1. A manufacturing cell with two workers is responsible for producing a small frying pan with a required takt time of 496 seconds. The material passes through two processes: a deep drawing process and a trimming process. The average cycle time for the deep drawing process is 450 seconds and average cycle time for trimming is 430 seconds. (2 pts.)
a. Does the work cell have adequate capacity to meet demand? Explain.
b. What is the required daily production capacity of the work cell (in number of frying pans per day)? Assume 480 minutes/workday of available time.
2. What is the total daily idle time for both workers in Problem 1? Report your answer in (a) seconds of idle time and (b) as a percentage of total working time for the cell. (2 pts.)

Answer:

The right answer is "1.903 m".

Explanation:

Given that,

[tex]\tau =110 \ MPa[/tex]

[tex]G=80 \ GPa[/tex]

[tex]\Theta=15\times \frac{\pi}{180}[/tex]

   [tex]=\frac{\pi}{12}[/tex]

[tex]d=20 \ mm[/tex]

As we know,

⇒ [tex]\frac{\tau}{r}=\frac{G \Theta}{L}[/tex]

Or,

⇒ [tex]L=\frac{G \theta r}{\tau}[/tex]

       [tex]=\frac{80\times 10^3}{110}\times \frac{\pi}{12}\times 10[/tex]

       [tex]=1903.9 \ mm[/tex]

or,

       [tex]=1.903 \ m[/tex]

Answer:

Veracity, Value and Visualization are not only the characteristics of Big Data but are also the characteristics of relational databases. Veracity of data is issue with smallest data stores this is the reason that it is important in relation...

Answer:

8.6 ft³/s

Explanation:

The force due to the water jet F = mv where m = mass flow rate = ρQ where ρ = density of water = 62.4 lbm/ft³ and Q = volume flow rate. v = velocity of water jet = 30 ft/s

So, F = mv

F = ρQv

making Q subject of the formula, we have

Q = F/ρv

Since F = force due to water jet = force needed to hold the plate against the water stream = 500 lbf = 500 × 1 lbf = 500 × 32.2 lbmft/s² = 16100 lbmft/s²

Since

Q = F/ρv

Substituting the values of the variables into the equation for Q, we have

Q = F/ρv

Q = 16100 lbmft/s²/(62.4 lbm/ft³ × 30 ft/s)

Q = 16100 lbmft/s²/1872 lbm/ft²s

Q = 8.6 ft³/s

So, the volume flow rate is 8.6 ft³/s.

Answer:

≈ 0.516 m^3/hr

Explanation:

Inlet of compressor = 200 SCMH

sheer standard conditions = 1 atm and 288.5 K

For oxygen :

critical pressure(Pc) = 49.8 atm

critical temperature Tc = 154.6 K

hence at compressor inlet

Tr = T / Tc = 288.5/154.6 = 1.866

Pr = P / Pc = 1 / 49.8 = 0.0204

Z1 ( from compressibility chart ) = 0.98

at compressor outlet

P2 = 500 bar = 500*0.9869 = 493.45 atm  , T2 = 360 k

hence : Pr = P / Pc = 493.45 / 49.8 = 9.91

            Tr = T / Tc = 360 / 154.6 = 2.33

Z2 ( from compressibility chart ) ≈ 1

V2( volumetric flow rate ) = V1*(P₁Z₂T₂) / (P₂Z₁T₁)

                                         = 200 ( 1 * 1* 360) / (493.45 *0.98*288.5)

                                         = 0.516 m^3/hr

Answer:

The physical topology addresses how devices are connected, while a logical topology addresses how devices actually communicate to one another ( C )

Explanation:

Network physical is simply the process/method of connecting the Network using cables while Logical topology is the general architecture of the communication mechanism in the network for all nodes.

Hence The correct statement is the physical topology addresses how devices are connected, while a logical topology addresses how devices actually communicate to one another

Answer:

Explanation:

Given:

Q factor, =1000

natural frequency, [tex]f_n=2000~Hz[/tex]

Damping factor, [tex]\zeta=?[/tex]

Bandwidth, BW=?

We have the relation:

[tex]Q=\frac{1}{2\zeta}[/tex]

[tex]\zeta=\frac{1}{2Q}[/tex]

[tex]\zeta=\frac{1}{2\times 1000}[/tex]

[tex]\zeta=5\times 10^{-4}[/tex]

Bandwidth:

[tex]BW=\frac{f_n}{Q}[/tex]

[tex]BW=\frac{2000}{1000}[/tex]

[tex]BW=2~Hz[/tex]

Answer:

To become ASE certified, you must pass an ASE test and have relevant hands-on work experience. The amount of work experience required can vary by test, and is specified in detail here. ASE recommends submitting the form after you've registered to take an ASE certification test.

Good luck!

Explanation:

Answer:  One theme in White Fang is adapting in order to survive. White Fang finally submits to Gray Beaver. He also copes with fighting other dogs. White Fang changes his behaviors so that he can live.

Explanation: its the sample response

Answer:

first mark me as a brainleast

Answer:

The right answer is "2.2099 m³".

Explanation:

Given:

Mass,

m = 5 kg

Temperature,

T = 35℃

or,

  = 35 + 273

Pressure,

P = 200 kPa

Gas constant,

R = 0.2870 kj/kgK

By using the ideal gas equation,

The volume will be:

⇒ [tex]PV=mRT[/tex]

or,

⇒    [tex]V=\frac{mRT}{P}[/tex]

By substituting the values, we get

          [tex]=\frac{5(0.2870)(35+273)}{200}[/tex]

          [tex]=\frac{441.98}{200}[/tex]

          [tex]=2.2099 \ m^3[/tex]

Answer:

(i) 0

(iv) 8a+6b+c-70

Explanation:

Hope this helps you

Answer:

can you please give us the option for this question

Answer: Attached below is the missing detail and Mohr's circle.

i) б1 =  9.6 Ksi

б2 = -10.7 ksi

ii) 10.2 Ksi

iii)  -0.51Ksi

Explanation:

First step :

direct compressive stress on shaft

бd = P / π/4 * d^2

      = -20 / 0.785 * 5^2  = -1.09 Ksi

shear stress at the outer surface due to torsion

ζ = 16*T / πd^3

  = (16 * 250 ) / π * 5^3  = 010.19 Ksi

Calculate the Principal stress, maximum in-plane shear stress and average normal stress

Using Mohr's circle ( attached below )

i) principal stresses:

б1 = 4.8 cm * 2 = 9.6 Ksi

б2 = -5.35 cm * 2 = -10.7 ksi

ii) maximum in-plane shear stress

ζ  = radius of Mohr's circle

   = 5.1 cm = 10.2 Ksi   ( Given that ; 1 cm = 2Ksi )

iii) average normal stress

 = 9.6 + ( - 10.7 ) / 2

  = -0.51Ksi

answer

d just too the test

Answer:

a)  Δh = 2 cm,  b) Δh = 0.4 cm

Explanation:

Let's start by using Bernoulli's equation for the Pitot tube, we define two points 1 for the small entry point and point 2 for the larger diameter entry point.

            P₁ + ½ ρ v₁² + ρ g y₁ = P₂ + ½ ρ v₂² + ρ g y₂

Point 1 is called the stagnation point where the fluid velocity is reduced to zero (v₁ = 0), in general pitot tubes are used  in such a way that the height of point 2 of is the same of point 1

           y₁ = y₂

subtitute

           P₁ = P₂ + ½ ρ v₂²

           P₁ -P₂ = ½ ρ v²

where ρ is the density of fluid  

now we measure the pressure on the included beforehand as a pair of communicating tubes filled with mercury, we set our reference system at the point of the mercury bottom surface

           ΔP =ρ_{Hg} g h - ρ g h

           ΔP =  (ρ_{Hg} - ρ) g h

as the static pressure we can equalize the equations

          ΔP = P₁ - P₂

         (ρ_{Hg} - ρ) g h = ½ ρ v²

         v = [tex]\sqrt{\frac{2 (\rho_{Hg} - \rho) g}{\rho } } \ \sqrt{h}[/tex]

in this expression the densities are constant

        v = A  √h

       A =[tex]\sqrt{\frac{2(\rho_{Hg} - \rho ) g}{\rho } }[/tex]

They indicate the density of mercury rhohg = 13600 kg / m³, the density of dry air at 20ºC is rho air = 1.29 kg/m³

we look for the constant

        A = [tex]\sqrt{\frac{2( 13600 - 1.29) \ 9.8}{1.29} }[/tex]

        A = 454.55

we substitute

       v = 454.55 √h

to calculate the uncertainty or error of the velocity

         h = [tex]\frac{1}{454.55^2} \ v^2[/tex]

       Δh = [tex]\frac{dh}{dv}[/tex]   Δv

       [tex]\frac{\Delta h}{h } = 2 \ \frac{\Delta v}{v}[/tex]

Suppose we have a height reading of h = 20 cm = 0.20 m

a) uncertainty 2.5 m / s ( 0.05)

        [tex]\frac{\delta v}{v} = 0.05[/tex]

       [tex]\frac{\Delta h}{h}[/tex] = 2 0.05  

       Δh = 0.1 h

       Δh = 0.1  20 cm

       Δh = 2 cm

b) uncertainty 0.5 m / s ( Δv/v= 0.01)

        [tex]\frac{\Delta h}{h}[/tex] =  2 0.01

        Δh = 0.02 h

        Δh = 0.02 20

        Δh = 0.1 20 cm

        Δh = 0.4 cm = 4 mm

Answer:

a) 1.9%

b) T2s = 505.5 k = 232.5°C

Explanation:

P1 = 95 kPa

T1 = 27°C  = 300 k

P2 = 600 kPa

T1 = 277°c  = 550 k

Table used : Table ( A - 17 ) Ideal gas properties of air

a) determining the isentropic efficiency of the compressor

Л = ( h2s - h1 ) / ( h2a -  h1 ) ---- ( 1 )

where ; h1 = 300.19 kJ/kg , T1 = 300 K , h2a = 554.74 kJ/kg , T2 = 550 k

To get h2s we have to calculate the the value of Pr2 using Pr1(relative pressure)

 Pr2 = P2/P1 * Pr = ( 600 / 95 ) * 1.306  hence; h2s = 500.72 kJ/kg

back to equation1

Л = 0.019 = 1.9%

b) Calculate the exit temperature of the air if compressor is reversible

if compressor is reversible the corresponding exit temperature

T2s = 505.5 k = 232.5°C

given that h2s = 500.72 kJ/kg

Answer:

what about it?

Explanation:

Answer:

1.49 mm

Explanation:

The modulus of elasticity, Y = stress/strain = σ/ε

σ = F/A where F = load = 68 kN = 68 × 10³ N and A = cross-sectional area of rod = πd²/4 where d = diameter of rod = 3 cm = 3 × 10⁻² m.

ε = ΔL/L where ΔL = change in length of the circular rod and L = length of circular rod = 3.1 ,

So, Y = σ/ε

Y = F/A ÷ ΔL/L

Y = FL/AΔL

making the change in length ΔL subject of the formula, we have

ΔL = FL/AY

substituting the value of A into the equation, we have

So, ΔL = FL/(πd²/4)Y

ΔL = 4FL/πd²Y

Since Y = 200 GPa = 200 × 10⁹ Pa

Substituting the values of the variables into the equation, we have

ΔL = 4FL/πd²Y

ΔL = 4 × 68 × 10³ N × ×3.1 m/[π(3 × 10⁻²m)² × 200 × 10⁹ Pa]

ΔL = 843.2 × 10³ Nm/[9π × 10⁻⁴m² × 200 × 10⁹ Pa]

ΔL = 843.2 × 10³ Nm/[1800π × 10⁵ N]

ΔL = 843.2 × 10³ Nm/5654.87 × 10⁵ N

ΔL = 0.149 × 10⁻² m

ΔL = 1.49 × 10⁻³ m

ΔL = 1.49 mm

The change in length of the circular rod is 1.49 mm

Answer:

(a) the reversible power output of turbine is 5810 kw

(b) The second-law efficiency of he turbine = 86.05%

Explanation:

In state 1: the steam has a pressure of 6 MPa and 600°C. Obtain the enthalpy and entropy at this state.

h1 = 3658 kJ/kg s1=7.167 kJ/kgK

In state 2: the steam has a pressure of 50 kPa and 100°C. Obtain the enthalpy and entropy at this state

h2 = 2682kl/kg S2= 7.694 kJ/kg

Assuming that the energy balance equation given  

Wout=m [h1-h2+(v1²-v2²) /2]

Let

W =5 MW

V1= 80 m/s  V2= 140 m/s

h1 = 3658kJ/kg  h2 = 2682 kJ/kg

∴5 MW x1000 kW/ 1 MW =m [(3658-2682)+ ((80m/s)²-(140m/s)²)/2](1N /1kg m/ s²) *(1KJ/1000 Nm)

m = 5.158kg/s

Consider the energy balance equation given  

Wrev,out =Wout-mT0(s1-s2)

Substitute Wout =5 MW m = 5.158kg/s 7

s1=  7.167 kJ/kg-K            s2= 7.694kJ/kg-K and 25°C .

Wrev,out=(5 MW x 1000 kW /1 MW) -5.158x(273+25) Kx(7.167-7.694)

= 5810 kW

(a) Therefore, the reversible power output of turbine is 5810 kw.

The given values of quantities were substituted and the reversible power output are calculated.

(b) Calculating the second law efficiency of the turbine:  

η=Wout/W rev,out

Let Wout =  5 MW and Wrev,out = 5810 kW  

η=(5 MW x 1000 kW)/(1 MW *5810)  

η= 86.05%

Answer:

The pseudocode is as follows:

Input SalesAmount

Input CommissionRate

CommissionEarned= SalesAmount * (CommissionRate/100)

Print CommissionEarned

Explanation:

This gets input for SalesAmount

Input SalesAmount

This gets input for CommissionRate

Input CommissionRate

This calculates the CommissionEarned

CommissionEarned= SalesAmount * (CommissionRate/100)

This prints the calculated CommissionEarned

Print CommissionEarned

Answer:

The heat input from the combustion phase is 2000 watts.

Explanation:

The energy efficiency of the heat engine ([tex]\eta[/tex]), no unit, is defined by this formula:

[tex]\eta = \frac{\dot W}{\dot Q}[/tex] (1)

Where:

[tex]\dot Q[/tex] - Heat input, in watts.

[tex]\dot W[/tex] - Power output, in watts.

If we know that [tex]\dot W = 600\,W[/tex] and [tex]\eta = 0.3[/tex], then the heat input from the combustion phase is:

[tex]\eta = \frac{\dot W}{\dot Q}[/tex]

[tex]\dot Q = \frac{\dot W}{\eta}[/tex]

[tex]\dot Q = \frac{600\,W}{0.3}[/tex]

[tex]\dot Q = 2000\,W[/tex]

The heat input from the combustion phase is 2000 watts.

Answer:

53 sec / cycle

Explanation:

Displayed red time = 35 seconds

Start up lost time = 2 seconds

Yellow time = 4 seconds

Red time = 1 second

Total lost time L = 2n + r

L = lost time

n = number of phase

R = red time

35+2+4+4*1

= 45

L = 2x4+45

= 53 sec/cycle

The total lost time is typically calculated as 53 seconds per cycle

Answer:

The right answer is "16.5 hrs".

Explanation:

Given values are:

[tex]x_1=2.6 \ mm[/tex]

[tex]t_1=3 \ hrs[/tex]

[tex]x_2=6.1 \ mm[/tex]

As we know,

⇒ [tex]\frac{x^2}{Dt}=constant[/tex]

or,

⇒ [tex]\frac{x_1^2}{t_1} =\frac{x_2^2}{t_2}[/tex]

⇒ [tex]t_2=(\frac{x_2}{x_1})^2\times t_1[/tex]

By putting the values, we get

       [tex]=(\frac{6.1}{2.6} )^2\times 3[/tex]

       [tex]=5.5\times 3[/tex]

       [tex]=16.5 \ hrs[/tex]      

Answer:

I can't understand this language .

Answer:

1.c

2.c

3.c

Explanation:

James is a  pilot, whistle. He is wearing a flight suit. Paris is the palace where does he fly to. Hence, option C, C, and C are correct.

When flying an aircraft, such as a military aircraft, a glider, or a helicopter, one must wear a full-body suit called a flight suit. These outfits are typically meant to keep the user warm and are also functional (they have many of pockets) (including fire ). In most cases, it looks like a jumpsuit.

The G suit, sometimes known as a "anti-G suit," is a one-piece jumpsuit that shields a pilot from the pressure of G forces pressing down on him and causing discomfort or unconsciousness.

The traditional attire for pilots of military and commercial aircraft, helicopters, and even gliders is flight suits or flyers coveralls. In areas where there is a risk of fire, ground personnel—including aircrews—often wear flight suits as well.

Thus, option C, C, and C are correct.

For more information about point of a flight suit, click here:

https://brainly.com/question/12302183

#SPJ2

Answer: [tex]10.631\times 10^3\ N/m^2[/tex]

Explanation:

Given

Discharge is [tex]Q=12.5\ L[/tex]

Diameter of pipe [tex]d=150\ mm[/tex]

Distance between two ends of pipe [tex]L=800\ m[/tex]

friction factor [tex]f=0.008[/tex]

Average velocity is given by

[tex]\Rightarrow v_{avg}=\dfrac{12.5\times 10^{-3}}{\frac{\pi }{4}(0.15)^2}\\\\\Rightarrow v_{avg}=\dfrac{15.9134\times 10^{-3}}{2.25\times 10^{-2}}\\\\\Rightarrow v_{avg}=7.07\times 10^{-1}\\\Rightarrow v_{avg}=0.707\ m/s[/tex]

Pressure difference is given by

[tex]\Rightarrow \Delta P=f\ \dfrac{L}{d}\dfrac{\rho v_{avg}^2}{2}\\\\\Rightarrow \Delta P=0.008\times \dfrac{800}{0.15}\times \dfrac{997\times (0.707)^2}{2}\\\\\Rightarrow \Delta P=10,631.45\ N/m^2\\\Rightarrow \Delta P=10.631\ kPa[/tex]

Answer:

there are generally two types of toilet bowl types- round and elongated.

Answer:

Explanation:

#include<iostream>

using namespace std;

int main()

{

int n1,n2;

cout<<"Enter a number:"<<endl; //Entering first number

cin>>n1;

cout<<"Enter a number:"<<endl; //Entering second number

cin>>n2;

if(n1%2==0 && n1%2==0) //Checking whether the two number are even or not

{

if(n1>n2)

{

cout<<n1<<" is the larger number"<<endl;

}

else if(n1==n2)

{

cout<<"Numbers are equal"<<endl;

}

else

{

cout<<n2<<" is the larger number"<<endl;

}

}

else

{

cout<<"The number are not even"<<endl;

}

}

Answer:

There are several different types of charts and graphs. The four most common are probably line graphs, bar graphs and histograms, pie charts, and Cartesian graphs. They are generally used for, and are best for, quite different things. ... Pie charts to show you how a whole is divided into different parts.

#carryonlearning