulting in a shorter wavelength and slower speed. This phenomenon is known as Doppler effect, where the apparent frequency and wavelength of waves change due to the motion of the source. Therefore, the speed of waves in front of the bug is slower, but the frequency remains the same, causing a change in wavelength.
Hi! When a bug that creates waves swims in the direction of the waves, the speed of the wave in front of the bug will be greater than the speed of the wave created by a stationary bug. This is because the moving bug adds its own speed to the waves it generates, causing them to travel faster in the direction the bug is moving. In contrast, waves created by a stationary bug only have the speed generated by the bug's movement in the water. To summarize, a swimming bug generates faster waves in front of it compared to a stationary bug.
For more information on Doppler effect visit:
brainly.com/question/28106478
#SPJ11
A short time later, a smoldering hot object hits the ground at your feet. What do you call this thing
If a smoldering hot object hits the ground at your feet, it may be called a meteorite.
A meteorite is a solid piece of debris from an object such as a comet, asteroid, or meteoroid that originates in outer space and survives its passage through the Earth's atmosphere to reach the surface of the planet. As the meteorite enters the Earth's atmosphere, it becomes superheated due to friction with the air, causing it to glow brightly and potentially smolder or burn. If the meteorite survives this journey and strikes the ground, it can still be hot and smoldering.
It is also possible that the object is a meteorite, which is a solid piece of debris from space that has survived its passage through Earth's atmosphere and impacted the ground. Determining whether an object is a meteor or a meteorite involves analyzing its physical and chemical characteristics.
Learn more about friction here:
https://brainly.com/question/13000653
#SPJ11
In the United States we generate just _____% of our electricity from nuclear power while France generates ______% of their electricity from nuclear power
In the United States we generate just about 20% of our electricity from nuclear power while France generates about 70% of their electricity from nuclear power.
Nuclear power plays a significant role in the U.S. energy mix, but it is not the predominant source. The country relies on a combination of various energy sources, including coal, natural gas, renewables, and nuclear power.
On the other hand, France stands out as a leader in nuclear power generation. They generate approximately 70% of their electricity from nuclear power.
France has heavily invested in nuclear energy and has developed a robust nuclear infrastructure over the years. This high reliance on nuclear power has been a deliberate policy choice driven by factors such as energy security, reducing greenhouse gas emissions, and minimizing dependence on imported fossil fuels.
The disparity in nuclear power generation between the United States and France can be attributed to a range of factors, including differing energy policies, public perceptions, regulatory frameworks, and access to alternative energy resources. Each country has made distinct choices in shaping their energy landscapes based on their unique circumstances and priorities.
To know more about electricity refer here:
https://brainly.com/question/15277088
#SPJ11
The relationship among air pressure, temperature and density is expressed by the _________________________.
The relationship among air pressure, temperature and density is expressed by the Ideal Gas Law,
This law also known as the General Gas Equation, and this law describes the behavior of gases in terms of their pressure, volume, temperature, and number of particles. According to the law, the pressure of a gas is directly proportional to its temperature and the number of particles present in it, and inversely proportional to its volume and density. In simpler terms, when the temperature of a gas increases, the pressure it exerts also increases, assuming that the number of particles and volume remain constant.
Similarly, if the volume of a gas decreases while the number of particles and temperature remain constant, its pressure will increase. Lastly, if the density of a gas increases while its volume and temperature remain constant, its pressure will also increase. Overall, the Ideal Gas Law helps scientists better understand how air pressure, temperature, and density are interrelated, making it an essential tool in atmospheric science and meteorology.
To learn more about Ideal Gas Law here:
https://brainly.com/question/30458409
#SPJ11
A conducting device that produces a large current in order to generate a strong magnetic field is called __________ .
A conducting device that produces a large current in order to generate a strong magnetic field is called an "Electromagnet."
An electromagnet is a type of magnet in which the magnetic field is produced by the flow of an electric current. It consists of a coil of wire, usually wrapped around a core made of soft ferromagnetic material like iron. When an electric current flows through the coil, it generates a magnetic field. The strength of the magnetic field depends on the amount of current flowing through the wire and the number of turns in the coil.By passing a current through a wire wrapped around a core made of a magnetic material, a strong magnetic field is created. Electromagnets are used in a variety of applications, including motors, generators, and MRI machines.
An electromagnet is the conducting device responsible for generating a strong magnetic field by producing a large current. This versatile device is widely used in various applications, such as lifting heavy objects, powering motors, and acting as a key component in electrical devices like transformers and relays.
To know more about electromagnets, click here
https://brainly.com/question/3427992
#SPJ11
A 0.105-m x 0.233-m x 0.329-m block is suspended from a wire and is completely under water. What buoyant force acts on the block
The buoyant force acting on the block is approximately 80.91 Newtons (N).
To determine the buoyant force acting on the block, we need to consider Archimedes' principle, which states that the buoyant force experienced by an object immersed in a fluid is equal to the weight of the fluid displaced by the object.
The buoyant force (Fb) can be calculated using the formula:
Fb = ρ * V * g,
where ρ is the density of the fluid, V is the volume of the fluid displaced by the object, and g is the acceleration due to gravity.
In this case, the block is completely submerged in water, so the fluid is water with a density of approximately 1000 kg/m³.
To find the volume of the fluid displaced by the block, we can use the volume of the block itself, as the submerged portion of the block will displace an equivalent volume of water.
The volume (V) of the block is given by:
V = length * width * height.
Substituting the given dimensions, we have:
V = 0.105 m * 0.233 m * 0.329 m.
Calculating this, we find:
V ≈ 0.00824 m³.
Now, we can calculate the buoyant force:
Fb = 1000 kg/m³ * 0.00824 m³ * 9.8 m/s².
Evaluating this, we get:
Fb ≈ 80.91 N.
Therefore, the buoyant force acting on the block is about 80.91 Newtons (N).
To learn more about buoyant, refer below:
https://brainly.com/question/32138756
#SPJ11
In general, when a charged particle enters a uniform magnetic field at a nonzero angle, the resultant path of the charged particle will be __________ .
When a charged particle enters a uniform magnetic field at a nonzero angle, the resultant path of the charged particle will be curved.
This is because the magnetic field exerts a force on the charged particle that is perpendicular to both the direction of the magnetic field and the velocity of the charged particle. This force causes the charged particle to move in a circular or helical path, depending on the initial angle of entry and the strength of the magnetic field. The magnitude of the force depends on the charge of the particle, its velocity, and the strength of the magnetic field. The direction of the force is determined by the right-hand rule, where the direction of the force is perpendicular to both the magnetic field and the velocity of the charged particle.
To learn more about magnetic field click here https://brainly.com/question/23096032
#SPJ11
Sometimes a kicked football sails through the air without rotating, and at other times it tumbles end over end as it travels. With respect to the center of mass of the ball, how is it kicked in both cases
When a football is kicked without rotating, it means that the kicker has kicked the ball in such a way that the center of mass remains stable and unchanged during its flight.
This happens when the kicker strikes the ball at its center or slightly below it. On the other hand, when a football tumbles end over end during its flight, it means that the kicker has struck the ball off-center, causing it to rotate around its center of mass. This rotation is caused by the imbalance of forces acting on the ball, which leads to a torque that causes it to spin. Therefore, the way a football is kicked determines whether it will sail through the air without rotating or tumble end over end.
To learn more about forces visit;
https://brainly.com/question/13191643
#SPJ11
Calculate the de Broglie wavelength of: a) a He atom traveling at 1000 m/s (a typical speed at room temperature) b) Yourself traveling at 8 km/h (jogging speed)
Borglie wavelength of :
(a) we get λ = h/p = 6.63 x 10^-34 J s / 4.01 x 10^-22 kg m/s = 1.66 x 10^-10 m.
(b)we get λ = h/p = 6.63 x 10^-34 J s / 155 kg m/s = 4.28 x 10^-36 m,
The de Broglie wavelength is a concept that relates the momentum of a particle to its wavelength, according to the equation λ = h/p, where λ is the wavelength, h is Planck's constant, and p is the momentum of the particle.
a) For a He atom traveling at 1000 m/s, we can calculate its momentum by multiplying its mass (4.0026 u) by its velocity (1000 m/s), which gives us a momentum of 4.01 x 10^-22 kg m/s. Plugging this value into the de Broglie wavelength equation,
b) For a person jogging at 8 km/h (2.22 m/s), we can estimate their mass to be around 70 kg. Multiplying their mass by their velocity gives us a momentum of 155 kg m/s.
Plugging this value into the de Broglie wavelength equation, which is incredibly small compared to the size of a human.
In conclusion, the de Broglie wavelength is a useful concept for understanding the wave-particle duality of matter, and it can be calculated for both atomic particles and macroscopic objects like people.
To learn more about : Borglie wavelength
https://brainly.com/question/28093301
#SPJ11
If you carry a heavy bag of groceries and bang your hand against the wall, the concept that best explains why your hand hurts is gravity. inertia. resistance. none of the above g
The concept that best explains why your hand hurts is inertia.
When you carry a heavy bag of groceries and accidentally bang your hand against a wall, the concept that best explains why your hand hurts is inertia.
Inertia is the tendency of an object to resist changes in its state of motion, which includes changes in speed and direction.
When your hand hits the wall, it suddenly stops moving while the rest of your body is still in motion, causing a force to be exerted on your hand.
This sudden change in motion results in a painful sensation in your hand.
While gravity and resistance may play a role in other physical scenarios, inertia is the most relevant concept to explain this specific situation.
For more such questions on inertia , click on:
https://brainly.com/question/1140505
#SPJ11
in calculating apparent power in a three phase circuit the phase values of voltage and current are multiplied by
To calculate apparent power in a three phase circuit, the phase values of voltage and current are multiplied by the square root of three and the power factor.
The square root of three is used because in a three phase circuit, the voltage and current waves are out of phase with each other by 120 degrees. This means that the total voltage and current are greater than the individual phase values, and multiplying by the square root of three takes this into account.
The power factor is a measure of how efficiently the circuit is using the power, and is typically a value between 0 and 1. Multiplying by the power factor adjusts for any inefficiencies in the circuit and gives the apparent power. In summary, the long answer is that to calculate apparent power in a three phase circuit, the phase values of voltage and current are multiplied by the square root of three and the power factor.
In calculating the apparent power (S) in a three-phase circuit, the phase values of voltage (V) and current (I) are multiplied by the square root of 3 (√3). The formula for apparent power in a three-phase circuit is: S = √3 * V * I
To know more about apparent power, refer
https://brainly.com/question/31116183
#SPJ11
A screen is placed 55.0 cm from a single slit, which is illuminated with light of wavelength 690 nm. If the distance between the first and third minima in the diffraction pattern is 2.90 mm, what is the width of the slit
The width of the slit is approximately 3.68 μm.
The width of the slit can be determined using the formula for the diffraction pattern produced by a single slit:
sin(θ) = m * λ / w
where:
θ is the angle of the diffraction pattern,
m is the order of the minimum,
λ is the wavelength of the light, and
w is the width of the slit.
In this case, we are given the following information:
Distance between the first and third minima (y) = 2.90 mm = 2.90 × 10^(-3) m
Distance from the screen to the slit (L) = 55.0 cm = 0.55 m
Wavelength of light (λ) = 690 nm = 690 × 10^(-9) m
To find the width of the slit (w), we need to find the angle θ corresponding to the third minimum.
Using the small angle approximation, we can approximate sin(θ) ≈ θ, since θ is small.
Rearranging the formula, we have:
θ ≈ m * λ / w
For the third minimum (m = 3), we have:
θ ≈ 3 * λ / w
The distance on the screen corresponding to the third minimum (y) is related to the angle θ and the distance to the screen (L) as follows:
y ≈ L * θ
Substituting the approximations for θ and solving for w:
y ≈ L * (3 * λ / w)
w ≈ 3 * λ * L / y
Substituting the given values:
w ≈ 3 * (690 × 10^(-9) m) * (0.55 m) / (2.90 × 10^(-3) m)
Calculating the result:
w ≈ 3.68 × 10^(-6) m
Therefore, the width of the slit is approximately 3.68 μm (micrometers).
To learn more about diffraction, refer below:
https://brainly.com/question/12290582
#SPJ11
Suppose that σx = 399 MPa , σy = 206 MPa , τxy = 426 MPa .
part a-Determine the principal stress.
part b-Determine the maximum in-plane shear stress.
part c-Determine average normal stress.
part d-Specify the orientation of the maximum in-plane shear stress.
part e-Specify the orientation of the principal stress.
Max = 300 MPa is the maximum in-plane shear stress. The typical normal stress is equal to 302.5 MPa ((x + y) / 2). The highest in-plane shear stress is oriented 45 degrees away from the x-axis.
The major stress 1 is oriented 16.7 degrees away from the x-axis.
a) To determine the primary stresses, the quadratic equation 2 - (x + y) + (x y - 2) = 0 must be solved. We obtain the values 1 = 602.5 MPa and 2 = 2.5 MPa by plugging in the supplied values.
b) The equation max = (1 - 2) / 2 = 300 MPa can be used to calculate the maximum in-plane shear stress.
c) The average normal stress is simply (x + y) / 2 = 302.5 MPa, which is the average of x and y.
d) The equation p = 0.5 atan(2xy / (x - y)) can be used to determine the direction of the maximum in-plane shear stress. Using the values provided as plug-ins, we obtain p = 45 degrees from the x-axis.
e) The equation 1 = 0.5 atan(2xy / (x - y - 1 + 1)) can be used to determine the orientation of the major stress 1. Using the supplied data as a plug-in, we obtain 1 = 16.7 degrees from the x-axis.
learn more about shear stress here:
https://brainly.com/question/30328948
#SPJ11
A garden hose with an internal diameter of 2.1 cm is connected to a (stationary) lawn sprinkler that consists merely of a container with 24 holes, each 0.28 cm in diameter. If the water in the hose has a speed of 0.85 m/s, at what speed does it leave the sprinkler holes
The water leaves the sprinkler holes at a speed of approximately 1.994 m/s.
To determine the speed at which water leaves the sprinkler holes, you can use the principle of continuity, which states that the product of the cross-sectional area and the speed of the fluid is constant in a continuous flow system. In this case, the garden hose and the sprinkler holes form a continuous flow system.
Step 1: Calculate the cross-sectional area of the garden hose.
Area_ hose = π × (diameter _hose / 2)²
Area_ hose = π × (0.021 m / 2)²
Area_ hose ≈ 0.00034636 m²
Step 2: Calculate the cross-sectional area of a single sprinkler hole.
Area_ hole = π × (diameter _hole / 2)²
Area_ hole = π × (0.0028 m / 2)²
Area_ hole ≈ 6.1542e-6 m²
Step 3: Calculate the total cross-sectional area of all 24 sprinkler holes.
Area_ total = Area_ hole × number_ of_ holes
Area_ total = 6.1542e-6 m² × 24
Area_ total ≈ 0.0001477 m²
Step 4: Apply the principle of continuity to find the speed of the water leaving the sprinkler holes.
Area_ hose × speed_ hose = Area_ total × speed_ holes
speed _holes = (Area_ hose × speed_ hose) / Area_ total
speed_ holes = (0.00034636 m² × 0.85 m/s) / 0.0001477 m²
speed_ holes ≈ 1.994 m/s
To know more about principle of continuity :
https://brainly.com/question/30789807
#SPJ11
. (2 points) What will the escape velocity be when the Sun becomes a red giant with a radius 50 times greater and a mass only 0.9 times that of today?
The type of remote sensing in which the sensor generates its own energy, casts it at a target, and then measures the return of that form of energy, is:
The type of remote sensing you are describing is called active remote sensing.
In active remote sensing, the sensor emits energy in the form of electromagnetic radiation or sound waves and then detects and measures the energy that is reflected or scattered back from the target. This is different from passive remote sensing, where the sensor only detects energy that is naturally emitted or reflected by the target, such as sunlight or thermal radiation. Examples of active remote sensing include radar and lidar, which use radio waves and laser light, respectively, to measure the properties of the target.
Learn more about remote sensing here:
https://brainly.com/question/10839378
#SPJ11
Two point charges, initially 3 cm apart, experience a force, F. The charges are then moved to a distance of 12 cm apart. What is the new electric force between the charges
The electric force between the charges decreases to 1/16 of its original value.
When considering the force between two point charges, we can refer to Coulomb's Law, which states that the electric force (F) between two charges (q1 and q2) is directly proportional to the product of the charges and inversely proportional to the square of the distance (r) between them.
Mathematically, Coulomb's Law can be expressed as:
F = k * (q1 * q2) / r²
where k is Coulomb's constant (8.99 x[tex]10^{9}[/tex] N·m²/C²).
Initially, the charges are 3 cm apart, so r1 = 0.03 m.
Afterward, they are moved to a distance of 12 cm apart, so r2 = 0.12 m.
To find the new electric force (F2) between the charges, we can use the ratio of the initial force (F1) and the new force (F2), which is given by:
F1 / F2 = (r2²) / (r1²)
Since we know r1 and r2, we can calculate the ratio:
F1 / F2 = (0.12²) / (0.03²) = 16
This means that the new force (F2) is 1/16 times the initial force (F1). Therefore, when the distance between the two point charges increases from 3 cm to 12 cm, the electric force between them decreases to 1/16 of its original value.
know more about electric force here:
https://brainly.com/question/17164299
#SPJ11
A person pushes (horizontally) a 20 kg box 20m over a level surface at a constant speed. The coefficient of kinetic friction between the box and the surface is 0.4. How much work does the gravitational force do on the box during this motion
The work done by the gravitational force on the box is zero.
The gravitational force on the box during this motion remains constant and does not change as the box moves horizontally over the level surface. This is because the gravitational force acts vertically downwards, perpendicular to the direction of the horizontal motion. This is because the work done by a force is equal to the product of the force and the displacement in the direction of the force. Since the displacement of the box is in the horizontal direction and the gravitational force acts vertically downwards, the displacement and the force are perpendicular to each other, and hence the work done by the gravitational force is zero.
However, the work done by the person pushing the box against the frictional force is not zero. The frictional force acting on the box opposes the direction of motion, and the person has to exert a force equal in magnitude and opposite in direction to overcome this frictional force and maintain a constant speed. The work done by the person pushing the box is given by the product of the force applied and the displacement in the direction of the force. In this case, the force applied is the horizontal force exerted by the person, and the displacement is the distance the box is pushed horizontally.
Using the formula for work, W = Fd, where W is the work done, F is the force applied, and d is the displacement in the direction of the force, we can calculate the work done by the person pushing the box.
W = Fd = (20 kg) x (9.8 m/s^2) x (0.4) x (20m) = 1568 J
Therefore, the person pushing the box does 1568 J of work against the frictional force, while the gravitational force does zero work on the box during this motion.
Know more about work done here:
https://brainly.com/question/21854305
#SPJ11
Find the mechanical energy of a block-spring system having a spring constant of 1.5 N/cm and an oscillation amplitude of 3.9 cm.
The mechanical energy of a block-spring system having a spring constant of 1.5 N/cm and an oscillation amplitude of 3.9 cm is 11.41 J
The mechanical energy of a block-spring system can be found by using the formula:
E = 1/2 kA²
Where E is the mechanical energy, k is the spring constant (1.5 N/cm), and A is the amplitude of oscillation (3.9 cm).
Plugging in the values, we get:
E = 1/2 (1.5 N/cm) (3.9 cm)²
E = 1/2 (1.5 N/cm) (15.21 cm²)
E = 11.41 N cm or J (Joules)
Therefore, the mechanical energy of the block-spring system is 11.41 Joules.
Alternatively, to find the mechanical energy of a block-spring system, you can use the formula for the potential energy stored in the spring:
E = (1/2)kA²
where E is the mechanical energy, k is the spring constant (1.5 N/cm), and A is the oscillation amplitude (3.9 cm).
E = (1/2)(1.5 N/cm)(3.9 cm)²
E = 0.75 N/cm × 15.21 cm²
E = 11.41 N*cm
The mechanical energy of the block-spring system is 11.41 N*cm.
More on mechanical energy: https://brainly.com/question/31732604
#SPJ11