1. 00L of a gas at 1. 00atm is compressed to 0. 437L. What is the new pressure of the gas

Given the equilibrium reaction H₂ (g) + Br₂ (g) ⇌ 2 HBr (g), if Kc = 1.90 × 10¹⁹ at 25.0 °C, then Kp = 6.44 × 10⁵. The answer is C)

The equilibrium constant, Kc, is defined as the ratio of the concentrations of the products to the concentrations of the reactants, each raised to the power of their stoichiometric coefficients, at equilibrium.

In contrast, the equilibrium constant in terms of partial pressures, Kp, is defined as the ratio of the partial pressures of the products to the partial pressures of the reactants, each raised to the power of their stoichiometric coefficients, at equilibrium.

To calculate Kp from Kc, we can use the expression Kp = Kc(RT)^(Δn), where R is the gas constant, T is the temperature in kelvins, and Δn is the change in the number of moles of gas between products and reactants (in this case, Δn = 2 - 2 = 0).

Plugging in the given values, we get:

Kp = (1.90 × 10¹⁹) * ((0.0821 L atm K⁻¹ mol⁻¹) * (298 K))^0

= 6.44 × 10⁵

Therefore, the answer is C) 6.44 × 10⁵.

To know more about equilibrium, refer here:

https://brainly.com/question/5537989#

#SPJ11

Cu(NO3)2 with molar analytical concentration "m" has a potential of 0.256 V at fixed pH of 4.00. No information provided for "is m ()".

The given solution contains Cu(NO3)2 at a concentration of "m" with a fixed pH of 4.00, resulting in a potential of 0.256 V. The potential of a solution depends on the concentration and identity of the ions present, as well as the pH of the solution. The information provided is not sufficient to determine the concentration or identity of the second species "is m ()".

Learn more about pH here:

https://brainly.com/question/491373

#SPJ11

The classification of each acid as strong or weak and its expression for acid ionization is as follows:

a. HF is a weak acid. The ionization expression for its acid ionization constant[tex](Ka) is: Ka = [H+][F-]/[HF][/tex]
b. HNO3 is a strong acid. As a strong acid, it does not have a Ka value because it completely ionizes in water.

c. H2CO3 is a weak polyprotic acid with two ionizations.
1st ionization: [tex]H2CO3 → H+ + HCO3-, Ka1 = [H+][HCO3-]/[H2CO3][/tex]
2nd ionization: [tex]HCO3- → H+ + CO3(2-), Ka2 = [H+][CO3(2-)]/[HCO3-][/tex]

The Ka2 value for this reaction is even smaller than the Ka1 value, indicating that only a very small percentage of HCO3- ions will ionize in water to produce H3O+ ions and CO32- ions.

To learn more about acid, refer below:

https://brainly.com/question/14072179

#SPJ11

The final pressure in the water bottle at 45 °C will be 1044 mm Hg, assuming the volume doesn't change using combined gas law.

Thus, the combined gas law can be used to estimate the final pressure  which is (P1 x V1) / T1 = (P2 x V2) / T2 where P1 is equal to 772 mm Hg, V1 is equal to 490.0 mL, and T1 is equal to 292.15 K. V2 is equal to V1 = 490.0 mL assuming the volume doesn't change, and the final temperature in Kelvin is equal to 318.15 K.

The equation of combined gas law can be rearranged to solve for P2 which is final pressure:

P2 = (P1 x V1 x T2) / (V2 x T1)

P2 = (772 mm Hg x 490.0 mL x 318.15 K) / (490.0 mL x 292.15 K)

P2 = 1044 mm Hg

Learn more about the combined gas law here:

https://brainly.com/question/30458409

#SPJ1

The ionization energy of a hydrogen atom in its ground state is 13.6 electron volts (eV) or 1.09678×10−2 nm−1.

This energy is the amount of energy required to remove the electron from the hydrogen atom when it is in its lowest energy state, or ground state. When the electron is removed, the hydrogen atom becomes a positively charged ion. The ionization energy of a hydrogen atom is important in understanding the behavior of atoms and molecules in chemical reactions and in many other areas of physics and chemistry. It is also used in calculating the energy levels of other atoms and molecules, and in determining the properties of materials such as metals and semiconductors.

Overall, the ionization energy of a hydrogen atom is a fundamental property of matter that has important implications in many areas of science.

To know more about ionization energy visit:

https://brainly.com/question/28385102

#SPJ11

The metal complex cis-[Ru(bipy)2Cl2] is chiral and has an optical isomer, while the metal complex [Zn(H2O)2Cl2] and trans-[Ru(bipy)2Cl2] are not chiral.
A metal complex is chiral if it lacks a plane of symmetry or an axis of rotation that allows it to be superimposed on its mirror image. In other words, a chiral metal complex has a non-superimposable mirror image or an optical isomer.

The metal complex cis-[Ru(bipy)2Cl2] is chiral because it has a plane of symmetry that cuts through two ligands but not through the other two. Therefore, it has a non-superimposable mirror image or an optical isomer.

On the other hand, the metal complex [Zn(H2O)2Cl2] and trans-[Ru(bipy)2Cl2] both have planes of symmetry that can bisect the molecule and divide it into two identical halves. Hence, they lack a non-superimposable mirror image and are not chiral.

learn more about chiral

https://brainly.com/question/9522537

#SPJ11

The 24.4 grams of NaOH are produced from 20.0 grams of Na2CO3. The correct answer is 24.4 grams.


To determine the number of grams of NaOH produced from 20.0 grams of Na2CO3, we need to calculate the molar mass of NaOH and use stoichiometry.

The molar mass of NaOH is calculated as follows:
Na: 22.989 g/mol
O: 15.999 g/mol
H: 1.008 g/mol
Total: 40.996 g/mol

Next, we need to use stoichiometry to relate Na2CO3 and NaOH. From the balanced equation, we can see that 1 mol of Na2CO3 produces 2 mol of NaOH.

First, we calculate the number of moles of Na2CO3 using its molar mass:
20.0 g Na2CO3 / (2 * 22.989 g/mol + 12.01 g/mol + 3 * 15.999 g/mol) = 0.295 mol Na2CO3

Since the stoichiometric ratio is 1:2 (Na2CO3:NaOH), we multiply the number of moles of Na2CO3 by 2 to find the moles of NaOH produced:
0.295 mol Na2CO3 * 2 = 0.59 mol NaOH

Finally, we convert moles to grams using the molar mass of NaOH:
0.59 mol NaOH * 40.996 g/mol = 24.4 grams of NaOH



To learn more about molar mass click here
brainly.com/question/31545539


#SPJ11

The absorbed dosage in rad is 0.002 Gy. The effective dose in rem is 0.02 Sv.

The calculation of the absorbed dose and effective dose involves the use of some radiation units.

The absorbed dose is measured in Gray (Gy), where 1 Gy is equal to the absorption of 1 Joule of energy per kilogram of matter.

The effective dose is measured in Sievert (Sv), where 1 Sv is equal to the product of the absorbed dose and a weighting factor that reflects the biological effectiveness of the radiation type (in this case, the RBE values given).

Given the mass of the person, we can use the absorbed dose formula to calculate the absorbed dose:

Part A: absorbed dose = energy / mass

absorbed dose = 0.10 J / 50 kg = 0.002 Gy

Therefore, the absorbed dose is 0.002 Gy.

To calculate the effective dose, we need to use the formula:

Part B: effective dose = absorbed dose x weighting factor

For alpha radiation, the RBE is 10. For gamma and beta radiation, the RBE is approximately 1.

effective dose for alpha radiation = 0.002 Gy x 10 = 0.02 Sv

effective dose for gamma and beta radiation = 0.002 Gy x 1 = 0.002 Sv

Since the person was uniformly irradiated by 0.10-J alpha radiation, we assume that the entire effective dose is due to alpha radiation. Therefore, the effective dose is 0.02 Sv.

Know more about Sievert here

https://brainly.com/question/31830211#

#SPJ11

The processes to obtain crystals of hydrated copper sulfate are . First, the solution needs to be filtered (2) to separate any solid impurities. Then, solution is concentrated.

(1) to increase the concentration of copper(II) sulfate. After concentration, the solution is allowed to cool and crystallize, and the crystals are heated (process 3) to remove the water of hydration and obtain anhydrous copper(II) sulfate crystals. Finally, the obtained crystals are washed (process 4) to remove any remaining impurities.

Process 2 (filtering) is performed initially to remove solid impurities from the solution. This ensures that only the desired copper(II) sulfate is present. Then, process 1 (concentration) is carried out to increase the concentration of copper(II) sulfate in the solution, making it easier to obtain crystals upon cooling. After the solution has been concentrated, process 2 (cooling and crystallization) occurs naturally as the solution cools down, allowing the copper(II) sulfate to crystallize.

Once the crystals have formed, process 3 (heating) is applied to remove the water of hydration, resulting in anhydrous copper(II) sulfate crystals. Finally, process 4 (washing) is performed to remove any impurities that might be present on the surface of the crystals, ensuring their purity.

To learn more about hydrated copper sulfate click here : brainly.com/question/29039165

#SPJ11

The experimental yield of alum may be greater than, less than, or equal to the theoretical yield depending on factors such as reactant purity, reaction conditions, and product isolation techniques.

The theoretical yield of a chemical reaction is the maximum amount of product that can be obtained based on the stoichiometry of the reactants. It is calculated based on the balanced chemical equation and assumes that the reaction proceeds to completion without any side reactions, losses, or errors.

In contrast, the experimental yield is the actual amount of product obtained from a chemical reaction under real conditions. It is influenced by several factors, such as the purity of the reactants, the reaction conditions, the efficiency of the reaction, and the techniques used for product isolation and purification.

Therefore, the experimental yield of alum can be greater than, less than, or equal to the theoretical yield depending on these factors. For instance, if the reactants are impure or the reaction conditions are not optimal, the experimental yield may be lower than the theoretical yield due to incomplete reaction, side reactions, or losses.

On the other hand, if the reactants are pure and the reaction conditions are carefully controlled, the experimental yield may approach or exceed the theoretical yield. However, even under ideal conditions, it is rare for the experimental yield to match the theoretical yield due to experimental uncertainties and limitations.

In conclusion, the experimental yield of alum can vary from the theoretical yield depending on various factors, and the two values are not necessarily equal.

Careful experimental design and optimization can improve the yield, but some discrepancies are expected due to practical limitations and experimental uncertainties.

For more question on alum visit:

https://brainly.com/question/28299913

#SPJ11

The power of the laser is 2.24 W. We can use the formula for heat, q = mcΔT, to find the amount of energy required to heat the aluminum.

Here, m = 7.00 g, c = 0.900 J/gºC, and ΔT = (103-23) = 80 ºC. Substituting these values, we get q = (7.00 g) x (0.900 J/gºC) x (80 ºC) = 504 J.

Next, we can use the formula for power, P = q/t, where t is the time in seconds. Converting 3.75 minutes to seconds, we get t = 225 s. Substituting the values, we get P = (504 J) / (225 s) = 2.24 W.

Therefore, the power of the laser is 2.24 W.

To know more about energy, refer here:

https://brainly.com/question/16983187#

#SPJ11

The virtual address is composed of 7 bits for the page number and 10 bits for the offset and the physical address is composed of 5 bits for the frame number and 10 bits for the offset.

(a) To calculate the number of bits in a virtual address, we first find the total number of bytes in the address space:

96 pages x 1,024 bytes per page = 98,304 bytes

Since each byte has a unique address, we need log2(98,304) bits for the virtual address.

To determine the number of bits that make up the page number and the offset, we need to know the page size. Assuming a page size of 1,024 bytes, we have:

Page number bits = log2(96) = 7 bits

Offset bits = log2(1,024) = 10 bits

(b) Since the system has 32 frames of physical memory, we need log2(32) = 5 bits to represent the frame number in a physical address.

Assuming a page size of 1,024 bytes, the number of bits in a physical address is also 17 (5 bits for frame number and 10 bits for offset).

For more such questions on virtual address:

https://brainly.com/question/28261277

#SPJ11

The virtual address has 17 bits, with 7 bits for the page number and 10 bits for the offset. The physical address has 15 bits, with 5 bits for the page number and 10 bits for the offset.

(a) In this system, there are 96 pages of 1,024 bytes each, which makes the virtual address space size 96 x 1,024 bytes. To represent 96 pages, we need 7 bits (since 2^6 = 64 < 96 ≤ 2^7 = 128). To represent 1,024 bytes, we need 10 bits (since 2^10 = 1,024). Therefore, there are 7 bits for the page number and 10 bits for the offset, making a total of 17 bits in a virtual address.
(b) The system has 32 frames in physical memory. To represent 32 frames, we need 5 bits (since 2^5 = 32). Since each frame also has 1,024 bytes, we still need 10 bits for the offset. Hence, there are 5 bits for the page number and 10 bits for the offset, making a total of 15 bits in a physical address.

learn more about virtual address Refer: https://brainly.com/question/28261277

#SPJ11

To determine the number of millimoles of HCl in 130 mL of a 10% solution, we need to calculate the amount of HCl in grams and then convert it to millimoles using the molecular weight.

First, let's find the amount of HCl in grams. The 10% solution means that 10 g of HCl is present in 100 mL of the solution. Therefore, in 130 mL, we can calculate the amount of HCl as (10 g/100 mL) * 130 mL = 13 g. Next, we convert the mass of HCl to millimoles using the molecular weight. The molecular weight of HCl is 36.5 g/mol. To convert grams to millimoles, we divide the mass by the molecular weight. So, (13 g) / (36.5 g/mol) = 0.356 millimoles. Therefore, there are approximately 0.356 millimoles of HCl in 130 mL of a 10% solution.

Learn more about molecular weight here:

https://brainly.com/question/20380323

#SPJ11

A dose is the amount of a material would need to give approximately 0.4 ml of abc 1.2 g/2 ml to provide 260 mg of abc.

To determine how many milliliters of abc 1.2 g/2 ml you need to give to provide 260 mg of abc, you can use the following formula:

ml = (mg needed ÷ strength in mg/ml)

First, convert the strength of abc from 1.2 g/2 ml to mg/ml:

1.2 g/2 ml = 1200 mg/2 ml = 600 mg/ml

Now, substitute the values into the formula:

ml = (260 mg ÷ 600 mg/ml) ≈ 0.4 ml (rounded to the nearest tenth)

Therefore, you would need to give approximately 0.4 ml of abc 1.2 g/2 ml to provide 260 mg of abc.

Learn more about dose: brainly.com/question/29725527

#SPJ11

The order of decreasing rate of effusion for the given gases is:

H2 > He = Ne > CO > Ar > C4H8

This means that hydrogen (H2) will effuse the fastest, followed by helium (He) and neon (Ne) at the same rate, then carbon monoxide (CO), argon (Ar), and finally butane (C4H8) with the slowest effusion rate. This order is determined by Graham's law of effusion, which states that the rate of effusion of a gas is inversely proportional to the square root of its molar mass. Since hydrogen has the lowest molar mass, it will effuse the fastest, while butane has the highest molar mass and therefore the slowest effusion rate. The other gases fall somewhere in between based on their respective molar masses.

learn more about gases here:

https://brainly.com/question/1369730

#SPJ11

The calculation shows that the pH of a 0.045 M aqueous solution of aspirin is approximately 2.8, indicating that the solution is acidic.

To determine the pH of a 0.045 M aqueous solution of aspirin, we need to first understand its acid-base behavior.

Aspirin is a weak acid and undergoes partial ionization in water to produce its conjugate base ([tex]C_{9}H_{7}O_{4}[/tex]) and a hydronium ion (H3O+). The ionization constant of aspirin, Ka, is given as 3.1 x[tex]10^{4}[/tex] in the problem.

Using the Ka value and the initial concentration of aspirin, we can calculate the concentration of the hydronium ion using the equation for the ionization of a weak acid.

From there, we can use the equation for pH, which is defined as the negative logarithm of the hydronium ion concentration, to calculate the pH of the solution.

The calculation shows that the pH of a 0.045 M aqueous solution of aspirin is approximately 2.8, indicating that the solution is acidic.

This pH value falls within the typical range for weak acids, which generally have pH values in the range of 2 to 7.

To know more about aqueous solution, refer here:

https://brainly.com/question/14097392#

#SPJ11

The e° for the reaction Cu⁺ → Cu²⁺ + e⁻ is 0.18 V.

To find the e° for the overall reaction, we need to subtract the e° value for the reduction half-reaction from the e° value for the oxidation half-reaction:

Cu⁺ + e⁻ → Cu°   E°(reduction) = 0.52 V (reduction half-reaction)
Cu²⁺ + 2e⁻ → Cu°   E°(reduction) = 0.34 V (reduction half-reaction)

To find E°(oxidation), reverse the E° value for the reduction half reaction so that overall value of E°cell is positve.
Cu° → Cu²⁺ + 2e⁻   E°(oxidation) = -0.34 V (oxidation half-reaction)

The overall reaction is thus:
Cu⁺ + e⁻ → Cu°  
Cu° → Cu²⁺ + 2e⁻
=Cu⁺ → Cu²⁺ + e⁻  

E°cell = E°(reduction) + E°(oxidation) = 0.52 V + (-0.34 V) = 0.18 V

Therefore, standard cell potential (E°cell) is 0.18 V.

To learn more about E°cell visit:

https://brainly.com/question/19036092

#SPJ11

The pH of the buffer solution containing 0.0059 M HC₅H₅NCl and 0.0098 M C₅H₅N, with a Ka of 5.88×10⁻⁶, is approximately 5.46.

To calculate the pH of the buffer solution, we need to consider the equilibrium between the weak acid HC₅H₅NCl (conjugate acid) and its conjugate base C₅H₅N (weak base). The dissociation of the weak acid can be represented by the equation:

HC₅H₅NCl ⇌ H⁺ + C₅H₅N

To calculate the pH, we need to determine the concentration of H⁺ ions in the solution. Since this is a buffer solution, we assume that the weak acid is only partially dissociated.

First, we calculate the concentration of H⁺ ions using the equation for the dissociation of the weak acid:

Ka = [H⁺][C₅H₅N] / [HC₅H₅NCl]

We rearrange the equation to solve for [H⁺]:

[H⁺] = (Ka * [HC₅H₅NCl]) / [C₅H₅N]

[H⁺] = (5.88×10⁻⁶ * 0.0059) / 0.0098

[H⁺] = 3.51×10⁻⁶ M

Now we can calculate the pH using the concentration of H⁺ ions:

pH = -log[H⁺]

pH = -log(3.51×10⁻⁶)

pH ≈ 5.46

Learn more about The Buffer: https://brainly.com/question/31605089

#SPJ11

In the balanced equation for the reaction[tex]MnO_{4}^-(aq) + Fe_{2} ^+(aq) -- > Mn_{2}^+(aq) + Fe_{3}^+(aq)[/tex] in basic aqueous solution, the coefficient for OH−(aq) is 4.

To balance the given equation in basic aqueous solution, we need to ensure that the number of atoms of each element is equal on both sides of the equation and that the overall charge is balanced. Here's how the equation is balanced:

First, we balance the atoms other than hydrogen and oxygen. The equation becomes:

[tex]MnO_{4}^-(aq) + 5Fe_{2} ^+(aq)+8H_{2}O(l) -- > Mn_{2}^+(aq) +5 Fe_{3}^+(aq)[/tex]

Next, we balance the oxygen atoms by adding water molecules (H2O):

[tex]MnO_{4}^-(aq) + 5Fe_{2} ^+(aq)+8H_{2}O(l) -- > Mn_{2}^+(aq) +5 Fe_{3}^+(aq)+4H_{2}O(l)[/tex]

Now, we balance the hydrogen atoms by adding OH−(aq) ions:

[tex]MnO_{4}^-(aq) + 5Fe_{2} ^+(aq)+8H_{2}O(l) -- > Mn_{2}^+(aq) +5 Fe_{3}^+(aq)+4H_{2}O(l)+4OH^-(aq)[/tex]

Therefore, in the balanced equation, the coefficient for OH−(aq) is 4. This balances the hydrogen atoms and ensures that the equation is balanced in basic aqueous solution.

Learn more about aqueous solution here:

https://brainly.com/question/1382478

#SPJ11

The δg for the reaction is –49.22 kj. It indicates that the reaction is spontaneous and proceeds in the forward direction under the given conditions.

To calculate δg for the given reaction, we need to use the equation:
δg = δg° + RTln(Q)
where δg° is the standard Gibbs free energy change, R is the gas constant, T is the temperature, Q is the reaction quotient.
From the given information, we have δg° = –23.25 kj and the reaction is:
H2(g) + I2(g) → 2HI(g)
Now, let's find Q for the reaction:
Q = (p(HI))^2 / (p(H2) x p(I2))
where p denotes pressure.
Given that H2 and I2 are supplied at 10.0 atm pressure and HI is at 1.00 atm pressure, we can substitute the values into the equation:
Q = (1.00)^2 / (10.0 x 10.0) = 0.010
Now, substituting the values into the equation for δg, we get:
δg = –23.25 kj + (8.314 J/mol*K x 699 K x ln(0.010)) = –49.22 kj
The decrease in pressure of the products also drives the reaction forward, as per Le Chatelier's principle.

To know more about pressure visit:

brainly.com/question/31478113

#SPJ11

The amount of water that has condensed out of the mixture is 0.0106 lbm of water per lbm of dry air.

To solve this problem, we need to use the steam tables to find the state of the air-water mixture before and after the expansion. We can then calculate the amount of water that has condensed out of the mixture.

Using the steam tables, we can find that the initial state of the air-water mixture is:

Temperature = 400°F = 977.67 R

Pressure = 100 psia

Humidity ratio = 0.024 lbm H2O/lbm dry air

From this information, we can determine the specific enthalpy and specific entropy of the mixture using the tables. We can then use these values to find the state of the mixture after the expansion to 15 psia in an isentropic nozzle.

Assuming the expansion is reversible and adiabatic, we can use the isentropic relations to find the final state of the mixture:

Pressure = 15 psia

Entropy = initial entropy = 1.7355 Btu/lbm·R

From this information, we can use the steam tables to find the final temperature and humidity ratio of the mixture:

Temperature = 389.5°F = 961.67 R

Humidity ratio = 0.0134 lbm H2O/lbm dry air

The difference in humidity ratio between the initial and final states represents the amount of water that has condensed out of the mixture:

ΔW = initial humidity ratio - final humidity ratio = 0.024 lbm/lbm - 0.0134 lbm/lbm = 0.0106 lbm/lbm

For more such questions on condensed visit:

https://brainly.com/question/30956356

#SPJ11

To draw a Lewis structure for SO2, we first need to determine the number of valence electrons in each atom. Sulfur has 6 valence electrons and each oxygen has 6 valence electrons, for a total of 18 valence electrons.

We place the sulfur atom in the centre, surrounded by the two oxygen atoms. Each oxygen atom forms a single bond with the sulfur atom, using up 4 of the 18 valence electrons. This leaves 14 valence electrons.
We then distribute the remaining electrons as unshared pairs on the oxygen atoms, as they have the highest electronegativity. Each oxygen atom has 2 unshared pairs of electrons. This fills the octet for each oxygen atom but leaves the sulfur atom with only 6 valence electrons.
To satisfy the octet rule for the sulfur atom, we can convert one of the oxygen-sulfur single bonds into a double bond, using up 2 more valence electrons and giving the sulfur atom a total of 8 valence electrons.
Therefore, the number of unshared pairs on the central S atom is 0. The central S atom forms 2 single bonds and 1 double bond.  The Lewis structure for SO2 has the central S atom obeying the octet rule by forming 2 single bonds and 1 double bond with the surrounding O atoms. The central S atom has 0 unshared pairs of electrons.

Learn more about electronegativity here ;

https://brainly.com/question/3393418

#SPJ11

The charge of the complex ion in [Zn(H2O)3Cl]Cl is 1- (option B).

The complex ion in [Zn(H2O)3Cl]Cl is a coordination compound where Zn is the central metal ion coordinated to three water molecules and one chloride ion. The charge on the complex ion can be determined by considering the charge on the ligands (water and chloride) and the central metal ion (Zn). The water molecules are neutral, and the chloride ion has a charge of 1-.

The overall charge on the complex ion can be calculated by summing the charges on the ligands and the central metal ion. Zn is a transition metal and can have different oxidation states. However, in this case, it is coordinated to three neutral water molecules and one negatively charged chloride ion. Therefore, the net charge on the complex ion is the charge on the chloride ion, which is 1-.

Hence, the charge of the complex ion in [Zn(H2O)3Cl]Cl is 1- (option B). In summary, the complex ion has a net negative charge due to the presence of a negatively charged chloride ion, and the central metal ion is in a 2+ oxidation state to balance the charge.

To know more about chloride ion visit:

https://brainly.com/question/31828400

#SPJ11

The amount of metal deposited on an electrode during electrolysis is directly proportional to number of moles of electrons transferred to the electrode. Option d is correct.

The metal that requires the fewest number of electrons to be reduced will be deposited with smallest mass of metal for a given amount of current and time.

The reduction half-reactions for Fe, Ni, Cu, and Ag are:

[tex]Fe_2+(aq)[/tex] + 2e- → Fe(s) (2 electrons transferred)

[tex]Ni_2+(aq)[/tex] + 2e- → Ni(s) (2 electrons transferred)

[tex]Cu_2+(aq)[/tex] + 2e- → Cu(s) (2 electrons transferred)

Ag+(aq) + e- → Ag(s) (1 electron transferred)

Since Ag+ requires only one electron for reduction, it would deposit the smallest mass of metal.

Therefore, correct answer is option d Ag found in [tex]AgNO_3(aq)[/tex].

To know more about electrolysis, here

brainly.com/question/31726896

#SPJ4

The molar solubility of PbBr₂ in a 0.2740 M Pb(NO₃)₂ solution is 0.0547 M.

The molar solubility of PbBr₂ in a 0.2740 M lead(II) nitrate, Pb(NO₃)₂, solution can be calculated using the common ion effect. Write the balanced equation for the dissolution of PbBr₂ in water:

PbBr₂(s) ⇌ Pb²⁺(aq) + 2Br⁻(aq)

Write the expression for the solubility product constant (Ksp) of PbBr₂:

Ksp = [Pb²⁺][Br⁻]²

Calculate the initial concentration of Pb²⁺ in the solution:

[Pb²⁺] = 0.2740 M

Use the common ion effect to calculate the equilibrium concentration of Br⁻ ions:

Ksp = [Pb²⁺][Br⁻]²

[Br⁻]² = Ksp / [Pb²⁺] = (6.60 × 10⁻⁶) / (0.2740) = 2.41 × 10⁻⁵

[Br⁻] = √(2.41 × 10⁻⁵) = 0.00491 M

Calculate the molar solubility of PbBr₂ using the equilibrium concentration of Br⁻ ions:

PbBr₂(s) ⇌ Pb²⁺(aq) + 2Br⁻(aq)

[PbBr₂] = Ksp / ([Pb²⁺][Br⁻]²) = (6.60 × 10⁻⁶) / (0.2740 × (0.00491)²) = 0.0547 M

Therefore, PbBr₂ has a molar solubility of 0.0547 M in a 0.2740 M Pb(NO₃)₂ solution. This calculation shows how the presence of a common ion (in this case, Pb²⁺) can affect the solubility of a slightly soluble salt (in this case, PbBr₂) through the common ion effect.

To know more about the Molar solubility, here

https://brainly.com/question/31435315

#SPJ4

If a bottle of champagne contains 730 ml of liquid, then it contains 87.6 ml of alcohol.

The alcohol content of champagne can vary, but typically it is around 12% alcohol by volume (ABV). Therefore, if there are 730 ml of champagne in the bottle, the amount of alcohol present can be calculated as follows:

Alcohol content = volume of champagne x ABV

Alcohol content = 730 ml x 0.12

Alcohol content = 87.6 ml

Therefore, there are approximately 87.6 milliliters of alcohol present in the 730 ml bottle of champagne.

To know more about the alcohol refer here :

https://brainly.com/question/14229343#

#SPJ11

The overall equation for the reaction that produces P4O10 from P4O6 and O2 is: P4O6(s) + 4O2(g) → P4O10(s). This equation shows the balanced stoichiometry between P4O6 and O2, resulting in the formation of P4O10.

In the given equation, P4O6 is combined with oxygen gas (O2) to produce phosphorus pentoxide (P4O10). The coefficients in the equation indicate the balanced ratio between the reactants and products. According to the equation, one molecule of P4O6 reacts with four molecules of O2 to yield one molecule of P4O10.

This balanced equation represents the overall reaction between P4O6 and O2 to form P4O10. It shows the stoichiometry of the reaction, indicating the specific number of molecules involved in the process. The coefficients in the equation ensure that the law of conservation of mass is satisfied, meaning that the total number of atoms of each element is the same on both sides of the equation.

To learn more about balanced stoichiometry click here :  brainly.com/question/30808199

#SPJ11

The equilibrium constant, Kc, can be calculated using the concentrations of the reactants and products at equilibrium.

Kc = [SO3]^2 / ([S]^2 [O2]^3)

Substituting the given equilibrium concentrations, we get:

Kc = (0.95 M)^2 / ((0.70 M)^2 (1.3 M)^3)

Kc = 0.161

Therefore, the value of Kc for the given reaction is 0.161.

To calculate the equilibrium constant, Kc, we use the equilibrium concentrations of the reactants and products. The equation for Kc involves the molar concentrations of the products raised to their stoichiometric coefficients divided by the molar concentrations of the reactants raised to their stoichiometric coefficients. In this case, the stoichiometric coefficients of S and O2 are 2 and 3, respectively, while the stoichiometric coefficient of SO3 is also 2. Substituting the given equilibrium concentrations in the equation for Kc gives us the value of Kc for the reaction.

To know more about stoichiometric visit

https://brainly.com/question/29856106

#SPJ11

The pH of a 0.103 M solution of formic acid is 2.26.

The balanced chemical equation for the dissociation of formic acid in water is:

[tex]HCOOH + H_2O = H_3O^+ + HCOO^-[/tex]

The equilibrium constant expression for this reaction is:

[tex]Ka = [H_3O^+][HCOO^-]/[HCOOH][/tex]

We also know that the dissociation constant of the conjugate base ([tex]HCOO^-[/tex]) is related to the acid dissociation constant (Ka) by:

Kb = Kw/Ka

where Kw is the ion product constant of water (1.0x10^-14 at 25°C).

The pKa and pKb values for formic acid and formate ion, respectively, are provided on the equation sheet:

pKa(HCOOH) = 3.75

pKb([tex]HCOO^-[/tex]) = 10.25

Using these values, we can calculate the equilibrium concentrations of [tex]H_3O^+[/tex] and [tex]HCOO^-[/tex] in a 0.103 M solution of formic acid.

First, we can calculate Ka from the pKa value:

[tex]Ka = 10^{-pKa} = 10^{-3.75} = 1.78*10^{-4}[/tex]

Then, we can use Kb to calculate the equilibrium concentration of [tex]HCOO^-[/tex]:

Kb = Kw/Ka = 1.0x10^-14/1.78x10^-4 = 5.62x10^-11

[tex][HCOO^-] = \sqrt{(Kb*[HCOOH])} \\\= \sqrt{(5.62*10^{-11}*0.103)} = 3.34*10^{-6} M[/tex]

[tex][H_3O^+] = Ka*[HCOOH]/[HCOO^-] \\= 1.78*10^{-4}*0.103/3.34*10^{-6} = 5.5*10^{-3} M[/tex]

Finally, we can calculate the pH of the solution:

[tex]pH = -log[H_3O^+] \\= -log(5.5*10^{-3}) = 2.26[/tex]

For more question on pH click on

https://brainly.com/question/172153

#SPJ11

The correct answer would be E) None of these, because the weak acid concomium represents the highest pH limit for an effective buffer

The pH of a buffer solution is determined by the ratio of the conjugate base concentration ([A-]) to the weak acid concentration ([HA]). The higher the ratio [A-]/[HA], the higher the pH of the buffer solution. By analyzing the given options (A, B, C, D), we can determine that none of them represents the highest pH limit for an effective buffer.

Therefore, the correct answer is E) None of these.

To understand the concept of pH and the role of buffers in maintaining pH stability, it is important to learn about the Henderson-Hasselbalch equation, which relates the pH of a buffer solution to the concentrations of the weak acid and its conjugate base.

This equation is fundamental in understanding buffer systems and their applications.

Learn more about buffer

brainly.com/question/31847096

#SPJ11